Search NASA⌕ Search

SEARCH · Search NASA

Results for “continuous simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Quantifying Leak Rates and Vacuum Impact on Granular Soil Column Pneumatic Seal

Introduction: All In-Situ Resource Utilization (ISRU) regolith reactor systems that aim to extract gases or vapors must maintain a seal along the flow path of the regolith from the inlet hopper to where extracted gases or vapors are generated. Using a column of regolith at the inlet has been proposed as an alternative to systems using series of mechanical valves to reduce mass and complexity. Preliminary investigations into the use of regolith itself as a barrier to escaping fluids have been conducted, which this research seeks to expand upon. Different vertical regolith simulant plug diameters and heights were tested under vacuum with dry nitrogen to observe leak rates and approximate steady state pressure gradient equilibria. The effect of absolute ambient pressure was also studied by repeating tests at incremental pressures ranging from 10e-5 Torr up to 1 atm to corroborate ambient bench tests from previous work. The impact of regolith dynamics was addressed to emulate continuous-feed regolith reaction processes by measuring leak rates through continuously draining simulant columns. OB-1 lunar highlands regolith simulant was used. Experimental Setup: Regolith simulant columns were constructed using a motorized butterfly valve separating upper acrylic tubes of various diameters from a larger, lower aluminum pipe plenum (See Figure 1). The butterfly valve was cracked open such that gas could freely pass through whereas regolith would bridge and stay suspended as a cohesive plug above in the acrylic portion. These assemblies were loaded into a vacuum chamber, and a compressed dry nitrogen line was routed into the lower plenum. Pressure transducers measured the absolute pressure of the lower plenum, which was compared to absolute chamber pressure to monitor the pressure gradient across the regolith simulant. A precision mass flow controller enabled fine control of plenum pressure. The plenum pressure was quasi-statically increased to set points informed by previous work [1] before shutting off the gas supply to allow the now pressurized gas volume to dissipate through the simulant into the chamber in what was referred to as a ‘leak test.’ In a separate set of tests, the pressure was allowed to quasi-statically build until visual disturbances in the soil were observed via remote camera feeds. Initial leak rate tests were repeated on the disturbed soil to observe changes in leak rates between initial as-poured and post-bubbling soil conditions. This test schedule was applied to simulant columns of three different diameters (approximately 2, 4, and 6 inches) as well as two different heights (around 8 and 16 inches) and was repeated at least three times for each configuration. Plenums were also pressurized while the butterfly valves were opened slightly further to facilitate slow, controlled, constant flowrate draining of the simulant to observe the impact that continuous-feed systems might have on leak rate through the regolith column. Finally, the regolith columns were reset and refilled and static leak rate tests were repeated approximately every decade in ambient pressure from 10e-5 Torr up to ambient conditions to observe the impact of transitioning out of the molecular flow regime on regolith column seal performance. Analysis: Trends with respect to each factor examined were constructed and reported alongside commentary on the most likely responsible physical phenomena. Confidence intervals were applied to the predictive findings of the data by quantifying instrumentation error and accounting for probabilistic impacts of curve fitting the generic exponential function onto pressure decay data. The leak rate is assumed directly proportional to the exponential term coefficient, while the steady-state static pressure gradient is assumed to be the asymptotic limit of each curve fit. Finally, a generic model developed by Ogino et al. [2] and later tuned for ambient testing was re-tuned using vacuum data to estimate leak rates on the lunar surface. Results: Pressure decay rates decreased up to 27-fold under vacuum when compared to ambient pressure, as shown in Figure 2. Simulant column diameter was found to exponentially correlate to both regolith column leak rate and steady-state equilibrium pressure delta. Height was found to be linearly related to leak rate –doubling the regolith column height consistently yielded around a 40% reduction in leak rate. Dynamic regolith draining was found to slightly increase leak rate, although to a lower degree than expected. Conclusion: Because of the transition into molecular gas flow through regolith, vacuum testing is required to properly estimate performance. Regolith columns should be designed as narrow as possible to avoid bridging and minimize leak rate, and as tall as is feasible to both further reduce leak rate and to help prevent bubbling, which has been shown to degrade the quality of the regolith seal. Disrupted soil was found to exhibit higher leak rates than pristine, as-poured soil, indicating the need to consider the impact of recovery from depressurization events. Regolith columns appear equally feasible for both dosed and continuous-feed reactors.

ISRU↗

A continuous mixing model for pdf simulations and its applications to combusting shear flows

The problem of time discontinuity (or jump condition) in the coalescence/dispersion (C/D) mixing model is addressed in this work. A C/D mixing model continuous in time is introduced. With the continuous mixing model, the process of chemical reaction can be fully coupled with mixing. In the case of homogeneous turbulence decay, the new model predicts a pdf very close to a Gaussian distribution, with finite higher moments also close to that of a Gaussian distribution. Results from the continuous mixing model are compared with both experimental data and numerical results from conventional C/D models.

Hsu, A. T.↗

Is There a CME Rate Floor? CME and Magnetic Flux Values for the Last Four Solar Cycle Minima

The recent prolonged activity minimum has led to the question of whether there is a base level of the solar magnetic field evolution that yields a ''floor'' in activity levels and also in the solar wind magnetic field strength. Recently, a flux transport model coupled with magneto-frictional simulations has been used to simulate the continuous magnetic field evolution in the global solar corona for over 15 years, from 1996 to 2012. Flux rope eruptions in the simulations are estimated (Yeates), and the results are in remarkable agreement with the shape of the SOlar Heliospheric Observatory/Large Angle and Spectrometric Coronagraph Experiment coronal mass ejection (CME) rate distribution. The eruption rates at the two recent minima approximate the observed-corrected CME rates, supporting the idea of a base level of solar magnetic activity. In this paper, we address this issue by comparing annual averages of the CME occurrence rates during the last four solar cycle minima with several tracers of the global solar magnetic field. We conclude that CME activity never ceases during a cycle, but maintains a base level of 1 CME every 1.5 to approx. 3 days during minima. We discuss the sources of these CMEs.

Webb, D. F.↗

Simulation Accelerator

Under a NASA SBIR (Small Business Innovative Research) contract, (NAS5-30905), EAI Simulation Associates, Inc., developed a new digital simulation computer, Starlight(tm). With an architecture based on the analog model of computation, Starlight(tm) outperforms all other computers on a wide range of continuous system simulation. This system is used in a variety of applications, including aerospace, automotive, electric power and chemical reactors.

Source record↗

Titan's organic chemistry: Results of simulation experiments

Recent low pressure continuous low plasma discharge simulations of the auroral electron driven organic chemistry in Titan's mesosphere are reviewed. These simulations yielded results in good accord with Voyager observations of gas phase organic species. Optical constants of the brownish solid tholins produced in similar experiments are in good accord with Voyager observations of the Titan haze. Titan tholins are rich in prebiotic organic constituents; the Huygens entry probe may shed light on some of the processes that led to the origin of life on Earth.

Sagan, Carl↗

Spacecraft Fire Safety Predictions using Verified Saffire Model

A model developed using Fire Dynamics Simulator (FDS) that aimed to determine the effect of a fire in a spacecraft was validated by data collected during the Saffire campaign. The model used inlet and outlet temperatures and CO 2 concentrations of the Saffire payload where fire spread was taking place to determine the amount of heat and combustion products that made it into Northrop Grumman’s Cygnus vehicle. The model was then validated using six remote sensors in various places in the vehicle, as well as a far field device (FFD) in the open zenith section that was representative of average vehicle values. The current work focuses on using the model to predict fire safety scenarios. One simulation aimed to determine the fate of HCl, which sticks to surfaces. The model prediction showed that the HCl was removed from the atmosphere rapidly. This compared well against the FFD data in the Saffire VI campaign event where a bottle of 5% HCl was released into the vehicle. An additional simulation where the Environmental Control and Life Support System (ECLSS) was shut off once the FFD reached 5 ppm of HCl showed that HCl stayed in the atmosphere considerably longer. Continuing the simulation with the ECLSS activated and after temperatures returned to their initial conditions, resulted in a rapid removal of HCL similar to that observed in the original HCl release scenario model. Finally, a simulation that used the heat release rate from a lithium-ion battery test to determine the effect it would have on a spacecraft was performed. This simulation used a heat addition rate that is considerably higher than what was determined from the burning of solid fuels in the Saffire campaign and hence produced a non-trivial temperature increase in more locations within the vehicle.

Fire Safety↗

Computational simulation of the creep-rupture process in filamentary composite materials

A computational simulation of the internal damage accumulation which causes the creep-rupture phenomenon in filamentary composite materials is developed. The creep-rupture process involves complex interactions between several damage mechanisms. A statistically-based computational simulation using a time-differencing approach is employed to model these progressive interactions. The finite element method is used to calculate the internal stresses. The fibers are modeled as a series of bar elements which are connected transversely by matrix elements. Flaws are distributed randomly throughout the elements in the model. Load is applied, and the properties of the individual elements are updated at the end of each time step as a function of the stress history. The simulation is continued until failure occurs. Several cases, with different initial flaw dispersions, are run to establish a statistical distribution of the time-to-failure. The calculations are performed on a supercomputer. The simulation results compare favorably with the results of creep-rupture experiments conducted at the Lawrence Livermore National Laboratory.

Slattery, Kerry T.↗

Time response simulation of the 1975 Viking Orbiter digital tape recorder

The objective of the present study was to verify and understand in depth the performance of the speed control (frequency loop) servo of the 1975 Viking Orbiter (VO75) digital tape recorder (DTR). The time response method employed is written in the continuous system simulation language (CSSL) for the Univac 1108 computer system. In order to demonstrate the power and flexibility of the graphic interactive simulation program, four aspects of system dynamics are interactively adjusted to arrive at a number of stable system configurations that have significantly different tape transport and/or summing amplifier gain, larger static/dynamic Coulomb friction, and different system lag than envisioned in the nominal design by linear methods. Work is currently underway to derive a new higher-order DST transfer function and to simulate the servo using state-space variable techniques.

Mukhopadhyay, A. K.↗

Observing and Projecting the Lasting Fate of the Hunga Eruption on Atmospheric Water Vapor and Hydroxyl Radical

On 15th Jan. 2022 the submarine Hunga volcano erupted injecting approximately 0.5 Tg of sulfur dioxide into the stratosphere, but more significantly added 150-170 Tg of water vapor to the stratospheric background (over a 10% perturbation) in a matter of several hours. The sulfur dioxide rapidly converted to sulfate aerosol and along with water vapor, was transported around the Southern Hemisphere sub-tropics into midlatitudes and beyond with some transport into the Northern Hemisphere. With a much longer lifetime than sulfate aerosol, measurable water vapor mass anomalies have persisted with only small losses over more than 2 years since the eruption and are likely to continue above background for the remainder of the decade. Satellite measurements from limb and nadir viewing observing instruments provide the information needed to reasonably initialize the Hunga eruption in the Goddard Earth Observing System (GEOS) model using the “replay” framework coupled to the Global Modeling Initiative (GMI) stratosphere-troposphere chemical mechanism for the recent past and have continued the simulations into the future with the free running chemistry climate model (CCM). Using a number of model ensemble members together with the satellite observations, we quantify how the Hunga eruption is perturbing atmospheric composition and climate and projecting the influences to come as the enhanced water vapor continues in the stratosphere with only very slow removal mechanisms. Modeling suggests that the water rich eruption enhanced stratospheric hydroxyl radiacal (OH) and is supported by the speed of the observed conversion of SO2 into sulfate aerosol. These simulations also suggest a significant reduction in tropospheric OH over the mid-high latitude Southern Hemisphere, which has implications for numerous species that are impacted by this radical. The Hunga eruption provides a useful test of chemistry climate models and an opportunity for observation-based process understanding and in making new connections.

Hunga volcano↗

Evaluation of the usefulness of various simulation technology options for TERPS enhancement

Current approved terminal instrument procedures (TERPS) do not permit the full exploitation of the helicopter's unique flying characteristics. Enhanced TERPS need to be developed for a host of non-standard landing sites and navigation aids. Precision navigation systems such as microwave landing systems (MLS) and the Global Positioning System (GPS) open the possibility of curved paths, steep glide slopes, and decelerating helicopter approaches. This study evaluated the feasibility, benefits, and liabilities of using helicopter cockpit simulators in place of flight testing to develop enhanced TERPS criteria for non-standard flight profiles and navigation equipment. Near-term (2 to 5 year) requirements for conducting simulator studies to verify that they produce suitable data comparable to that obtained from previous flight tests are discussed. The long-term (5 to 10 year) research and development requirements to provide necessary modeling for continued simulator-based testing to develop enhanced TERPS criteria are also outlined.

Phatak, A. V.↗

Projecting the Lasting Fate of the Hunga Tonga-Hunga Ha’apai Eruption on the Stratosphere through Connecting Measurements to Models

On 15th Jan. 2022 the submarine volcano Hunga Tonga-Hunga Ha’apai (HTHH) injected approximately 0.5 Tg of sulfur dioxide into the stratosphere, but more significantly added 150-170 Tg of water vapor to the stratospheric background (over a 10% perturbation) in a matter of several hours. The sulfur dioxide rapidly converted to sulfate aerosol and along with water vapor, was transported around the Southern Hemisphere sub-tropics into midlatitudes with some transport into the Northern Hemisphere. With a much longer lifetime than sulfate aerosol, measurable water vapor mass anomalies have persisted with only small losses over the past almost 2 years and are likely to continue above background for the remainder of the decade. Satellite measurements from limb and nadir viewing observing instruments provide the information needed to reasonably initialize the HTHH eruption in the Goddard Earth Observing System (GEOS) model using the “replay” framework coupled to the Global Modeling Initiative (GMI) stratosphere-troposphere chemical mechanism for the recent past and continue the simulations into the future with the free running chemistry climate model (CCM). Using a number of model ensemble members together with the satellite observations, we quantify how the HTHH eruption is perturbing stratospheric composition and climate and projecting the influences to come as the enhanced water vapor continues in the stratosphere with only very slow removal mechanisms. HTHH eruption provides a useful test of chemistry climate models and an opportunity for observation-based process understanding, which we will highlight.

Hunga Tonga-Hunga Ha’apai↗

Projecting the Lasting Fate of the Hunga Tonga-Hunga Ha’apai Eruption on the Stratosphere through Connecting Measurements to Models

On 15th Jan. 2022 the submarine volcano Hunga Tonga-Hunga Ha’apai (HTHH) injected approximately 0.5 Tg of sulfur dioxide into the stratosphere, but more significantly added 150-170 Tg of water vapor to the stratospheric background (over a 10% perturbation) in a matter of several hours. The sulfur dioxide rapidly converted to sulfate aerosol and along with water vapor, was transported around the Southern Hemisphere sub-tropics into midlatitudes with some transport into the Northern Hemisphere. With a much longer lifetime than sulfate aerosol, measurable water vapor anomalies are likely to persist for the remainder of the decade. Satellite measurements from limb and nadir viewing observing instruments provide the information needed to reasonably initialize the HTHH eruption in the Goddard Earth Observing System (GEOS) model using the “replay” framework coupled to the Global Modeling Initiative (GMI) stratosphere-troposphere chemical mechanism for the recent past and continue the simulations into the future with the free running chemistry climate model (CCM). Using a number of model ensemble members together with the satellite observations, we are beginning to quantify how the HTHH eruption is perturbing stratospheric composition and climate and projecting the influences to come as the enhanced water vapor continues to spread globally with only very slow removal mechanisms. We will also discuss some of the future measurement needs to understand how the atmosphere is responding to events like the HTHH eruption, large wildfires, and a changing climate.

volcano↗

Simulations of Evaporating Multicomponent Fuel Drops

A paper presents additional information on the subject matter of Model of Mixing Layer With Multicomponent Evaporating Drops (NPO-30505), NASA Tech Briefs, Vol. 28, No. 3 (March 2004), page 55. To recapitulate: A mathematical model of a three-dimensional mixing layer laden with evaporating fuel drops composed of many chemical species has been derived. The model is used to perform direct numerical simulations in continuing studies directed toward understanding the behaviors of sprays of liquid petroleum fuels in furnaces, industrial combustors, and engines. The model includes governing equations formulated in an Eulerian and a Lagrangian reference frame for the gas and drops, respectively, and incorporates a concept of continuous thermodynamics, according to which the chemical composition of a fuel is described by use of a distribution function. In this investigation, the distribution function depends solely on the species molar weight. The present paper reiterates the description of the model and discusses further in-depth analysis of the previous results as well as results of additional numerical simulations assessing the effect of the mass loading. The paper reiterates the conclusions reported in the cited previous article, and states some new conclusions. Some new conclusions are: 1. The slower evaporation and the evaporation/ condensation process for multicomponent-fuel drops resulted in a reduced drop-size polydispersity compared to their single-component counterpart. 2. The inhomogeneity in the spatial distribution of the species in the layer increases with the initial mass loading. 3. As evaporation becomes faster, the assumed invariant form of the molecular- weight distribution during evaporation becomes inaccurate.

Bellan, Josette↗

Random Telegraph Signal Amplitudes in Sub 100 nm (Decanano) MOSFETs: A 3D 'Atomistic' Simulation Study

In this paper we use 3D simulations to study the amplitudes of random telegraph signals (RTS) associated with the trapping of a single carrier in interface states in the channel of sub 100 nm (decanano) MOSFETs. Both simulations using continuous doping charge and random discrete dopants in the active region of the MOSFETs are presented. We have studied the dependence of the RTS amplitudes on the position of the trapped charge in the channel and on the device design parameters. We have observed a significant increase in the maximum RTS amplitude when discrete random dopants are employed in the simulations.

Asenov, Asen↗

Aerojet - Attitude Control Engines

All the engines were both qualification and acceptance tested at Marquardt s facilities. After we won the Apollo Program contract, we went off and built two vacuum test facilities, which simulated altitude continuous firing for as long as we wanted to run an engine. They would run days and days with the same capability we had on steam ejection. We did all of the testing in both for the qualification and the acceptance test. One of them was a large ball, which was an eighteen-foot diameter sphere, evacuated again with a big steam ejector system that could be used for system testing; that s where we did the Lunar Excursion Module testing. We put the whole cluster in there and tested the entire cluster at the simulated altitude conditions. The lowest altitude we tested at - typically an acceptance test - was 105,000 feet simulated altitude. The big ball - because people were interested in what they called goop formation, which is an unburned hydrazine product migrating to cold surfaces on different parts of spacecraft - was built to address those kinds of issues. We ran long-life tests in a simulated space environment with the entire inside of the test cell around the test article, liquid nitrogen cooled, so it could act as getter for any of the exhaust products. That particular facility could pull down to about 350,000 feet (atmosphere) equivalent altitude, which was pushing pretty close to the thermodynamic triple point of the MMH. It was a good test facility. Those facilities are no longer there. When the guys at Marquardt sold the company to what eventually became part of Aerojet, all those test facilities were cut off at the roots. I think they have a movie studio there at this point. That part of it is truly not recoverable, but it did some excellent high-altitude, space-equivalent testing at the time. Surprisingly, we had very few problems while testing in the San Fernando Valley. In the early 1960s, nobody had ever seen dinitrogen tetroxide (N2O4), so that wasn't too big a deal. We really did only make small, red clouds. In all the hundreds of thousands of tests and probably well over one million firings that I was around that place for, in all that thirty-something years, we had a total of one serious injury associated with rocket engine testing and propellants. Because we were trying to figure out what propellants would really be good, we tried all of the fun stuff like the carbon tetrafluoride, chlorine pentafluoride, and pure fluorine. The materials knowledge wasn't all that great at the time. On one test, the fluorine we had didn't react well with the copper they were using for tubing, and it managed to cause another unscheduled disassembly of the facility. It was very serious. It's like one of those Korean War stories. The technician happened to be walking past the test facility when it decided to blow itself up. A piece of copper tubing pierced one cheek and came out the other. That was the only serious accident in all of the engines handled in all those years. Now, we did have a problem with the EPA later because they figured out what the brown clouds were about. We built a whole bunch of exhaust mitigation scrubbers to take care of engine testing in the daytime. In general, we operated the big shuttle (RCS) engine, the 870- pounder at nominal conditions; they scrubbed the effluents pretty well. If you operated that same 870-pound force engine at a level where you get a lot of excess oxidizer, yeah, there s a brown cloud. But, you know, it doesn't show up well in the dark. They did do some of that. But, that s gone; it was addressed one way or another. RELEASED -

Pfeifer, Gerald R.↗

Extraction-Separation Performance and Dynamic Modeling of Orion Test Vehicles with Adams Simulation: 3rd Edition

NASA's Orion Capsule Parachute Assembly System (CPAS) Project is now in the qualification phase of testing, and the Adams simulation has continued to evolve to model the complex dynamics experienced during the test article extraction and separation phases of flight. The ability to initiate tests near the upper altitude limit of the Orion parachute deployment envelope requires extractions from the aircraft at 35,000 ft-MSL. Engineering development phase testing of the Parachute Test Vehicle (PTV) carried by the Carriage Platform Separation System (CPSS) at altitude resulted in test support equipment hardware failures due to increased energy caused by higher true airspeeds. As a result, hardware modifications became a necessity requiring ground static testing of the textile components to be conducted and a new ground dynamic test of the extraction system to be devised. Force-displacement curves from static tests were incorporated into the Adams simulations, allowing prediction of loads, velocities and margins encountered during both flight and ground dynamic tests. The Adams simulation was then further refined by fine tuning the damping terms to match the peak loads recorded in the ground dynamic tests. The failure observed in flight testing was successfully replicated in ground testing and true safety margins of the textile components were revealed. A multi-loop energy modulator was then incorporated into the system level Adams simulation model and the effect on improving test margins be properly evaluated leading to high confidence ground verification testing of the final design solution.

Varela, Jose G.↗

Large Eddy Simulations of Upper-Ocean Turbulence Across the Equatorial Pacific Cold Tongue

Turbulence in the equatorial Pacific cold tongue plays multiple roles in the sea-surface temperature budget. However, observations of turbulence are limited to a handful of field experiments lasting from a few days to one month at 0 N , 140 W, and the key turbulent fluxes can only be inferred. Although explicit simulations of turbulence resolve these fluxes, the required large eddy simulations (LES) are costly and thus also limited to a few weeks. A two-fold hypothesis motivates this contribution to the PUMP pre-field modelling experiments in support of TPOS: 1) that there exist useful relationships between the surface wind, wave, and buoyancy forcing, oceanic shear and stratification, and turbulent mixing, but 2) these relationships differ between regions of equatorial dynamics (f~0) and higher latitudes, such that the state space is insufficiently sampled to understand these relationships and represent them in ocean general circulation models (OGCM). To address the lack of observations, we simulated 35 continuous days of upper ocean turbulence using LES during October-November 1985 at sites in two regions (70 days in total) of the cold tongue: 0 N, 140 W and 3 N, 140 W. The model reproduces many features of the observed turbulence at 0,140W, including the “deep-cycle” observed by Gregg et al. (1985) Nature and the turbulent pulses every few hours during the night and in the early morning. Furthermore, the results at 3 N support the hypothesis advanced by Cherian et al. (2021) JPO that strong, but intermittent deep-cycle turbulence is observed to the north of the equator in the presence of strong shear associated with Tropical Instability Waves. Comparisons with the K-profile parameterization (KPP) scheme show that additional tuning of the KPP parameters can reduce differences between the turbulent fluxes produced by KPP and LES at both sites. The results will suggest modifications to OGCMs and already emphasize the need for a more extensive measurements of vertical profiles of shear, stratification and turbulent mixing to reveal the spatio-temporal structure of turbulence and how it relates to forcing, shear and stratification across the equatorial Pacific Cold tongue.

Large Eddy Simulations↗

Infrared Spectral Observations While Drilling into a Frozen Lunar Simulant

Past and continuing observations indicate an enrichment of volatile materials in lunar polar regions. While these volatiles may be located near the surface, access to them will likely require subsurface sampling, during which it is desirable to monitor the volatile content. In a simulation of such activities, a multilayer lunar simulant was prepared with differing water content, and placed inside a thermal vacuum chamber at Glenn Research Center (GRC). The soil profile was cooled using liquid nitrogen. In addition to the soil, a drill and infrared (IR) spectrometer (~1600-3400 nm) were also located in the GRC chamber. We report the spectral observations obtained during a sequence where the drill was repeatedly inserted and extracted, to different depths, at the same location. We observe an overall increase in the spectral signature of water ice over the duration of the test. Additionally, we observe variations in the water ice spectral signature as the drill encounters different layers.

volatile content↗