Search NASA⌕ Search

SEARCH · Search NASA

Results for “crack resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Control of High-Temperature Static and Transient Thermomechanical Behavior of SiMo Ductile Iron by Al Alloying

Abstract Silicon and molybdenum ( SiMo ) ductile iron is commonly used for exhaust manifolds because these components experience thermal cycling in oxidizing environment, which requires resistance to fatigue during transient thermomechanical loads. Previous studies have demonstrated that alloying elements, such as Al , to SiMo ductile iron reduces the amount of surface degradation during static high-temperature exposure. However, deterioration of sphericity of the graphite nodules and a decrease in ductility could affect the tendency of cracking during thermal cycling. In this article, the effect of Al alloying on static and transient thermomechanical behavior of SiMo ductile iron was investigated to optimize the amount of Al alloying. A thermodynamic approach was used to confirm the effect of the Al alloying on the phase transformations in two SiMo cast irons, alloyed by 1.8% Al and 3% Al . These two alloys were cast in a laboratory along with the baseline SiMo ductile iron. Several experimental methods were used to evaluate the dimensional stability, physical properties, static oxidation, and failure resistance during constrained thermal cycling testing to compare their high-temperature capability. Experimental results verified that Al alloying increases the temperature range and decreases volume change during eutectoid transformation, which together with enhancement of oxidation protection improved the dimensional stability. Thermocycling tests showed that the number of cycles to failure depends on the amount of Al alloying and the applied high-temperature exposure during each cycle. SEM/EDX, high-resolution TEM and µCT analysis were used to verify the mechanism resulting from the Al alloying protection. It was shown that an optimal level of Al alloying for balancing oxidation and thermal cracking resistance depends on thermomechanical conditions of application.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Pitting behavior of friction stir repair-welded 304L stainless steel in 3.5% NaCl solution at room temperature: role of grain and defect structures

Stainless steel (SS) canisters used for storing spent nuclear waste are prone to chloride-induced stress corrosion cracking. Friction stir welding (FSW), being a low heat input process, can be used for repair welding of these canisters. In this study, an artificial crack was introduced on the 304L SS coupons by an electric discharge machining process. The artificial crack was repair-welded by FSW by maintaining the tool temperature a constant at two levels (725 and 825 °C). Friction stirring significantly reduced the grain size of the stirred zone (SZ) from about 47 to 2–4 μm. The fraction of low-angle grain boundaries increased in the SZ from 2 to 37–43%. Here, on the other hand, the fraction of special grain boundaries (Σ3 and Σ9) that was ~ 50% in the base metal reduced to < 10% in the SZ. During friction stirring, the oxide layer of artificial crack was broken and aligned to form a spiral defect called lazy-S structure. All these microstructural changes affected the corrosion behavior of the FSW specimens when tested in 3.5% NaCl at room temperature using cyclic polarization, chronoamperometry, and electrochemical impedance spectroscopy. The FSW specimens showed lower polarization resistance and lower transpassive potential than those of the base metal specimens. However, the pitting protection potentials of the FSW specimens were higher than that of the base metal. The pitting behavior of the FSW specimens was influenced more by the preferential attack on the lazy-S region than by passive film breakdown. The flat band potentials of the passive film formed on the FSW specimens were more positive than that of base metal. The charge carrier density of passive film formed on the FSW specimens was higher than that of the base metal. The higher fraction of low-angle grain boundaries present in the FSW specimens could supply more number of misorientation dislocations at the metal/film interface which could form anion vacancies by a climb process leading to formation of oxide at these locations without stressing the substrate. Therefore, low-angle boundaries are considered helpful for formation of stress-free passive films that will be highly stable and enhance both pitting and stress corrosion cracking resistance.

Dry storage canister↗
DOE OSTI2026

Extended Rice–Thomson analysis and atomistic simulations revealing grain boundary effects on fracture in refractory high-entropy alloys

Significance This work serves to extend the fundamental ductile vs. brittle fracture theory, specifically the Rice–Thomson criterion, by introducing a grain boundary ahead of an initiating crack which propagates at an oblique angle to impinge the boundary. Atomistic fracture simulations on two refractory complex concentrated alloys, the brittle NbMoTaW and the ductile Nb 45 Ta 25 Ti 15 Hf 15 , demonstrate qualitative correspondence with the extended Rice–Thomson criterion and experimental observations. Abstract Understanding how grain boundaries mediate fracture remains a critical challenge in designing ductile, high-performance refractory alloys. Here, we extend the Rice–Thomson criterion to account for the angle between cracks and the impinging grain boundaries (GBs), capturing the competition between intergranular fracture and dislocation-mediated plasticity. Using machine learning interatomic potentials, we performed molecular statics simulations to probe fracture mechanisms in nanocrystalline NbMoTaW and Nb 45 Ta 25 Ti 15 Hf 15 , each with two different grain sizes, revealing trends consistent with experimental observations and the extended Rice model. Comparison with averaged R-curves for bulk samples demonstrates that GBs enhance ductility in Nb 45 Ta 25 Ti 15 Hf 15 in both grain sizes investigated. In contrast, GBs only locally improve fracture resistance in NbMoTaW when cracks are temporarily pinned at GBs inclined at high angles from the crack, but generally promote brittle intergranular fracture. These contrasting behaviors are attributed to differences in GB cohesion, reflecting clear alloying trends that align with ab-initio calculations and trends observed experimentally. Our results bridge classical fracture theory, atomistic simulations, and experimental observations, providing a comprehensive understanding of the fracture mechanisms in nanocrystalline refractory complex concentrated alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Deformation band corrosion as a result of applied stress and cold-work in 304 stainless steel in simulated pressurized water reactor primary water conditions

Stainless steels like 304SS are commonly used in pressurized water reactor primary water environments due to their excellent resistance to stress corrosion cracking (SCC). However, SCC susceptibility has been observed in cold-worked 304SS. Cold-rolling introduces a high density of defects, such as deformation bands or dislocations, into the microstructure; applied stress, even if macroscopically below the yield stress, can result in regions with high localized stresses. Cold-worked and non-cold-worked samples were exposed to 360 °C simulated PWR primary water for 1500 h with and without active loading. Corrosion susceptibility of dislocations and deformation bands induced by cold-rolling and/or applied stress was studied using high-resolution (analytical) transmission electron microscopy. Deformation bands were generated in all specimens examined in the study. Penetrative oxidation was observed in some deformation bands in each specimen. The depth of penetrative deformation band oxidation frequently exceeded the depth of grain boundary oxidation in all specimens. However, deformation band oxides generally were narrowly confined to the deformation band plane. Highly Ni-rich regions were observed beyond all oxidation fronts. Surface oxides were thicker in the specimens exposed under active loading. In conclusion, the implications of these findings at surfaces for deformation bands intersecting stress corrosion crack paths are discussed.

EFTEM↗
DOE OSTI2022

Estimation of pipe failure frequencies in the absence of operational experience data: A pilot study

Probabilistic failure metrics such as leak frequency and rupture frequency are commonly used to characterize piping reliability. The methodologies for calculating the failure metrics rely on a complex set of input parameters. Operating experience data and experimental data play an important role in informing the different input parameters. The paper describes results and conclusions of a coordinated research project to benchmark three different reliability models using a four-step procedure: reference case definition of relevance to advanced reactor designs, input parameter calibration, validation of results, and application of different methodologies upon completion of the calibration and validation steps. The reference case is a weld consisting of nickel-base alloy 152/52 and located within a primary pressure boundary of an advanced reactor. This alloy is a class of structural materials known to be highly resistant to stress corrosion cracking. Synergies between the different methods are noted and the importance of a multi-disciplinary approach to input parameter development is underscored. A key conclusion is that the three methods are equally suitable for estimating failure frequencies. In any specific application, a selection of the most practical or effective computational tool can be considered. The comparison of alternative models confirms and helps to gain confidence in the computed failure frequency estimates. The study was part of a coordinated research project organized by the International Atomic Energy Agency.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Distinct Mechanism of Anti-Corrosion and Swelling-Adhesion Modeling of Low-Dimensional Nylon-Fluoropolymer Composite Coatings

Compared to other polymers, composite coatings with fluoropolymers as the matrix have attracted considerable interest due to their mechanical performance, chemical stability, and low surface energy. Herein, we present an anticorrosion mechanism of fluoropolymer composite coatings achieved by dispersing varying amounts of polyamide 12 (PA-12) particles over a poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) matrix. The choice of PVDF-HFP as a coating matrix was driven by its superior processability and mechanical properties over Teflon, while PA-12 afforded swelling capacity, preventing electrolyte permeation, and inhibiting matrix stress crack propagation. The corrosion resistance of the coatings was assessed mainly by potentiodynamic polarization and impedance measurements while being immersed in a NaCl solution. Our electrochemical measurement findings showed that 0.75% w/w PA-12 in the PVDF-HFP matrix significantly enhanced corrosion protection even after 21 days of immersion. Microscopy, dielectric spectroscopy, surface analysis, and mechanical testing (American Society for Testing and Materials standards) corroborated the results. PVDF-HFP coatings containing a minimum percolation threshold of 0.75 wt % PA-12 with 1 mil thickness on mild steel exhibited a remarkable increase in resistance and film adhesion, and a notable corrosion rate decrease. Finite element analysis simulation with a bilinear traction-separation law confirmed the swelling mechanism and adhesion behavior. Finally, this study highlights the potential of nylon particle dispersion in PVDF-HFP matrices as a practical approach to developing advanced anticorrosion coatings with promising practical applications in various industries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Structure-mechanical properties correlation in bulk LiPON glass produced by nitridation of metaphosphate melts

The glassy solid electrolyte Lithium phosphorous oxynitride (LiPON) has been widely researched in thin film solid state battery format due to its outstanding stability when cycled against lithium. In addition, recent reports show thin film LiPON having interesting mechanical behaviors, especially its ability to resist micro-scale cracking via densification and shear flow. Here, in the present study, we have produced bulk LiPON glasses with varying nitrogen contents by ammonolysis of LiPO 3 melts. The resulting compositions were determined to be LiPO 3-3z/2 N z , where 0 ≤ z ≤ 0.75, and the z value of 0.75 is among the highest ever reported for this series of LiPON glasses. The short-range order structures of the different resulting compositions were characterized by infrared, Raman, 31 P magic angle spinning nuclear magnetic resonance, and X-ray photoelectron spectroscopies. Instrumented nano-indentation was used to measure mechanical properties. It was observed that similar to previous studies, both trigonally coordinated (N t ) and doubly bonded (N d ) N co-exist in the glasses in about the same amounts for z ≤ 0.36, the limit of N content in most previous studies. For glasses with z > 0.36, it was found that the fraction of the N t increased significantly while the fraction of N d correspondingly decreased. The incorporation of nitrogen increased both the elastic modulus and hardness of the glass by approximately a factor of 1.5 when N/P ratio reaches 0.75. At the same time, an apparent embrittlement of the glass was observed due to nitridation, which was revealed by nanoindentation with an extra sharp nanoindenter tip.

25 ENERGY STORAGE↗
DOE OSTI2022

Effect of Applied Stress on the Selective Oxidation of Alloy 600 Exposed to PWR Primary Water and Rhines Pack Environments

A mechanistic understanding of corrosion and oxidation processes is crucial to ensure long-term resistance to stress corrosion cracking of Ni-base structural alloys in pressurized water reactor (PWR) primary and secondary systems. Aqueous corrosion of Ni-base alloys under PWR primary water conditions was previously compared to gaseous oxidation with comparable oxygen potentials. However, those studies considered only stress-free conditions, which removes a critical parameter for understanding stress corrosion behaviors. A significant knowledge gap exists for the role of applied stresses on selective internal oxidation in gaseous environments. A micro-4-point-bend jig was designed to facilitate stress in a Rhines Pack set-up. Selective oxidation at different stress and strain conditions was investigated in a series of Rhines Pack experiments for Alloy 600. Focused ion beam milling enabled the extraction of site-specific specimens containing selected high-energy grain boundaries from tensile and compressive stress regions. Analytical transmission electron microscopy was employed to analyze the microstructure and chemical composition of the resulting oxides. Protective surface oxide films and selective intergranular oxides were observed at different conditions. The implications of these fundamental differences are discussed relative to intergranular attack and stress corrosion cracking mechanisms in PWR primary water.

stress, 4-point-bend, selective oxidation, Alloy 6↗
DOE OSTI2024

Crack mitigation in additively manufactured AlCrFe 2 Ni 2 high-entropy alloys through engineering phase transformation pathway

The far-from-equilibrium solidification during additive manufacturing often creates large residual stresses that induce solid-state cracking. Here we present a strategy to suppress solid-state cracking in an additively manufactured AlCrFe 2 Ni 2 high-entropy alloy via engineering phase transformation pathway. We investigate the solidification microstructures formed during laser powder-bed fusion and directed energy deposition, encompassing a broad range of cooling rates. At high cooling rates (10 4 –10 6 K/s), we observe a single-phase BCC/B2 microstructure that is susceptible to solid-state cracking. At low cooling rates (10 2 –10 4 K/s), FCC phase precipitates out from the BCC/B2 matrix, resulting in enhanced ductility (~10 %) and resistance to solid-state cracking. Site-specific residual stress/strain analysis reveals that the ductile FCC phase can largely accommodate residual stresses, a feature which helps relieve residual strains within the BCC/B2 phase to prevent cracking. Our work underscores the value of exploiting the toolbox of phase transformation pathway engineering for material design during additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Impact of Laboratory-Accelerated Aging Methods to Study Alkali–Silica Reaction and Reinforcement Corrosion on the Properties of Concrete

This study focuses on two separate investigations of the main aging mechanisms: alkali–silica reactivity (ASR) and the corrosion of reinforcing steel (rebar) concrete, both of which may result in a premature failure to meet the serviceability or strength requirements of a concrete structure. However, these processes occur very slowly, spanning decades. The impact of direct chemical additives to fresh concrete to accelerate ASR and the corrosion of reinforcing steel on the fresh and hardened properties of the ensuing material are investigated to inform the potential use of chemicals in large-scale studies. The deterioration of reinforced concrete (RC) is determined by means of expansion, cracking, bulk diffusivity and surface resistivity measurements, and compressive, split tensile and flexural strength tests. The results indicate that the addition of sodium hydroxide and calcium chloride can effectively accelerate the crack formation and propagation in concrete due to ASR and the corrosion of rebar, respectively. The ASR-induced cracks maintained a constant crack width from 0.05 mm to 0.1 mm over the measurement period regardless of the intensity of aging acceleration. Adding 4% chloride by weight of cement for accelerating rebar corrosion resulted in an average crack that was 82% larger than in the case of ASR accelerated with the addition of sodium hydroxide. The addition of alkali resulted in an increase in early-age (7-day) strength. At a total alkali loading of 2.98 kg/m3, 3.84 kg/m3 and 5.57 kg/m3, the 28-day compressive strength of concrete decreased by 3%, 10% and 24%, respectively. Similarly, a higher early-age strength and a lower later-age strength was observed for the concrete in the presence of corrosive calcium chloride. The results from this research are expected to inform future studies on the long-term performance of RC structures under accelerated ASR and corrosion.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Influence of supplementary cementitious materials on microstructure and transport properties of spacer-concrete interface

Reinforcement spacers are a critical component of concrete structures. Their presence affects microstructure and transport properties of concrete cover though this is not widely appreciated. This paper presents the first study to determine whether the negative effects of spacers can be mitigated through the use of supplementary cementitious materials such as silica fume, fly ash and blast-furnace slag. Concrete samples (>200) with different spacers, binders, curing and drying regimes were prepared and tested for diffusion, permeation, absorption, electrical conductivity, carbonation and microstructure. It was found that spacers increase all transport properties, the extent depending on type of spacer, drying regime and transport mechanism. The spacer-concrete interface is weak, porous and micro-cracked, and this lowers the resistance of concrete to ingress of aggressive agents. The beneficial effects of SCMs (strength enhancement and densification) and prolonged curing (120-day) are insufficient to overcome the negative effects of spacers. Implications for durability are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Separate-Effects Tests for Studying Temperature-Gradient-Driven Cracking in UO 2 Pellets

We report a variety of normal operation and accident scenarios can generate thermal stresses large enough to cause cracking in light-water reactor (LWR) fuel pellets. Cracking of fuel pellets can lead to reduced heat removal, higher centerline temperatures, and localized stress in cladding, all of which impact fuel performance. It is important to experimentally characterize the thermal and mechanical behavior in the pellet before and after cracking to improve cracking models in fuel performance codes. However, in-reactor observation and measurement of cracking is very challenging due to the harsh environment and logistics. Recently, an experimental pellet cracking test stand was developed for separate effects testing of normal operations and accident temperature conditions, using thermal imaging to capture the pellet surface temperature for evaluation of thermal stresses and optical imaging to capture the evolution of cracking in real time. Experiments were performed using depleted uranium dioxide (UO 2 ) pellets, which are useful for collecting data valuable for development and validation of cracking models. A combination of induction and resistance heating was used to create an average temperature gradient of 236°C/cm and 193°C/cm before and after cracking respectively. Characterization of the pellets were done before as well as after cracking. The cracking patterns are somewhat different than those expected in a typical reactor because of the differences in thermal conditions and pellet microstructure. However, if the actual conditions of these experiments are reproduced in computational models, these out-of-pile tests on UO 2 pellets provide relevant data for modeling purposes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Understanding the influence of boron in additively manufactured GammaPrint®-700 CoNi-based superalloy

Boron is commonly added to superalloys in small amounts to enhance creep resistance, but can lead to cracking at high concentrations, especially during the additive manufacturing process. Two variants of CoNi-based GammaPrint®-700 superalloy with different B contents (0.08 at% vs 0.16 at%) were printed via laser powder bed fusion (LPBF) with the same printing parameters, with only the high B alloy exhibiting solidification cracking. Atom probe tomography (APT) revealed stronger segregation behaviors in the high B alloy compared to the low B alloy at both the inter-dendritic regions and grain boundaries (GBs). The segregation behavior at inter-dendritic regions was well captured with Scheil simulation and can correlate with the existing cracking susceptibility index (CSI) on cracking tendencies, although high angle GBs are where cracking occurs according to electron backscatter diffraction (EBSD) measurements. Additionally, the extent of GB segregation was compared between the high B and low B alloy. Higher B additions led to significantly more GB B segregation in the high B alloy compared to the low B alloy. Further, for the high B alloy, the cracked region of one GB exhibited higher levels of B compared to the uncracked region of the same GB. However, much higher B contents were also found in two other uncracked GBs in the high B alloy, which demonstrates that higher GB B concentrations are not fully responsible for the cracking. A much larger variance in GB B segregation content was found in the high B alloy compared to the low B alloy. These phenomena were explained with a solidification model with the GB segregation content expressed explicitly by a modified Langmuir-McLean equation. This model linked the GB segregation content with solidification undercooling, which can be used as quantitative cracking criteria for future builds.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Dynamic oxidation of (Mn,Co) 3 O 4 -Coated interconnects for solid oxide electrolysis cells

Solid oxide electrolysis cell stacks are expected to experience dynamic conditions when using renewable electricity derived from wind or solar power. To address this scenario, (Mn,Co) 3 O 4 (MCO)-coated Crofer 22 APU interconnect coupons are subjected to thermal cycling, and intermittent current density, with gas compositions relevant to high-temperature electrolysis (elevated steam:hydrogen ratio and oxygen content). Defects are also intentionally introduced in the MCO coating, to assess whether the difference in oxidation properties of the adjacent coated and uncoated (defective) surfaces causes sufficient stress to damage the protective oxide scale. Specimens with defects are subjected to oxidation for 1000 h at 800 °C, or thermal cycling. Before thermal cycling, some specimens are pre-oxidized to create a thick oxide scale to mimic the scale thickness expected after ~30 kh operation. In all cases, the coating and oxide scale remain well adhered with no cracking observed. Area-specific resistance (ASR) is monitored in both single-atmosphere and dual-atmosphere conditions, and the ASR is stable and is not impacted by dynamic cycling of the current density. Finally, this work provides confidence that the MCO coated interconnect will function as needed in dynamic operation conditions, even with coating defects.

08 HYDROGEN↗
DOE OSTI2023

Operando neutron diffraction reveals mechanisms for controlled strain evolution in 3D printing

Abstract Residual stresses affect the performance and reliability of most manufactured goods and are prevalent in casting, welding, and additive manufacturing (AM, 3D printing). Residual stresses are associated with plastic strain gradients accrued due to transient thermal stress. Complex thermal conditions in AM produce similarly complex residual stress patterns. However, measuring real-time effects of processing on stress evolution is not possible with conventional techniques. Here we use operando neutron diffraction to characterize transient phase transformations and lattice strain evolution during AM of a low-temperature transformation steel. Combining diffraction, infrared and simulation data reveals that elastic and plastic strain distributions are controlled by motion of the face-centered cubic and body-centered cubic phase boundary. Our results provide a new pathway to design residual stress states and property distributions within additively manufactured components. These findings will enable control of residual stress distributions for advantages such as improved fatigue life or resistance to stress-corrosion cracking.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tritium Aging Effects on Fracture Toughness of Stainless Steel Weldments

The long-term embrittlement effects of tritium and decay helium on the structural properties of stainless steels have been studied for years at Savannah River to provide required data for establishing safe operating conditions and lifetimes of pressure vessels used to contain tritium gas. In this study, the fracture toughness properties of the longest-aged tritium-precharged stainless-steel base metals and weldments tested at Savannah River were measured and compared to earlier results. The fracture toughness values were the lowest recorded here for tritium-exposed stainless steel. As-forged and as-welded specimens were thermally precharging with tritium gas at 34.5 MPa and 623 K, then aged for up to 17 years to buildin decay helium prior to testing. ASTM J-Integral fracture mechanics analyses, transmission electron microscopy (TEM), and small angle neutron scattering (SANS) examinations were conducted to characterize the effects of tritium and its radioactive decay product, helium-3. Results show that the fracture toughness values were reduced to less than 2-4% of the as-forged values for specimens with more than 1300 appm helium from tritium decay. The trend of decreasing fracture toughness values with increasing helium content was consistent with earlier observations, and the data show that Type 304L stainless steel is more resistant to tritium-induced cracking than Type 21-6-9 stainless at similar decay helium levels. The fracture toughness properties of long-aged weldments were also affected, but the reductions were not as severe over time because weldments did not retain as much tritium as did the base metals. TEM observations were used to characterize the effects of decay helium bubbles on the deformation substructures, but nanometer-sized helium bubbles were not easily resolved because of high dislocation densities within the forged microstructures. SANS results are presented that suggest the technique can provide information on decay helium bubble size, spacing, and distribution in these steels.

36 MATERIALS SCIENCE↗
DOE OSTI2020

ALLOY SELECTION AND C-276 CODE DESIGN VALUE EXTENSION FOR ADVANCED MOLTEN SALT TECHNOLOGY TEST FACILITIES EXPERIMENTATION

Molten halide salts are being considered as working fluids for nuclear and concentrated solar power applications. High temperature molten fluoride and chloride salts are known to preferentially attack and deplete Cr in alloys, which leads to the use of high-Ni lower-Cr alloys in test facilities for advanced Molten Salt Technology. Alloys 600 and C-276 are two commercially available Ni alloys that have moderate Cr contents and are qualified to the maximum temperature of 649°C and 677°C (1,200°F and 1,251°F), respectively, in the Boiler and Pressure Vessel Code. Both alloys have good corrosion resistance to acids, are resistant to stress-corrosion cracking, and have long track records of use in the chemical industry. Comparatively, Alloy C-276 has a similar Cr content but much higher allowable stresses for temperatures greater than 600°C (1,112°F). Therefore, it has been considered as a structural material for test facilities that require operations at 700°C (1,292°F) or greater to develop high-temperature Molten Salt Technology. To meet the requirements, the current code design values were extended based on some experimental data. Analysis showed that above current Codified maximum temperature, strength of the alloy is mainly controlled by creep rupture life under the average stress, although the Sc creep rate criterion is close to the Favg.Savg rupture criterion. This paper presents the intended test facilities and the design requirements, alloy selection considerations, literature review, data analysis, and proposed allowable stress extension based on some creep test data for C-276 at temperatures greater than 677°C (1,251°F). Further research activities are also briefly mentioned.

Ren, Weiju↗