Search NASA⌕ Search

SEARCH · Search NASA

Results for “creep life”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Microstructure, electrical resistivity, and tensile properties of neutron-irradiated Cu–Cr–Nb–Zr

High strength, high conductivity copper alloys that can resist creep at high temperatures are one of the primary candidates for efficient heat exchangers in fusion reactors. Cu–Cr–Nb–Zr (CCNZ) alloys, which were designed to improve the strength and creep life of ITER Cu–Cr–Zr (CCZ) reference alloys, have been found to have comparable electrical conductivity and tensile properties to CCZ alloys. The measured creep rupture times for these improved alloys is about ten times higher than the ITER reference alloys at 90–125 MPa at 500 °C. However, the effects of neutron irradiation on these alloys, and the ensuing material properties, have not been studied; thus, their utility in a fusion reactor environment is not well understood. This study characterizes the room temperature mechanical and electrical properties of a neutron-irradiated CCNZ alloy and compares them to a neutron-irradiated ITER reference heat sink CCZ alloy. Tensile specimens were neutron irradiated in the High Flux Isotope Reactor (HFIR) to 5 dpa between 250 °C and 325 °C. Post-irradiation characterization included electrical resistivity measurements, hardness, and tensile tests. Microstructural evaluation used scanning electron microscopy, energy dispersive x-ray spectroscopy, and atom probe tomography to characterize the irradiation-produced changes in the microstructure and investigate the mechanistic processes leading to post-irradiation properties. Transmutation calculations were validated with composition measurements from atom probe data and used to calculate contributions to the increased electrical resistivity measured after irradiation. Comparisons with CCZ alloys in the same irradiation heat found that the post-irradiated CCNZ and CCZ alloys had comparable electrical resistivity. Although CCNZ alloys suffered more irradiation hardening than CCZ, the overall tensile behavior deviated very little from non-irradiated values in the temperature range studied.

36 MATERIALS SCIENCE↗
NASA NTRS2014

Time-Dependent Behavior of High-Strength Kevlar and Vectran Webbing

High-strength Kevlar and Vectran webbings are currently being used by both NASA and industry as the primary load-bearing structure in inflatable space habitation modules. The time-dependent behavior of high-strength webbing architectures is a vital area of research that is providing critical material data to guide a more robust design process for this class of structures. This paper details the results of a series of time-dependent tests on 1-inch wide webbing including an initial set of comparative tests between specimens that underwent realtime and accelerated creep at 65 and 70% of their ultimate tensile strength. Variability in the ultimate tensile strength of the webbings is investigated and compared with variability in the creep life response. Additional testing studied the effects of load and displacement rate, specimen length and the time-dependent effects of preconditioning the webbings. The creep test facilities, instrumentation and test procedures are also detailed. The accelerated creep tests display consistently longer times to failure than their real-time counterparts; however, several factors were identified that may contribute to the observed disparity. Test setup and instrumentation, grip type, loading scheme, thermal environment and accelerated test postprocessing along with material variability are among these factors. Their effects are discussed and future work is detailed for the exploration and elimination of some of these factors in order to achieve a higher fidelity comparison.

Jones, Thomas C.↗
DOE OSTI2020

ICME for Creep of Ni-Base Superalloys in Advanced Ultra-Supercritical Steam Turbines

The goal of this project contains three major aspects: (1) critical assessment of existing experimental data, (2) critical assessment of existing modeling capabilities and (3) development of new modeling capabilities that are critical but currently missing in predicting long-term creep behavior of Ni-base superalloys used in advanced ultra- supercritical (A-USC) steam turbines for coal-fired power plants. The project uses advanced materials informatics to datamine the experimental data, uncertainty quantification tools to rigorously assess existing creep-life models, and integration of phase-field and FFT-based crystal plasticity to develop a multi-scale, physics-based, microstructure-sensitive creep model.

20 FOSSIL-FUELED POWER PLANTS↗
NASA NTRS1983

Development of a simplified procedure for rocket engine thrust chamber life prediction with creep

An analytical method for predicting engine thrust chamber life is developed. The method accounts for high pressure differentials and time-dependent creep effects both of which are significant in limiting the useful life of the shuttle main engine thrust chamber. The hot-gas-wall ligaments connecting adjacent cooling channels ribs and separating the coolant flow from the combustion gas are subjected to a high pressure induced primary stress superimposed on an alternating cyclic thermal strain field. The pressure load combined with strain-controlled cycling produces creep ratcheting and consequent bulging and thinning of these ligaments. This mechanism of creep-enhanced ratcheting is analyzed for determining the hot-gas-wall deformation and accumulated strain. Results are confirmed by inelastic finite element analysis. Fatigue and creep rupture damage as well as plastic tensile instability are evaluated as potential failure modes. It is demonstrated for the NARloy Z cases analyzed that when pressure differentials across the ligament are high, creep rupture damage is often the primary failure mode for the cycle times considered.

Badlani, M. L.↗
DOE OSTI2021

Effect of heat treatment on creep behavior of 316 L stainless steel manufactured by laser powder bed fusion

The objective of this study is to understand the thermal stability of microstructure and its effect on the creep behavior of additively-manufactured 316L stainless steel (AM 316L SS). Creep specimens were fabricated from rods printed by a laser powder bed fusion process. Six different heat treatments, namely 650 °C/1 h, 700 °C/1 h, 750 °C/1 h, 800 °C/1 h, 900 °C/1 h and 1050 °C/1 h were applied to the creep specimens. The heat-treated specimens were creep-tested under the same condition, 550 °C/275 MPa to evaluate the effect of post-build heat treatment on the creep behavior of AM 316L SS. In the temperature range of 650-750 °C, dislocation density within cells, and cell size and wall thickness were affected by the heat treatment, while elemental segregation at boundaries remained unchanged and Mn-enriched Si oxide particles remained stable. In the temperature range of 750-900 °C, concurrent changes were observed in dislocation cell structures, elemental segregation and oxide particles. The 1050 °C-heat treatment removed cell structures and boundary solute segregations, leading to formation of equiaxed grains; Mn-enriched Si oxide particles in the as-built specimen were replaced by more stable Mn-enriched Cr oxides. The creep life of AM 316L SS increased after the heat treatment at 650 °C and then decreased with increasing temperature up to 900 °C where cell/subgrain structures still existed. The creep rate and creep elongation followed an opposite trend. The creep rate can be correlated with the structural parameters of cell/subgrain size and cell wall/boundary thickness and can be rationalized by different strengthening mechanisms of dislocation cells and subgrains. The heat treatment affected strongly the primary and secondary creep but had a minimal effect on the tertiary creep of AM 316L SS.

316L stainless steel↗
DOE OSTI2025

Laser Powder Bed Fusion Manufactured Alloys 625 and 282 and Properties Relevant to Advanced Nuclear Components

Under the Advanced Materials and Manufacturing Technologies program, two Ni-based alloys fabricated by laser powder bed fusion (LPBF) have been evaluated: γ′-strengthened Haynes 282 and solution-strengthened Inconel 625. Large printing defects were observed in the LPBF 282 alloy fabricated using a Renishaw AM250 machine, likely due to particle spattering during printing. Annealing at 1,180°C for 1 h followed by 4 h at 800°C in a high density of 50 nm γ′-strengthening precipitates as well as partial recrystallization resulted in a bimodal grain distribution. Creep testing performed at 750°C revealed lower creep life and ductility for the LPBF 282 compared with wrought 282. X-ray computed tomography combined with optical and scanning electron microscopy microstructural characterization revealed crack formation during creep testing, initiated either from printing defects or from creep cavitation at grain boundaries. Printing defects were the likely reason for the lower creep performance of LPBF 282 and could be suppressed by optimizing the build configuration. Printing 625 on an EOS M290 machine using the recommended EOS parameters resulted in a very low defect density. Superior creep strength at 725°C was observed for the as-printed LPBF 625 along the build direction when compared with wrought 625. No defect larger than ~50 µm could be detected by X-ray computed tomography in the as-printed conditions and after creep testing for 1,000 h at 725°C and 150 MPa. Small, needle-like δ-phase precipitates were observed after creep testing for 100 h at 725°C and 200 MPa. The rapid formation of the γ phase is directly related to the initial Nb and Mo segregation in the LPBF 625 cell walls, and its effect on the alloy’s high-temperature performance will be evaluated. Solution annealing was carried out at 1,150°C for 1 h and led to full recrystallization of the alloy. A decrease in strength and increase in ductility were observed after solution annealing, and the alloy recrystallization resulted in isotropic tensile properties at room temperature, contrary to what was observed for the as-printed LPBF 625.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS2020

Development of a Compact, Low Cost Test Fixture to Evaluate Creep in High Strength Softgoods Materials under Constant Environmental Control

Space exploration is typically driven by two key factors: cost and payload mass. Therefore creating relatively low cost, low mass space hardware is critical. With the advancement of new high-strength flexible materials, a new chapter is opening in the evolution of pressurized space structures. Space-rated inflatable structures are attractive due to their low mass, compact stowage, and capability of performing as well, or better than, their rigid counterparts for applications such as habitats and airlocks. The lifetime properties of materials used for inflatable structures are not as well characterized as heritage composite and metallic materials; therefore, they require extensive testing to increase the level of confidence in their use. Creep testing is one method of evaluating the expected lifetime of materials that may be under constant load for many years in operational use. Conventional creep testing of high-strength softgoods webbings or cordage requires a large, temperature-controlled facility, with structural frames capable of supporting large dead weights, weighing thousands of pounds on each specimen. This is expensive and takes up a significant amount of volume in a facility for a long time. This paper describes the design and analysis of a low-cost, low-volume creep test stand that can be locally environmentally controlled, so that smaller, cheaper facilities can be used for characterizing the creep life of the softgoods materials used in inflatable space structures.

Softgoods↗
NASA NTRS1971

Generation of long time creep data on refractory alloys at elevated temperatures

Ultrahigh vacuum creep tests were performed on tungsten, molybdenum, and tantalum alloys to develop design creep data and to evaluate the influence of liquid lithium exposure on the creep resistance of a tantalum alloy. Test conditions were generally selected to provide 1% creep in 1000 to 10,000 hours, with the test temperatures ranging between 1600 and 2900 F (1144 K and 1866 K). One percent creep life data from a tantalum-base T-111 alloy (Ta-8%W-2%Hf) were analyzed using a station function method to provide an improved parametric representation of the T-111 data. In addition, the minimum creep rate data from an ASTAR 811C alloy (Ta-8%W-1%Re-0.7%Hf0.025%C) were analyzed to determine the stress and temperature dependence of creep rate. Results of this analysis indicated that the activation energy for creep decreased from about 150 Kcal/mole (5130 J/mole) above 2400 F (1589 K) to about 110 Kcal/mole (3760 J/mole) below 2000 F (1361 K). This temperature range corresponds to the range where the creep mechanism changes from grain boundary sliding to intragranular creep.

Sheffler, K. D.↗
DOE OSTI2020

An Alternative Casting Technique to Improve the Creep Resistance of Cast INCONEL Alloy 740H

The increasing performance requirements of power plant designs, such as advanced-ultra supercritical (A-USC), require the use of Ni-based superalloys to replace high-strength, ferritic-martensitic steels for components subjected to temperatures above 898 K (625 °C) and for austenitic stainless steels components at temperatures above 973 K (700 °C). To date, commercial Ni-based superalloy INCONEL 740H has been shown to be appropriate for use in A-USC power plants as boiler components in a wrought product. However, large complex components in boilers as well as other casings in the turbine and valve chest require castings of a thick-wall nature. Using the alloy in its cast form would be significantly valuable in terms of range of component size, geometry and complexity. Previous investigations revealed short creep lives from cast INCONEL alloy 740H. Here in this investigation, an alternative casting route that utilized a melt procedure resulting in a fine-grain casting, and in conjunction with a computationally optimized homogenization heat treatment, not only controlled the grain size and grain boundary structure but minimized chemistry variability and segregation. A primarily equiaxed and homogenous grain size distribution was obtained from this approach with better repartition of M 23 C 6 carbides along the grain boundaries. Furthermore, better than 38 pct increase was obtained for this material in comparison to the creep life obtained from the best performing conventionally cast material. More importantly, the fine-grain homogenized (FGH) casting route resulted in the Larson–Miller plot for this material that coincided with that of wrought alloy 740. At low creep stresses (with a test still in progress), the FGH casting is resulting in higher values of the LMP than the wrought alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Manufacturability and performance response of developed Ni-based alloys for reactor environments

Under the Advanced Materials and Manufacturing Technologies program, two Ni-based alloys fabricated by laser powder bed fusion (LPBF) at Oak Ridge National Laboratory and by laser powder directed energy deposition (LP-DED) at Idaho National Laboratory have been evaluated: γ′-strengthened Haynes 282 and solution-strengthened Inconel 625. Printing defects were observed in the LPBF 282 alloy fabricated using a Renishaw AM250 machine, likely due to particle spattering during printing. For both the LPBF and LP-DED 282 alloys, annealing at 1,180°C for 1 h resulted in partial recrystallization and a bimodal grain distribution, and subsequent aging for 4 h at 800°C led to the formation of a high density of nano-size γ′-strengthening precipitates. Creep testing performed at 750°C revealed lower creep life and ductility for the LPBF and LP-DED 282 compared with wrought 282. X-ray computed tomography combined with optical and scanning electron microscopy microstructural characterization revealed crack formation in the LPBF 282 alloy during creep testing, initiated either from printing defects or from creep cavitation at grain boundaries. Creep cavitation and cracking at grain boundaries were also observed for the LP-DED 282 alloy, and optimization of the printing strategies and postheat treatments will be needed to fabricate high-performance 282 components for high-temperature nuclear applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Manufacturability and performance response of developed Ni-based alloys for reactor environments

Under the Advanced Materials and Manufacturing Technologies program, two Ni-based alloys fabricated by laser powder bed fusion (LPBF) at ORNL and laser powder directed energy deposition (LP-DED) at INL have been evaluated: γ′-strengthened Haynes 282 and solution-strengthened Inconel 625. Printing defects were observed in the LPBF 282 alloy fabricated using a Renishaw AM250 machine, likely due to particle spattering during printing. For both the LPBF and LP-DED 282 alloys, annealing at 1,180°C for 1 h resulted in partial recrystallization and a bimodal grain distribution, while subsequent aging for 4 h at 800°C led to the formation of a high density of nano size γ′-strengthening precipitates. Creep testing performed at 750°C revealed lower creep life and ductility for the LPBF and LP-DED 282 compared with wrought 282. X-ray computed tomography combined with optical and scanning electron microscopy microstructural characterization revealed crack formation in the LPBF 282 alloy during creep testing, initiated either from printing defects or from creep cavitation at grain boundaries. Creep cavitation and cracking at grain boundaries were also observed for the LP-DED 282 alloy, and optimization of the printing strategies and post heat treatments will be needed to fabricate high performance 282 components for high temperature nuclear applications.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Creep Resistant Martensitic Steels for Operation at High-Temperatures in Power Generation Applications

Increasing the temperature capabilities of ferritic/martensitic 9-12% Cr steels can help in increasing the operating temperature of land-based turbines and minimize the use of expensive high-temperature alloys in the hot section. A creep resistant martensitic steel, JMP, was developed with the potential to operate at or above 650°C. The design of the alloys originated from computational modeling for phase stability and precipitate strengthening using fifteen constituent elements. Cobalt was used for increased solid solution strengthening, Si for oxidation resistance and different W and Mo concentrations for matrix strength and stability. The JMP steels showed increases in creep life compared to MARBN/SAVE12AD at 650°C for testing at various stresses between 138 MPa and 207 MPa. On a Larson-Miller plot, the performance of the JMP steels surpasses that of state-of-the-art MARBN steel. Approximately 21 years of cumulative creep data are reported for the JMP steels which encompasses various compositions. The relationships between composition-microstructure-creep properties are discussed including characterization of microstructures after >20,000 hours in creep.

Detrois, Martin↗
DOE OSTI2023

Mechanisms for high creep resistance in alumina forming austenitic (AFA) alloys

Castable alumina forming austenitic (AFA) alloys have demonstrated superior creep life and oxidation resistance at temperatures exceeding 800⁰C. Despite the success in the applicability of these alloys in extreme environments, there is a limited understanding of the deformation modes and the influence of each alloying element guiding the alloy design strategies that could further enhance the creep strength of these AFA alloys, particularly at temperatures at and above 900⁰C. In this study, we reveal the mechanism underpinning the superior creep performance of castable AFA alloys that involves suppressing primary carbide formation through minor compositional modification. This approach results in a three-fold increase in creep strength at 900⁰C and 50 MPa. Here, by employing integrated characterization techniques, we analyzed the microstructures of two AFA alloys, both before and after the creep process. We discovered that the suppression of primary carbides permits the in-situ clustering of now-available interstitial elements such as C, Si, and O during high-temperature creep. This improved solid solution strengthening and reduced stacking fault energy of the alloy. Moreover, it also enabled controlled secondary carbide formation during testing, further improving the creep resistance. These findings underline the important interplay between alloy composition, microstructure, and creep properties, and offer a promising design strategy for developing economical high-temperature Fe-based alloys suitable for advanced applications.

36 MATERIALS SCIENCE↗
NASA NTRS1999

Viscoplastic Constitutive Theory Demonstrated for Monolithic Ceramic Materials

Development of accurate three-dimensional (multiaxial) inelastic stress-strain models is critical in utilizing advanced ceramics for challenging 21st century high-temperature structural applications. The current state of the art uses elastic stress fields as a basis for both subcritical crack growth and creep life prediction efforts aimed at predicting the time dependent reliability response of ceramic components subjected to elevated service temperatures. However, to successfully design components that will meet tomorrow's challenging requirements, design engineers must recognize that elastic predictions are inaccurate for these materials when subjected to high-temperature service conditions such as those encountered in advanced heat engine components. Analytical life prediction methodologies developed for advanced ceramics and other brittle materials must employ accurate constitutive models that capture the inelastic response exhibited by these materials at elevated service temperatures. A constitutive model recently developed at the NASA Lewis Research Center helps address this issue by accounting for the time-dependent (inelastic) material deformation phenomena (e.g., creep, rate sensitivity, and stress relaxation) exhibited by monolithic ceramics exposed to high-temperature service conditions. In addition, the proposed formulation is based on a threshold function that is sensitive to hydrostatic stress and allows different behavior in tension and compression, reflecting experimental observations obtained for these material systems.

Janosik, Lesley A.↗
NASA NTRS1984

Development of improved low-strain creep strength in Cabot alloy R-41 sheet

The feasibility of improving the low-strain creep properties of a thin gauge nickel base sheet alloy through modified heat treatment or through development of a preferred crystal-lographic texture was investigated. The basic approach taken to improve the creep strength of the material by heat treatment was to increase grain size by raising the solution treatment temperature for the alloy to the range of 1420 K to 1475 K (2100 F to 2200 F). The key technical issue involved was maintenance of adequate tensile ductility following the solutioning of M6C primary carbides during the higher temperature solution treatment. The approach to improve creep properties by developing a sheet texture involved varying both annealing temperatures and the amount of prior cold work. Results identified a heat treatment for alloy R-14 sheet which yields a substantial creep-life advantage at temperatures above 1090 K (1500 F) when compared with material given the standard heat treatment. At the same time, this treatment provides reasonable tensile ductility over the entire temperature range of interest. The mechanical properties of the material given the new heat treatment are compared with those for material given the standard heat treatment. Attempts to improve creep strength by developing a sheet texture were unsuccessful.

Rothman, M. F.↗
DOE OSTI2022

Exploring the Impact of N Solubility and Trace Elements on the Creep Properties of P92 Steel

Trace elements can have major consequences on the properties of creep resistant martensitic steels. To better understand the changes in microstructure and mechanical performance associated with the variation of trace elements and enable design of steels operating at more demanding conditions, we formulated three versions of P92 within the specified allowable N, B, C and Si ranges. Different service conditions were explored, and >80% decrease in creep life was observed at 625°C 155MPa for the highest B and N containing alloy. Multiscale characterization (OM, SEM, TEM) revealed key changes due to the trace element variation. The high trace content alloy formed deleterious BN precipitates with morphology that would promote crack nucleation, but also formed higher fractions of beneficial MX precipitates. The alloy with the lowest trace content showed the best creep performance – a result of the refined precipitate populations and the absence of large-scale inclusions and BN precipitates.

Antonov, Stoichko↗
DOE OSTI2023

Variations in Creep Performance of P92 Steel Within Its Composition Range: Influence of N Solubility

Underspecified composition ranges often lead to alloys with unpredictable mechanical performance. To better understand the changes in microstructure and mechanical performance associated with variations of key elements, three versions of P92 are formulated within, or close to, the specified allowable for N, B, and C ranges. Chromium and Si are also varied to influence N solubility. Different service conditions (i.e., temperature and stress) are explored. It is observed that >80% decrease in creep life occurs at 625 °C and 155 MPa for the highest B and N containing alloy. Multiscale characterization reveals key changes due to the trace element variation. The high B and N containing alloy forms deleterious BN precipitates with morphology that promotes crack nucleation and damage accumulation, but this alloy additionally forms higher fractions of beneficial MX precipitates. The alloy with the lowest B and N concentrations but greater C content shows the best creep performance—a consequence of the refined M 23 C 6 carbide precipitate population and the absence of large-scale inclusions or BN precipitates. Calculations of creep activation energy reveal that the high B and N containing alloy is more prone to damage accumulation which causes an early onset of accelerating creep and greater minimum creep rate.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Evaluation of thermal energy storage for central receiver concentrating solar power plants under charging cycles through structural assessment

Electricity production by concentrated solar power (CSP) systems has stood out among energy transition alternatives due to their large generation capacity (between 30 MW and 400 MW) and high capacity factor (80%) when incorporating thermal storage systems (TES). Although TES tanks in operation worldwide are made of austenitic steels with remarkable mechanical and anticorrosive properties, operational failures have been reported due to low-cycle fatigue, creep, and the abrupt release of residual stresses generated during tank manufacturing. A critical operation for salt tanks is the initial daily charging operation, given the low fluid level and the thermal gradients between the inventory and the salt entering the tank. This study presents a structural simulation of a 39.6 m-diameter molten salt tank for central receiver CSP plants, accounting for temperature and pressure variations during charging and different sparger ring inlet configurations. The initial pre-stressed condition of the floor, resulting from the manufacture of welded plates, is used as a boundary condition. The fatigue and creep life analyses were performed in accordance with the ASME BPVC and API standards. It was found that the tank's floor is in a less favourable mechanical condition than the wall, due to its initial manufacturing condition and the maximum temperature differences during charging. A critical zone was identified in an area affected by residual stress on the floor and under the sparger ring. The baseline sparger ring configuration, with 52 2-inch-diameter orifices and a flow direction of 90 degrees , results in an average floor stress of approximately 25 MPa and creep damage after 1.2 years of tank operation.

14 SOLAR ENERGY↗