SEARCH · Search NASA

Results for “crosswind”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1973

An experimental investigation of a highly underexpanded sonic jet ejecting from a flat plate into a subsonic crossflow

The induced static pressures due to a highly underexpanded sonic jet ejecting normally from a flat plate into a subsonic crosswind have been investigated. These pressure data have been recorded on the flat plate for a range of nominal jet-to-free-stream dynamic-pressure ratios from 0 to 1000 at free-stream Mach numbers of 0.1, 0.2, 0.4, and 0.6. The static pressure data measured on the flat plate are presented and correlated based upon the Riemann shock geometry in the jet plume. This data correlation improves with increasing free-stream Mach number.

Shaw, C. S.↗

NASA NTRS1973

A 727 airplane center duct inlet low speed performance confirmation model test for refanned JT8D engines, phase 2

The results from testing of a 0.3 scale model center duct inlet (S duct) for the Pratt and Whitney Aircraft JT8D-100 engines are presented. The objective of this test was to demonstrate that the required airflow of the JT8D-100 engine (480 lb/sec as compared to 334 lb/sec for JT8D-15) can be achieved with minimum modifications to the existing 727 airplane structure at acceptable levels of total pressure recovery and distortion. Steady-state pressure recovery, steady-state pressure distortion, and dynamic pressure measurements were taken at the engine face station. Surface static pressure measurements were taken along the duct. Test results indicated that the required airflow was achieved with acceptable pressure recovery (comparable to the current 727-200 S duct). Inlet inflow angle variation within the 727 airplane operating regime (minus 5 to 5 degrees) had no effect on the inlet performance. Pressure distortion at static and forward speed at takeoff airflow conditions are within P and WA limits for the Phase II duct when equipped with vortex generators. Static crosswind operation between 10 knots and 25 knots appears feasible at full takeoff power.

Kaldschmidt, G.↗

NASA NTRS1974

Curved descending landing approach guidance and control

Linear optimal regulator theory is applied to a nonlinear simulation of a transport aircraft performing a helical landing approach. A closed form expression for the quasi-steady nominal flight path is presented along with the method for determining the corresponding constant nominal control inputs. The Jacobian matrices and the weighting matrices in the cost functional are time varying. A method of solving for the optimal feedback gains is reviewed. The control system is tested on several alternative landing approaches using both three and six degree flight path angles. On each landing approach, the aircraft was subjected to large random initial state errors and to randomly directed crosswinds. The system was also tested for sensitivity to changes in the parameters of the aircraft and of the atmosphere. Performance of the optimal controller on all the three degree approaches was very good, and the control system proved to be reasonably insensitive to parametric uncertainties.

Crawford, D. J.↗

NASA NTRS1975

Aerodynamic analysis of several high throat Mach number inlets for the quiet clean short-haul experimental engine

The results of an analytical study to investigate internal and external surface Mach numbers on several inlet geometries for possible application to the nacelle of the Quiet Clean Short-Haul Experimental Engine (QCSEE) are presented. The effects of external forebody geometry and internal lip geometry were illustrated at both low-speed and cruise conditions. Boundary-layer analyses were performed on several geometries to determine if lip flow separation might exist. The results indicated that inner-surface Mach number level and gradient could be reduced with inlets at a 50 deg incidence angle by blunting the external forebody geometry. The external Mach numbers at cruise conditions indicated that a compromise in the external forebody bluntness might be required to satisfy both low-speed and cruise conditions. For a fixed value of bluntness parameter, no lip flow separation was indicated for the 1.46- and 1.57-area-contraction-ratio inlets at low-speed conditions. However, a lip separation condition was obtained with the 1.37-contraction-ratio inlet. The QCSEE nacelle design takeoff operating condition (incidence angle of 50 deg and free-stream Mach number of 0.12) resulted in higher peak surface Mach numbers than the design crosswind (incidence angle of 90 deg and free-stream Mach number of 0.05) or static condition.

Albers, J. A.↗

NASA NTRS1975

Normal probabilities for Vandenberg AFB wind components - monthly reference periods for all flight azimuths, 0- to 70-km altitudes

Vandenberg Air Force Base (AFB), California, wind component statistics are presented to be used for aerospace engineering applications that require component wind probabilities for various flight azimuths and selected altitudes. The normal (Gaussian) distribution is presented as a statistical model to represent component winds at Vandenberg AFB. Head tail, and crosswind components are tabulated for all flight azimuths for altitudes from 0 to 70 km by monthly reference periods. Wind components are given for 11 selected percentiles ranging from 0.135 percent to 99.865 percent for each month. The results of statistical goodness-of-fit tests are presented to verify the use of the Gaussian distribution as an adequate model to represent component winds at Vandenberg AFB.

Falls, L. W.↗

NASA NTRS1975

Induced pressure distribution of a jet in a crossflow

The turbulent flow of a subsonic round jet exhausting perpendicularly from a flat plate into a subsonic crosswind of the same temperature was investigated in the Langley V/STOL tunnel. The large test section of this tunnel made it possible to use a jet with the relatively large diameter of 10.16 cm. Pressures were measured on the flat plate at over 400 locations to provide a detailed description of the static pressure distribution. Results are presented in tabular and graphical forms for jet to crossflow velocity ratios ranging from 2 to 10, and comparisons are made with results of other experiments. The results indicate that the dominant flow parameter affecting the pressure distributions is the ratio of jet to crossflow velocities. The distribution of turbulence on the plate also appears to be a function of velocity ratio.

Fearn, R. L.↗

NASA NTRS1975

Automatic guidance and control of a transport aircraft during a helical landing approach

A linear optimal regulator theory was applied to a nonlinear simulation of a transport aircraft performing a helical landing approach. A closed-form expression for the quasi-steady nominal flight path is presented along with the method for determining the corresponding constant nominal control inputs. The Jacobian matrices and the weighting matrices in the cost functional were time varying. A method of solving for the optimal feedback gains is reviewed. The control system was tested on several alternative landing approaches using both 3 deg and 6 deg flight path angles. On each landing approach, the aircraft was subjected to large random initial-state errors and to randomly directed crosswinds. The system was also tested for sensitivity to changes in the parameters of the aircraft and of the atmosphere. Results indicate that performance of the optimal controller on all the 3 deg approaches is very good. The control system proved to be reasonably insensitive to parametric uncertainties. Performance is not as good on the 6 deg approaches. A modification to the 6 deg flight path was proposed for the purpose of improving performance.

Crawford, D. J.↗

NASA NTRS1975

Design and testing of new center inlet and S-duct for B-727 airplane with refanned JT8D engines

The work described in this paper was part of the NASA refan program. The airflow requirement of the refanned JT8D (-100 series) engine increased about 50% above that of the basic JT8D. This required a redesign of the center inlet and S-duct of the Boeing 727 airplane. The paper describes the design constraints for the S-duct and the analytic method used to define the lines of the new duct. Model tests that were conducted at static, angle-of-attack, and crosswind conditions are described with a variety of flow control devices. Test results showed that the new inlet and S-duct have a pressure recovery comparable to that of the existing inlet. By employing corotating vortex generators, less flow distortion was obtained for the core region than the existing duct has with its counter rotating vortex generators.

Ting, C. T.↗

NASA NTRS1975

Wind modeling and lateral control for automatic landing

For the purposes of aircraft control system design and analysis, the wind can be characterized by a mean component which varies with height and by turbulent components which are described by the von Karman correlation model. The aircraft aero-dynamic forces and moments depend linearly on uniform and gradient gust components obtained by averaging over the aircraft's length and span. The correlations of the averaged components are then approximated by the outputs of linear shaping filters forced by white noise. The resulting model of the crosswind shear and turbulence effects is used in the design of a lateral control system for the automatic landing of a DC-8 aircraft.

Holley, W. E.↗

NASA NTRS1976

Aerodynamic performance of flared fan nozzles used as inlets

Tests were conducted in a low speed wind tunnel to determine the aerodynamic performance of several flared fan nozzles. Each of the flared nozzles was a downstream-facing inlet to a model fan that was used to simulate a variable pitch fan during reverse thrust operation. The total pressure recovery of each of the flared nozzles as well as that of an unflared nozzle and a serrated flare nozzle was obtained for comparison. The aerodynamic performance of a selected flared nozzle was considered in further detail. The nozzle surface pressures for a flared nozzle were also determined. Results indicated that the differences in aerodynamic performance among the nozzles were most apparent at the wind-tunnel-off condition. A nonzero free stream velocity significantly reduced the perforamnce of all the nozzles, and crosswind flow (free stream flow perpendicular to the model axis) further reduced the performance of the nozzles. The unflared nozzle and the serrated flare nozzle had reduced aerodynamic performance compared to a solid surface flared nozzle.

Dietrich, D. A.↗

NASA NTRS1976

Experimental measurements of the ground cloud growth during the 11 February 1974, Titan-Centaur launch at Kennedy Space Center

The Titan-Centaur was launched from Kennedy Space Center on February 11, 1974 at 0948 eastern daylight time. Ground level effluent measurements were obtained from the solid rocket motors for comparison with NASA diffusion models for predicting effluent ground level concentrations and cloud behavior. The results obtained provide a basis for an evaluation of such key model inputs such as cloud rise rate, stabilization altitude, crosswind growth, volume expansion, and cloud trajectory. Ground level effluent measurements were limited because of changing meteorological conditions, incorrect instrument location, and operational problems. Based on the measurement results, operational changes are defined. Photographs of the ground exhaust clouds are shown. The chemical composition of the exhaust gases was analyzed and is given.

Stewart, R. B.↗

NASA NTRS1975

Entry reaction control system propellant analysis. Flight control integration

The effects of winds, sideslip angle feedback, and the data reference (air or inertial) on the Reaction Control System (RCS) propellant requirements during entry were investigated. It was determined that in the presence of a 3 sigma crosswind an addition 188 pounds of RCS propellant was required for entry control which is within the present 200 pound allotment for winds. The absence of air data information does result in slightly higher RCS propellant demands.

Devall, O. R.↗

NASA NTRS1975

Aircraft wake vortex velocity measurements using a scanning CO2 laser Doppler velocimeter

A CO2 laser Doppler velocimeter was employed in the study of pairs of counterrotating vortices trailing aircraft in an airport air space. A laser positioned on an extended runway centerline scans a vertical plane perpendicular to the centerline. Vortex location, measurement of vortex transport, and measurement of the properties of aircraft wake vortex flow fields are achieved via spectral analysis of the data. Highest amplitude in the spectrum, the associated maximum velocity, the highest velocity above the amplitude threshold, and the total number of frequency (velocity) cells above thresholds are studied as parameters in analysis of the vortex-associated flow field. The profile of the radial variation of tangential velocity is studied, and two special problems are examined: location of the vortex center and error introduced by crosswind.

Dimarzio, C. A.↗

NASA NTRS1977

Tail contribution to the directional aerodynamic characteristics of a 1/6-scale model of the rotor systems research aircraft with a tail rotor

The results are presented of a wind tunnel investigation to determine the tail contribution to the directional aerodynamic characteristics of a 1/6-scale model of the rotor systems research aircraft (RSRA) with a tail rotor. No main rotor was used during the investigation. Data were obtained with and without the tail rotor over a range of sideslip angle and over a range of rotor collective pitch angle. The model with the tail rotor was tested at several advance ratios with and without thrust from the auxiliary thrust engines on the RSRA fuselage. Increasing the space between the tail-rotor hub and the vertical tail reduced the tail-rotor torque required at moderate to high rotor thrust. Increasing the exit dynamic pressure of the auxiliary thrust engines decreases the tail contribution to the static directional stability. The tail-rotor thrust and its interference provide a positive increment to the static directional stability. The tail contribution increases with forward speed. The adverse yawing moment of the airframe would strongly affect the thrust required of the tail rotor when the helicopter is hovering in a crosswind.

Mineck, R. E.↗

NASA NTRS1977

Ground winds and winds aloft Edwards AFB, California

Ground level runway wind statistics cover crosswind, tailwind, and headwind reversal percentage frequencies with respect to month and hour for the two major runways. Also presented are bivariate normal wind statistics for a 90 degree flight azimuth for altitudes 0 through 27 km. Wind probability distributions, synthetic vector wind profiles, and statistics for any rotation of axes are computed from five given parameters.

Johnson, D. L.↗

NASA NTRS1978

Ground winds and winds aloft for Edwards AFB, California (1978 revision)

Ground level runway wind statistics for the Edwards AFB, California area are presented. Crosswind, headwind, tailwind, and headwind reversal percentage frequencies are given with respect to month and hour for the two major Edwards AFB runways. Also presented are Edwards AFB bivariate normal wind statistics for a 90 degree flight azimuth for altitudes 0 through 27 km. Wind probability distributions and statistics for any rotation of axes can be computed from the five given parameters.

Johnson, D. L.↗

NASA NTRS1978

Experimental investigation of effect of jet decay rate on jet-induced pressures on a flat plate

An experimental study of the interaction between a lift jet and an aircraft wing for a jet VTOL aircraft was performed for the simplified model of an unheated, subsonic, circular jet exiting at right angles to a flat plate into a uniform subsonic crosswind. The effects of jet dynamic pressure decay rate upon the jet location and jet induced pressure distribution on the plate were studied over a range of jet to crossflow velocity ratios of 2.2 or = R or = 10. Jet decay rate was varied through use of cylindrical centerbodies with flat or hemispherical tips submerged in the jet nozzle at various depths below the jet exit plane. Quicker jet dynamic pressure decay, caused by the presence of a centerbody, resulted in reductions in the jet induced lift loss by as much as 45 percent relative to values for jets with no centerbody. These reductions in lift loss were observed at the larger values of crossflow velocity.

Kuhlman, J. M.↗

NASA NTRS1978

Atmospheric-wake vortex interactions

The interactions of a vortex wake with a turbulent stratified atmosphere are investigated with the computer code WAKE. It is shown that atmospheric shear, turbulence, and stratification can provide the dominant mechanisms by which vortex wakes decay. Computations included the interaction of a vortex wake with a viscous ground plane. The observed phenomenon of vortex bounce is explained in terms of secondary vorticity produced on the ground. This vorticity is swept off the ground and advected about the vortex pair, thereby altering the classic hyperbolic trajectory. The phenomenon of the solitary vortex is explained as an interaction of a vortex with crosswind shear. Here, the vortex having the sign opposite that of the sign of the vorticity in the shear is dispersed by a convective instability. This instability results in the rapid production of turbulence which in turn disperses the smoke marking the vortex.

Bilanin, A. J.↗