Search NASA⌕ Search

SEARCH · Search NASA

Results for “design for manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Electronic Design Automation: Integrating the Design and Manufacturing Functions

As the complexity of electronic systems grows, the traditional design practice, a sequential process, is replaced by concurrent design methodologies. A major advantage of concurrent design is that the feedback from software and manufacturing engineers can be easily incorporated into the design. The implementation of concurrent engineering methodologies is greatly facilitated by employing the latest Electronic Design Automation (EDA) tools. These tools offer integrated simulation of the electrical, mechanical, and manufacturing functions and support virtual prototyping, rapid prototyping, and hardware-software co-design. This report presents recommendations for enhancing the electronic design and manufacturing capabilities and procedures at JSC based on a concurrent design methodology that employs EDA tools.

Bachnak, Rafic↗
NASA NTRS2012

Design and Manufacturing Considerations for Shockproof and Corrosion-Immune Superelastic Nickel-Titanium Bearings for a Space Station Application

An intermetallic nickel-titanium alloy, 60NiTi (60wt%Ni, 40wt%Ti), is a promising tribological material for space mechanisms. 60NiTi offers a broad combination of physical properties that make it unique among bearing materials. 60NiTi is hard, electrically conductive, highly corrosion resistant, readily machined prior to final heat treatment, easily lubricated and is non-magnetic. It also falls within the class of superelastic alloys and can elastically endure large strains (beyond 5 percent) making it highly resistant to excessive and unexpected (shock) loads. Key material properties and characteristics such as elastic modulus, tensile fracture sensitivity and residual stress behavior, however, differ from conventional alloys such as steel and this significantly affects bearing design and manufacturing. In this paper, the preliminary design and manufacture of ball bearings made from 60NiTi are considered for a highly corrosive, lightly loaded, low speed bearing application found inside the International Space Station s water recycling system. The information presented is expected to help guide more widespread commercialization of this new technology into space mechanism and other applications.

DellaCorte, Christopher↗
NASA NTRS2002

Design and Manufacturing of Extremely Low Mass Flight Systems

Extremely small flight systems pose some unusual design and manufacturing challenges. The small size of the components that make up the system generally must be built with extremely tight tolerances to maintain the functionality of the assembled item. Additionally, the total mass of the system is extremely sensitive to what would be considered small perturbations in a larger flight system. The MUSES C mission, designed, built, and operated by Japan, has a small rover provided by NASA that falls into this small flight system category. This NASA-provided rover is used as a case study of an extremely small flight system design. The issues that were encountered with the rover portion of the MUSES C program are discussed and conclusions about the recommended mass margins at different stages of a small flight system project are presented.

Johnson, Michael R.↗
NASA NTRS2019

Integrated Design and Manufacturing Analysis for Automated Fiber Placement Structures

Automated fiber placement provides many advancements beyond traditional hand layups in terms of efficiency and reliability. However, there are also a variety of unique challenges that arise with automated fiber placement technology. In particular, steering of tows over doubly-curved tool surfaces can result in material overlaps and gaps due to path convergence/divergence, fiber angle deviation, as well defects in the tows themselves such as puckers and wrinkles. Minimization of these defects is traditionally considered a task for the manufacturing discipline. Manufacturing specifications are often created for these defects based on laminate testing and can be inflexible to avoid more tests. Recent efforts have been made under the National Aeronautics and Space Administration (NASA) Advanced Composites Project (ACP) to develop software tools and processes that provide automated coupling between design and manufacturing disciplines. The objective of this coupling is to provide information to the design discipline on the manufacturability of a laminate while the laminate is being designed. A variety of software tools, both existing commercial tools and research tools under development, will be used to achieve this objective: HyperSizer for laminate optimization, the Computer Aided Process Planning module for selection of manufacturing process parameters, Vericut Composite Programming for tow path simulation, and COMPRO for deposition and cure defects. The newly developed “Central Optimizer” tool will be used to tie the modules together and drive the design for manufacturing process.

Noevere, August↗
NASA NTRS2020

Design for Manufacturing Tool for Automated Fiber Placement Structures - Verification and Validation

A tool has been developed to address the growing Design for Manufacturing needs for composite structures, specifically those manufactured with automated fiber placement. This manufacturing approach presents unique challenges associated with puckers and wrinkling, tow overlaps and gaps, fiber deviation, and laminate strength. Achieving a satisfactory laminate design usually requires finding compromises between those four areas. The developed tool, dubbed the Central Optimizer, assists with the process of balancing competing design metrics in automated fiber placement. This tool was developed under the NASA Advanced Composites Consortium with input from industry partners. Under this program, the Central Optimizer has been exercised on three different structures to verify its functionality and validate ability to improve the design process for automated fiber placement structures.

August T Noevere↗
NASA NTRS1997

Technology Needs for Reduced Design and Manufacturing Cost of Commercial Transport Engines

The objective of the study was to assess the needs in the design and manufacturing processes and identify areas where technology could impact in cost and cycle-time reduction. At the highest level, the team first identified the goals that were in line with long-range needs of the aeropropulsion industry, and to which technology and process improvements would be required to contribute. These goals are to reduce the time and costs in the development cycle of aircraft engines by a factor of two, reduce production cycle time by a factor of four, and to reduce production costs by 25%. Also, it was the intent of the team to identify the highest impact technologies that could be developed and demonstrated in five years.

Rohn, Douglas A.↗
NASA NTRS1984

Present capabilities and future requirements for computer-aided geometric modeling in the design and manufacture of gas turbine

Gas turbine engine design requires the ability to rapidly develop complex structures which are subject to severe thermal and mechanical operating loads. As in all facets of the aerospace industry, engine designs are constantly driving towards increased performance, higher temperatures, higher speeds, and lower weight. The ability to address such requirements in a relatively short time frame has resulted in a major thrust towards integrated design/analysis/manufacturing systems. These computer driven graphics systems represent a unique challenge, with major payback opportunities if properly conceived, implemented, and applied.

Caille, E.↗
NASA NTRS1999

High Reynolds Number Hybrid Laminar Flow Control (HLFC) Flight Experiment: Suction System Design and Manufacture - Report 4

This document describes the design of the leading edge suction system for flight demonstration of hybrid laminar flow control on the Boeing 757 airplane. The exterior pressures on the wing surface and the required suction quantity and distribution were determined in previous work. A system consisting of porous skin, sub-surface spanwise passages ("flutes"), pressure regulating screens and valves, collection fittings, ducts and a turbocompressor was defined to provide the required suction flow. Provisions were also made for flexible control of suction distribution and quantity for HLFC research purposes. Analysis methods for determining pressure drops and flow for transpiration heating for thermal anti-icing are defined. The control scheme used to observe and modulate suction distribution in flight is described.

Source record↗
NASA NTRS2001

An Assessment of the State-of-the-Art in the Design and Manufacturing of Large Composite Structures for Aerospace Vehicles

An assessment of the State-of-the-Art in the design and manufacturing of large composite structures has been conducted. The focus of the assessment is large structural components in commercial and military aircraft. Applications of composites are reviewed for commercial transport aircraft, general aviation aircraft, rotorcraft, and military aircraft.

Harris, Charles E.↗
NASA NTRS2003

Liner-less Tanks for Space Application - Design and Manufacturing Considerations

Composite pressure vessels, used extensively for gas and fuel containment in space vehicles, are generally constructed with a metallic liner, while the fiber reinforcement carries the major portion of the pressure-induced load. The design is dominated by the liner s low strain at yield since the reinforcing fibers cannot operate at their potential load-bearing capability without resorting to pre-stressing (or autofrettaging). An ultra high-efficiency pressure vessel, which operates at the optimum strain capability of the fibers, can be potentially achieved with a liner-less construction. This paper discusses the design and manufacturing challenges to be overcome in the development of such a pressure vessel. These include: (1) gas/liquid containment and permeation, (2) design and structural analysis, and (3) manufacturing process development. The paper also presents the development and validation tests on a liner-less pressure vessel developed by Kaiser Compositek Inc. (KCI). It should be noted that KCI s liner-less tank exhibits a highly controlled leak-before-burst mode. This feature results in a structure having the highest level of safety.

Jones, Brian H.↗
NASA NTRS1994

Integrated design and manufacturing for the high speed civil transport

In June 1992, the School of Aerospace Engineering at Georgia Tech was awarded a three year NASA University Space Research Association (USRA) Advanced Design Program (ADP) grant to address issues associated with the Integrated Design and Manufacturing of High Speed Civil Transport (HSCT) configurations in its graduate Aerospace Systems Design courses. This report provides an overview of the on-going Georgia Tech initiative to address these design/manufacturing issues during the preliminary design phases of an HSCT concept. The new design methodology presented here has been incorporated in the graduate aerospace design curriculum and is based on the concept of Integrated Product and Process Development (IPPD). The selection of the HSCT as a pilot project was motivated by its potential global transportation payoffs; its technological, environmental, and economic challenges; and its impact on U.S. global competitiveness. This pilot project was the focus of each of the five design courses that form the graduate level aerospace systems design curriculum. This year's main objective was the development of a systematic approach to preliminary design and optimization and its implementation to an HSCT wing/propulsion configuration. The new methodology, based on the Taguchi Parameter Design Optimization Method (PDOM), was established and was used to carry out a parametric study where various feasible alternative configurations were evaluated. The comparison criterion selected for this evaluation was the economic impact of this aircraft, measured in terms of average yield per revenue passenger mile ($/RPM).

Lee, Jae Moon↗
DOE OSTI2020

Manufacturing Process Design of a Micro-Scale Liquid-Liquid Extractor and Multi-phase Separator

Advances in process innovation within the chemical process industry are impeded by the cost of producing new innovative components. In this paper, various manufacturing process routes were evaluated for scaling up a micro-scale liquid-liquid extractor and multi-phase separator capable of separating immiscible phases that are used for the extraction of a chemical product into a lower boiling point solvent to make downstream distillation easier. A manufacturing process design methodology was used to evaluate both photochemical machining and binder jetting as a means for producing the micropost arrays within the separator. Cost curves show that for a 0.3 mm deep micropost array, photochemical machining was found to be much cheaper than binder jetting. However, because binder jetting processes enable microposts with over 13 times higher depth-to-width aspect ratios, binder jetting was found to decrease the overall costs of the extractor/separator by more than half for a 500 barrel per day plant, with breakeven as low as 15 barrels per day. These economics were confirmed by building extractor/separator plates and characterizing them dimensionally and functionally. The binder jet plates were found to perform better than photochemical plates leading to the complete separation of the organic phase from water. The utilization of slower sintering cycles combined with surface grinding provided acceptable dimensional tolerances for the binder jet plates. Using pressurized air during depowdering improved the economics for the binder jetting process.

42 ENGINEERING↗
NASA NTRS2001

An Assessment of the State-of-the-Art in the Design and Manufacturing of Large Composite Structures for Aerospace Vehicles

The results of an assessment of the state-of-the-art in the design and manufacturing of large composite structures are described. The focus of the assessment is on the use of polymeric matrix composite materials for large airframe structural components. such as those in commercial and military aircraft and space transportation vehicles. Applications of composite materials for large commercial transport aircraft, general aviation aircraft, rotorcraft, military aircraft. and unmanned rocket launch vehicles are reviewed. The results of the assessment of the state-of-the-art include a summary of lessons learned, examples of current practice, and an assessment of advanced technologies under development. The results of the assessment conclude with an evaluation of the future technology challenges associated with applications of composite materials to the primary structures of commercial transport aircraft and advanced space transportation vehicles.

Harris, Charles E.↗
DOE OSTI2023

Macroscale Fabrication of Lightweight and Strong Porous Carbon Foams through Template-Coating Pair Design

Manufacturing of low-density-high-strength carbon foams can benefit the construction, transportation, and packaging industries. One successful route to lightweight and mechanically strong carbon foams involves pyrolysis of polymeric architectures, which is inevitably accompanied by drastic volumetric shrinkage (usually >98%). As such, a challenge of these materials lies in maintaining bulk dimensions of building struts that span orders of magnitude difference in length scale from centimeters to nanometers. Here, this work demonstrates fabrication of macroscale low-density-high-strength carbon foams that feature exceptional dimensional stability through pyrolysis of robust template-coating pairs. The template serves as the architectural blueprint and contains strength-imparting properties (e.g., high node density and small strut dimensions); it is composed of a low char-yielding porous polystyrene backbone with a high carbonization-onset temperature. The coating serves to imprint and transcribe the template architecture into pyrolytic carbon; it is composed of a high char-yielding conjugated polymer with a relatively low carbonization-onset temperature. The designed carbonization mismatch enables structural inheritance, while the decomposition mismatch affords hollow struts, minimizing density. The carbons synthesized through this new framework exhibit remarkable dimensional stability (≈80% dimension retention; ≈50% volume retention) and some of the highest specific strengths (≈0.13 GPa g -1 cm 3 ) among reported carbon foams derived from porous polymer templates.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Optimization-based Design for Manufacturing

This report provides detailed documentation of the algorithms that where developed and implemented in the Plato software over the course of the Optimization-based Design for Manufacturing LDRD project.

42 ENGINEERING↗
NASA NTRS2009

Design and Manufacture of Structurally Efficient Tapered Struts

Composite materials offer the potential of weight savings for numerous spacecraft and aircraft applications. A composite strut is just one integral part of the node-to-node system and the optimization of the shut and node assembly is needed to take full advantage of the benefit of composites materials. Lockheed Martin designed and manufactured a very light weight one piece composite tapered strut that is fully representative of a full scale flight article. In addition, the team designed and built a prototype of the node and end fitting system that will effectively integrate and work with the full scale flight articles.

Brewster, Jebediah W.↗