Quantification of local dislocation density using 3D synchrotron monochromatic X-ray microdiffraction
Not Available
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
Explore the source record for details and available documents.
Highlights: • Average GND density is higher in gamma fibre than alpha fibre. • Higher drop in average GND density in un-recrystallized portion of gamma fibre • Fine precipitates pin the grain boundary at 700 °C 0 s. • Precipitates are coarse at 800 °C and present inside strain-free grains. - Abstract: In the present study, cold-rolled low-carbon steel is annealed at three different conditions: 700 °C for 0 s, 800 °C for 0 s and 800 °C for 2 min at the heating rate of ~10 °C/s. Recrystallization behaviour on sample surface is studied using a heated stage Scanning Electron Microscopy and Electron Backscattered Diffraction. For the lower annealing temperature of 700 °C with no dwell, almost no recrystallization is observed and microstructure resembles the as-received deformed material with the exception of occasional sub-micron sized nuclei. For the annealing conditions of 800 °C 0 s and 800 °C 2 min, onset and evolution of recrystallization is observed in-situ as a function of the initial as-cold rolled texture. Slower recovery rate of alpha fibre than gamma fibre is observed and confirmed by lower drop in average geometrically necessary dislocation (GND) density for un-recrystallized alpha fibres (1.1E+14 m{sup −2} for 700 °C 0 s, 1.4E+14 m{sup −2} for 800 °C 0 s and 4.5E+14 m{sup −2} for 800 °C 2 min) than for un-recrystallized gamma fibre grains (3.0E+14 m{sup −2} for 700 °C 0 s, 6.2E+14 m{sup −2} for 800 °C 0 s and 9.8E+14 m{sup −2} for 800 °C 2 min) during annealing. Strong gamma texture in recrystallized matrix is found for annealing conditions of 800 °C 0 s and 800 °C 2 min. From TEM characterisation it was shown that sub-grain boundaries are decorated with fine precipitates (diameter d < 15 nm) of titanium‑vanadium carbides (Ti,V)C for the annealing condition of 700 °C 0 s, which suggests that these precipitates play a major overall role in retardation of the recrystallization kinetics.
Synchrotron White Beam X-ray Topography (SWBXT) studies are presented of basal plane dislocation (BPD) configurations and behavior in a new generation of 100mm diameter, 4H-SiC wafers with extremely low BPD densities (3-4 x 10{sup 2} cm{sup -2}). The conversion of non-screw oriented, glissile BPDs into sessile threading edge dislocations (TEDs) is observed to provide pinning points for the operation of single ended Frank-Read sources. In some regions, once converted TEDs are observed to re-convert back into BPDs in a repetitive process which provides multiple BPD pinning points.
Synchrotron White Beam X-ray Topography (SWBXT) studies are presented of basal plane dislocation (BPD) configurations and behavior in a new generation of 100mm diameter, 4H-SiC wafers with extremely low BPD densities (3-4 x 10{sup 2} cm{sup -2}). The conversion of non-screw oriented, glissile BPDs into sessile threading edge dislocations (TEDs) is observed to provide pinning points for the operation of single ended Frank-Read sources. In some regions, once converted TEDs are observed to re-convert back into BPDs in a repetitive process which provides multiple BPD pinning points.
Synchrotron White Beam X-ray Topography (SWBXT) studies are presented of basal plane dislocation (BPD) configurations and behavior in a new generation of 100mm diameter, 4H-SiC wafers with extremely low BPD densities (3-4 x 10{sup 2} cm{sup -2}). The conversion of non-screw oriented, glissile BPDs into sessile threading edge dislocations (TEDs) is observed to provide pinning points for the operation of single ended Frank-Read sources. In some regions, once converted TEDs are observed to re-convert back into BPDs in a repetitive process which provides multiple BPD pinning points.
Densities of a- and a+c-type threading dislocations for a series of GaN films grown in different modes by metalorganic vapor phase epitaxy are determined from the x-ray diffraction profiles in skew geometry. The reciprocal space maps are also studied. Theory of x-ray scattering from crystals with dislocations is extended in order to take into account contribution from both threading and misfit dislocations. The broadening of the reciprocal space maps along the surface normal and the rotation of the intensity distribution ellipse is attributed to misfit dislocations at the interface. We find that the presence of a sharp AlN/GaN interface leads to an ordering of misfit dislocations and reduces strain inhomogeneity in GaN films.
Models for grain size dependence of flow stress typically ignore contributions from geometrically necessary dislocations (GNDs) in the grain boundary regions. Ashby had proposed the following equation for flow stress (τ) as a function of grain size (d) and effective plastic strain ($\bar{ε}$): $τ = τ_{0} + C'G\sqrt{^{b\bar{ε}}_{d}}$ using an unknown empirical coefficient, C’, In this study, the coefficient, C’, and equation for the grain size dependence of flow stress were investigated in Mg-4Al using nanoindentation. C’ ranges from 1.4 to 7.11 that is related to the hardness difference (∆H0) between the adjacent grains as $C' + 0.62\sqrt{ΔH_{0}}$. Ashby equation was used to predict uniaxial stress-strain curves in grain sizes of 55 µm, 187 µm, and 333 µm. The results showed lower flow stress and lower hardening rate compared to experimentally measured tensile stress-strain response. The discrepancy seems to be a result of hardening effect of SSDs. Here, we propose a modified Ashby equation that takes into account the hardening effect of SSDs and GNDs separately, resulting in a better agreement between calculated and experimentally measured values. This analysis demonstrates estimation of uniaxial stress-strain response using nanoindentation measurements that captures effects of grain size, and strain hardening from SSDs and GNDs. The combination of the revised equation and nanoindentation method will enable rapid exploration of stress-strain response of a diverse range of single-phase polycrystalline alloys.
No abstract prepared.
The influence of microstructural anisotropy on shear response of high-purity titanium was studied using the compact forced-simple-shear specimen (CFSS) loaded under quasi-static loading conditions. Post-mortem characterization reveals significant difference in shear response of different directions in the same material due to material crystallographic texture anisotropy. Shear bands are narrower in specimens in which the shear zone is aligned along the direction with a strong {0001} basal texture. Twinning was identified as an active mechanism to accommodate strains in the shear region in both orientations. This paper confirms the applicability of the CFSS design for the investigation of differences in the shear response of materials as a function of process-induced crystallographic texture. A detailed, systematic approach to quantifying shear band evolution by evaluating geometrically necessary dislocations (GND) associated with crystallographic anisotropy is presented. Finally, the results show that: i) line average GND density profiles, for Ti samples that possess a uniform equiaxed-grain structure, but with strong crystallographic anisotropy, exhibit significant differences in GND density close to the shear band center; ii) GND profiles decrease steadily away from the shear band as the plastic strain diminishes, in agreement with Ashby's theory of work hardening, where the higher GND density in the through-thickness (TT) orientation is a result of restricted < a > type slip in the shear band compared with in-plane (IP) samples; iii) the anisotropy in deformation response is derived from initial crystallographic texture of the materials, where GND density of < a > GNDs are higher adjacent to the shear band in the through-thickness sample oriented away from easy slip, but the density of < c+a > type GNDs are very similar in these two samples; and iv) the increase in grain average GND density was determined to have strong correlation to an increase in the Euler Φ angle of the grain average orientation, indicating an increased misorientation angle evolution.
The dynamic thermomechanical responses of polycrystalline materials under shock loading are often dominated by the interaction of defects and interfaces. For example, within metals, a prescribed deformation associated with a shock wave may be accommodated by crystallographic slip, provided a sufficient population of mobile dislocations is available. However, if the deformation rate is large enough, there may be an insufficient number of freely mobile dislocations. In this case, additional dislocations may be nucleated, or alternate mechanisms (e.g. twinning, damage) activated in order to accommodate the deformation. Furthermore, direct numerical simulation at the mesoscale offers insight into these physical processes that can be invaluable to the development of macroscale constitutive theories, if the mesoscale models adequately represent the anisotropic nonlinear thermomechanical response of individual crystals and their interfaces.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Not Available