Results for “downstream passage” — Page 5

NASA NTRS1956

Contributions on the mechanics of boundary-layer transition

The manner in which flow in a boundary layer becomes turbulent was investigated on a flat plate at wind speeds generally below 100 feet per second. Hot-wire techniques were used, and many of the results are derived from oscillograms of velocity fluctuations in the transition region. Following a presentation of the more familiar aspects of transition, there are presented the very revealing facts discovered while studying the characteristics of artificially produced turbulent spots. These are: (1) oscillograms of natural transition are identical to oscillograms of spot passage; (2) transition starts from perturbations in the laminar flow as spots which then grow in accordance with the general concept proposed by Emmons. (3) Turbulence always moves downstream followed by laminar flow; (4) the following flow is in a state of calm for a period during which transition will not occur.

Schubauer, G B↗

NASA NTRS1982

Observations of mass addition to the shocked solar wind of the Venusian ionosheath

The present investigation constitutes a continuation of a study conducted by Mihalov et al. (1980) concerning the heavy ion component in the plasma observations downstream from Venus, taking into account data obtained with the aid of the plasma analyzer experiment on the Pioneer Venus Orbiter (PVO). The current study is based on analyses of the first season of PVO orbits with apoapsis in the tail and provides clear evidence for the presence of heavy ions. It is found that a heavy ion component was added to the ionosheath flow for a prolonged period on June 8 and 11, 1979 while the spacecraft was downstream from the planet. The heavy ions are identified as oxygen ions O(+). Heavy ions are detected on most of the orbits in the first season or apoapsis tail passages.

Intriligator, D. S.↗

NASA NTRS1986

Lateral jet injection into typical combustor flowfields

The experimental problem of lateral jet injection into typical flow fields in the absence of combustion was studied. All flow fields being investigated have no expansion of the crossflow (the test section to swirler diameter ratio D/d = 1), after its passage through an optional swirler (with swirl vane angle phi = 0 (swirler removed), 45, and 70 degree). The lateral jet(s) is(are) located one test-section diameter downstream of the test-section inlet (x/D = 1). The lateral jets have round-sectioned nozzles, each of which has an area of 1/100th of the cross sectional area of the crossflow (A sub j/A sub c = 1/100). Jet-to-crossflow velocity ratios of R = v sub j/u sub o = 2, 4, and 6 were investigated. Helium-bubble low visualization, five-hole pitot probe time-mean velocity measurements, and single-wire time-mean velocity and normal and shear stress turbulence data were obtained in the research program.

Lilley, D. G.↗

NASA NTRS2005

Making Macroscopic Assemblies of Aligned Carbon Nanotubes

A method of aligning and assembling single-wall carbon nanotubes (SWNTs) to fabricate macroscopic structures has been invented. The method entails suspending SWNTs in a fluid, orienting the SWNTs by use of a magnetic and/or electric field, and then removing the aligned SWNTs from suspension in such a way as to assemble them while maintaining the alignment. SWNTs are essentially tubular extensions of fullerene molecules. It is desirable to assemble aligned SWNTs into macroscopic structures because the common alignment of the SWNTs in such a structure makes it possible to exploit, on a macroscopic scale, the unique mechanical, chemical, and electrical properties that individual oriented SWNTs exhibit at the molecular level. Because of their small size and high electrical conductivity, carbon nanotubes, and especially SWNTs, are useful for making electrical connectors in integrated circuits. Carbon nanotubes can be used as antennas at optical frequencies, and as probes in scanning tunneling microscopes, atomic-force microscopes, and the like. Carbon nanotubes can be used with or instead of carbon black in tires. Carbon nanotubes are useful as supports for catalysts. Ropes of SWNTs are metallic and, as such, are potentially useful in some applications in which electrical conductors are needed - for example, they could be used as additives in formulating electrically conductive paints. Finally, macroscopic assemblies of aligned SWNTs can serve as templates for the growth of more and larger structures of the same type. The great variety of tubular fullerene molecules and of the structures that could be formed by assembling them in various ways precludes a complete description of the present method within the limits of this article. It must suffice to present a typical example of the use of one of many possible variants of the method to form a membrane comprising SWNTs aligned substantially parallel to each other in the membrane plane. The apparatus used in this variant of the method (see figure) includes a reservoir containing SWNTs dispersed in a suspending agent (for example, dimethylformamide) and a reservoir containing a suitable solvent (for example, water mixed with a surfactant). By use of either pressurized gas supplied from upstream or suction from downstream, the suspension of SWNTs and the solvent are forced to mix and flow into a tank. A filter inside the tank contains pores small enough to prevent the passage of most SWNTs, but large enough to allow the passage of molecules of the solvent and suspending agent. The filter is oriented perpendicular to the flow path. A magnetic field parallel to the plane of the filter is applied. The success of the method is based on the tendency of SWNTs to become aligned with their longitudinal axes parallel to an applied magnetic field. The alignment energy of an SWNT increases with the length of the SWNT and the magnetic-field strength. In order to obtain an acceptably small degree of statistical deviation of SWNTs of a given length from alignment with a magnetic field, one must make the field strong enough so that the thermal energy associated with rotation of an SWNT away from alignment is less than the alignment energy.

Smalley, Richard E.↗

NASA NTRSDate not supplied

Effects of Trailing Edge Thickness and Blade Loading Distribution on the Aerodynamic Performance of Simulated CMC Turbine Blades

The aerodynamic performance of three blade sets that represent the geometric manufacturing constraints of Ceramic Matrix Composite (CMC) blades was measured experimentally in a large-scale transonic turbine blade cascade. The trailing edge thicknesses of CMC blades are anticipated to be significantly larger than those of current state-of-the-art metallic blades. The blades tested in the current study had trailing edge thicknesses of 5%, 7%, and 9% relative to the blade axial chord. The three blade sets were designed with matching throat dimensions, so the blade loading distributions were varied to retain similar overall loading levels. Data were acquired at four Reynolds numbers, covering a factor of six range. All data were acquired at the design isentropic exit Mach number of 0.74. Measurements include blade loading and five-hole probe surveys at two downstream stations. The effects of inlet turbulence intensity were also quantified. Total pressure loss data were integrated to determine overall loss levels for each of the three measured blade passages. Excellent periodicity was noted. For low inlet turbulence levels, losses were surprisingly lower for the thickest trailing edge at low Reynolds numbers, but were highest at the maximum Reynolds number. In general, losses were found to scale well with Reynolds number, although front loading was found to significantly reduce the sensitivity of loss to Reynolds number. For high inlet turbulence intensity, losses were found to scale with trailing edge thickness as expected, and the Reynolds number sensitivity was reduced for all three blade sets. Loss levels at the highest Reynolds number were comparable at low and high inlet turbulence intensity levels.

Paul W Giel↗

NASA NTRSDate not supplied

Effects of Trailing Edge Thickness and Blade Loading Distribution on the Aerodynamic Performance of Simulated CMC Turbine Blades

The aerodynamic performance of three blade sets that represent the geometric manufacturing constraints of Ceramic Matrix Composite (CMC) blades was measured experimentally in a large-scale transonic turbine blade cascade. The trailing edge thicknesses of CMC blades are anticipated to be significantly larger than those of current state-of-the-art metallic blades. The blades tested in the current study had trailing edge thicknesses of 5%, 7%, and 9% relative to the blade axial chord. The three blade sets were designed with matching throat dimensions, so the blade loading distributions were varied to retain similar overall loading levels. Data were acquired at four Reynolds numbers, covering a factor of six range. All data were acquired at the design isentropic exit Mach number of 0.74. Measurements include blade loading and five-hole probe surveys at two downstream stations. The effects of inlet turbulence intensity were also quantified. Total pressure loss data were integrated to determine overall loss levels for each of the three measured blade passages. Excellent periodicity was noted. For low inlet turbulence levels, losses were surprisingly lower for the thickest trailing edge at low Reynolds numbers, but were highest at the maximum Reynolds number. In general, losses were found to scale well with Reynolds number, although front loading was found to significantly reduce the sensitivity of loss to Reynolds number. For high inlet turbulence intensity, losses were found to scale with trailing edge thickness as expected, and the Reynolds number sensitivity was reduced for all three blade sets. Loss levels at the highest Reynolds number were comparable at low and high inlet turbulence intensity levels.

Turbine↗

NASA NTRS2014

Aerodynamic Effects of Turbulence Intensity on a Variable-Speed Power-Turbine Blade with Large Incidence and Reynolds Number Variations

The effects of inlet turbulence intensity on the aerodynamic performance of a variable speed power turbine blade are examined over large incidence and Reynolds number ranges. Both high and low turbulence studies were conducted in the NASA Glenn Research Center Transonic Turbine Blade Cascade Facility. The purpose of the low inlet turbulence study was to examine the transitional flow effects that are anticipated at cruise Reynolds numbers. The high turbulence study extends this to LPT-relevant turbulence levels while perhaps sacrificing transitional flow effects. Downstream total pressure and exit angle data were acquired for ten incidence angles ranging from +15.8 to 51.0. For each incidence angle, data were obtained at five flow conditions with the exit Reynolds number ranging from 2.12105 to 2.12106 and at a design exit Mach number of 0.72. In order to achieve the lowest Reynolds number, the exit Mach number was reduced to 0.35 due to facility constraints. The inlet turbulence intensity, Tu, was measured using a single-wire hotwire located 0.415 axial-chord upstream of the blade row. The inlet turbulence levels ranged from 0.25 - 0.4 for the low Tu tests and 8- 15 for the high Tu study. Tu measurements were also made farther upstream so that turbulence decay rates could be calculated as needed for computational inlet boundary conditions. Downstream flow field measurements were obtained using a pneumatic five-hole pitchyaw probe located in a survey plane 7 axial chord aft of the blade trailing edge and covering three blade passages. Blade and endwall static pressures were acquired for each flow condition as well. The blade loading data show that the suction surface separation that was evident at many of the low Tu conditions has been eliminated. At the extreme positive and negative incidence angles, the data show substantial differences in the exit flow field. These differences are attributable to both the higher inlet Tu directly and to the thinner inlet endwall boundary layer that the turbulence grid imposes.

Turbines↗

NASA NTRS2014

Aerodynamic Effects of High Turbulence Intensity on a Variable-Speed Power-Turbine Blade With Large Incidence and Reynolds Number Variations

The effects of high inlet turbulence intensity on the aerodynamic performance of a variable speed power turbine blade are examined over large incidence and Reynolds number ranges. These results are compared to previous measurements made in a low turbulence environment. Both high and low turbulence studies were conducted in the NASA Glenn Research Center Transonic Turbine Blade Cascade Facility. The purpose of the low inlet turbulence study was to examine the transitional flow effects that are anticipated at cruise Reynolds numbers. The current study extends this to LPT-relevant turbulence levels while perhaps sacrificing transitional flow effects. Assessing the effects of turbulence at these large incidence and Reynolds number variations complements the existing database. Downstream total pressure and exit angle data were acquired for 10 incidence angles ranging from +15.8deg to −51.0deg. For each incidence angle, data were obtained at five flow conditions with the exit Reynolds number ranging from 2.12×10(exp 5) to 2.12×10(exp 6) and at a design exit Mach number of 0.72. In order to achieve the lowest Reynolds number, the exit Mach number was reduced to 0.35 due to facility constraints. The inlet turbulence intensity, Tu, was measured using a single-wire hotwire located 0.415 axial-chord upstream of the blade row. The inlet turbulence levels ranged from 8 to 15 percent for the current study. Tu measurements were also made farther upstream so that turbulence decay rates could be calculated as needed for computational inlet boundary conditions. Downstream flow field measurements were obtained using a pneumatic five-hole pitch/yaw probe located in a survey plane 7 percent axial chord aft of the blade trailing edge and covering three blade passages. Blade and endwall static pressures were acquired for each flow condition as well. The blade loading data show that the suction surface separation that was evident at many of the low Tu conditions has been eliminated. At the extreme positive and negative incidence angles, the data show substantial differences in the exit flow field. These differences are attributable to both the higher inlet Tu directly and to the thinner inlet endwall boundary layer that the turbulence grid imposes.

Flegel, Ashlie B.↗

NASA NTRS2014

Aerodynamic Effects of High Turbulence Intensity on a Variable-Speed Power-Turbine Blade with Large Incidence and Reynolds Number Variations

The effects of high inlet turbulence intensity on the aerodynamic performance of a variable speed power turbine blade are examined over large incidence and Reynolds number ranges. These results are compared to previous measurements made in a low turbulence environment. Both high and low turbulence studies were conducted in the NASA Glenn Research Center Transonic Turbine Blade Cascade Facility. The purpose of the low inlet turbulence study was to examine the transitional flow effects that are anticipated at cruise Reynolds numbers. The current study extends this to LPT-relevant turbulence levels while perhaps sacrificing transitional flow effects. Assessing the effects of turbulence at these large incidence and Reynolds number variations complements the existing database. Downstream total pressure and exit angle data were acquired for 10 incidence angles ranging from +15.8deg to −51.0deg. For each incidence angle, data were obtained at five flow conditions with the exit Reynolds number ranging from 2.12×10(exp 5) to 2.12×10(exp 6) and at a design exit Mach number of 0.72. In order to achieve the lowest Reynolds number, the exit Mach number was reduced to 0.35 due to facility constraints. The inlet turbulence intensity, Tu, was measured using a single-wire hotwire located 0.415 axial-chord upstream of the blade row. The inlet turbulence levels ranged from 8 to 15 percent for the current study. Tu measurements were also made farther upstream so that turbulence decay rates could be calculated as needed for computational inlet boundary conditions. Downstream flow field measurements were obtained using a pneumatic five-hole pitch/yaw probe located in a survey plane 7 percent axial chord aft of the blade trailing edge and covering three blade passages. Blade and endwall static pressures were acquired for each flow condition as well. The blade loading data show that the suction surface separation that was evident at many of the low Tu conditions has been eliminated. At the extreme positive and negative incidence angles, the data show substantial differences in the exit flow field. These differences are attributable to both the higher inlet Tu directly and to the thinner inlet endwall boundary layer that the turbulence grid imposes.

Flegel, Ashlie B.↗

NASA NTRS1994

Design and operation of a supersonic annular flow facility

Supersonic annular flow passages exist in propulsion applications that include dual combustion ramjet engines where a supersonic annular flow (the outer flow) mixes with a sonic (or supersonic) gas generator flow (the inner flow) in the shock expansion zone downstream of the gas generator nozzle exit. Other engine designs include components in the form of annular ducts whose cross-sectional area varies in the streamwise flow direction. In some of these configurations, it is necessary to support the outer shroud (cowl) by means of struts positioned between the cowl and centerbody. To investigate the distorting influence of these struts on the local flow structure, it is first necessary to ensure that the intrinsic flow without struts is free of wave reflections and the effects of upstream disturbances. It is also necessary to demonstrate that the intrinsic flow exhibits the characteristics of a well-defined turbulent boundary layer flow, so that changes in the local flow structure induced by the presence of struts can be interpreted properly. The purpose of this Note is to demonstrate that a supersonic flow facility that meets these objectives has been developed.

Williams, K. E.↗

NASA NTRS1993

Navier-Stokes analysis of an oxidizer turbine blade with tip clearance with and without a mini-shroud

The Gas Generator Oxidizer Turbine (GGOT) Blade is being analyzed by various investigators under the NASA MSFC-sponsored Turbine Stage Technology Team design effort. The present work concentrates on the tip clearance region flow and associated losses; however, flow details for the passage region are also obtained in the simulations. The present calculations simulate the rotor blade row in a rotating reference frame with the appropriate coriolis and centrifugal acceleration term included in the momentum equations. The upstream computational boundary is located about one axial chord from the blade leading edge. The boundary conditions at this location have been determined by Pratt & Whitney using an Euler analysis without the vanes to obtain approximately the same flow profiles at the rotor as were obtained with the Euler stage analysis including the vanes. Inflow boundary layer profiles are then constructed assuming the skin friction coefficient at both the hub and the casing. The downstream computational boundary is located about one axial chord from the blade trailing edge, and the circumferentially averaged static pressure at this location was also obtained from the P&W Euler analysis. Results obtained for the 3-D baseline GGOT geometry at the full scale design Reynolds number show a region of high loss in the region near the casing. Particle traces in the near tip region show vortical flow behavior of the fluid which passes through the clearance region and exits at the downstream edge of the gap. In an effort to reduce clearance flow losses, the mini-shroud concept was proposed by the Pratt & Whitney design team. Calculations were performed on the GGO geometry with the mini-shroud. Results of these calculations indicate that the mini-shroud does not significantly affect the flow in the passage region, and although the tip clearance flow is different, the mini-shroud does not seem to prevent the above-mentioned vortical flow behavior. Since both flow distortion and total pressure losses are similar for both geometries, the addition of the mini-shroud does not seem to reduce the tip clearance flow effects.

Chan, Tony↗

NASA NTRS1981

Semi-actuator disk theory for compressor choke flutter

A mathematical anaysis predict the unsteady aerodynamic utilizing semi actuator theory environment for a cascade of airfoils harmonically oscillating in choked flow was developed. A normal shock is located in the blade passage, its position depending on the time dependent geometry, and pressure perturbations of the system. In addition to shock dynamics, the model includes the effect of compressibility, interblade phase lag, and an unsteady flow field upstream and downstream of the cascade. Calculated unsteady aerodynamics were compared with isolated airfoil wind tunnel data, and choke flutter onset boundaries were compared with data from testing of an F100 high pressure compressor stage.

Micklow, J.↗

NASA NTRS2013

Mode Transitions in Hall Effect Thrusters

Mode transitions have been commonly observed in Hall Effect Thruster (HET) operation where a small change in a thruster operating parameter such as discharge voltage, magnetic field or mass flow rate causes the thruster discharge current mean value and oscillation amplitude to increase significantly. Mode transitions in a 6-kW-class HET called the H6 are induced by varying the magnetic field intensity while holding all other operating parameters constant and measurements are acquired with ion saturation probes and ultra-fast imaging. Global and local oscillation modes are identified. In the global mode, the entire discharge channel oscillates in unison and azimuthal perturbations (spokes) are either absent or negligible. Downstream azimuthally spaced probes show no signal delay between each other and are very well correlated to the discharge current signal. In the local mode, signals from the azimuthally spaced probes exhibit a clear delay indicating the passage of "spokes" and are not well correlated to the discharge current. These spokes are localized oscillations propagating in the ExB direction that are typically 10-20% of the mean value. In contrast, the oscillations in the global mode can be 100% of the mean value. The transition between global and local modes occurs at higher relative magnetic field strengths for higher mass flow rates or higher discharge voltages. The thrust is constant through mode transition but the thrust-to-power decreased by 25% due to increasing discharge current. The plume shows significant differences between modes with the global mode significantly brighter in the channel and the near-field plasma plume as well as exhibiting a luminous spike on thruster centerline. Mode transitions provide valuable insight to thruster operation and suggest improved methods for thruster performance characterization.

interplanetary exploration↗

NASA NTRS1976

Heat-Transfer Characteristics of Partially Film Cooled Plug Nozzle on a J-85 Afterburning Turbojet Engine

Plug nozzle film cooling data were obtained downstream of a slot located at 42 percent of the total plug length on a J-85 engine. Film cooling reduced the aft end wall temperature as much as 150 K, reduced total pressure loss in the upstream convection cooling passages by 50 percent, and reduced estimated compressor bleed flow requirement by 14 percent compared to an all convectively cooled nozzle. Shock waves along the plug surface strongly influenced temperature distributions on both convection and film cooled portions. The effect was most severe at nozzle pressure ratios below 10 where adverse pressure gradients were most severe.

Nosek, S. M.↗

NASA NTRS1979

Laser anemometer measurements in a transonic axial flow compressor rotor

A laser anemometer system employing an efficient data acquisition technique was used to make measurements upstream, within, and downstream of the compressor rotor. A fluorescent dye technique allowed measurements within endwall boundary layers. Adjustable laser beam orientation minimized shadowed regions and enabled radial velocity measurements outside of the blade row. The flow phenomena investigated include flow variations from passage to passage, the rotor shock system, three-dimensional flows in the blade wake, and the development of the outer endwall boundary layer. Laser anemometer measurements are compared to a numerical solution of the streamfunction equations and to measurements made with conventional instrumentation.

Strazisar, A. J.↗

NASA NTRS1980

Laser anemometer measurements in a transonic axial flow compressor rotor

A laser anomometer system employing an efficient data acquisition technique has been used to make measurements upstream, within, and downstream of the compressor rotor. A fluorescent dye technique allowed measurements within endwall boundary layers. Adjustable laser beam orientation minimized shadowed regions and enabled radial velocity measurements outside of the blade row. The flow phenomena investigated include flow variations from passage to passage, the rotor shock system, three-dimensional flows in the blade wake, and the development of the outer endwall boundary layer. Laser anemometer measurements are compared to a numerical solution of the streamfunction equations and to measurements made with conventional instrumentation.

Strazisar, A. J.↗

NASA NTRS1993

A numerical analysis of tonal acoustics in rotor-stator interactions

In this study, the unsteady, thin-layer, Navier-Stokes equations are solved using a system of patched grids for a rotor-stator configuration of an axial turbine. The study focuses on the plurality of spinning modes that are present in such an interaction. The propagation of these modes in the upstream and downstream regions is analyzed and compared with numerical results. It was found that the numerically calculated tonal acoustics could be affected by the type of numerical boundary conditions employed at the inlet and exit of the computational boundaries and the grid spacing in the upstream and downstream regions. Results in the form of surface pressure amplitudes and the spectra of turbine tones and their far field behavior are presented. Numerical results and experimental data are compared wherever possible. The 'mode-content' for different harmonics of blade-passage frequency is shown to conform with that predicted by a kinematical analysis.

Rangwalla, A. A.↗

NASA NTRS1985

Vortex generating flow passage design for increased film cooling effectiveness

It is an object of the invention to provide a film cooling apparatus of increased effectiveness and efficiency. In accordance with the invention, a cooling fluid is injected into a hot flowing gas through a passageway in a wall which contains and is subject to the hot gas. The passageway is slanted in a downstream direction at an acute angle to the wall. A cusp shape is provided in the passageway to generate vortices in the injected cooling fluid thereby reducing the energy extracted from the hot gas for that purpose. The cusp shape increases both film cooling effectiveness and wall area coverage. The cusp may be at either the downstream or upstream side of the passageway, the former substantially eliminating flow separation of the cooling fluid from the wall immediately downstream of the passageway.

Papell, S. S.↗