Search NASA⌕ Search

SEARCH · Search NASA

Results for “dry lubricant”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Development and Manufacture of A Proof-of-Concept Magnetically-Geared Actuator for Use in Extremely Cold Lunar Environments

A magnetically-geared actuator is being developed for extremely cold space environments to avoid the wiring and significant efficiency penalty associated with heating grease-lubricated actuators as well as the stringent life and loading constraints imposed by dry film lubricated mechanical gears. This paper describes the lessons learned while designing, manufacturing, and assembling a proof-of-concept prototype similar to the preliminary design of the actuator.

lunar surface↗
NASA NTRSDate not supplied

Design and Hardware Progress on a Magnetically-Geared Actuator for Extremely Cold Lunar Environments

Introduction: Under the Motors for Dusty and Extremely Cold Environments (MDECE) Project, NASA Glenn Research Center is developing a magnetically-geared actuator for extremely cold space environments to avoid the wiring and significant efficiency penalty associated with heating grease-lubricated actuators as well as the stringent life and loading constraints imposed by dry film lubricated mechanical gears. The heating penalty can be equivalent to up to a 90% efficiency reduction in permanently shadowed regions on the Moon. This poster or presentation will summarize the progress made over the past 6-12 months on designing the fully-functional actuator and building a proof-of-concept actuator and testing it in an ambient environment. Design Progress: A critical design review was successfully completed at the end of June 2023. This presentation will touch on the key highlights from that review in the areas of electro-magnetic design and optimization, bearing optimization, thermal analysis, structural analysis, and mechanical design and manufacturing. The predicted technical performance measures of the actuator will be mentioned. The team is currently finishing some actions from the review and finalizing the drawing package in preparation for hardware procurement. Hardware Progress: Despite some significant delays in receiving fabricated parts and magnetic subassemblies, progress was made in manufacturing and assembling a proof-of-concept version of both the actuator’s magnetically-geared motor (Fig. 1) and the actuator’s cycloidal-type output magnetic gear stage (Fig. 2) [3]. The presentation will mention key lessons learned to date from the fabrication, assembly, and testing of the proof of concept.

Lunar surface↗
DOE OSTI2022

Perspectives of 2D MXene Tribology

Abstract The large and rapidly growing family of 2D early transition metal carbides, nitrides, and carbonitrides (MXenes) raises significant interest in the materials science and chemistry of materials communities. Discovered a little more than a decade ago, MXenes have already demonstrated outstanding potential in various applications ranging from energy storage to biology and medicine. The past two years have witnessed increased experimental and theoretical efforts toward studying MXenes’ mechanical and tribological properties when used as lubricant additives, reinforcement phases in composites, or solid lubricant coatings. Although research on the understanding of the friction and wear performance of MXenes under dry and lubricated conditions is still in its early stages, it has experienced rapid growth due to the excellent mechanical properties and chemical reactivities offered by MXenes that make them adaptable to being combined with other materials, thus boosting their tribological performance. In this perspective, the most promising results in the area of MXene tribology are summarized, future important problems to be pursued further are outlined, and methodological recommendations that could be useful for experts as well as newcomers to MXenes research, in particular, to the emerging area of MXene tribology, are provided.

2D materials↗
NASA NTRS1978

Torquing preload in a lubricated bolt

The tension preload obtained by torquing a 7/8 in. diam UNC high strength bolt was determined for lubricated and dry conditions. Consistent preload with a variation of + or - 3% was obtained when the bolt head area was lubricated prior to each torque application. Preload tensions nearly 70% greater than the value predicted with the commonly used formula occurred with the lubricated bolt. A reduction to 39% of the initial preload was observed during 50 torque applications without relubrication. Little evidence of wear was noted after 203 cycles of tightening.

Seegmiller, H. L.↗
NASA NTRS1959

Lubricating Properties of Lead-Monoxide-Base Coatings of Various Compositions at Temperatures to 1250 F

A number of ceramic coatings of different compositions containing lead monoxide (PbO) were studied to determine their relative merits as dry-film lubricants. Lead monoxide is known to be an effective solid lubricant at elevated temperatures, and this oxide was the main component in all compositions studied. Friction and wear properties were determined at temperatures from 750 to 1250 F, at a sliding velocity of 430 feet per minute, and at a normal load of 1 kilogram. In all of the coatings, PbO was the component primarily responsible for the lubricating properties. Oxides other than PbO had an indirect effect on lubrication by influencing such properties as adhesion, hardness, vitrifying or glaze-forming tendency, melting or softening point, and chemical stability of the coatings. Notable among these oxides were magnetite (Fe3O4.), which had generally a beneficial influence on ceramic- to-metal adhesion, and silica (SiO2), which inhibited the oxidation of PbO and enhanced the tendency for glaze formation on the sliding surfaces. Several of the compositions studied provided protection against metal-to-metal adhesive wear, galling, or seizure at test temperatures from 750 to 1250 F. Coating friction coefficients ranged from 0.20 to 0.37 at 75 F but were around 0.08 to 0.20 at temperatures of 1250 F.

Sliney, Harold E.↗
NASA NTRS1978

Graphite-fiber-reinforced polyimide liners of various compositions in plain spherical bearings

Composites made of graphite-fiber-reinforced polyimide (GFRPI) with a fiber-resin ratio (by weight) of about 1 were evaluated as molded outer-race liners in plain spherical bearings. Several compositions were examined: two types of polyimide (addition and condensation polymers), two types of graphite fiber (high and low modulus) and four powder additives (CdO, CdI2, (CF1.1)n, and MoS2). Friction and wear were measured during oscillation at 25, 200, and 315 C. It is shown that all compositions provided good lubrication in dry air, that neither type of polyimide or graphite fiber nor the additives gave a clear advantage, and that wear rates were always higher during run-in, before conditions stabilized. It is concluded that GFRPI composites are self-lubricating under all but the most extreme moisture-free conditions at 25 C. The additives are helpful only with very high loads or extremely dry environments.

Sliney, H. E.↗
NASA NTRS1989

A Spinoff from Mariner

Among the technologies incorporated into the later Mariner missions was a dry film lubricant which offered exceptional lubrication quality for reduced friction and extended wear-life of mating parts in harsh interplanetary environments. Micro Surface Corporation acquired this technology, and currently market it as WS2 modified tungsten disulfide coating. A pressurized refrigerated air application process impinges a dry metallic WS2 coating without heat, curing, binders or adhesives. The coating binds instantly to metal or resin substrates with a 20 millionths of an inch thickness. Performance has been excellent in a variety of industries, particularly in plastics where in some operations, the coating increases production by reducing drag between tool steel and resin. Other advantages include product quality improvement, extension of equipment service life and maintenance elimination or reduction.

Source record↗
NASA NTRS2010

Test Validation of the Repair to the Space Station Solar Alpha Rotary Joint (SARJ)

The SARJ LITE (Lubrication Interval Test) test rig was built as a method to evaluate the performance of the grease repair on the Starboard SARJ of the International Space Station(ISS). The on-orbit SARJ was temporarily parked after receiving significant degradation on one of its race ring nitrided surfaces as a result of inadequate lubrication ( high dry contact friction) and unaccounted for roller traction kinematics. In a scaled down rig, flight like roller bearings were preloaded and cycled on a nitrided 15-5 race surface. Grease was added to the track and with instrumentation monitoring performance, trending data will be extracted and used to determine lubrication intervals for both Port and Starboard ISS SARJ's. The grease lubrication was found to be effective in eliminating the high friction that contributed to the on-orbit race degradation.

Allmon, Curtis↗
NASA NTRS2015

Tribological Evaluation of Candidate Gear Materials Operating Under Light Loads in Highly Humid Conditions

A series of pin-on-disk sliding wear tests were undertaken to identify candidate materials for a pair of lightly loaded timing gears operating under highly humid conditions. The target application involves water purification and thus precludes the use of oil, grease and potentially toxic solid lubricants. The baseline sliding pair is austenitic stainless steel operating against a carbon filled polyimide. The test load and sliding speed (4.9N, 2.7ms) were chosen to represent average contact conditions of the meshing gear teeth. In addition to the baseline materials, the hard superelastic NiTiNOL 60 (60NiTi) was slid against itself, against the baseline polyimide, and against 60NiTi onto which a commercially deposited dry film lubricant (DFL) was applied. The alternate materials were evaluated as potential replacements to achieve a longer wear life and improved dimensional stability for the timing gear application. An attempt was also made to provide solid lubrication to self-mated 60NiTi by rubbing the polyimide against the disk wear track outside the primary 60NiTi-60NiTi contact, a method named stick or transfer-film lubrication. The selected test conditions gave repeatable friction and wear data and smooth sliding surfaces for the baseline materials similar to those in the target application. Friction and wear for self-mated stainless steel were high and erratic. Self-mated 60NiTi gave acceptably low friction (0.2) and modest wear but the sliding surfaces were rough and potentially unsuitable for the gear application. Tests in which 60NiTi pins were slid against DFL coated 60NiTi and DFL coated stainless steel gave low friction and long wear life. The use of stick lubrication via a secondary polyimide pin provided effective transfer film lubrication to self-mated 60NiTi tribological specimens. Using this approach, friction levels were equal or lower than the baseline polyimide-stainless combination and wear was higher but within data scatter observed in these preliminary tests. Based upon these results, self-mated 60NiTi gear teeth utilizing solid lubrication, is a reasonable approach for the target application.

tribology↗
NASA NTRS2015

Tribological Evaluation of Candidate Gear Materials Operating Under Light Loads in Highly Humid Conditions

A series of pin-on-disk sliding wear tests were undertaken to identify candidate materials for a pair of lightly loaded timing gears operating under highly humid conditions. The target application involves water purification and thus precludes the use of oil, grease and potentially toxic solid lubricants. The baseline sliding pair is austenitic stainless steel operating against a carbon filled polyimide. The test load and sliding speed (4.9 N, 2.7 m/s) were chosen to represent average contact conditions of the meshing gear teeth. In addition to the baseline materials, the hard superelastic NiTiNOL 60 (60NiTi) was slid against itself, against the baseline polyimide, and against 60NiTi onto which a commercially deposited dry film lubricant (DFL) was applied. The alternate materials were evaluated as potential replacements to achieve a longer wear life and improved dimensional stability for the timing gear application. An attempt was also made to provide solid lubrication to self-mated 60NiTi by rubbing the polyimide against the disk wear track outside the primary 60NiTi-60NiTi contact, a method named stick or transfer-film lubrication. The selected test conditions gave repeatable friction and wear data and smooth sliding surfaces for the baseline materials similar to those in the target application. Friction and wear for self-mated stainless steel were high and erratic. Self-mated 60NiTi gave acceptably low friction (approx. 0.2) and modest wear but the sliding surfaces were rough and potentially unsuitable for the gear application. Tests in which 60NiTi pins were slid against DFL coated 60NiTi and DFL coated stainless steel gave low friction and long wear life. The use of stick lubrication via the secondary polyimide pin provided effective transfer film lubrication to self-mated 60NiTi tribological specimens. Using this approach, friction levels were equal or lower than the baseline polyimide-stainless combination and wear was higher but within data scatter observed in these preliminary tests. Based upon these results, self-mated 60NiTi gear teeth utilizing solid lubrication, is a reasonable approach for the target application.

tribology↗
NASA NTRS1996

Friction and Wear of Ion-Beam-Deposited Diamondlike Carbon on Chemical-Vapor-Deposited, Fine-Grain Diamond

Friction and wear behavior of ion-beam-deposited diamondlike carbon (DLC) films coated on chemical-vapor-deposited (CVD), fine-grain diamond coatings were examined in ultrahigh vacuum, dry nitrogen, and humid air environments. The DLC films were produced by the direct impact of an ion beam (composed of a 3:17 mixture of Ar and CH4) at ion energies of 1500 and 700 eV and an RF power of 99 W. Sliding friction experiments were conducted with hemispherical CVD diamond pins sliding on four different carbon-base coating systems: DLC films on CVD diamond; DLC films on silicon; as-deposited, fine-grain CVD diamond; and carbon-ion-implanted, fine-grain CVD diamond on silicon. Results indicate that in ultrahigh vacuum the ion-beam-deposited DLC films on fine-grain CVD diamond (similar to the ion-implanted CVD diamond) greatly decrease both the friction and wear of fine-grain CVD diamond films and provide solid lubrication. In dry nitrogen and in humid air, ion-beam-deposited DLC films on fine-grain CVD diamond films also had a low steady-state coefficient of friction and a low wear rate. These tribological performance benefits, coupled with a wider range of coating thicknesses, led to longer endurance life and improved wear resistance for the DLC deposited on fine-grain CVD diamond in comparison to the ion-implanted diamond films. Thus, DLC deposited on fine-grain CVD diamond films can be an effective wear-resistant, lubricating coating regardless of environment.

Miyoshi, Kazuhisa↗
DOE OSTI2026

Irradiation-Induced Structural Disorder and Its Influence on the Mechanical Response of Polycrystalline MoS2

Molybdenum disulfide (MoS2) thin films are widely used as dry-film lubricants and protective coatings in aerospace and other radiation-exposed environments. Conventional synthesis routes produce polycrystalline films whose grain boundaries and other native defects cause their mechanical and tribological behavior to differ substantially from that of ideal single crystals. Under irradiation, these films progressively evolve from polycrystalline structures, composed of layered MoS2 grains, into highly disordered and eventually amorphous structures, altering both their tribological performance and mechanical integrity. Here, we employ reactive atomistic simulations to investigate irradiation-driven structural evolution in bulk polycrystalline MoS2. Using controlled primary knock-on atom (PKA) events, we characterize the progressive transition from a polycrystalline microstructure to an amorphous network by tracking defect accumulation and structural disorder. We then establish how this transition modifies the dominant deformation mechanisms and the temperature-dependent tensile response. Specifically, irradiation suppresses interlayer sliding and delamination, mechanisms which facilitate the deformation of the pristine polycrystal, resulting in defect-induced hardening. Broadly, our results establish direct process–structure–property relationships linking irradiation-induced defect accumulation, microstructural evolution, deformation mechanisms, and mechanical behavior, providing an atomistic framework for understanding the structural integrity and long-term reliability of irradiated MoS2 coatings.

Moore, Daniel [Sandia National Laboratories (SNL)]↗
NASA NTRS1972

Chemical Processing Manual

Chemical processes presented in this document include cleaning, pickling, surface finishes, chemical milling, plating, dry film lubricants, and polishing. All types of chemical processes applicable to aluminum, for example, are to be found in the aluminum alloy section. There is a separate section for each category of metallic alloy plus a section for non-metals, such as plastics. The refractories, super-alloys and titanium, are prime candidates for the space shuttle, therefore, the chemical processes applicable to these alloys are contained in individual sections of this manual.

Beyerle, F. J.↗
NASA NTRS1976

Experiment definition phase shuttle laboratory. LDRL-10.6 experiment

The work completed on the experiment definition phase of the shuttle laboratory LDRL 10.6 micrometers experiment from 27 September 1975 to 26 January 1976 was reported. This work included progress in the following areas: (1) optomechanical system: completion of detail drawings, completion of the beryllium subassembly, fabrication, checking, and weighing of approximately 95% of the detailed parts, dry film lubrication of the bearings and gears, and initiation of assembly of the gimbals; (2) optics: update of the detailed optical layout, receipt of nine mirrors and the pre-expander; (3) miscellaneous: delivery of draft material for the final report, completion of optical testing of the 10.6 micrometers receiver, and receipt, assembly, and checkout of NASA test console.

Source record↗
NASA NTRS2006

JWST NIRSpec Cryogenic Light Shield Mechanism

The focal plane detectors for the Near-Infrared Spectrometer (NIRSpec) instrument on the James Webb Space Telescope (JWST) require a light tight cover for calibration along with an open field-of-view during g round performance testing within a cryogenic dewar. In order to meet the light attenuation requirements and provide open and closed fields of view without breaking vacuum, a light shield mechanism was designe d. This paper describes the details of the light shield mechanism design and test results. Included is information on the labyrinth light p ath design, motor capability and performance, dry film lubrication, m echanism control, and mechanism cryogenic performance results.

Hale, Kathleen↗
NASA NTRS2006

JWST NIRSpec Cryogenic Light Shield Mechanism

The focal plane detectors for the Near-Infrared Spectrometer (NIRSpec) instrument on the James Webb Space Telescope (JWST) require a light tight cover for calibration along with an open field-of-view during ground performance testing within a cryogenic dewar. In order to meet the light attenuation requirements and provide open and closed fields of view without breaking vacuum, a light shield mechanism was designed. This paper describes the details of the light shield mechanism design and test results. Included is information on the labyrinth light path design, motor capability and performance, dry film lubrication, mechanism control, and mechanism cryogenic performance results.

Hale, Kathleen↗
NASA NTRSDate not supplied

High Risk Spacecraft Materials Offgassing

NASA-STD-6001B, Determination of Offgassed Products (Test 7), provides the offgassing characteristics under standardized conditions for materials and assembled articles to be located within habitable spacecraft environments. Experience with Test 7 has found certain material types to be of higher risk for offgassing undesirable compounds aboard spacecraft than others. Formaldehyde and acrolein are historically high T value offgassed components of the offgassed compound target list because they have low spacecraft maximum allowable concentration (SMAC) values assigned by the JSC Toxicology Group. Carbon disulfide, benzene, acrylonitrile, and furan are additional target compounds of concern due to their lower thresholds of toxicity as determined by the JSC Toxicology Group. Materials offgassing siloxanes are also of concern due to their degradation effects on environmental control and life support system (ECLSS) components and performance. Spacecraft materials and articles defined in this manuscript as high risk were identified after examining and condensing data for these compounds of concern from approximately 3000 tests performed over 30 years. Summaries of high risk material and article types based on highest Multi-Purpose Crew Vehicle (MPCV) T values are also presented. Historical analysis shows high risk components are produced largely from test materials and articles in the general categories of electronic/powered components, foams, paints/coatings/films, adhesives/tapes, epoxy/resins, liquids/gels, Nomex® with surface treatments, markers/pens/inks, dry film lubricants, thermoplastics, hygiene items (deodorants, lip balms), and silicone rubber. These data are intended to be a resource for spacecraft materials and processes managers, designers, and toxicologists. High risk materials and articles intended for use aboard spacecraft should be tested in accordance with NASA-STD-6001B Test 7.

Vanessa D Buchanan↗