SEARCH · Search NASA

Results for “embedded boundaries”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Turbulent burst control through phase-locked traveling surface depressions

The influence of a traveling, surface depression on turbulent pre-burst flow has been investigated both theoretically and experimentally. Two-dimensional calculations of a transverse vortex (representing a 'typical' eddy) embedded in a laminar boundary layer show that properly phased-wall motion can reduce vorticity and raise wall pressure beneath the convecting vortex. Experiments in low-speed air with an electromagnetically driven wall membrane show that a traveling wall depression can accelerate flow near the wall and reduce pre-burst Reynolds stress.

Wilkinson, S. P.↗

NASA NTRS1999

Edge-Flames in Von Karman Swirling Flows

Classical understanding of diffusion flames dictates that they, unlike the premixed flames, do not possess a characteristic propagation velocity and are constrained by stoichiometric requirements at the flame surface. However, it has been commonly observed that when local extinction occurs within a diffusion flame sheet, the edges that are formed propagate with distinct speeds. In general, the propagation speed of these edges depend on their geometrical shape (concave, convex, or straight) among other factors. Recently, Buckmaster investigated the dynamics of straight diffusion flame edges separating burning and quenched regions using simplified one-dimensional models. He showed that these flame edges can have positive, negative, or zero velocity depending on the Damkoehler number of the equilibrium diffusion flame that support them. It was also shown that this unsteady flame-edge behavior is intrinsically linked to S-curve behavior of the diffusion flame with varying Damkoehler number. When the system Damkoehler number lies between the extinction and ignition limits, flame edges can propagate as an "ignition wave" or as a "failure wave," and for a critical Damkoehler number remain as a stationary flame-edge. We have extend Buckmaster's 1-d model to more general edge-flame configurations where the edges appear as "flame holes" or as "flame disks". These two configurations along with the straight-edge case cover the entire range of possible edge-flame geometry observable in planar diffusion-flame sheets. A generalized map of edge-flame propagation velocities as a function of the system Damkoehler number and the edge-flame radius is presented. Experimentally we show that edge flames can be created using diffusion flames embedded in von Karman boundary layers. In a von Karman boundary layer, the flow is generated by spinning a solid (fuel) disk in a quiescent ambient gas. Under normal gravity we were able to produce "flame disks" over a range of fuel-disk rotational velocities varying from 0 to 20 revolutions per second, by orienting the burning surface of the fuel disk facing downward.

Nayagam, Vedha↗

NASA NTRS2009

Hybrid Wing Body Configuration System Studies

The objective of this study was to develop a hybrid wing body (HWB) sizing and analysis capability, apply that capability to estimate the fuel burn potential for an HWB concept, and identify associated technology requirements. An advanced tube with wings concept was also developed for comparison purposes. NASA s Flight Optimization System (FLOPS) conceptual aircraft sizing and synthesis software was modified to enable the sizing and analysis of HWB concepts. The noncircular pressurized centerbody of the HWB concept was modeled, and several options were created for defining the outboard wing sections. Weight and drag estimation routines were modified to accommodate the unique aspects of an HWB configuration. The resulting capability was then utilized to model a proprietary Boeing blended wing body (BWB) concept for comparison purposes. FLOPS predicted approximately a 15 percent greater drag, mainly caused by differences in compressibility drag estimation, and approximately a 5 percent greater takeoff gross weight, mainly caused by the additional fuel required, as compared with the Boeing data. Next, a 777-like reference vehicle was modeled in FLOPS and calibrated to published Boeing performance data; the same mission definition was used to size an HWB in FLOPS. Advanced airframe and propulsion technology assumptions were applied to the HWB to develop an estimate for potential fuel burn savings from such a concept. The same technology assumptions, where applicable, were then applied to an advanced tube-with-wings concept. The HWB concept had a 39 percent lower block fuel burn than the reference vehicle and a 12 percent lower block fuel burn than the advanced tube-with-wings configuration. However, this fuel burn advantage is partially derived from assuming the high-risk technology of embedded engines with boundary-layer-ingesting inlets. The HWB concept does have the potential for significantly reduced noise as a result of the shielding advantages that are inherent with an over-body engine installation.

Nickol, Craig L.↗

DOE OSTI2025

Overcoming the conversion reaction limitation at three-phase interfaces using mixed conductors towards energy-dense solid-state Li–S batteries

Lithium–sulfur (Li–S) all-solid-state batteries (ASSBs) hold great promise for next-generation safe, durable and energy-dense battery technology. However, solid-state sulfur conversion reactions are kinetically sluggish and primarily constrained to the restricted three-phase boundary area of sulfur, carbon and solid electrolytes, making it challenging to achieve high sulfur utilization. Here, in this study, we develop and implement mixed ionic–electronic conductors (MIECs) in sulfur cathodes to replace conventional solid electrolytes and invoke conversion reactions at sulfur–MIEC interfaces in addition to traditional three-phase boundaries. Microscopic and tomographic analyses reveal the emergence of mixed-conducting domains embedded in sulfur at sulfur–MIEC boundaries, helping promote the thorough conversion of active sulfur into Li 2 S. Consequently, substantially improved active sulfur ratios (up to 87.3%) and conversion degrees (>94%) are achieved in Li–S ASSBs with high discharge capacity (>1,450 mAh g –1 ) and long cycle life (>1,000 cycles). The strategy is also applied to enhance the active material utilization of other conversion cathodes.

36 MATERIALS SCIENCE↗

NASA NTRS1985

Hybrid approach to steady transonic normal shock-compressible laminar boundary layer interactions over airfoils with suction

Transonic airfoil flow is to a large degree affected by viscous-inviscid interactions. Among them a key role is played by the boundary layer interaction with the shock wave embedded in the flow field and the interaction of the boundary layer with the sustained adverse pressure gradients. The effects of these interactions can be controlled or suppressed by introducing surface mass transfer such as suction. This investigation deals strictly with the study of shock-laminar boundary layer interactions including distributed mass transfer. The present calculations agree with experiments on a swept LFC wing at low speeds which indicates that with a suitable choice of the extent of the airfoil surface over which suction is applied and adjustment of the suction velocity, full-chord laminar flow can be maintained and separation can be prevented completely.

Ram, R. B.↗

NASA NTRS1986

Computation of multi-dimensional viscous supersonic jet flow

A new method has been developed for two- and three-dimensional computations of viscous supersonic flows with embedded subsonic regions adjacent to solid boundaries. The approach employs a reduced form of the Navier-Stokes equations which allows solution as an initial-boundary value problem in space, using an efficient noniterative forward marching algorithm. Numerical instability associated with forward marching algorithms for flows with embedded subsonic regions is avoided by approximation of the reduced form of the Navier-Stokes equations in the subsonic regions of the boundary layers. Supersonic and subsonic portions of the flow field are simultaneously calculated by a consistently split linearized block implicit computational algorithm. The results of computations for a series of test cases relevant to internal supersonic flow is presented and compared with data. Comparison between data and computation are in general excellent thus indicating that the computational technique has great promise as a tool for calculating supersonic flow with embedded subsonic regions. Finally, a User's Manual is presented for the computer code used to perform the calculations.

Kim, Y. N.↗

NASA NTRS2020

Development of a Flow Field for Testing a Boundary-Layer-Ingesting Propulsor

In order to test embedded-propulsor technology, modifications were required of the 8x6 Supersonic Wind tunnel at NASA Glenn Research Center. The extent of the modifications required that a new tunnel calibration be completed to generate a new calibration dataset and operational procedures for the tunnel, as well as to map the boundary layer on the raised floor. This report describes the propulsor inflow that was to be simulated, documents the tunnel modifications that were required, and conveys the results of the calibration test that was completed to measure the resulting flow properties.

boundary layer↗

NASA NTRS1980

Analytic and approximate boundary-fitted coordinate systems for fluid flow simulation

A method for constructing a direct functional relation between the computational and physical domains such that boundaries in the computational domain map into boundaries in the physical domain is presented. This method which is called the 'two-boundary technique' is based on generating functions that represent two disconnected boundaries in the physical domain and an independent function which connects one boundary with another to generate grids. The suggested connecting functions are simple linear and cubic parametric polynomials with parameters based on position and derivatives at the disconnected boundaries. The boundaries can be defined by analytical, approximate, and tension spline functions; the grid density in specified regions is controlled by embedding contraction functions in either the boundary representation or the connecting function.

Smith, R. E.↗

NASA NTRS2013

Recent Development in the CESE Method for the Solution of the Navier-Stokes Equations Using Unstructured Triangular or Tetrahedral Meshes With High Aspect Ratio

In the multidimensional CESE development, triangles and tetrahedra turn out to be the most natural building blocks for 2D and 3D spatial meshes. As such the CESE method is compatible with the simplest unstructured meshes and thus can be easily applied to solve problems with complex geometries. However, because the method uses space-time staggered stencils, solution decoupling may become a real nuisance in applications involving unstructured meshes. In this paper we will describe a simple and general remedy which, according to numerical experiments, has removed any possibility of solution decoupling. Moreover, in a real-world viscous flow simulation near a solid wall, one often encounters a case where a boundary with high curvature or sharp corner is surrounded by triangular/tetrahedral meshes of extremely high aspect ratio (up to 106). For such an extreme case, the spatial projection of a space-time compounded conservation element constructed using the original CESE design may become highly concave and thus its centroid (referred to as a spatial solution point) may lie far outside of the spatial projection. It could even be embedded beyond a solid wall boundary and causes serious numerical difficulties. In this paper we will also present a new procedure for constructing conservation elements and solution elements which effectively overcomes the difficulties associated with the original design. Another difficulty issue which was addressed more recently is the wellknown fact that accuracy of gradient computations involving triangular/tetrahedral grids deteriorates rapidly as the aspect ratio of grid cells increases. The root cause of this difficulty was clearly identified and several remedies to overcome it were found through a rigorous mathematical analysis. However, because of the length of the current paper and the complexity of mathematics involved, this new work will be presented in another paper.

Chang, Sin-Chung↗

NASA NTRS1985

Control plate for shock-boundary layer interaction

Paper describes tests and computations for a relatively unique technique to greatly reduce/eliminate the separation region for shock-boundary layer interactions. A number of studies have shown that the usual effects of such interactions include increased local heating and wall pressures, thickening of the boundary layer and a decrease in the momentum of the flow and, for stronger waves, flow separation. This flow situation is particularly prevalent in supersonic and hypersonic inlets where severe performance degradation can occur due to flow separation. High performance engine design generally requires a uniform entering flow field with little stagnation pressure loss. Previous approaches to the problem involved primarily active devices (e.g., suction or blowing); the present paper considers a passive device. The boundary layer separation control technique considered herein involves the placement of an embedded plate in the outer portion of the boundary layer and parallel to the wall. This control plate is situated such that the incident shock impinges upon and reflects from its surface, thus greatly lessening the pressure gradient in the low momentum near wall region.

Goodman, W. L.↗

DOE OSTI2026

Substrate-Directed Underlayer Growth of Bilayer MoS 2 Revealed by Mo Isotope Labeling

Direct control over the vertical formation sequence and stacking registry in van der Waals (vdW) bilayers is essential for device performance and moiré engineering yet difficult to resolve unambiguously with conventional probes. Here, we use Mo isotope labeling in a two-step chemical vapor deposition process to synthesize bilayer MoS 2 and trace its vertical formation on common substrates. By combining site-selective laser thinning, Raman spectroscopy, time-of-flight secondary ion mass spectrometry, and atomic-resolution scanning transimission electron microscopy (STEM), we find a clear substrate dependence: on SiO 2 /Si, the second layer nucleates and grows beneath the first (underlayer), whereas on sapphire, it forms on top (overlayer). Density functional theory indicates that a larger equilibrium interfacial separation and weaker MoS 2 –substrate interactions on amorphous SiO 2 permit confined interfacial diffusion and underlayer nucleation, whereas stronger interactions and smaller separations on sapphire favor overlayer growth. On SiO 2 , confined epitaxy templates commensurate 2H, 3R, and mixed bilayers, as confirmed by second harmonic generation spectroscopy and STEM. During underlayer coalescence, embedded mirror-twin grain boundaries stitch atomically sharp 2H|3R junctions via alternating 4|8 ring motifs. Molecular-dynamics simulations reveal that these alternating 4|8 motifs accommodate interlayer vdW coupling and locally modulate the stacking registry. These results provide mechanistic insight into confined epitaxial growth and establish isotope labeling as a powerful probe of two-dimensional materials synthesis.

MoS2↗

NASA NTRS1982

Numerical simulation of viscous-inviscid interactions on indented nose tips

An implicit numerical algorithm to solve the unsteady thin-layer Navier-Stokes equations in a strong conservative form has been used to compute the viscous flow over indented nose tips placed in a supersonic free stream. Numerical solutions are presented for axisymmetric and three-dimensional indented configurations for laminar flow conditions. Results demonstrate the capability of the present numerical procedure to predict flow fields that contain strong viscous-inviscid interactions, including boundary-layer separation, reattachment, and embedded discontinuities. Comparisons with available experimental data for the shock shape and surface pressure are also given.

Rizk, Y. M.↗

NASA NTRS1982

A transonic rectangular grid embedded panel method

A method is presented that has the potential for solving transonic flow problems about the same complex aircraft configurations currently being analyzed by subsonic panel methods. This method does not require the generation of surface fitted grids. Instead it uses rectangular grids and subgrids together with embedded surface panels on which boundary conditions are imposed. Both the Euler and full potential equations are considered. The method of least squares is used to reduce the solution of these equations to the solution of a sequence of Poisson problems. The Poisson problems are solved using fast Fourier transforms and panel influence coefficient techniques. The overall method is still in its infancy but some two dimensional results are shown illustrating various key features.

Johnson, F. T.↗

NASA NTRS1986

Application of a computational model for vortex generators in subsonic internal flows

A model for the analysis of vortex generators in a fully viscous subsonic internal flow is evaluated. A vorticity source term is used in a modified form of the Parabolized Navier-Stokes equations to model the shed vortex. Computed results are compared with idealized flow vortex paths, and with experimental data for vortex generators embedded in a thick turbulent boundary layer. The analysis is also compared with experimental data for a separated diffusing S-duct and for a diffusing S-duct with vortex generators. Quantitative comparisons are shown for the latter three cases. Emphasis is placed on verifying the ability of the model to predict global distortions in the flow field.

Kunik, W. G.↗

NASA NTRS1986

Application of a computational model for vortex generators in subsonic internal flows

Kunik, W. G.↗

NASA NTRS1990

Numerical simulation of the incompressible internal flow through a tilting disk valve

A numerical simulation of the incompressible viscous flow through a prosthetic tilting disk heart valve is presented in order to demonstrate the current capability to model unsteady flows with moving boundaries. Both steady and unsteady flow calculations are performed by solving the incompressible Navier-Stokes equations in three-dimensional generalized curvilinear coordinates. In order to handle the moving boundary problems, the chimera grid embedding scheme which decomposes a complex computational domain into several simple subdomains is used. An algebraic turbulence model for internal flows is incorporated to reach the physiological values of Reynolds number. Good agreement is obtained between the numerical results and experimental measurements. It is found that the tilting disk valve causes large regions of separated flow, and regions of high shear.

Chang, I-Dee↗

NASA NTRS1991

Simulation of blood flow through an artificial heart

A numerical simulation of the incompressible viscous flow through a prosthetic tilting disk heart valve is presented in order to demonstrate the current capability to model unsteady flows with moving boundaries. Both steady state and unsteady flow calculations are done by solving the incompressible Navier-Stokes equations in 3-D generalized curvilinear coordinates. In order to handle the moving boundary problems, the chimera grid embedding scheme which decomposes a complex computational domain into several simple subdomains is used. An algebraic turbulence model for internal flows is incorporated to reach the physiological values of Reynolds number. Good agreement is obtained between the numerical results and experimental measurements. It is found that the tilting disk valve causes large regions of separated flow, and regions of high shear.

Kiris, Cetin↗

NASA NTRS1996

Spanwise Spacing Effects on the Initial Structure and Decay of Axial Vortices

The initial structure and axial decay of an array of streamwise vortices embedded in a turbulent pipe boundary layer is experimentally investigated. The vortices are shed in counter-rotating fashion from an array of equally-spaced symmetric airfoil vortex generators. Vortex structure is quantified in terms of crossplane circulation and peak streamwise vorticity. Flow conditions are subsonic and incompressible. The focus of this study is on the effect of the initial spacing between the parent vortex generators. Arrays with vortex generators spaced at 15 and 30 degrees apart are considered. When the spacing between vortex generators is decreased the circulation and peak vorticity of the shed vortices increases. Analysis indicates this strengthening results from regions of fluid acceleration in the vicinity of the vortex generator array. Decreased spacing between the constituent vortices also produces increased rates of circulation and peak vorticity decay.

Wendt, B. J.↗