Search NASA⌕ Search

SEARCH · Search NASA

Results for “fixed boundaries”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Investigation of Aerodynamics Scale Effects for a Generic Fighter Configuration in the National Transonic Facility (Invited)

Two wind tunnel tests of a generic fighter configuration have been completed in the National Transonic Facility. The primary purpose of the tests was to assess Reynolds number scale effects on a thin-wing, fighter-type configuration up to full-scale flight conditions (that is, Reynolds numbers of the order of 60 million). The tests included longitudinal and lateral/directional studies at subsonic and transonic conditions across a range of Reynolds numbers from that available in conventional wind tunnels to flight conditions. Results are presented for three Mach numbers (0.6, 0.8, and 0.9) and three configurations: 1) Fuselage / Wing, 2) Fuselage / Wing / Centerline Vertical Tail / Horizontal Tail, and 3) Fuselage / Wing / Trailing-Edge Extension / Twin Vertical Tails. Reynolds number effects on the lateral-directional aerodynamic characteristics are presented herein, along with longitudinal data demonstrating the effects of fixing the boundary layer transition location for low Reynolds number conditions. In addition, an improved model videogrammetry system and results are discussed.

Tomek, W. G.↗
NASA NTRS1953

Investigation of a Half-Conical Scoop Inlet Mounted at Five Alternate Circumferential Locations around a Circular Fuselage Pressure-Recovery Results at a Mach Number 2.01

The effects of inlet circumferential position around the fuselage on the characteristics of a half-conical scoop inlet having a 24.6deg half-angle cone have been investigated in the langley 4- by 4-foot supersonic pressure tunnel. Pressure-recovery results have been obtained at a Mach number of 2.01 for a fixed boundary-layer-bleed height which was 60 percent of the boundary-layer thickness at an angle of attack of 0deg, and for cowling position parameters of 42.4deg and 38.0deg. inlet had a capture area equal to 24.9 percent of the basic-fuselage frontal area. The angle of attack was varied from 0deg to 12deg. The most favorable pressure-recovery characteristics at angles of attack were obtained with the Inlet located on the bottom of the fuselage where the maximum recovery increased from a value of 81 percent at an angle of attack of 0deg to 87 percent at 12deg. In general, the pressure recovery decreased with increasing angle of attack for all other inlet locations. At a given angle of attack the pressure recovery decreased as the inlet location was progressively moved from the bottom to the top of the fuselage. Stable subcritical operation of the inlet with nearly constant pressure recovery was obtained for inlet mass-flow ratios from 1.0 to about 0.76 at an angle of attack of 0deg with the central body in the design position.

Hasel, Lowell E.↗
NASA NTRS2011

Coupled Elastic-Thermal Dynamics of Deployable Mesh Reflectors

This paper presents a coupled elastic-thermal dynamic model and a quasi-static strategy on the analysis of the reflector dynamics in the space mission. The linearized model, its natural frequencies and mode shapes are then derived upon the nonlinear static equilibrium of the structure. The numerical example is provided to fully adapt the strategy and investigate the dynamic behaviors of the structure. Finally the proposed method is applied on the sample of the deployable mesh reflector and the simulation results are presented. The research work delivered in the paper will be used to design the feedback surface in future.

fixed boundaries↗
NASA NTRS1994

Measurement of Residual Flexibility for Substructures Having Prominent Flexible Interfaces

Verification of a dynamic model of a constrained structure requires a modal survey test of the physical structure and subsequent modification of the model to obtain the best agreement possible with test data. Constrained-boundary or fixed-base testing has historically been the most common approach for verifying constrained mathematical models, since the boundary conditions of the test article are designed to match the actual constraints in service. However, there are difficulties involved with fixed-base testing, in some cases making the approach impractical. It is not possible to conduct a truly fixed-base test due to coupling between the test article and the fixture. In addition, it is often difficult to accurately simulate the actual boundary constraints, and the cost of designing and constructing the fixture may be prohibitive. For use when fixed-base testing proves impractical or undesirable, alternate free-boundary test methods have been investigated, including the residual flexibility technique. The residual flexibility approach has been treated analytically in considerable detail and has had limited frequency response measurements for the method. This concern is well-justified for a number of reasons. First, residual flexibilities are very small numbers, typically on the order of 1.0E-6 in/lb for translational diagonal terms, and orders of magnitude smaller for off-diagonal values. This poses difficulty in obtaining accurate and noise-free measurements, especially for points removed from the excitation source. A second difficulty encountered in residual measurements lies in obtaining a clean residual function in the process of subtracting synthesized modal data from a measured response function. Inaccuracies occur since modes are not subtracted exactly, but only to the accuracy of the curve fits for each mode; these errors are compounded with increasing distance from the excitation point. In this paper, the residual flexibility method is applied to a simple structure in both test and analysis. Measured and predicted residual functions are compared, and regions of poor data in the measured curves are described. It is found that for accurate residual measurements, frequency response functions having prominent stiffness lines in the acceleration/force format are needed. The lack of such stiffness lines increases measurement errors. Interface drive point frequency respose functions for shuttle orbiter payloads exhibit dominant stiffness lines, making the residual test approach a good candidate for payload modal tests when constrained tests are inappropriate. Difficulties in extracting a residual flexibility value from noisy test data are discussed. It is shown that use of a weighted second order least-squares curve fit of the measured residual function allows identification of residual flexibility that compares very well with predictions for the simple structure. This approach also provides an estimate of second order residual mass effects.

Tinker, Michael L.↗
NASA NTRS1991

Numerical recovery of material parameters in Euler-Bernoulli beam models

A fully Sinc-Galerkin method for recovering the spatially varying stiffness parameter in fourth-order time-dependence problems with fixed and cantilever boundary conditions is presented. The forward problems are discretized with a sinc basis in both the spatial and temporal domains. This yields an approximation solution which converges exponentially and is valid on the infinite time interval. When the forward methods are applied to parameter recovery problems, the resulting inverse problems are ill-posed. Tikhonov regularization is applied and the resulting minimization problems are solved via a quasi-Newton/trust region algorithm. The L-curve method is used to determine an appropriate value of the regularization parameter. Numerical results which highlight the method are given for problems with both fixed and cantilever boundary conditions.

Smith, R. C.↗
NASA NTRS1990

A fully Sinc-Galerkin method for Euler-Bernoulli beam models

A fully Sinc-Galerkin method in both space and time is presented for fourth-order time-dependent partial differential equations with fixed and cantilever boundary conditions. The Sinc discretizations for the second-order temporal problem and the fourth-order spatial problems are presented. Alternate formulations for variable parameter fourth-order problems are given which prove to be especially useful when applying the forward techniques to parameter recovery problems. The discrete system which corresponds to the time-dependent partial differential equations of interest are then formulated. Computational issues are discussed and a robust and efficient algorithm for solving the resulting matrix system is outlined. Numerical results which highlight the method are given for problems with both analytic and singular solutions as well as fixed and cantilever boundary conditions.

Smith, R. C.↗
DOE OSTI2020

More of the bulk from extremal area variations

It was shown recently in (Bao N et al 2019 Class. Quantum Grav. 36 185002), building on work of Alexakis, Balehowksy, and Nachman (Alexakis S et al 2017 arXiv:1711.09379), that the geometry of (some portion of) a manifold with boundary is uniquely fixed by the areas of a foliation of two-dimensional disk-shaped surfaces anchored to the boundary. In the context of AdS/CFT, this implies that (a portion of) a four-dimensional bulk geometry can be fixed uniquely from the entanglement entropies of disk-shaped boundary regions, subject to several constraints. Here, we loosen some of these constraints, in particular allowing for the bulk foliation of extremal surfaces to be local and removing the constraint of disk topology; these generalizations ensure uniqueness of more of the deep bulk geometry by allowing for e.g. surfaces anchored on disconnected asymptotic boundaries, or HRT surfaces past a phase transition. We also explore in more depth the generality of the local foliation requirement, showing that even in a highly dynamical geometry like AdS-Vaidya it is satisfied.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS2017

Measured Boundary Layer Transition and Rotor Hover Performance at Model Scale

An experiment involving a Mach-scaled, 11:08 f t: diameter rotor was performed in hover during the summer of 2016 at NASA Langley Research Center. The experiment investigated the hover performance as a function of the laminar to turbulent transition state of the boundary layer, including both natural and fixed transition cases. The boundary layer transition locations were measured on both the upper and lower aerodynamic surfaces simultaneously. The measurements were enabled by recent advances in infrared sensor sensitivity and stability. The infrared thermography measurement technique was enhanced by a paintable blade surface heater, as well as a new high-sensitivity long wave infrared camera. The measured transition locations showed extensive amounts, x=c>0:90, of laminar flow on the lower surface at moderate to high thrust (CT=s > 0:068) for the full blade radius. The upper surface showed large amounts, x=c > 0:50, of laminar flow at the blade tip for low thrust (CT=s < 0:045). The objective of this paper is to provide an experimental data set for comparisons to newly developed and implemented rotor boundary layer transition models in CFD and rotor design tools. The data is expected to be used as part of the AIAA Rotorcraft SimulationWorking Group

Overmeyer, Austin D.↗
DOE OSTI2022

Local atomic environment analysis of short and long-range solute-solute interactions in a symmetric tilt grain boundary

We develop an efficient molecular-statics algorithm for predicting local solute-solute interaction effects on grain-boundary segregation. This algorithm is applied to the segregation and interaction of Ni and Cu solutes in a Σ9 (221) symmetric tilt grain boundary in Ag. It is found that the strength of interaction between two solutes directly correlates with the change of average segregation energy in the local atomic environment of a fixed grain-boundary solute. It is shown that local interaction effects at grain boundaries can be either attractive or repulsive wherein long-range attractive effects increase the propensity for solute cluster nucleation. This study underscores the atomic nature of grain-boundary solute segregation and provides a tool that could yield meaningful insight into heterogeneous solute segregation phenomena in polycrystalline alloys beyond their dilute limit.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A Type II Hamiltonian Variational Principle and Adjoint Systems for Lie Groups

We present a novel Type II variational principle on the cotangent bundle of a Lie group which enforces Type II boundary conditions, i.e., fixed initial position and final momentum. In general, such Type II variational principles are only globally defined on vector spaces or locally defined on general manifolds; however, by left translation, we are able to define this variational principle globally on cotangent bundles of Lie groups. Type II boundary conditions are particularly important for adjoint sensitivity analysis, which is our motivating application. As such, we additionally discuss adjoint systems on Lie groups, their properties, and how they can be used to solve optimization problems subject to dynamics on Lie groups.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1992

Spectral analysis of wave motion in plane solids with boundaries

A spectral formulation is employed whereby in-plane stress waves are synthesized from the superposition of components at discrete frequencies and wavenumbers. The summations are performed using the fast Fourier transform and the Fourier series, respectively. Because the components are discrete, the solution to problems (over the entire field) with completely arbitrary loading, both in time and space, is made tractable. Waves generated from a line load acting on an infinite and semiinfinite plane are first considered. A cascade approach is then adopted for the treatment of these waves incident on a free, fixed, and elastic boundary. At each stage, the results are compared with those obtained from the available classical solutions and/or finite element results. These studies will form the basis for the investigation of in-plane stress waves in multiply layered media.

Rizzi, S. A.↗
NASA NTRS1999

Static Performance of a Fixed-Geometry Exhaust Nozzle Incorporating Porous Cavities for Shock-Boundary Layer Interaction Control

An investigation was conducted in the model preparation area of the Langley 16-Foot Transonic Tunnel to determine the internal performance of a fixed-geometry exhaust nozzle incorporating porous cavities for shock-boundary layer interaction control. Testing was conducted at static conditions using a sub-scale nozzle model with one baseline and 27 porous configurations. For the porous configurations, the effects of percent open porosity, hole diameter, and cavity depth were determined. All tests were conducted with no external flow at nozzle pressure ratios from 1.25 to approximately 9.50. Results indicate that baseline nozzle performance was dominated by unstable, shock-induced, boundary-layer separation at over-expanded conditions. Porous configurations were capable of controlling off-design separation in the nozzle by either alleviating separation or encouraging stable separation of the exhaust flow. The ability of the porous nozzle concept to alternately alleviate separation or encourage stable separation of exhaust flow through shock-boundary layer interaction control offers tremendous off-design performance benefits for fixed-geometry nozzle installations. In addition, the ability to encourage separation on one divergent flap while alleviating it on the other makes it possible to generate thrust vectoring using a fixed-geometry nozzle.

Asbury, Scott C.↗
DOE OSTI2022

Charge carrier motion and effect of fixed oxide charge in a microstructured silicon radiation detector

Signal formation in a microstructured semiconductor neutron detector is more complex than in planar diode geometry. Three-dimensional microstructures are laterally smaller than the ionization cloud length, and the electric fields may be weak enough to exhibit plasma time effects. This work is the first detailed treatment of charge carrier motion in these complex semiconductor devices to replicate the time profile and signal magnitude. Simulations were performed using COMSOL Multiphysics to investigate various parameters that affect the propagation of the charge cloud. It was observed that the size of the simulated three-dimensional structure had an impact on the induced current pulse, indicating the importance of simulation geometry optimization to accurately simulate charge cloud expansion. COMSOL Multiphysics was used to replicate accurate charge creation profiles using energy deposition information imported from radiation transport codes. A detailed simulation methodology is presented to benchmark preamplifier event pulses along with complexities in modeling the charge carrier motion along the etched microstructured trenches with Si–SiO 2 boundary conditions, including fixed oxide charge and interface trapping.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Heisenberg spin chain as a worldsheet coordinate for lightcone quantized string

Although the energy spectrum of the Heisenberg spin chain on a circle defined by H = 1 4 Σ k = 1 M σ k x σ k + 1 x + σ k y σ k + 1 y + Δ σ k z σ k + 1 z is well known for any fixed M, the boundary conditions vary according to whether Mϵ 4N + r, where r = -1,0,1,2, and also according to the parity of the number of overturned spins in the state, In string theory all these cases must be allowed because interactions involve a string with M spins breaking into strings with M 1 < M and M - M 1 spins (or vice versa). We organize the energy spectrum and degeneracies of H in the case Δ = 0 where the system is equivalent to a system of free fermions. In spite of the multiplicity of special cases, in the limit M → ∞ the spectrum is that of a free compactified worldsheet field. Such a field can be interpreted as a compact transverse string coordinate x(σ) ≡ x(σ) + R 0 . We construct the bosonization formulas explicitly in all separate cases, and for each sector give the Virasoro conformal generators in both fermionic and bosonic formulations. Furthermore from calculations in the literature for selected classes of excited states, there is strong evidence that the only change for Δ ≠ 0 is a change in the compactification radius R 0 → R Δ . As Δ→ -1 this radius goes to infinity, giving a concrete example of noncompact space emerging from a discrete dynamical system. Finally we apply our work to construct the three string vertex implied by a string whose bosonic coordinates emerge from this mechanism.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Toroidal modeling of runaway avalanche in DIII-D discharges

Abstract A toroidal modeling tool is developed to study the runaway electron (RE) avalanche production process in tokamak plasmas, by coupling the Rosenbluth–Putvinski avalanche model (Rosenbluth and Putvinski 1997 Nucl. Fusion 37 1355) with an n = 0 magneto-hydrodynamic (MHD) solver. Initial value numerical simulations are carried out for two DIII-D discharges with different plasma shapes (one near circular, and the other with high elongation). It is found that, assuming the same level of about 1% seed current level, the Rosenbluth–Putvinski model somewhat underestimates the RE plateau current for the circular-shaped plasma, as compared with that measured in DIII-D experiments. For an elongated, higher current plasma, simulations find strong runaway current avalanche production despite the lack of measured plateau RE current in experiments. A possible reason for this discrepancy is a lack of additional RE dissipation physics in the present two-dimensional model. Systematic scans of the plasma boundary shape, at fixed pre-disruption plasma current, find that the plasma elongation helps to reduce the RE avalanche production, confirming recent results obtained with an analytic model (Fülöp et al 2020 J. Plasma Phys. 86 474860101). The effect of the plasma triangularity (either positive or negative), on the other hand, has a minor effect. On the physics side, the avalanche process involves two competing mechanisms associated with the electric field. On the one hand, a stronger electric field produces a higher instantaneous avalanche growth rate. On the other hand, a fast growing RE current quickly reduces the fraction of the conduction current together with the electric field, and hence a faster dissipation of the poloidal flux. As a final result of these two dynamic processes, the runaway plateau current is not always the largest with the strongest initial electric field. These results lay the foundation for future self-consistent inclusion of the MHD dynamics and the RE amplification process.

Physics↗
DOE OSTI2021

SCEPTRE 2.2 Angular Quadrature Sets

This document includes details of the angular quadrature sets available in SCEPTRE for performing numerical integrations in the angular phase space. The angular dependence of the boundary and fixed-source terms an d initial angular flux are specified by angular index rather than by direction. It is, therefore, necessary to know the mapping from a specific direction to a direction index. This document includes angular quadrature weights and direction cosines for most of the quadrature sets available in SCEPTRE.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗