Search NASA⌕ Search

SEARCH · Search NASA

Results for “friction data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Use of piezoelectric foil for flow diagnostics

A laboratory investigation was conducted to characterize two piezoelectric-film sensor configurations, a rigidly mounted sensor and a sensor mounted over an air cavity. The sensors are evaluated for sensitivity and frequency response, and methods to optimize data are presented. The cavity-mounted sensor exhibited a superior frequency response and was more sensitive to normal pressure fluctuations and less sensitive to vibrations through the structure. Both configurations were sensitive to large-scale structural vibrations. Flight-test data are shown for cavity-mounted sensors, illustrating practical aspects to consider when designing sensors for application in such harsh environments. The relation of the data to skin friction and maximum shear stress, transition detection, and turbulent viscous layers is derived through analysis of the flight data.

Carraway, Debra L.↗
NASA NTRS1981

Recent Progress Towards Predicting Aircraft Ground Handling Performance

The significant progress which has been achieved in development of aircraft ground handling simulation capability is reviewed and additional improvements in software modeling identified. The problem associated with providing necessary simulator input data for adequate modeling of aircraft tire/runway friction behavior is discussed and efforts to improve this complex model, and hence simulator fidelity, are described. Aircraft braking performance data obtained on several wet runway surfaces is compared to ground vehicle friction measurements and, by use of empirically derived methods, good agreement between actual and estimated aircraft braking friction from ground vehilce data is shown. The performance of a relatively new friction measuring device, the friction tester, showed great promise in providing data applicable to aircraft friction performance. Additional research efforts to improve methods of predicting tire friction performance are discussed including use of an instrumented tire test vehicle to expand the tire friction data bank and a study of surface texture measurement techniques.

Yager, T. J.↗
NASA NTRS1994

The effect of prolonged exposure to 750 C air on the tribological performance of PM212

The effect of prolonged exposure to 750 C air on the tribological performance and dimensional stability of PM212, a high temperature, self-lubricating composite, is studied. PM212, by weight, contains 70 percent metal-bonded Cr3C2, 15 percent BaF2/CaF2 eutectic, and 15 percent silver. Rub blocks were fabricated from PM212 by cold isostatic pressing followed by sintering. Prior to tribo-testing, the rub blocks were exposed to 750 C air for periods ranging from 100 to 1000 hours. Then, the rub blocks were slid against nickel-based superalloy disks in a double-rub-block tribometer in air under a 66 N load at temperatures from 25 to 750 C with a sliding velocity of 0.36 m/s. Unexposed rub blocks were tested for baseline comparison. Friction coefficients ranged from 0.24 to 0.37 for the unexposed rub blocks and from 0.32 to 0.56 for the exposed ones. Wear for both the composite blocks and superalloy disks was typically in the moderate to low range of 10(exp -5) to 10(exp -6) mm(exp 3)/N-m. Friction and wear data were similar for the rub blocks exposed for 100, 500, and 1000 hours. Prolonged exposure to 750 C air increased friction and wear of the PM212 rub blocks at room temperature, but their triboperformance remained unaffected at higher temperatures, probably due to the formation of lubricious metal oxides. Dimensional stability of the composite was studied by exposing specimens of varying thicknesses for 500 hours in air at 750 C. Block thicknesses were found to increase with increased exposure time until steady state was reached after 100 hours of exposure, probably due to oxidation.

Bemis, Kirk↗
NASA NTRS1984

The influence of temperature on the lubricating effectiveness of MoS2 dispersed in mineral oils

The effects of oil viscosity, base oil temperature, and surface-active agents naturally present in mineral oils on the lubricating effectiveness of MoS2 dispersions under boundary lubrication conditions are investigated. Friction and wear data are obtained from tests conducted under a wide range of oil viscosities and operating temperatures. The dispersion temperature at which the friction dropped below that obtained with the base oils, depended upon the base oil viscosity and the concentration of surface-active agents present in the oil. White oils showed reductions in friction before mineral oils of like viscosity, and lower viscosity oils showed reductions in friction before heavier viscosity oils. The results show that for a given base oil, wear increases as temperature increases, while the wear obtained from a MoS2 dispersion made from the base oil remains approximately constant as temperature is increased.

Rolek, R. J.↗
NASA NTRS1993

Modeling fatigue crack growth in cross ply titanium matrix composites

In this study, the fatigue crack growth behavior of fiber bridging matrix cracks in cross-ply SCS-6/Ti-15-3 and SCS-6/Timetal-21S laminates containing center holes was investigated. Experimental observations revealed that matrix cracking was far more extensive and wide spread in the SCS-6/Ti-15-3 laminates compared to that in the SCS-6/Timetal-21S laminates. In addition, the fatigue life of the SCS-6/Ti-15-3 laminates was significantly longer than that of the SCS-6/Timetal-21S laminates. The matrix cracking observed in both material systems was analyzed using a fiber bridging (FB) model which was formulated using the boundary correction factors and weight functions for center hole specimen configurations. A frictional shear stress is assumed in the FB model and was used as a curve fitting parameter to model matrix crack growth data. The higher frictional shear stresses calculated in the SCS-6/Timetal-21S laminates resulted in lower stress intensity factors in the matrix and higher axial stresses in the fibers compared to those in the SCS-6/Ti-15-3 laminates at the same applied stress levels.

Bakuckas, J. G., Jr.↗
NASA NTRS2002

How Surface Treatments Enhance Ground Handling

Several runway surface treatments developed in recent years are described in terms of how aircraft tire landing and takeoff friction requirements are met, particularly during adverse weather conditions. Changing the surface texture with grooving, grinding and shot peening, use of chemicals to remove or prevent accumulation of natural or man-made contaminants, and the use of new techniques and materials are discussed as means of improving surface friction performance. Test data are presented to illustrate the effects of runway conditions on aircraft ground performance. The severity of the problem of operating on runway surfaces which cannot provide sufficient aircraft tire friction capability is also illustrated from documented aircraft accident/incident reports. The paper concludes with recommendations for future pavement research activities.

Yager, Thomas J.↗
NASA NTRS2007

Tribological Performance of PM300 Solid Lubricant Bushings for High Temperature Applications

PM300 is a high temperature solid lubricant material produced through conventional powder metallurgy processing. PM300 is a combination of metal binder (NiCr), hardener (Cr2O3) and lubricant (Ag and BaF2/CaF2) phases and is in commercial use in high temperature furnace conveyors. In this paper, the tribological characteristics of PM300 are evaluated using a newly developed bushing test rig in which PM300 bushings are loaded against rotating steel shafts at temperatures from 25 to 650 C. The data shows that friction and wear are low to moderate and that the lubrication performance (friction) improves with increasing temperature. Several alternative PM300 compositions are evaluated which do not contain silver and are targeted at aircraft gas turbine applications in which environmental compatibility of silver is a concern. It is expected that the data resulting from this research will further the commercialization of this technology.

Striebing, Donald R.↗
NASA NTRS1984

Dynamic Behavior of Spiral-Groove and Rayleigh-Step Self-Acting Face Seals

Tests were performed to determine the dynamic behavior and establish baseline dynamic data for five self-acting face seals employing Rayleigh-step lift-pads and inward pumping as well as outward-pumping spiral grooves for the lift-generating mechanism. The primary parameters measured in the tests were film thickness, seal seat axial motion, and seal frictional torque. The data show the dynamic response of the film thickness to the motion of the seal seat. The inward-pumping spiral-groove seals exhibited a high-amplitude film thickness vibratory mode with a frequency of four times the shaft speed. This mode was not observed in the other seals tested. The tests also revealed that high film thickness vibration amplitude produces considerably higher average film thickness than do low amplitude film thickness vibrations. The seals were tested at a constant face load of 73 N (16.4 lb) with ambient air at room temperature and atmospheric pressure as the fluid medium. The test speed range was from 7000 to 17000 rpm. Seal tangential speed range was 34.5 to 83.7 m/sec (113 to 274 ft/sec).

Dirusso, Eliseo↗
NASA NTRS1983

Surface roughness effects with solid lubricants dispersed in mineral oils

The lubricating effectiveness of solid-lubricant dispersions are investigated in both point and line contacts using surfaces with both random and directional roughness characteristics. Friction and wear data obtained at relatively low speeds and at room temperature, indicate that the existence of solid lubricants such as graphite, MoS2, and PTFE in a plain mineral oil generally will not improve the effectiveness of the oil as a lubricant for such surfaces. Under boundary lubrication conditions, the friction force, as a function of time, initially depends upon the directional roughness properties of the contacting surfaces irrespective of whether the base oil or dispersions are used as lubricants.

Cusano, C.↗
NASA NTRS1960

The Influence of Silicon Additions on Friction and Wear of Nickel Alloys at Temperatures to 1000 Degrees Fahrenheit

Small additions of silicon have considerable beneficial effect on performance on slider alloys. This effect has most frequently been attributed to increased hardness. The research reported was conducted to consider a hypothesis that the primary role of silicon in slider alloys is one of supporting the formation of protective surface films. Friction and wear data were obtained at temperatures from 75 to 1000 degrees Fahrenheit with a series of binary silicon-nickel alloys containing up to 10 percent silicon. Pertinent hot hardness, metallurgical and surface-film analysis data are included. Atmospheres used were air, mixtures of oxygen and argon, a mixture of hydrogen and nitrogen, and a halogenated methane gas lubricant. The results show the role of silicon as a film former to be of great importance in success of silicon-containing alloys as slider materials for extreme temperatures. The range of variables studied gave friction coefficients from 0.05 to greater than 10.00 depending on film formation tendencies. Alloys with 5 percent or more silicon having a duplex structure showed the best results. Film formation resulted from surface reactions or the smearing of the softer phase from the alloys having duplex structure.

Buckley, Donald H.↗
NASA NTRS1950

Influence of tube-entrance configuration on average heat-transfer coefficients and friction factors for air flowing in an Inconel tube

A heat-transfer investigation was conducted with air flowing through an electrically heated Inconel tube having either a long-approach or a right-angle-edge entrance, an inside diameter of 0.402 inch, and a length of 24 inches over a range of Reynolds numbers up to 375,000 and average inside-tube-wall temperatures up to 2000 degrees R. Good correlation of heat-transfer data was obtained for both entrances, which substantiates work previously reported. A fair correlation of friction data was obtained for both entrances. The entrance configuration had little effect on the average heat-transfer and friction coefficients.

HEAT-TRANSFER THEORY AND EXPERIMENT↗
NASA NTRS1971

The attenuation of Love waves and toroidal oscillations of the earth.

An attempt has been made to invert a large set of attenuation data for Love waves and toroidal oscillations in the earth, using a recent method by Backus and Gilbert. The difficulty in finding an acceptable model of internal friction which explains the data, under the assumption that the internal friction is independent of frequency, casts doubt on the validity of this assumption. A frequency-dependent model of internal friction is presented which is in good agreement with the seismic data and with recent experimental measurements of attenuation in rocks.

Jackson, D. D.↗
NASA NTRS1988

Friction-induced ignition of metals in high-pressure oxygen

Data are presented on friction-induced metal ignition (such as occurring as a result of the possible rubbing of oxygen-pressurized hydrostatic bearings and turbine blade tips) in a high-presure oxygen environment. Friction heating tests were carried out at oxygen pressures from 1 to 300 atm and surface speeds from 10 to 33 m/sec, using the NASA/White Sands Test Facility. Test results are presented on the rubbing of like material pairs spanning a wide range of burn factors and on that of dissimilar metal pairs having significantly different burn factors, indicating that the burn factor is a suitable index for rank ordering in ignition resistance for the most, but not all, materials.

Schoenman, Len↗
NASA NTRS1980

Effect of load, area of contact, and contact stress on the wear mechanisms of a bonded solid lubricant film

A pin on disk type of friction and wear apparatus was used to study the effect of load, contact stress and rider area of contact on the friction and wear properties of polyimide bonded graphite fluoride films. Different rider area contacts were obtained by initially generating flats (with areas of 0.0035, 0.0071, 0.0145, and 0.0240 cm) on 0.476-cm radius hemispherically tipped riders. Different projected contact stresses were obtained by applying loads of 2.5- to 58.8-N to the flats. Two film wear mechanisms were observed. The first was found to be a linear function of contact stress and was independent of rider area of contact. The second was found to increase exponentially as the stress increased. The second also appeared to be a function of rider contact area. Wear equations for each mechanism were empirically derived from the experimental data. In general, friction coefficients increased with increasing rider contact area and with sliding duration. This was related to the build up of thick rider transfer films.

Fusaro, R. L.↗
NASA NTRS1981

Effect of load, area of contact, and contact stress on the tribological properties of polyimide bonded graphite fluoride films

A pin-on-disk type of friction and wear apparatus was used to study the effect of load, contact stress and rider area of contact on the friction and wear properties of polyimide-bonded graphite fluoride films. Different rider area contacts were obtained by initially generating flats (with areas of 0.0035, 0.0071, 0.0145, and 0.0240 cm) on 0.476-cm radius hemispherically-tipped riders. Different projected contact stresses were obtained by applying loads of 2.5-to 58.8-N to the flats. Two film wear mechanisms were observed. The first was found to be a linear function of contact stress and was independent of rider area of contact. The second was found to increase exponentially as the stress increased. The second also appeared to be a function of rider contact area. Wear equations for each mechanism were empirically derived from the experimental data. In general, friction coefficients increased with increasing rider contact area and with sliding duration. This was related to the build-up of thick rider transfer films.

Fusaro, R. L.↗
NASA NTRS1973

Compliance measurements.

The uses of compliance measurements in linear fracture mechanics are discussed as a technique for determining the crack-extension force vs load, specimen dimensions, and elastic constants. Some practical examples of application are given, including specimen and transducer descriptions, experimental procedure, instrumentation, calculations, measurement precautions, friction effects, and data reduction. The limitations and advantages of compliance measurements are discussed. It is pointed out that good results can be obtained by the compliance method when its measurement precision is not lower than that required for Young's modulus.

Bubsey, R. T.↗
NASA NTRS1976

On the variation and growth of wave-slope spectra in the capillary-gravity range with increasing wind

A new laser device has been used to make direct wave-slope measurements in the capillary-gravity range. Owing to the design principles, the digital nature of the system and the use of a laser beam as a probe, the earlier problems of intensity variations and meniscus effects were avoided. Using this new technique, wave-slope spectra both down and across the channel were obtained for different wind conditions, along with corresponding mean-square slope values. Comparisons are made with existing data. The results indicate that a quasi-equilibrium state may exist for each wind speed and that it increases in intensity with increasing wind, which may imply an asymptotic nature for the equilibrium-range coefficient. From the data, two significant frictional velocities, 17.5 and 31 cm/s respectively, are identified as critical values for different ranges of wave development.

Long, S. R.↗