Search NASA⌕ Search

SEARCH · Search NASA

Results for “fuel injection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1930

Performance of a High-Speed Compression-Ignition Engine Using Multiple Orifice Fuel Injection Nozzles

This report presents test results obtained at the Langley Memorial Aeronautical Laboratory of the National Advisory Committee for Aeronautics during an investigation to determine the relative performance of a single-cylinder, high-speed, compression-ignition engine when using fuel injection valve nozzles with different numbers, sizes, and directions of round orifices. A spring-loaded, automatic injection valve was used, centrally located at the top of a vertical disk-type combustion chamber formed between horizontally opposed inlet and exhaust valves of a 5 inch by 7 inch engine.

Spanogle, J A↗
NASA NTRS1934

Performance of a Fuel-Injection Spark-Ignition Engine Using a Hydrogenated Safety Fuel

This report presents the performance of a single-cylinder test engine using a hydrogenated safety fuel. The safety fuel has a flash point of 125 degrees f. (Cleveland open-dup method), which is high enough to remove most of the fire hazard, and an octane number of 95, which permits higher compression ratios to be used than are permissible with most undoped gasolines.

Schey, Oscar W↗
DOE OSTI2021

Deep reinforcement learning for dynamic control of fuel injection timing in multi-pulse compression ignition engines

Conventional compression-ignition (CI) engines have long offered high thermal efficiencies and torque across a wide range of loads, but often require extensive exhaust gas treatment that decreases efficiency to meet ever-increasing emissions regulations. One strategy to decrease emissions is to split the fuel injection into a series of smaller injections. In this paper, we explore a new way of discovering optimal control strategies for the next generation of CI engines using deep reinforcement learning (DRL). We outline a DRL procedure to maximize the weighted reward of engine work while minimizing end-of-cycle NO x emissions. Through the procedure outlined in this paper, we show that the DRL agent is able to reduce NO x emissions threefold while only decreasing network by 2%. We demonstrate the use of transfer learning (TL) across hierarchies of physical models to accelerate the learning process, making this approach feasible for a range of control problems within this space. This paper presents a framework and demonstration for using DRL to design control systems in technology areas such as multi-pulse engine control where a hierarchy of models combined with multi-objective rewards are used for optimal operation.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Additive-Mixing Fuel Injection (AMFI): A device for robust control and improved performance of high-efficiency LTGC engines

Low-temperature gasoline combustion (LTGC) engines can provide high efficiencies with very low NOx and particulate emissions. Despite these major advantages, methods for controlling LTGC combustion timing, achieving robust autoignition, and good low-load performance have challenged the development of practical LTGC engines. A key reason is that the ideal reactivity of the fuel varies with operating conditions, with low-reactivity fuels working well at high loads and higher-reactivity fuels working better at low loads. This article introduces a new technique called Additive Mixing Fuel Injection (AMFI) that adjusts the reactivity of the gasoline to obtain good performance over the operating map. Moreover, AMFI can provide robust combustion-timing control because it precisely meters very small amounts (0.01–0.6 mm 3 ) of an ignition-enhancing additive into the fuel each engine cycle. The additive used was 2-ethylhexyl nitrate (EHN), a common, inexpensive diesel-fuel ignition improver, but other additives could be used. Because additive amounts are so small, a 2-gal reservoir would be sufficient for medium-duty applications with refilling only at service intervals of about 8000 mi. The AMFI system has been installed on a single-cylinder LTGC research engine and demonstrated to provide robust combustion-timing control over wide ranges of combustion phasing, fueling rate, intake boost, engine speed, and intake temperature. AMFI also increases the fuel’s reactivity sufficiently to greatly reduce or eliminate the need for charge heating, simplifying engine design and significantly increasing thermal efficiency and the maximum load at low-boost conditions. The nitrogen in the EHN produced a modest increase in NOx, but it was mitigated by lower intake temperatures, and NOx emissions remained very low. Finally, the additive increases the sensitivity of autoignition reactions to variations in the local fuel/air mixture within the charge. This allows the use of controlled fuel stratification for improved LTGC-engine performance, and its potential to improve low-load operation was demonstrated.

Dec, John E.↗
DOE OSTI2021

Oxygenated Fuel Blending Effects in a Mixing-Controlled Compression-Ignition Engine Equipped with Ducted Fuel Injection [Slides]

Continued creation of harmful emissions such as NO x and soot from compression-ignition engines utilizing mixing-controlled combustion systems (i.e., diesel engines) remains a problem and is the subject of on-going research. The inherently high efficiency, relatively low cost, and numerous other desirable attributes of such engines, coupled with a widely supported infrastructure, motivates their continued advancement. Recently, a scientifically distinct and mechanically simple technology called ducted fuel injection (DFI) has shown a robust ability to allow such engines to operate with simultaneously low engine-out soot and NO x emissions when it is employed with simulated exhaust-gas recirculation. To better understand the property ranges of sustainable, oxygenated-fuel blending stocks that will most improve engine performance, two oxygenated blendstocks were separately blended with a commercial diesel base fuel and tested within a heavy-duty diesel optical engine equipped with a four-duct DFI configuration. Conventional and crank-angle-resolved optical diagnostics were used to elucidate the effects of fuel ignition quality, oxygenate molecular structure, and overall oxygen content on engine performance.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1983

Autoignition in a premixing-prevaporizing fuel duct using 3 different fuel injection systems at inlet air temperatures to 1250 K

Conditions were determined in a continuous-flow, premixing-prevaporizing duct at which autoignition occurred. Test conditions were representative of an advanced, regenerative-cycle, automotive gas turbine. The test conditions inlet air temperatures from 600 to 1250 K (a vitiated preheater was used), pressures from 170 to 600 kPa, air velocities of 10 to 30 m/sec, equivalence ratios from 0.3 to 1.0, mixing lengths from 10 to 60 cm, and residence times of 2 to 100 ms. The fuel was diesel number 2. The duct was insulated and had an inside diameter of 12 cm. Three different fuel injection systems were used: One was a single simplex pressure atomizer, and the other two were multiple-source injectors. The data obtained with the simplex and one of the multiple-source injectors agreed satisfactorily with the references and correlated with an Arrenhius expression. The data obtained with the other multiple source injector, which used multiple cones to improve the fuel-air distribution, did not correlate well with residence time.

Tacina, R. R.↗
NASA NTRS1986

A laser-induced-fluorescence visualization study of transverse, sonic fuel injection in a nonreacting supersonic combustor

The present paper reports work which has been conducted in the first phase of a research program which is to provide a data base of spatially-resolved measurements in nonreacting supersonic combustors. In the measurements, a nonintrusive diagnostic technique based on the utilization of laser-induced fluorescence (LIF) is employed. The reported work had the objective to conduct LIF visualization studies of the injection of a simulated fuel into a Mach 2.07 airstream for comparison with corresponding numerical calculations. Attention is given to injection from a single orifice into a constant-area duct, injection from a single orifice behind a rearward-facing step, and injection from staged orifices behind a rearward-facing step.

Mcdaniel, J. C.↗
DOE OSTI2020

Simulation of supersonic molecular beam injection fueling into H-mode plasmas on EAST using BOUT++

Transport dynamic 2D simulations for supersonic molecular beam injection (SMBI) fueling into H-mode deuterium plasmas on the Experimental Advanced Superconducting Tokamak (EAST) is first simulated using a seven-field two-fluid model in the BOUT++ framework. The SMB is assumed to be injected into plasma from the midplane at the low field side with a fixed width and constant molecular flux. The different densities and injection velocities of SMBI are investigated within the upper single-null geometry of EAST. The simulations indicate that the SMBI has a self-shielding effect on molecules' inward transport into the plasma, and the deposition of SMBI leads to a large increase in plasma density and decrease in plasma temperature. There is a velocity threshold for SMB penetrating the pedestal and depositing at the top of density pedestal. However, the deposition point would be back toward the plasma boundary after SMB arriving at the deepest penetration position. Comparing the different molecular injection velocities and densities, the outcomes demonstrate that the depth of deposition is closely related to the injection velocity rather than the molecular density. The simulated results show good agreement with the EAST experiments by comparing the electron density profiles obtained by simulation and experiment, respectively. These results will be helpful for guiding future experiments, as well as the design of the SMBI system.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Ducted fuel injection

Various technologies presented herein relate to heating a fuel and enhancing fuel and charge-gas mixing inside a combustion chamber to enable minimal, or no, generation of soot and/or other undesired emissions during ignition and subsequent combustion of the locally premixed mixtures. To enable sufficient mixing of the fuel and charge-gas, a jet of fuel can be directed to pass through a bore of a duct causing charge-gas to be drawn into the bore creating turbulence to mix the fuel and the drawn charge-gas. The duct can be heated to provision heating of the fuel and charge-gas mixture. The duct can be located proximate to an opening in a tip of a fuel injector. An ignition assist component can be located downstream of the duct to facilitate ignition of the fuel/charge-gas mixture.

42 ENGINEERING↗
NASA NTRS1932

Hydraulics of Fuel-Injection Pumps for Compression-ignition Engines

Formulas are derived for computing the instantaneous pressures delivered by a fuel pump. The first derivation considers the compressibility of the fuel and the second, the compressibility, elasticity, and inertia of the fuel. The second derivation follows that given by Sass; it is shown to be the more accurate of the two. Additional formulas are given for determining the resistance losses in the injection tube. Experimental data are presented in support of the analyses. The report is concluded with an application of the theory to the design of fuel pump injection systems for which sample calculations are included.

Rothrock, A M↗
NASA NTRS1993

Liquid fuel injection elements for rocket engines

Thrust chambers for liquid propellant rocket engines include three principal components. One of these components is an injector which contains a plurality of injection elements to meter the flow of propellants at a predetermined rate, and fuel to oxidizer mixture ratio, to introduce the mixture into the combustion chamber, and to cause them to be atomized within the combustion chamber so that even combustion takes place. Evolving from these injectors are tube injectors. These tube injectors have injection elements for injecting the oxidizer into the combustion chamber. The oxidizer and fuel must be metered at predetermined rates and mixture ratios in order to mix them within the combustion chamber so that combustion takes place smoothly and completely. Hence tube injectors are subject to improvement. An injection element for a liquid propellant rocket engine of the bipropellant type is provided which includes tangential fuel metering orifices, and a plurality of oxidizer tube injection elements whose injection tubes are also provided with tangential oxidizer entry slots and internal reed valves.

Cox, George B., Jr.↗