Search NASA⌕ Search

SEARCH · Search NASA

Results for “graphite microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Thermophysical property and pore structure evolution in stressed and non-stressed neutron irradiated IG-110 nuclear graphite

The nuclear graphite, IG-110, was irradiated with and without a compressive load of 5 MPa at ~400 *C up to 9.3E25 n/m2 (E > 0.1 MeV). Following irradiation physical properties were studied to compare the effect of graphite irradiation on microstructure developed under compression and in stress-free conditions. Properties included: dimensional change, thermal conductivity, dynamic modulus, and CTE. The effect of stress on open internal porosity was determined through nitrogen adsorption. The IG-110 graphite experienced irradiation-induced creep that is differentiated from irradiation-induced swelling. Irradiation under stress resulted in somewhat greater thermal conductivity and coefficient of thermal expansion. While a significant increase in dynamic modulus occurs, no differentiation between materials irradiated with and without compressive stress was observed. Nitrogen adsorption analysis suggests a difference in pore evolution in the 0.3e40 nm range for graphite irradiated with and without stress, but this evolution is seen to be a small contributor to the overall dimensional change.

Snead, Lance↗

Graphitic carbon in the Allende meteorite - A microstructural study

High-resolution transmission electron microscopy shows that carbon in the Allende carbonaceous chondrite meteorite is predominantly a poorly crystalline graphite. Such material is of interest as an important carrier of the isotopically anomalous noble gases found in carbonaceous chondrites.

Smith, P. P. K.↗

Theory and application of laser ultrasonic shear wave birefringence measurements to the determination of microstructure orientation in transversely isotropic, polycrystalline graphite materials

Laser ultrasonic line source methods have been used to study elastic anisotropy in nuclear graphites by measuring shear wave birefringence. Depending on the manufacturing processes used during production, nuclear graphites can exhibit various degrees of material anisotropy related to preferred crystallite orientation and to microcracking. In this paper, laser ultrasonic line source measurements of shear wave birefringence on NBG-25 have been performed to assess elastic anisotropy. Laser line sources allow specific polarizations for shear waves to be transmitted – the corresponding wavespeeds can be used to compute bulk, elastic moduli that serve to quantify anisotropy. These modulus values can be interpreted using physical property models based on orientation distribution coefficients and microcrack-modified, single crystal moduli to represent the combined effects of crystallite orientation and microcracking on material anisotropy. Finally, ultrasonic results are compared to and contrasted with measurements of anisotropy based on the coefficient of thermal expansion to show the relationship of results from these techniques.

36 MATERIALS SCIENCE↗

Characterization of structural defects in nuclear graphite IG-110 and NBG-18

Nuclear graphite IG-110 and NBG-18 were examined using X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscope (SEM) and high resolution transmission electron microscope (HR-TEM) to understand the structure and microstructure of nuclear graphite. The lattice parameter (a), degree of graphitization ( ), crystallite size parallel and perpendicular to c-direction (Lc and L ), anisotropy (B), as well as in-plane crystallite size (La) were calculated and compared based on XRD patterns and Raman spectra. Results indicate that IG-110 has a larger crystallite size and higher degree of graphitization, but lower anisotropy than NBG-18. These differences are attributed to the properties of coke source and manufacturing processes. Additionally, the shape of the pores and crystallized filler particles, the interface between binders and fillers, Mrozowski cracks and nano-cracks, and the defects of disclination were observed and characterized from SEM and HR-TEM images. The similarities and differences in microstructure between IG-110 and NBG-18 are discussed. The results in this work provide useful information to guide selection of nuclear graphite for the design of next generation nuclear plants (NGNP).

99 GENERAL AND MISCELLANEOUS↗

Auger Electrons as Probes for Composite Micro- and Nano- structured Materials: Application to Solid Electrolyte Interphases in Graphite and Silicon-Graphite Electrodes

In this study, Auger electron spectroscopy (AES) combined with ion sputtering profilometry, Xray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM) have been used in a complementary fashion to examine chemical and microstructural changes in graphite (Gr) and silicon/graphite (Si/Gr) blends contained in the negative electrodes of lithium-ion cells. We demonstrate how AES can be used to characterize morphology of the solid-electrolyte interphase (SEI) deposits in such heterogeneous media, complementing well-established methods, such as XPS and SEM. In this way we demonstrate that the SEI does not consist of uniformly thick layers on the graphite and silicon; the thickness of the SEI layers in cycle-life aged electrodes follows an exponential distribution with a mean of ca. 13 nm for the graphite and ca. 20-25 nm for the silicon nanoparticles (with a crystalline core of 50-70 nm in diameter). Furthermore, a “sticky-sphere” model, in which Si nanoparticles are covered with a layer of polymer binder (that is replaced by the SEI during cycling) of variable thickness is introduced to account for the features observed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructure of room temperature ionic liquids at stepped graphite electrodes

Molecular dynamics simulations of room temperature ionic liquid (RTIL) [emim][TFSI] at stepped graphite electrodes were performed to investigate the influence of the thickness of the electrode surface step on the microstructure of interfacial RTILs. A strong correlation was observed between the interfacial RTIL structure and the step thickness in electrode surface as well as the ion size. Specifically, when the step thickness is commensurate with ion size, the interfacial layering of cation/anion is more evident; whereas, the layering tends to be less defined when the step thickness is close to the half of ion size. Furthermore, two-dimensional microstructure of ion layers exhibits different patterns and alignments of counter-ion/co-ion lattice at neutral and charged electrodes. As the cation/anion layering could impose considerable effects on ion diffusion, the detailed information of interfacial RTILs at stepped graphite presented here would help to understand the molecular mechanism of RTIL-electrode interfaces in supercapacitors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Beyond the classical kinetic model for chronic graphite oxidation by moisture in high temperature gas-cooled reactors

Four grades of nuclear graphite with various microstructures were subjected to accelerated oxidation tests in helium with traces of moisture and hydrogen in order to evaluate the effects of chronic oxidation on graphite components in high temperature gas cooled reactors. Kinetic analysis showed that the Langmuir-Hinshelwood (LH) model cannot consistently reproduce all results. In particular, at high temperatures and water partial pressures oxidation was always faster than the LH model predicts, with stronger deviations for superfine grain graphite than for medium grain grades. It was also found empirically that the apparent reaction order for water has a sigmoid-type variation with temperature which follows the integral Boltzmann distribution function. This suggests that the apparent activation with temperature of graphite reactive sites that causes deviations from the LH model is rooted in specific structural and electronic properties of surface sites on graphite. A semi-global kinetic model was proposed, whereby the classical LH model was modified with a temperature-dependent reaction order for water. The new Boltzmann-enhanced model (BLH) was shown to consistently predict experimental oxidation rates over large ranges of temperature (800-1100 oC) and partial pressures of water (3-1200 Pa) and hydrogen (0-300 Pa), not only for the four grades of graphite but also for the historic grade H-451. The BLH model offers as more reliable input for modeling the chemical environment effects during the life-time operation of new grades of graphite in advanced nuclear reactors operating at high and very high temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Protection of graphite from salt and gas permeation in molten salt reactors

The reactor core, moderator and reflectors of a thermal spectrum advanced molten salt reactor will constitute multi-tons of graphite. Porous reactor-grade graphite, if unprotected, can be permeated by molten salt depending on the infiltrating pressure differential and entrance diameters of accessible graphite pores. Salt and gas permeation of graphite can affect microstructural properties and radiation behavior but also facilitate diffusion, deposition and retention of fission products and tritium. Because of the significant void volume of nuclear graphite, fission products and tritium retention due to salt permeation necessitates seal coatings or pore impregnation to reduce open porosity. Alternatively, very fine-grained graphite grades with low Xe permeability are being developed. In this work, we survey the current technologies for mitigating salt and gas transport into graphite.

36 MATERIALS SCIENCE↗

Proton irradiated graphite grades for a long baseline neutrino facility experiment

In search of a low-Z pion production target for the Long Baseline Neutrino Facility (LBNF) of the Deep Underground Neutrino Experiment (DUNE) four graphite grades were irradiated with protons in the energy range of 140–180 MeV, to peak fluence of ~6.1×10 20 p/cm 2 and irradiation temperatures between 120–200 °C. The test array included POCO ZXF-5Q, Toyo-Tanso IG 430, Carbone-Lorraine 2020 and SGL R7650 grades of graphite. Irradiation was performed at the Brookhaven Linear Isotope Producer. Postirradiation analyses were performed with the objective of (a) comparing their response under the postulated irradiation conditions to guide a graphite grade selection for use as a pion target and (b) understanding changes in physical and mechanical properties as well as microstructure that occurred as a result of the achieved fluence and in particular at this low-temperature regime where pion graphite targets are expected to operate. A further goal of the postirradiation evaluation was to establish a proton-neutron correlation damage on graphite that will allow for the use of a wealth of available neutron-based damage data in proton-based studies and applications. Macroscopic postirradiation analyses as well as energy dispersive x-ray diffraction of 200 KeV x rays at the NSLS synchrotron of Brookhaven National Laboratory were employed. The macroscopic analyses revealed differences in the physical and strength properties of the four grades with behavior however under proton irradiation that qualitatively agrees with that reported for graphite under neutrons for the same low temperature regime and in particular the increase of thermal expansion, strength and Young’s modulus. The proton fluence level of ~10 20 cm -2 where strength reaches a maximum before it begins to decrease at higher fluences has been identified and it agrees with neutron-induced changes. X-ray diffraction analyses of the proton irradiated graphite revealed for the first time the similarity in microstructural graphite behavior to that under neutron irradiation and the agreement between the fluence threshold of ~5×10 20 cm -2 where the graphite lattice undergoes a dramatic change. The confirmed similarity in behavior and agreement in threshold fluences for proton and neutron irradiation effects on graphite reported for the first time in this study will enable the safe utilization of the wealth of neutron irradiation data on graphite that extends to much higher fluences and different temperature regimes by the proton accelerator community searching for multi-MW graphite targets.

43 PARTICLE ACCELERATORS↗

Microstructure-derived macroscopic residual resistance of brominated graphite fibers

The microscopic bromine distribution in pitch-based brominated graphite fibers has been measured with a scanning transmission electron microscope by monitoring the Br K alpha1 X-ray intensity. An imhomogeneous distribution of Br along the fiber is found with two distinct cross-sectional distributions, namely, a uniform distribution in Br-rich regions and a Gaussian-like distribution in Br-poor regions. A model based on these Br distribution measurements is proposed to understand the relation between the Br microstructure and the macroscopic residual resistance of the fiber. This model yields semiquantitative agreement with experimental results.

Qian, X. W.↗

Size Distribution of Graphite Nodules in Hypereutectic Cast Irons of Varying Nodularity

An SGI was machined into 400 g cylindrical pieces and remelted in an electrical resistance furnace protected by Ar gas to produce materials ranging from SGI to CGI. The graphite morphology was controlled by varying the holding time at 1723 K (1450 °C) between 10 and 60 minutes. The discrete sectional size distribution of nodules by number density was measured on cross sections of the specimens and translated to volumetric distribution by volume fraction. Subpopulations of nodules were distinguished by fitting Gaussian distribution functions to the measured distribution. Primary and eutectic graphite, were found to account for most of the volume of nodular graphite in all cases. For holding times of 40 minutes and greater, corresponding to nodularity roughly below 40 pct, the primary subpopulation was very small and difficult to distinguish, leaving eutectic nodules as the dominant subpopulation. The mode and standard deviation of the two subpopulations were roughly independent of nodularity. Moreover, the nodular and vermicular graphite were segregated in the microstructure. In conclusion, the results suggest that the parallel development of the vermicular eutectic had small influence on the size distribution of eutectic graphite nodules.

36 MATERIALS SCIENCE↗

Macro-scale Testing and Micromechanics Modeling of Fracture Behaviors for Boron Carbide Composites with Hierarchical Microstructures

With a unique combination of properties including high hardness, low density, wear and corrosion resistance, thermal stability, high neutron absorption, and semi-conductivity, boron carbide (B4C) is a candidate material for various engineering applications that involve extreme environment. The current applications of boron carbide, however, are limited by its intrinsic brittleness due to its strong covalent bonding. To toughen boron carbide, in this work hierarchical microstructure designs was used to provide multiple toughening mechanisms including crack deflection/bridging, micro-crack toughening, etc. Using field assisted sintering, B4C composites with hierarchical microstructure features including graphite platelets, micron and sub-micron sized TiB2 reinforcements were fabricated. The fracture toughness of fabricated B4C composites were previously measured at micro-scale using micro-indentation followed by post-testing microstructure inspection. However, questions including whether the fracture toughness enhancement measured at micro-scale can translate to macro-scale mechanical properties, and what are the fundamental mechanisms behind observed fracture toughness enhancement, remain to be answered. In this study, the fabricated B4C composites were tested using standardized four-point bending method to obtain fracture toughness at macro-scale. In addition, micromechanics modeling was conducted using MAC/GMC code and crack-band model to study the effect of residual stress and weak interphases on fracture behaviors of B4C composites reinforced with TiB2 particles. Through standardized four-point bending tests, fracture toughness enhancements up to 2.85, 3.32, and 3.65 MPa∙m(exp 1/2) (from 2.38 MPa∙m(exp 1/2)) were achieved for B4C composites with graphite platelets addition (micro/nano B4C), with TiB2 formation (micro B4C-TiB2), and with both graphite and TiB2 addition (micro/nano B4C-TiB2) respectively. Micromechanics modeling indicated that introduction of thermal residual stress and weak interphases caused enhanced micro-cracking behavior and resulted in the observed fracture toughness enhancement. These results furthered understanding about the mechanical behaviors at macro-scale and the mechanisms behind observed fracture toughness enhancement for B4C composites with hierarchical microstructures and can provide reference data for the future design of B4C composites with optimized microstructures for further fracture toughness enhancement.

Boron Carbide↗

A Review of Finite Element Method Models for Nuclear Graphite Applications

Graphite components serve as structural support and as a neutron moderator in multiple nuclear power stations and is also a prospective material in Generation IV reactor concepts. The environment (e.g. high temperature and intense radiation) within a graphite core changes the geometry, microstructure and material properties of the graphite components, that could limit the lifetime (i.e. safe operation) of a reactor. Some of the assessments made for graphite reactor core components include Finite Element Method (FEM) simulations. These simulations are used to estimate the stress state and strain state and probability of failure of irradiated graphite components. FEM also forms part of the validation of measurements or as a complementary technique to experimental procedures in graphite research. A comprehensive overview of FEM methodologies is provided in this review, including: FEM software, basics steps to set up a FEM model, and analytical solutions used to validate simulations for this field of study. In conclusion, the objective of this paper is to inform researchers in the different available FEM techniques and tools used in the research of nuclear graphite.

42 ENGINEERING↗

Study of Tritium Transport in Nuclear-Grade Graphite and Molten Fluoride Salt Systems

High-temperature salts are proposed as coolant in recent reactor technologies including Fluoride Salt-Cooled High Temperature Reactor (FHR) with fluoride salt as primary and secondary loop coolant, Molten Salt Reactors (MSRs) with fuel salt, and high-magnetic-field fusion machines with salt coolant blanket. The baseline coolant is {sup 7}Li{sub 2}BeF{sub 4} (flibe) due to its good thermal-hydraulic and neutronic properties. Tritium produced in flibe due to neutron irradiation makes the issue of tritium transport an area of great interest. In the temperature range of 427- 704 deg. C, tritium readily diffuses through metallic reactor structural materials, which makes tritium control and capture a key technical challenge. It is anticipated that tritium can be captured by graphite, as graphite material showed a high affinity for tritium in the Molten Salt Reactor Experiment (MSRE) due to the porous and irregular crystallite microstructure. Two types of nuclear grade graphite which used as core components for FHR: matrix graphite, which encapsulates the TRISO (Tri-structural-isotropic) fuel particles in FHR, and high purity, isotropic nuclear grade graphite IG-110 which can be used as moderator and reflector in reactor core for both fission and fusion reactor. The microstructure of matrix graphite and IG-110 is different from that of matrix graphite, due to the raw material and manufacturing processes. There are three phenomena important for predicting tritium transport in graphite-salt systems: tritium species diffusion in molten flibe; tritium species transport at the salt-graphite interface; and tritium species transport in graphite. In this summary microstructure characterization of IG-110 and matrix graphite, characterization of graphite-salt interface as well as techniques for trace tritium detection in graphite are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗