Search NASA⌕ Search

SEARCH · Search NASA

Results for “gyro data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

High resolution angular sensor

Specifications for the pointing stabilization system of the large space telescope were used in an investigation of the feasibility of reducing ring laser gyro output quantization to the sub-arc-second level by the use of phase locked loops and associated electronics. Systems analysis procedures are discussed and a multioscillator laser gyro model is presented along with data on the oscillator noise. It is shown that a second order closed loop can meet the measurement noise requirements when the loop gain and time constant of the loop filter are appropriately chosen. The preliminary electrical design is discussed from the standpoint of circuit tradeoff considerations. Analog, digital, and hybrid designs are given and their applicability to the high resolution sensor is examined. the electrical design choice of a system configuration is detailed. The design and operation of the various modules is considered and system block diagrams are included. Phase 1 and 2 test results using the multioscillator laser gyro are included.

Gneses, M. I.↗
NASA NTRSDate not supplied

Swift Mission Gyro Patch and Re-Calibration Without A Calibration Campaign

The Swift spacecraft has three Two-Axis-Rate-Assemblies (TARAs) (designated as TARA 1, TARA 2, and TARA 3, and generically referred to as gyros) which until March of 2024 were all used in rate estimation as an operational workaround (dubbed “corrector-gyro”) of a software defect discovered in 2007. TARA 1 performance degraded throughout 2023 and 2024, making it an unreliable rate source. It was determined that shifting TARA 1 to be the corrector-gyro and using mainly TARAs 2 and 3, with the existing flight software (FSW) defect, would not meet performance requirements for science operations. Rather the FSW was patched to remove the defect found in 2007. This patch was delivered by the vendor in 2009, but was not fully tested or installed at that time. A decision was made in 2024 to install the patch despite limited simulation and testing capabilities. The problem facing the team was to come up with a set of alignment parameters that would work with the new patch, using data from the spacecraft operating normally in the old configuration. Calibration activities would have been possible in either the old or new FSW configuration, but were ultimately deemed unnecessary, saving staff time and pre-serving time on the spacecraft for science data collection. This paper describes the old and new FSW configurations related to gyro processing and alignment, and how the raw gyro and star tracker data from normal operation were used with a multidimensional unconstrained nonlinear minimization in MATLAB (Nelder-Mead1) to produce a fully calibrated set of gyro alignment parameters compatible with the patched FSW. Flight data is presented showing that not only did the process work, it improved performance significantly, rivaling the best slew performance of the mission to date.

MATLAB↗
NASA NTRS1977

In-flight gyro drift rate calibration on the Viking Orbiters

The drift rates of the attitude control gyros onboard the Viking Orbiters were calibrated several times during flight. The calibration was performed by engaging the gyro control of attitude for a six-hour period, recording the Viking Orbiter coordinates of the sun and the roll reference star as a function of time, and processing these data by a computer program. The computer program calculated drift rates for each data increment, and then smoothed the calculated rate versus the time function for all the data on the basis of a Gauss-Markov gyro-drift model. The effects of data noise were minimized by using a relatively long time constant in the Gauss-Markov model and by empirically determining a set of corrections for celestial inertial scale factor error differences. In this way the rms error of the data fit was lessened.

Breckenridge, W. G.↗
NASA NTRS1985

Numerical and experimental evaluation for single-axis control of an LSS laboratory model

One of the major problems of LSS attitude control design stems from the modeling uncertainties due to modal truncation errors and modal parameter estimation errors. This modeling problem is investigated by evaluating poles and zeros of the frequency response functions, described in terms of constrained or unconstrained modes. The frequency domain approach is utilized to evaluated the results of modal analyses and direct output feedback controller experiments using a simple flexible spacecraft model consisting of a rigid primary body and flexible aluminum beam(s) with a control moment gyro as an actuator. The modal data are compared under the conditions that the model is constrained as the canti-lever and it is rotationally free on a single-axis air bearing table. In addition, the open-loop responses are experimentally examined under the impulsive disturbance to the appendage. The results of the control experiments show that the first vibration mode of the appendage and the interacted rotational motion of the primary body are damped in a short time as predicted by the numerical analysis, to produce damping ratio of 10-20%.

Ohkami, Y.↗
NASA NTRS1990

A preliminary look at techniques used to obtain airdata from flight at high angles of attack

Flight research at high angles of attack has posed new problems for airdata measurements. New sensors and techniques for measuring the standard airdata quantities of static pressure, dynamic pressure, angle of attack, and angle of sideslip were subsequently developed. The ongoing airdata research supporting NASA's F-18 high alpha research program is updated. Included are the techniques used and the preliminary results. The F-18 aircraft was flown with three research airdata systems: a standard airdata probe on the right wingtip, a self-aligning airdata probe on the left wingtip, and a flush airdata system on the nose cone. The primary research goal was to obtain steady-state calibrations for each airdata system up to an angle of attack of 50 deg. This goal was accomplished and preliminary accuracies of the three airdata systems were assessed and are presented. An effort to improve the fidelity of the airdata measurements during dynamic maneuvering is also discussed. This involved enhancement of the aerodynamic data with data obtained from linear accelerometers, rate gyros, and attitude gyros. Preliminary results of this technique are presented.

Moes, Timothy R.↗
NASA NTRS1996

Development and Utility of a Four-Channel Scanner for Wildland Fire Research and Applications

The Airborne Infrared Disaster Assessment System (AIRDAS) is a four-channel scanner designed and built at NASA-Ames for the specific task of supporting research and applications on fire impacts on terrestrial and atmospheric processes and also of serving as a vital instrument in the assessment of natural and man-induced disasters. The system has been flown on numerous airframes including the Navajo, King-Air, C0130, and Lear Jet 310 and a 206. The system includes a configuration composed of a 386 PC computer workstation, a non-linear detector amplifier, a sixteen-bit digitizer, dichroic filters, and Exabyte 8500 5Gb Tape output, VHS tape output, a Rockwell GPS and a 2-axis gyro. The AIRDAS system collects digital data in four wavelength regions, which can be filtered: band 1 (0.61-0.68 microns), band 2 (1.57-1.7 microns), band 3 (3.6-5.5 microns), and band 4 (5.5-13.0 microns), an FOV of 108 degrees, an IFOV of 2.62 mrads, and a digitized swath width of 720 pixels. The inclusion of the non-linear detector amplifier allows for the accurate measurement of emitted temperature from fires and hot spots. Lab testing of the scanner has indicated temperature assessments of 800 C without detector saturation. This has advantages over previous systems which were designed for thermal measurement of earth background temperatures, and were ill-equipped for accurate determination of high intensity conditions. The scanner has been flown successfully on data collection missions since 1992 in the western US as well as Brazil. These and other research and applications responses will be presented along with an assessment of future directions with the system.a

Ambrosia, Vincent G.↗
NASA NTRS2007

Attitude Sensor and Gyro Calibration for Messenger

The Redundant Inertial Measurement Unit Attitude Determination/Calibration (RADICAL(TM)) filter was used to estimate star tracker and gyro calibration parameters using MESSENGER telemetry data from three calibration events. We present an overview of the MESSENGER attitude sensors and their configuration is given, the calibration maneuvers are described, the results are compared with previous calibrations, and variations and trends in the estimated calibration parameters are examined. The warm restart and covariance bump features of the RADICAL(TM) filter were used to estimate calibration parameters from two disjoint telemetry streams. Results show that the calibration parameters converge faster with much less transient variation during convergence than when the filter is cold-started at the start of each telemetry stream.

O'Shaughnessy, Daniel↗
NASA NTRS2018

High Fidelity Reconstructed Attitude Estimation Using Cassini Flight Telemetry

The Cassini Grand Finale capped the 20 year Cassini mission with 22 one-week-long orbits each with periapsis inside the ring plane just above Saturn’s cloud tops. One aspect of these remarkable orbits was unprecedented measurements of Saturn’s magnetic field very close to the planet. Processing this data required precise estimates of Cassini’s orientation during these ring plane crossings. These periods coincided with planned gyro-only attitude propagation due to the enormous bright bodies in the star tracker field-of-view. This paper describes how attitude reacquisition information, when the star tracker reacquires an absolute inertial reference, can be used to correct errors introduced during gyro-only propagation. The resulting high fidelity reconstruction significantly improves the extraction of Saturn’s magnetic field from the raw data obtained during gyro-only periods when Cassini’s changing orientation makes precise attitude estimation a challenge.

Burk, Thomas A.↗
NASA NTRS1988

GOES dynamic propagation of attitude

The spacecraft in the next series of Geostationary Operational Environmental Satellites (GOES-Next) are Earth pointing and have 5-year mission lifetimes. Because gyros can be depended on only for a few years of continuous use, they will be turned off during routine operations. This means attitude must, at times, be determined without benefit of gyros and, often, using only Earth sensor data. To minimize the interruption caused by dumping angular momentum, these spacecraft have been designed to reduce the environmental torque acting on them and incorporate an adjustable solar trim tab for fine adjustment. A new support requirement for GOES-Next is that of setting the solar trim tab. Optimizing its setting requires an estimate of the unbalanced torque on the spacecraft. These two requirements, determining attitude without gyros and estimating the external torque, are addressed by replacing or supplementing the gyro propagation with a dynamic one, that is, one that integrates the rigid body equations of motion. By processing quarter-orbit or longer batches, this approach takes advantage of roll-yaw coupling to observe attitude completely without Sun sensor data. Telemetered momentum wheel speeds are used as observations of the unbalanced external torques. GOES-Next provides a unique opportunity to study dynamic attitude propagation. The geosynchronous altitude and adjustable trim tab minimize the external torque and its uncertainty, making long-term dynamic propagation feasible. This paper presents the equations for dynamic propagation, an analysis of the environmental torques, and an estimate of the accuracies obtainable with the proposed method.

Markley, F. Landis↗
NASA NTRS1972

Spectral density measurements of gyro noise

Power spectral density (PSD) was used to analyze the outputs of several gyros in the frequency range from 0.01 to 200 Hz. Data were accumulated on eight inertial quality instruments. The results are described in terms of input angle noise (arcsec 2/Hz) and are presented on log-log plots of PSD. These data show that the standard deviation of measurement noise was 0.01 arcsec or less for some gyros in the passband from 1 Hz down 10 0.01 Hz and probably down to 0.001 Hz for at least one gyro. For the passband between 1 and 100 Hz, uncertainties in the 0.01 and 0.05 arcsec region were observed.

Truncale, A.↗
NASA NTRS1993

Real-time attitude determination and gyro calibration

We present results for two real-time filters prototyped for the Compton Gamma Ray Observatory (GRO), the Extreme Ultraviolet Explorer (EUVE), the Cosmic Background Explorer (COBE), and the next generation of Geostationary Operational Environmental Satellites (GOES). Both real and simulated data were used to solve for attitude and gyro biases. These filters promise advantages over single-frame and batch methods for missions like GOES, where startup and transfer-orbit operations require quick knowledge of attitude and gyro biases.

Challa, M.↗
NASA NTRS1977

Redundant integrated flight control/navigation inertial sensor complex

A redundant strapdown inertial navigation system for integrated flight control/navigation use is described. Design of the system, which consists of four tuned-gimbal gyros, eight accelerometers, and four processors, is discussed, with emphasis on its compact configuration (13 by 13 by 14 in.), based on symmetry properties of an octahedron. A matrix operator for least-squares combination of data from an arbitrary number of two-degree-of-freedom gyros is derived, and general parity equations for error analysis are given. Self-contained detection and isolation of a two-axis gyro failure is considered; system failure probability, which depends on component failure rates and self-correction capacities, is analyzed. Test data, including typical parity equation responses during motion and simulated gyro and accelerometer failures, are also presented.

Ebner, R. E.↗
NASA NTRS1983

Calibration of the aerodynamic coefficient identification package measurements from the shuttle entry flights using inertial measurement unit data

The Aerodynamic Coefficient Identification Package (ACIP) is an instrument consisting of body mounted linear accelerometers, rate gyros, and angular accelerometers for measuring the Space Shuttle vehicular dynamics. The high rate recorded data are utilized for postflight aerodynamic coefficient extraction studies. Although consistent with pre-mission accuracies specified by the manufacturer, the ACIP data were found to contain detectable levels of systematic error, primarily bias, as well as scale factor, static misalignment, and temperature dependent errors. This paper summarizes the technique whereby the systematic ACIP error sources were detected, identified, and calibrated with the use of recorded dynamic data from the low rate, highly accurate Inertial Measurement Units.

Heck, M. L.↗
NASA NTRS1994

MME-based attitude dynamics identification and estimation for SAMPEX

A method is described for obtaining optimal attitude estimation algorithms for spacecraft lacking attitude rate measurement devices (rate gyros), and then demonstrated using actual flight data from the Solar, Anomalous, and Magnetospheric Particle Explorer (SAMPEX) spacecraft. SAMPEX does not have on-board rate sensing, and relies on sun sensors and a three-axis magnetometer for attitude determination. Problems arise since typical attitude estimation is accomplished by filtering measurements of both attitude and attitude rates. Rates are nearly always sampled much more densely than are attitudes. Thus, the absence/loss of rate data normally reduces both the total amount of data available and the sampling density (in time) by a substantial fraction. As a result, the sensitivity of the estimates to model uncertainty and to measurement noise increases. In order to maintain accuracy in the attitude estimates, there is increased need for accurate models of the rotational dynamics. The proposed approach is based on the minimum model error (MME) optimal estimation strategy, which has been successfully applied to estimation of poorly modeled dynamic systems which are relatively sparsely and/or noisily measured. The MME estimates may be used to construct accurate models of the system dynamics (i.e. perform system model identification). Thus, an MME-based approach directly addresses the problems created by absence of attitude rate measurements.

Depena, Juan↗
NASA NTRS1995

Use of nonlinear identification in robust attitude and attitude rate estimation for SAMPEX

A method is described for obtaining optimal attitude estimation/identification algorithms for spacecraft lacking attitude rate measurement devices (rate gyros), and then demonstrated using actual flight data from the Solar, Anomalous, and Magnetospheric Particle Explorer (SAMPEX) spacecraft. SAMPEX does not have on-board rate sensing, and relies on sun sensors and a three-axis magnetometer for attitude determination. The absence of rate data normally reduces both the total amount of data available and the sampling density (in time) by a substantial fraction. In addition, attitude data is occasionally unavailable (for example, during sun occultation). As a result, the sensitivity of the estimates to model uncertainty and to measurement noise increases. In order to maintain accuracy in the attitude estimates, there is an increased need for accurate models of the rotational dynamics. The Minimum Model Error(MME)/Least Square Correlation(LSC) algorithm accurately identifies an improved model for SAMPEX to be used during periods of complete data loss or extreme noise. The model correction is determined by estimating only one orbit(the identification pass) just prior to the assumed data loss(the prediction pass). The MME estimator correctly predicted the states during the identification phase, but more importantly determines the necessary model correction trajectory, d(t). The LSC algorithm is then used to find this trajectory's functional form, H(x(t)). The results show significant improvement of the new corrected model's attitude estimates as compared to the original uncorrected model's estimates. The possible functional form of the correction term is limited at this point in the study to functions strictly of the estimated states. The results, however, strongly suggest that functions based on the relative position of the satellite may also be possible candidates for future consideration.

Mook, D. Joseph↗
NASA NTRS1972

Determination of angles of attack and sideslip from radar data and a roll-stabilized platform

Equations for angles of attack and sideslip relative to both a rolling and nonrolling body axis system are derived for a flight vehicle for which radar and gyroscopic attitude data are available. The method is limited to application where a flat, nonrotating earth may be assumed. The gyro measures attitude relative to an inertial reference in an Euler angle sequence. In particular, a pitch, yaw, and roll sequence is used as an example in the derivation. Sample calculations based on flight data are presented to illustrate the method. Results obtained with the present gyro method are compared with another technique that uses onboard camera data.

Preisser, J. S.↗
NASA NTRS1974

Comparison of flight data and analysis for hingeless rotor regressive inplane mode stability

Analytical and experimental data obtained during the development of the AH-56A covering stability of the regressive inplane mode, including coupling with other modes such as body and rotor plunge are reported. Data were obtained on two distinctly different control systems; both gyro controlled, but one with feathering moment feedback and the other with direct flapping feedback. A review was made of analytical procedures employed in investigating the stability of this mode and a comparison was made of the analytical and experimental data. The effect of certain parameters including blade droop, sweep, delta 3, alpha 1, vehicle roll inertia, inplane frequency, and rpm and forward speed on the mode were also reviewed. It was shown that the stability of this mode is treatable by analysis and that adequate stability is achievable without recourse to auxiliary inplane damping devices.

Anderson, W. D.↗
NASA NTRS1977

F-8C adaptive flight control laws

Three candidate digital adaptive control laws were designed for NASA's F-8C digital flyby wire aircraft. Each design used the same control laws but adjusted the gains with a different adaptative algorithm. The three adaptive concepts were: high-gain limit cycle, Liapunov-stable model tracking, and maximum likelihood estimation. Sensors were restricted to conventional inertial instruments (rate gyros and accelerometers) without use of air-data measurements. Performance, growth potential, and computer requirements were used as criteria for selecting the most promising of these candidates for further refinement. The maximum likelihood concept was selected primarily because it offers the greatest potential for identifying several aircraft parameters and hence for improved control performance in future aircraft application. In terms of identification and gain adjustment accuracy, the MLE design is slightly superior to the other two, but this has no significant effects on the control performance achievable with the F-8C aircraft. The maximum likelihood design is recommended for flight test, and several refinements to that design are proposed.

Hartmann, G. L.↗