Search NASA⌕ Search

SEARCH · Search NASA

Results for “hard technologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Development of a COTS Mass Storage Unit for the Space Readiness Coherent Lidar Experiment

The technology to develop a Mass Storage Unit (MSU) using commercial-off-the-shelf (COTS) hard drives is an on-going challenge to meet the Space Readiness Coherent Lidar Experiment (SPARCLE) program requirements. A conceptual view of SPARCLE's laser collecting atmospheric data from the shuttle is shown in Figure 1. The determination to develop this technology required several in depth studies before an actual COTS hard drive was selected to continue this effort. Continuing the development of the MSU can, and will, serve future NASA programs that require larger data storage and more on-board processing.

Liggin, Karl↗

X-ray detector physics and applications; Proceedings of the Meeting, San Diego, CA, July 23, 24, 1992

Recent developments in X-ray and hard X-ray imaging detector, high-intensity sources, hard X-ray imaging optics, calibration, and detection technologies are discussed. Particular attention is given to a high-MTF X-ray image intensifier, application of monolithic CdZnTe linear solid state ionization detectors for X-ray imaging, magnetic response of high-Tc superconductors to X-ray radiation and detection of X-rays, laboratory soft X-ray source with foil target, detection of explosive materials using nuclear radiation, energy response of astronomical CCD X-ray detectors, calibration techniques for high-flux X-ray detectors, fabrication of grazing-incidence optics using flow-polishing techniques, and numerical simulations for capillary-based X-ray optics. (No individual items are abstracted in this volume)

Hoover, Richard B.↗

Timing analysis by model checking

The safety of modern avionics relies on high integrity software that can be verified to meet hard real-time requirements. The limits of verification technology therefore determine acceptable engineering practice. To simplify verification problems, safety-critical systems are commonly implemented under the severe constraints of a cyclic executive, which make design an expensive trial-and-error process highly intolerant of change. Important advances in analysis techniques, such as rate monotonic analysis (RMA), have provided a theoretical and practical basis for easing these onerous restrictions. But RMA and its kindred have two limitations: they apply only to verifying the requirement of schedulability (that tasks meet their deadlines) and they cannot be applied to many common programming paradigms. We address both these limitations by applying model checking, a technique with successful industrial applications in hardware design. Model checking algorithms analyze finite state machines, either by explicit state enumeration or by symbolic manipulation. Since quantitative timing properties involve a potentially unbounded state variable (a clock), our first problem is to construct a finite approximation that is conservative for the properties being analyzed-if the approximation satisfies the properties of interest, so does the infinite model. To reduce the potential for state space explosion we must further optimize this finite model. Experiments with some simple optimizations have yielded a hundred-fold efficiency improvement over published techniques.

Naydich, Dimitri↗

AM03-AM121-115 Hard X-Ray Optics Development at MSFC

We have developed the electroformed-nickel replication process to enable us to fabricate light-weight hard-x-ray region. Two projects currently utilizing this technology are the production of over 250 r from 5 to 10 cm, for our HERO balloon payload, and 15- and 23-cm-diameter shells for a prototype module. The challenge for the former is to fabricate, mount, align and fly a large number of high-r constraints of a modest budget. For the latter, the challenge is to maintain high angular resolution shell thicknesses (100 micron) which make the shells extremely sensitive to electroforming stresses process does not degrade the ultra-smooth surface finish (approx. 3 A required for eventual multilayer c on these two programs.

Ramsey, Brian↗

Enabling technology for NASA's Europa Orbiter mission

The authors will describe the drivers for the subsystem requirements in the Europa Orbiter mission, in particular the mission criticality of the IMU and the predicted natural space radiation environments that require enabling technologies to be identified. Descriptions of the Europa IMU and the HRG technology are given with emphasis on the inherent radiation hardness in the HRG principle of operation and sensor construction, as well as the steps taken to further harden the sensor electronics.

inertial measurement unit inertial reference unit ↗

BioNutrients-2: Improvements to the BioNutrients-1 Nutrient Production System

The BioNutrients (BN) project aims to develop an on-demand biological production system capable of rapid and safe delivery of multiple nutrients in single-use production packs for long-duration missions. The general concept of this system is to develop edible engineered microorganisms that produce nutrients for human consumption following long-term storage, revival, and growth. BN-1 is a five-year flight project currently on the International Space Station (ISS). It is testing the long-term storage of various microorganisms for the biomanufacturing of space-relevant compounds and validating the performance of the first generation of production packs. The BN-2 project expands the BN-1 flight project scope by introducing novel products, broadening the range of microbial food sources, and improving upon production pack hardware. We are optimizing the biomanufacturing platform for in situ production of yogurt and kefir on the ISS. BN-2 also will test engineered microorganisms, including a probiotic strain, to produce carotenoids or follistatin. To improve the feasibility of this technology for mission use, we transitioned from a hard-shell pack to a second-generation fluorinated ethylene propylene (FEP) bag. The single-use FEP bioreactor facilitates growth of target organisms in a contaminant free environment, while reducing mass and volume compared to the BN-1 hardware. These bioreactors will be employed for production of additional space-relevant products in the BN-2 project. On-orbit testing of FEP production packs will enable optimization of the platform for eventual flight use by the crew.

Natalie Ball↗

Comparative Study of Additively Manufactured Inconel 625 In the As-Built and Heat-Treated Condition

This study was conducted to characterize the microstructure and mechanical properties of Inconel 625 manufactured with laser powder bed fusion (L-PBF), electron beam melting (EBM), wire arc additive manufacturing (WAAM), electron beam directed energy deposition (EB-DED), laser powder directed energy deposition (LP-DED), and laser wire directed energy deposition (LW-DED) in both the as built and heat-treated condition. The heat treatment in this study included stress relieving, hot isostatic pressure (HIP), and solution treatment. The effects of the heat treatment on the grain widths and hardness of the alloy will be observed across the technologies before and after heat-treatment. At the end of this study there will be a comparative analysis of the alloy Inconel 625 across the six technologies.

V Luna↗

Rad-Hard Structured ASIC Body of Knowledge

Structured Application-Specific Integrated Circuit (ASIC) technology is a platform between traditional ASICs and Field-Programmable Gate Arrays (FPGA). The motivation behind structured ASICs is to combine the low nonrecurring engineering costs (NRE) costs of FPGAs with the high performance of ASICs. This report provides an overview of the structured ASIC platforms that are radiation-hardened and intended for space application

Heidecker, Jason↗

Compact Holographic Data Storage

NASA's future missions would require massive high-speed onboard data storage capability to Space Science missions. For Space Science, such as the Europa Lander mission, the onboard data storage requirements would be focused on maximizing the spacecraft's ability to survive fault conditions (i.e., no loss in stored science data when spacecraft enters the 'safe mode') and autonomously recover from them during NASA's long-life and deep space missions. This would require the development of non-volatile memory. In order to survive in the stringent environment during space exploration missions, onboard memory requirements would also include: (1) survive a high radiation environment (1 Mrad), (2) operate effectively and efficiently for a very long time (10 years), and (3) sustain at least a billion write cycles. Therefore, memory technologies requirements of NASA's Earth Science and Space Science missions are large capacity, non-volatility, high-transfer rate, high radiation resistance, high storage density, and high power efficiency. JPL, under current sponsorship from NASA Space Science and Earth Science Programs, is developing a high-density, nonvolatile and rad-hard Compact Holographic Data Storage (CHDS) system to enable large-capacity, high-speed, low power consumption, and read/write of data in a space environment. The entire read/write operation will be controlled with electrooptic mechanism without any moving parts. This CHDS will consist of laser diodes, photorefractive crystal, spatial light modulator, photodetector array, and I/O electronic interface. In operation, pages of information would be recorded and retrieved with random access and high-speed. The nonvolatile, rad-hard characteristics of the holographic memory will provide a revolutionary memory technology meeting the high radiation challenge facing the Europa Lander mission. Additional information is contained in the original extended abstract.

Chao, T. H.↗

Calibration of High Frequency MEMS Microphones

Understanding and controlling aircraft noise is one of the major research topics of the NASA Fundamental Aeronautics Program. One of the measurement technologies used to acquire noise data is the microphone directional array (DA). Traditional direction array hardware, consisting of commercially available condenser microphones and preamplifiers can be too expensive and their installation in hard-walled wind tunnel test sections too complicated. An emerging micro-machining technology coupled with the latest cutting edge technologies for smaller and faster systems have opened the way for development of MEMS microphones. The MEMS microphone devices are available in the market but suffer from certain important shortcomings. Based on early experiments with array prototypes, it has been found that both the bandwidth and the sound pressure level dynamic range of the microphones should be increased significantly to improve the performance and flexibility of the overall array. Thus, in collaboration with an outside MEMS design vendor, NASA Langley modified commercially available MEMS microphone as shown in Figure 1 to meet the new requirements. Coupled with the design of the enhanced MEMS microphones was the development of a new calibration method for simultaneously obtaining the sensitivity and phase response of the devices over their entire broadband frequency range. Over the years, several methods have been used for microphone calibration. Some of the common methods of microphone calibration are Coupler (Reciprocity, Substitution, and Simultaneous), Pistonphone, Electrostatic actuator, and Free-field calibration (Reciprocity, Substitution, and Simultaneous). Traditionally, electrostatic actuators (EA) have been used to characterize air-condenser microphones for wideband frequency ranges; however, MEMS microphones are not adaptable to the EA method due to their construction and very small diaphragm size. Hence a substitution-based, free-field method was developed to calibrate these microphones at frequencies up to 80 kHz. The technique relied on the use of a random, ultrasonic broadband centrifugal sound source located in a small anechoic chamber. Phase calibrations of the MEMS microphones were derived from cross spectral phase comparisons between the reference and test substitution microphones and an adjacent and invariant grazing-incidence 1/8-inch standard microphone.

Shams, Qamar A.↗

Lightweight Multifunctional Planetary Probe for Extreme Environment Exploration and Locomotion

The demand to explore new worlds requires the development of advanced technologies that enable landed science on uncertain terrains or in hard to reach locations. As a result, contemporary Entry, Descent, Landing, (EDL) and additional locomotion (EDLL) profiles are becoming increasingly more complex, with the introduction of lifting/guided entries, hazard avoidance on descent, and a plethora of landing techniques including airbags and the skycrane maneuver. The inclusion of each of these subsystems into a mission profile is associated with a substantial mass penalty. This report explores the new all-in-one entry vehicle concept, TANDEM, a new combined EDLL concept, and compares it to the current state of the art EDL systems. The explored system is lightweight and collapsible and provides the capacity for lifting/guided entry, guided descent, hazard avoidance, omnidirectional impact protection and surface locomotion without the aid of any additional subsystems. This Phase I study explored: 1. The capabilities and feasibility of the TANDEM concept as an EDLL vehicle. 2. Extensive impact analysis to ensure mission success in unfavorable landing conditions, and safe landing in Tessera regions. 3. Development of a detailed design for a conceptual mission to Venus. As a result of our work it was shown that: 1. TANDEM provides additional benefits over the Adaptive, Deployable Entry Placement Technology (ADEPT) including guided descent and surface locomotion, while reducing the mass by 38% compared to the ADEPT-VITaL mission. 2. Demonstrated that the design of tensegrity structures, and TANDEM specifically, grows linearly with an increase in velocity, which was previously unknown. 3. Investigation of surface impact revealed a promising results that suggest a properly configured TANDEM vehicle can safely land and preform science in the Tessera regions, which was previously labeled by the Decadal Survey as, largely inaccessible despite its high scientific interest. This work has already resulted in a NASA TM and will be submitted to the Journal of Spacecraft and Rockets.

landing techniques↗

Grazing Incidence Nickel Replicated Optics for Hard X-ray Telescopes

The requirements for future hard x-ray (up to 50 keV) telescopes are lightweight, high angular resolution optics with large collecting areas. Grazing incidence replicated optics are an excellent candidate for this, type of mission, providing better angular resolution, comparable area/unit mass, and simpler fabrication than multilayer-coated foils. Most importantly, the technology to fabricate the required optics currently exists. A comparison of several hard x-ray telescope designs will be presented.

Peturzzo, J. J., III↗

NASA Science Technology Development Programs for Ocean Worlds Exploration

The exploration of ocean worlds such as Europa and Enceladus supports NASA’s goal to search for life and potentially habitable regions elsewhere in the universe, and further promises to help us understand the origins, evolution, and limits of life on Earth. Over the past several years, NASA’s Planetary Science Division has funded several technology development programs to enable future surface and subsurface missions to ocean worlds. These programs include Instrument Concepts for Europa Exploration (ICEE), Concepts for Ocean Worlds Life Detection Technology (COLDTech), Scientific Exploration Subsurface Access Mechanism for Europa (SESAME), Applied Information Systems Research: Autonomous Robotics Research for Ocean Worlds (AISR:ARROW), and Astrodynamics in Support of Icy Worlds Missions. Tasks selected under these programs include the development of scientific instruments including seismometers, imagers, spectrometers, and organic analyzers, and platform technologies including drills, melt probes, through-ice communications, radiation-hard electronics, and autonomy for surface operations. This paper describes the objectives of each of these programs and provides a summary of the work that has been completed or is underway in each.

technology↗

NASA Science Technology Development Programs for Ocean Worlds Exploration

The exploration of icy satellites such as Europa and Enceladus supports NASA’s goal to search for life and potentially habitable regions elsewhere in the universe, and further promises to help us understand the origins, evolution, and limits of life on Earth. Over the past several years, NASA’s Planetary Science Division has funded several technology development programs to enable future surface and subsurface missions to ocean worlds. These programs include Instrument Concepts for Europa Exploration (ICEE), Concepts for Ocean Worlds Life Detection Technology (COLDTech), Scientific Exploration Subsurface Access Mechanism for Europa (SESAME), Applied Information Systems Research: Autonomous Robotics Research for Ocean Worlds (AISR:ARROW), and Astrodynamics in Support of Icy Worlds Missions. Tasks selected under these programs include the development of scientific instruments including seismometers, imagers, spectrometers, and organic analyzers, and also platform technologies including drills, melt probes, through-ice communications, radiation-hard electronics, and autonomy for surface operations. This paper describes the objectives of each of these programs and provides a summary of the work that has been completed or is underway in each.

science instruments↗

Plasma deposition and surface modification techniques for wear resistance

The ion-assisted or plasma coating technology is discussed as it applies to the deposition of hard, wear resistant refractory compound films. Of the many sputtering and ion plating modes and configurations the reactive magnetron sputtering and the reactive triode ion plating techniques are the preferred ones to deposit wear resistant coatings for tribological applications. Both of these techniques incorporate additional means to enhance the ionization efficiency and chemical reaction to precision tailor desirable tribological characteristics. Interrelationships between film formation, structure, and ribological properties are strictly controlled by the deposition parameters and the substrate condition. The enhanced ionization contributes to the excellent adherence and coherence, reduced internal stresses and improved structural growth to form dense, cohesive, equiaxed grain structure for improved wear resistance and control.

Spalvins, T.↗

Protective Coating

Inorganic Coatings, Inc.'s K-Zinc 531 protective coating is water-based non-toxic, non-flammable and has no organic emissions. High ratio silicate formula bonds to steel, and in 30 minutes, creates a very hard ceramic finish with superior adhesion and abrasion resistance. Improved technology allows application over a minimal commercial sandblast, fast drying in high humidity conditions and compatibility with both solvent and water-based topcoats. Coating is easy to apply and provides long term protection with a single application. Zinc rich coating with water-based potassium silicate binder offers cost advantages in materials, labor hours per application, and fewer applications over a given time span.

Source record↗

BioNutrients-2: Improvements to the BioNutrients-1 Nutrient Production System

The BioNutrients (BN) project aims to develop an on-demand nutrient production system capable of rapid and safe delivery of multiple nutrients in a single-use production pack for long-duration missions. The general concept of this system will be to develop an edible engineered microorganism capable of surviving during long-term storage, revival and growth of that microorganism for product production, and delivery of precise quantities of nutrients for human consumption. BN-1 is a five-year flight project currently on the International Space Station (ISS). It is testing the long-term storage of various microorganisms for the biomanufacturing of space relevant compounds and to validate the performance of the first generation (Gen-1) of production packs. The BN-2 project is a continuation of the BN-1 flight project and intends to expand the projects overall scope by introducing novel products, broadening the range of microbial food sources, and improving previously designed hardware from the BN-1 project. We are in the process of optimizing our platform biomanufacturing technology for in situ production of yogurt and kefir on the ISS. BN-2 will test the efficacy of this technology for future delivery of probiotic organisms which can be engineered to produce additional nutritional supplements (consumption by the crew is not planned in this project). Furthermore, to improve the feasibility of this technology for mission use we have transitioned from a hard-shell pack to a Gen-2, fluorinated ethylene propylene (FEP) bag. The single-use FEP bioreactor will facilitate growth of known organisms and ensure a contaminant free environment, while reducing mass and volume. These bioreactors will be employed for production of additional space relevant products in the BN-2 project. On-orbit testing of Gen-2 production packs will be necessary for future iterations, in order to optimize bag design and product production for eventual flight use by the crew.

BioNutrients↗

Planetary Suit Hip Bearing Model for Predicting Design vs. Performance

Designing a planetary suit is very complex and often requires difficult trade-offs between performance, cost, mass, and system complexity. In order to verifying that new suit designs meet requirements, full prototypes must eventually be built and tested with human subjects. Using computer models early in the design phase of new hardware development can be advantageous, allowing virtual prototyping to take place. Having easily modifiable models of the suit hard sections may reduce the time it takes to make changes to the hardware designs and then to understand their impact on suit and human performance. A virtual design environment gives designers the ability to think outside the box and exhaust design possibilities before building and testing physical prototypes with human subjects. Reductions in prototyping and testing may eventually reduce development costs. This study is an attempt to develop computer models of the hard components of the suit with known physical characteristics, supplemented with human subject performance data. Objectives: The primary objective was to develop an articulating solid model of the Mark III hip bearings to be used for evaluating suit design performance of the hip joint. Methods: Solid models of a planetary prototype (Mark III) suit s hip bearings and brief section were reverse-engineered from the prototype. The performance of the models was then compared by evaluating the mobility performance differences between the nominal hardware configuration and hardware modifications. This was accomplished by gathering data from specific suited tasks. Subjects performed maximum flexion and abduction tasks while in a nominal suit bearing configuration and in three off-nominal configurations. Performance data for the hip were recorded using state-of-the-art motion capture technology. Results: The results demonstrate that solid models of planetary suit hard segments for use as a performance design tool is feasible. From a general trend perspective, the suited performance trends were comparable between the model and the suited subjects. With the three off-nominal bearing configurations compared to the nominal bearing configurations, human subjects showed decreases in hip flexion of 64%, 6%, and 13% and in hip abduction of 59%, 2%, and 20%. Likewise the solid model showed decreases in hip flexion of 58%, 1%, and 25% and in hip abduction of 56%, 0%, and 30%, under the same condition changes from the nominal configuration. Differences seen between the model predictions and the human subject performance data could be attributed to the model lacking dynamic elements and performing kinematic analysis only, the level of fit of the subjects with the suit, the levels of the subject s suit experience.

Cowley, Matthew S.↗