Search NASA⌕ Search

SEARCH · Search NASA

Results for “ignition component”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Improving Unit Flexibility Utilizing Plasma Ignitors

Coal fired steam generation operators face increasing market challenges, including competition from low cost generation, renewables, and regulatory pressure. These market conditions are forcing utilities to operate their coal assets in a more flexible mode, including more frequent starts and stops, faster ramp rates, frequent cycling, and extended operation at the lowest possible loads. Without upgrades to firing and control systems, pressure parts, and auxiliary systems, CAPEX and OPEX costs will increase significantly. Typically, expensive support fuels (Oil or Gas) are required to maintain safe, stable coal ignition when operating below 25% to 35% MCR (Maximum Continuous Rating). The exact minimum load without support fuel differs depending upon unit design specifications and fuel being burned. Frequent starts also increase the use of support fuels. The firing and burner control systems must be designed to allow for proper operation over the unit’s load range, ensuring that all mechanical components operate properly, and proper control of air and fuel streams can be maintained. To address the need for frequent starts and the need for stable low load operation on coal fired steam generators, this paper discusses options available, including, Firing Systems upgrades, Digital solutions, and pressure part upgrades. Several case studies are included that highlight options available allowing units to stay in operation and reduce CAPEX and OPEX costs.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Status and prospects for inertial fusion energy via lasers

Fusion energy is the ultimate clean and limitless energy source, but its development requires overcoming many scientific and technological challenges. For the first time in the 60-year long history of fusion research, ignition and target gain above unity (G>1) were demonstrated in the laboratory at the National Ignition Facility at the Lawrence Livermore National Laboratory in 2022. Turning laser fusion into an energy source requires that the results from single shot experiments be replicated at much higher repetition rates of many shots per second to produce high average power at relatively low cost. Furthermore, this requires the development of new laser technologies, mass production of suitable targets, accurate injection and tracking systems and new materials for the reactor chamber components and final optics. Ultra broadband and deep UV light are laser advances that can dramatically improve the laser energy coupling to the target thereby reducing the laser energy and power requirements.

Fusion energy↗
DOE OSTI2023

Model predictive control of mixing controlled compression ignition operation for low reactivity fuels

Using gasoline or other low reactivity fuels with a pilot injection or port fuel injection in a compression ignition engine has shown great potential in reducing NOx emissions while keeping high thermal efficiency compared to diesel. However, excessive combustion noise is caused by a high maximum pressure rise rate in the cylinder due to the higher fractions of premixed charge of the low-reactivity fuel. This noise can result in structural damage to engine components and as such, combustion noise limits the range of the operating parameters and makes the control of such engines challenging. In this study, a simulation environment was built up in MATLAB/Simulink leveraging a physics-based zero-dimension combustion model to capture the in-cylinder pressure time traces as well as metrics relevant to thermal efficiency and combustion noise. Here, in order to also facilitate the control of emissions, machine learning models were investigated to capture NOx emissions. A kernel-based extreme learning machine (K-ELM) performed best and had a coefficient of correlation (R-squared) of 0.998. The combustion and NOx emission models are valid for not only conventional gasoline fuel but also oxygenated alternative fuel blends at three different pilot injection strategies. In order to track key combustion metrics while keeping noise and emissions within constraints, a model predictive control (MPC) was applied for a compression ignition engine operating with a range of potential fuels and fuel injection strategies. The MPC is validated under different scenarios, including a load step change, fuel type change, and injection strategy change, with proportional–integral (PI) control as the baseline. The simulation results show that MPC reduces about 26% of ringing intensity in the transient process and 17% at the steady state for E30. Generally, MPC can optimize the overall performance through modifying the main injection timing, pilot fuel mass, and exhaust gas recirculation (EGR) fraction.

42 ENGINEERING↗
DOE OSTI2024

A compact and portable gamma-ray spectrometer (GRASP) for inertial confinement fusion and basic science experiments

A compact and portable gamma-ray spectrometer has been designed to diagnose different components of the inertial confinement fusion-relevant γ-ray spectrum with energies between ∼3.7–17.9 MeV. The system is designed to be as compact as possible for convenient transportation and fielding in diagnostic ports on the OMEGA laser, the National Ignition Facility, and other photon-source facilities. The system consists of a conversion foil for Compton scattering in front of four magnetic spectrometer “arms,” each covering a different energy range and constructed out of cylindrical permanent magnet Halbach arrays. Monte Carlo simulations have been used to optimize and assess the performance of the conversion foil, and COSY INFINITY ion-optical simulations have been used to optimize the spectrometer magnets. The performance of the design is assessed for a simulated direct-drive γ-ray spectrum. Spanning its total γ-ray energy bandwidth and using a 1.7 mm thick boron conversion foil, the system’s total energy resolution and efficiency are ∼15.8%–4.5% and 5.4 × 10−7–3.7 × 10−7e−/γ, respectively, with room for improvement. Spectral γ-ray measurements will provide guidance to the inertial confinement fusion program toward achieving high-energy gain relevant to inertial fusion energy and enable new measurement capabilities for basic discovery science.

Instruments & Instrumentation↗
DOE OSTI2022

Numerical analysis of soot emissions from gasoline-ethanol and gasoline-butanol blends under gasoline compression ignition conditions

In the present work, computational fluid dynamics (CFD) simulations of a single-cylinder gasoline compression ignition (GCI) engine were performed to investigate the impact of blending two biofuels, ethanol and n-butanol, with gasoline on the trade-off between combustion phasing and soot emissions under low load conditions. Here, in order to represent market gasoline (RD5-87), a four-component toluene primary reference fuel (TPRF) + ethanol (ETPRF) surrogate (with 20% ethanol by mole; E20) was formulated using a neural network based octane predictor such that the surrogate had the same ethanol content, Research Octane Number (RON) and Octane Sensitivity (S). In addition, a novel skeletal kinetic mechanism for ETPRF and TPRF + n-butanol (BTPRF) blends, incorporating polycyclic aromatic hydrocarbon (PAH) chemistry, was developed. A three-dimensional (3D) engine CFD formulation employing the skeletal mechanism, adaptive mesh refinement (AMR), finite-rate chemistry approach, and hybrid method of moments (HMOM) was adopted to capture the in-cylinder combustion phenomena and soot emissions. The engine CFD model was validated against RD5-87 experimental data for a broad range of start-of-injection (SOI) timings (-21/-27/-36/-45 crank angle degrees (CAD) after top-dead center (aTDC)), with respect to in-cylinder pressure, heat release rate, combustion phasing, and soot emissions. The closed-cycle simulation results were analyzed to elucidate the non-monotonic trend of soot emissions versus SOI timing: SOI-36 > SOI-45 > SOI-21 > SOI-27. Thereafter, the validated CFD model was employed to simulate the combustion of a gasoline-ethanol blend with 45% (by mole) ethanol (E45) and a gasoline-butanol blend with 45% (by mole) n-butanol (B45) under the same operating conditions to study the effects of fuel composition and SOI timing on combustion phasing and soot emissions. The sooting propensity followed the trend: B45 > E20 > E45 at all SOI timings. Overall, it was observed that the autoignition propensity was primarily related to fuel chemistry. On the other hand, sooting propensity showed strong coupling with both fuel chemistry and physical properties, with greater impact of fuel physical properties at advanced SOI timings.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Security constrained optimal power shutoff for wildfire risk mitigation

Abstract Electric grid faults are increasingly the source of ignition for major wildfires. To reduce the likelihood of such ignitions in high risk situations, utilities use preemptive de‐energization of power lines, commonly referred to as Public Safety Power Shutoffs (PSPS). Besides raising challenging trade‐offs between power outages and wildfire safety, PSPS removes redundancy from the network at a time when component faults are likely to happen. This may leave the network particularly vulnerable to unexpected line faults that may occur while the PSPS is in place. Previous works have not explicitly considered the impacts of these outages. To address this gap, the Security Constrained Optimal Power Shutoff problem is proposed which uses post‐contingency security constraints to model the impact of unexpected line faults when planning a PSPS. This model enables, for the first time, the exploration of a wide range of trade‐offs between both wildfire risk and pre‐ and post‐contingency load shedding when designing PSPS plans, providing useful insights for utilities and policy makers considering different approaches to PSPS. The efficacy of the model is demonstrated using the EPRI 39‐bus system as a case study. The results highlight the potential risks of not considering security constraints when planning PSPS and show that incorporating security constraints into the PSPS design process improves the resilience of current PSPS plans.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

Analysis of Dynamic Behavior of the Target and the Deuterium-Tritium Ice in Magnetic-Field Assisted Implosions

The use of strong magnetic fields to augment the output energy of inertial confinement fusion experiments at the National Ignition Facility is of high interest. It offers the potential of reducing electron thermal conduction and increasing hot-spot alpha heating with little to no change in hohlraum behavior. In these magnetically assisted ignition experiments, the ultimate goal is to add a B-field in the form of a pulse ranging from 25 to 60 T to a high-performing hohlraum implosion several microseconds before impingement of the laser beams. This requires eliminating metallic components in the target and replacing them with electrically nonconducting materials. However, the strong eddy currents generated by the rapidly increasing high B-field, which were calculated to be as high as 2000 K, can heat the hohlraum. Here in this paper, we examine the transient effects of this rapid temperature change on the behavior of the target as well as the fuel layer composed typically of deuterium and tritium. Using simulations and calculations for limiting case scenarios, we find that the effect of the heating is not restrictive toward the performance of the target or the quality of the deuterium-tritium ice.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Validation of Octane Hyperboosting Phenomenon in Prenol and Structurally Related Olefinic Alcohols

Hyperboosting is a recently discovered phenomenon in which the research octane number (RON) of a blend is higher than both the neat blendstock and the neat fuel it was blended into. RON is a measure of a fuel's resistance to knock, and knock is a cause of engine inefficiency. Blends which exhibit hyperboosting are blends in which an overall improvement in engine efficiency may be expected. The first discovery of hyperboosting came from blending experiments in which prenol was blended into several different base fuels. Here, ignition delay time (IDT) measurements taken using a commercially available constant volume combustion chamber called the Advanced Fuel Ignition Delay Analyzer (AFIDA) are presented. The data show that some prenol blends have longer IDTs (lower reactivity) than either neat prenol or the base fuel, providing further evidence of hyperboosting. Additionally, more blending data is presented in which the base fuel is varied, which allows for a better understanding of hyperboosting sensitivity to chemical classes. The data indicate that aromatics may inhibit, and branched alkanes may enhance the magnitude of hyperboosting observed. Enthalpy of vaporization estimates are also given for several molecules which are blended into a 4-component surrogate. These estimates are derived from Equation of State simulations and reveal that there is no observable correlation between hyperboosting and enthalpy of vaporization. Blending data for molecules which share structural similarities with prenol are also presented. Structure property relationships are suggested, in which the double bond motif of prenol seems to play an important role in hyperboosting. This may help to understand hyperboosting and its underlying mechanism. Lastly, blending curves of surrogate blends with prenol experienced hyperboosting under lean (Homogeneous Charged Compression Ignition-HCCI) operating conditions, which validates that hyperboosting is not an artifact of the octane test methods, but inherent to the properties of prenol.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Design and Experimental Demonstration of an Additive Manufactured Smart Oxy-Methane Burner for High Pressure and Supercritical Combustion

Pressurized oxy combustion-based systems can improve efficiency by recovering latent heat of the steam in the Flue Gas and achieving 90% CO2 capture. In addition, the novel Directly Heated Supercritical Carbon Dioxide (DH-SCO2) power cycles can achieve high thermal efficiencies and provide nearly full carbon capture. Additionally, due to the reduction of flue gas at higher pressure, smaller system size and capital cost reductions are also possible. Recent thermodynamic analysis of the DH-SCO2 cycle performed by the UTEP research team shows that combustion conditions in the vicinity of 300 bar pressure and 1000-1400 K temperature allow for relatively high system efficiencies while operating within the limit of available combustor materials. However, the realization of a directly heated supercritical power cycle requires combustion systems to operate in supercritical conditions and at temperature far below the blowout limit of conventional flames (above 1500 K). The thermodynamic properties along with the combustion properties and kinetics are unexplored at such conditions. Additionally, the interaction of the supercritical environment with energy components is also unknown. High-pressure combustion tests are performed using a smart burner at some intermediate pressure ranges (<20 bar) to help minimize these knowledge gaps. The knowledge obtained from the high-pressure test will assist in understanding the combustion chamber pressurization mechanism, ignition and flame behavior at the elevated pressure. The obtained data will act as a systematic first step in testing at higher pressures of 100 and 300 bar pressures.The primary purpose of this Dissertation is to demonstrate the operability of a low NOx smart burner for oxy-methane combustion at high pressure (< 20 bar) and scalable up to supercritical conditions. A shear co-axial smart burner is designed with a real-time temperature monitoring capability to understand the burner face interaction at high-pressure conditions. In addition, the burner has four independent injection ports to allow the independent injection of fuel and dilution gases in the combustor. The maximum operating capability of the burner is 575 kWth. The burner was fabricated using a Laser Powder Bed Fusion process with Nickel Alloy 718. A powder removal technology was invented comprising ultrasonic vibration, liquid nitrogen exposure and media blasting to remove powders from internal channels of the burner. The burner operability tests are performed in the high-pressure combustor and the swirl combustor. The high-pressure combustor was used to investigate the burner operability and thermal soak back at different pressurized conditions. The experimental tests in high-pressure combustor up to 275 kWth input resulted in 16.5 bar chamber pressure and 198°C thermal soaks back to the burner. The burner was capable of providing the required thermal input within a 3% deviation range. In addition, soot formation occurred at high-pressure tests. The swirl combustor was used to observe the flame stability of the burner. Flame lift-off was observed for jet velocities above 450 m/s. Additionally, lift-off decreased for low co-flow velocities. CO2 dilution experiments showed increased flame instabilities for all conditions above 50% dilution ratios. At lower thermal inputs, partial flame blow-offs occurred for dilution ratios above 50%. All conditions significantly reduced the flame temperature and increased the flame lift-off height. Finally, a 2nd generation AM smart burner was designed using the knowledge from the 1st generation burner experiments. The 2nd generation burner incorporated two sets of swirlers with 0.9 swirl no. A cooling system was also designed for long-duration tests at higher pressures. The thermal input and division of the burner's power are kept the same as the 1st generation burner. The burner is to be fabricated using nickel-alloy 718 for high-pressure handling capability. The design can sustain at high-pressure conditions up to 100 bar.

Islam, Md Nawshad Arslan↗
DOE OSTI2022

Chemical kinetic interactions of NO with a multi-component gasoline surrogate: Experiments and modeling

Here this work reports an experimental and modeling study on the chemical kinetic interactions of NO with a multi-component gasoline surrogate, namely PACE-20, using a twin-piston rapid compression machine at a stochiometric fuel loading with 20% EGR (exhaust gas recirculation) by mass, pressures of 20 and 40 bar, and temperatures from 700 to 930 K. Five NO concentrations are investigated, namely 0, 20, 50, 70 and 150 ppm, where NO addition effects are characterized through changes in PACE-20 ignition reactivity and heat release characteristics. Experiments indicate that within the low-temperature regime, NO promotes low-temperature heat release rate and main ignition reactivity at low addition levels, with saturation or even inhibiting effects observed at >50 ppm NO addition, while within the NTC/intermediate-temperature regime, adding NO only promotes reactivity. A recently updated, detailed chemical kinetic model with chemistry specific to NOx/hydrocarbons interaction incorporated is used to simulate the experiments, and reasonable agreement is obtained. In-depth sensitivity and rate of production analyses are further performed. The results indicate that NO interacts with PACE-20 via two types of interaction: (a) direct interactions between NO and PACE-20 derivatives, primarily through NO+HO 2 ↔NO 2 +OH and RO 2 +NO↔RO+NO 2 , and (b) indirect interactions between PACE-20 derivatives and NO 2 produced from the direct interactions, primarily through R+NO 2 ↔RO+NO. The observed NO inhibiting effect at low temperatures and 150 ppm NO addition is attributed to the lack of HO 2 radicals to sustain NO consumption via NO+HO 2 ↔NO 2 +OH, and the take-up of inhibiting pathways via RO 2 +NO↔RO+NO 2 . The results also indicate that even with the presence of multiple fuel components, NOx/hydrocarbons interactions are highly selective, and are mainly initiated by the interactions between NO and RO 2 radicals from cyclopentane and ethanol, as well as between NO 2 and R radicals from toluene, 1,2,4-trimethylbenzene and 1-hexene. Further studies on these interactive reactions are therefore highly recommended.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Symbolic construction of the chemical Jacobian of quasi-steady state (QSS) chemistries for Exascale computing platforms

The Quasi-Steady State Approximation (QSSA) can be an effective tool for reducing the size and stiffness of chemical mechanisms for implementation in computational reacting flow solvers. However, for many applications, the resulting model still requires implicit methods for efficient time integration. Here, in this paper, we outline an approach to formulating the QSSA reduction that is coupled with a strategy to generate C++ source code to evaluate the net species production rates, and the chemical Jacobian. The code-generation component employs a symbolic approach enabling a simple and effective strategy to analytically compute the chemical Jacobian. For computational tractability, the symbolic approach needs to be paired with common subexpression elimination which can negatively affect memory usage. Several solutions are outlined and successfully tested on a 3D multipulse ignition problem, thus allowing portable application across chemical model sizes and GPU capabilities. The implementation of the proposed method is available at https://github.com/AMReX-Combustion/PelePhysics under an open-source license.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Probabilistic Resilience-Oriented Assessment Approach for Transmission Networks Under Wildfires

The rising threat of wildfires poses significant challenges to power transmission networks, particularly in areas prone to such disasters. Traditional approaches for wildfire risk assessment neglect some potential wildfire scenarios. Here, this paper introduces a probabilistic resilience-oriented assessment approach for power transmission networks to address this gap. Initially, a probabilistic wildfire model is developed to capture uncertainties in ignition, intensity, and fire spread. Next, a spatiotemporal fragility model is constructed to assess the impact of wildfires on transmission corridors, incorporating Thermal Aging (TA) and Dynamic Thermal Rate (DTR) change. Finally, a comprehensive resilience metric is defined to evaluate system performance, leveraging the fragility model to determine component and system-level resilience. The approach employs a combinatorial enumeration method to generate potential wildfire scenarios, enhanced by an impact-increment-based state enumeration (IISE) method for computational efficiency. The proposed method provides critical insights for identifying system vulnerabilities and developing robust strategies to protect transmission networks from wildfires. The efficacy of this approach is validated through extensive scenarios of the RTS-GMLC system across Southern California, Nevada and Arizona.

Vahedi, Soroush [Univ. of Connecticut, Storrs, CT ↗
DOE OSTI2024

Light Duty Engine Performance Characteristics with Dimethyl Ether and Propane

Here, this paper explores the performance characteristics of a compression ignition HYUNDAI 2.2L engine operating with Dimethyl Ether (DME). Test are carried out at three operating conditions that weigh heavily in the FTP75 certification cycle (1000rpm-12Nm, 1500rpm-50Nm, 2000rpm-100Nm). The engine features a high-pressure common rail fuel injection system designed to operate with liquified gases. The main component of the fuel system is a high-pressure pump that incorporates an electronic inlet metering valve commanded on a crank-angle base to control the rail pressure. The pump, which requires no pressure regulator, provides the flow needed to the injectors without flow returning to the inlet. This novel fueling system is leveraged in tests that are conducted to examine the impact of EGR, combustion phasing, injection pressure on efficiency and emissions. In addition, the impact of introducing 15% Propane by mass is examined. During the tests, the engine ECU is aided by an Engine Controller High Speed Oversight unit (ECHO) to provide combustion phasing control, improved cylinder-to-cylinder uniformity, and an effective optimization over the testing effort. The use of DME and Propane allowed for peak thermal efficiency of nearly 43%. These fuels enable significant carbon index (CI) reductions over the baseline Diesel fuel, with indications that 50% reduction in CO 2 over the Diesel engine are possible.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Magnetostrictive materials for enhanced sensors and electronic components

Magnetostriction is a property of magnetic materials that causes them to change their shape or dimensions when their magnetization changes. Low-cost, mechanically robust magnetostrictive sensors would be valuable for a wide range of applications addressing DOE's energy, environmental, and national security missions. Several examples include monitoring internal conditions of pipelines, enhancing implantable systems for the human body, and improving the electrical grid by providing real time sensors for detecting high impedance faults that may act as ignition sources for forest fires. Historically, magnetostrictive materials tended to be expensive and mechanically brittle, but recent developments in iron-based alloys, especially those that include dilute solutions of rare earth elements, have demonstrated useful magnetostriction values, mechanical robustness, and low costs. This project investigated addition of dilute cerium doping on the magnetostrictive properties of Fe-Ga and Fe-Al alloys. Advanced manufacturing techniques were applied to these materials to take advantage of rapid cooling of the alloy to stabilize desired phases and to make near net shape coupons. These coupons develop significant texturing, offering a route to target microstructures with exceptional performance.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Iron and Phosphorus Geochemistry in High-Centered and Low-Centered Polygon Soils from the Barrow Environmental Observatory, Utqiagvik, Alaska, 2015

This dataset provides chemical characterization of soil cores obtained in triplicate from center and trough positions of a high-centered polygon and center, ridge, and trough positions of a low-centered polygon in the NGEE Arctic research area within the Barrow Environmental Observatory, Utqiagvik, Alaska. Photographs of the 15 collected cores are provided. Cores were collected to thaw depth in early October 2015 and subsequently divided into subsamples for analysis, which included bulk soil horizons (organic or mineral) and finer scale depth increments (minimum 4 cm thickness per increment). Bulk horizons and depth increments were characterized using sequential chemical extractions for Fe and P and with Fe K-edge x-ray absorption spectroscopy. Additional soil parameters such as loss-on-ignition, gravimetric water content, and carbon and nitrogen concentrations were also quantified for bulk horizons. This dataset includes four csv files, one pdf user guide, and one zip folder of *.jpg photos.The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research.The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska.Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Ultra-compact system for characterization of physical, chemical and ignition properties of fuels

The present disclosure relates to a miniaturized fuel laboratory system that makes use of a housing, a processor housed within the housing, and a fuel inlet port supported from the housing for receiving a quantity of fuel to be used as a fuel test sample. The system may also have at least one fuel sensor housed in the housing in communication with the fuel inlet port for receiving the fuel test sample and carrying out combustion thereof. An electronic component may be housed in the housing, which enables communication with an external remote subsystem. A database may be incorporated which contains at least one of stored fuel characteristics or stored fuel analysis models, accessible by the processor. The processor may use fuel oxidation information generated by the fuel sensor, and at least one of the stored fuel characteristics or stored combustion models, to determine at least one fuel characteristic of the fuel test sample.

McNenly, Matthew J.↗
DOE OSTI2021

Fuel properties effects on wall-wetting and fuel-in-lube dilution under stochastic pre ignition prone conditions

Fuel-engine interactions have been shown to influence stochastic pre-ignition (SPI), however there is uncertainty on the root causes, participially if effects are primarily physical or chemical in nature. To better delineate the physical and chemical dependencies of fuel properties on SPI, this work studies interactions between aromatics, distillation, and particle matter index on SPI with a laser induced fluorescence (LIF) diagnostic to observe wall wetting. Fuels with high aromatic components or higher distillation temperatures tend to increase SPI events, but it is not well understood if the increased fuel dilution or a chemical aspect of this process is the primary mechanism for SPI. By employing the novel LIF in this work we measure fuel dilution in real-time in a running single cylinder research engine operated at SPI conditions. Three fuels were used in the present work, with the LIF diagnostic. Each fuel was operated at two injection timings, generating fuel specific effects on wall wetting. The LIF measurements are coupled with engine combustion measurements and SPI event counts. Results enable a deconvolution of fuel physical and chemical properties on SPI propensity, providing unique and novel insights into the dominant fuel effects affecting SPI.

Splitter, Derek↗
DOE OSTI2023

A co-kurtosis PCA based dimensionality reduction with nonlinear reconstruction using neural networks

For turbulent reacting flow systems, identification of low-dimensional representations of the thermo-chemical state space is vitally important, primarily to significantly reduce the computational cost of device-scale simulations. Principal component analysis (PCA), and its variants, are a widely employed class of methods. Recently, an alternative technique that focuses on higher-order statistical interactions, co-kurtosis PCA (CoK-PCA), has been shown to effectively provide a low-dimensional representation by capturing the stiff chemical dynamics associated with spatiotemporally localized reaction zones. While its effectiveness has only been demonstrated based on a priori analyses with linear reconstruction, in this work, we employ nonlinear techniques to reconstruct the full thermo-chemical state and evaluate the efficacy of CoK-PCA compared to PCA. Specifically, we combine a CoK-PCA-/PCA-based dimensionality reduction (encoding) with an artificial neural network (ANN) based reconstruction (decoding) and examine, a priori, the reconstruction errors of the thermo-chemical state. In addition, we evaluate the errors in species production rates and heat release rates, which are nonlinear functions of the reconstructed state, as a measure of the overall accuracy of the dimensionality reduction technique. We employ four datasets to assess CoK-PCA/PCA coupled with ANN-based reconstruction: zero-dimensional (homogeneous) reactor for autoignition of an ethylene/air mixture that has conventional single-stage ignition kinetics, a dimethyl ether (DME)/air mixture which has two-stage (low and high temperature) ignition kinetics, a one-dimensional freely propagating premixed ethylene/air laminar flame, and a two-dimensional dataset representing turbulent autoignition of ethanol in a homogeneous charge compression ignition (HCCI) engine. Finally, results from the analyses demonstrate the robustness of the CoK-PCA based low-dimensional manifold with ANN reconstruction in accurately capturing the data, specifically from the reaction zones.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗