Search NASA⌕ Search

SEARCH · Search NASA

Results for “in situ neutron diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Transient Phase-Driven Cyclic Deformation in Additively Manufactured 15-5 PH Steel

The present work extends the examination of selective laser melting (SLM)-fabricated 15-5 PH steel with the 8%-transient-austenite-phase towards fully-reversed strain-controlled low-cycle fatigue (LCF) test. The cyclic-deformation response and microstructural evolution were investigated via in-situ neutron-diffraction measurements. The transient-austenite-phase rapidly transformed into the martensite phase in the initial cyclic-hardening stage, followed by an almost complete martensitic transformation in the cyclic-softening and steady stage. The compressive stress was much greater than the tensile stress at the same strain amplitude. The enhanced martensitic transformation associated with lower dislocation densities under compression predominantly governed such a striking tension-compression asymmetry in the SLM-built 15-5 PH.

15-5 PH stainless steel↗
DOE OSTI2021

High Ammonia Adsorption in MFM-300 Materials: Dynamics and Charge Transfer in Host–Guest Binding

Ammonia (NH 3 ) is a promising energy resource owing to its high hydrogen density. However, its widespread application is restricted by the lack of efficient and corrosion-resistant storage materials. In this work, we report high NH 3 adsorption in a series of robust metal-organic framework (MOF) materials, MFM-300(M) (M = Fe, V, Cr, In). MFM-300(M) (M = Fe, V III , Cr) show fully reversible capacity for >20 cycles, reaching capacities of 16.1, 15.6, and 14.0 mmol g -1 , respectively, at 273 K and 1 bar. Under the same conditions, MFM-300(V IV ) exhibits the highest uptake among this series of MOFs of 17.3 mmol g -1 . In situ neutron powder diffraction, single-crystal X-ray diffraction, and electron paramagnetic resonance spectroscopy confirm that the redox-active V center enables host-guest charge transfer, with V IV being reduced to V III and NH 3 being oxidized to hydrazine (N 2 H 4 ). A combination of in situ inelastic neutron scattering and DFT modeling has revealed the binding dynamics of adsorbed NH 3 within these MOFs to afford a comprehensive insight into the application of MOF materials to the adsorption and conversion of NH 3 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2004

High Pressure X-Ray Diffraction Studies of Nanocrystalline Materials

Experimental evidence obtained for a variety of nanocrystalline materials suggest that the crystallographic structure of a very small size particle deviates from that in the bulk crystals. In this paper we show the effect of the surface of nanocrystals on their structure by the analysis of generation and distribution of macro- and micro-strains at high pressures and their dependence on the grain size in nanocrystalline powders of Sic. We studied the structure of Sic nanocrystals by in-situ high-pressure powder diffraction technique using synchrotron and neutron sources and hydrostatic or isostatic pressure conditions. The diffraction measurements were done in HASYLAB at DESY using a Diamond Anvil Cell (DAC) in the energy dispersive geometry in the diffraction vector range up to 3.5 - 4/A and under pressures up to 50 GPa at room temperature. In-situ high pressure neutron diffraction measurements were done at LANSCE in Los Alamos National Laboratory using the HIPD and HIPPO diffractometers with the Paris-Edinburgh and TAP-98 cells, respectively, in the diffraction vector range up to 26 Examination of the response of the material to external stresses requires nonstandard methodology of the materials characterization and description. Although every diffraction pattern contains a complete information on macro- and micro-strains, a high pressure experiment can reveal only those factors which contribute to the characteristic diffraction patterns of the crystalline phases present in the sample. The elastic properties of powders with the grain size from several nm to micrometers were examined using three methodologies: (l), the analysis of positions and widths of individual Bragg reflections (used for calculating macro- and micro-strains generated during densification) [I], (2). the analysis of the dependence of the experimental apparent lattice parameter, alp, on the diffraction vector Q [2], and (3), the atomic Pair Distribution Function (PDF) technique [3]. The results of our studies show, that Sic nanocrystals have the features of two phases, each with its distinct elastic properties. and under pressures up to 8 GPa.

Palosz, B.↗
DOE OSTI2023

Deformation, dislocation evolution and the non-Schmid effect in body-centered-cubic single- and polycrystal tantalum

A physically-informed continuum crystal plasticity model is presented to elucidate deformation mechanisms, dislocation evolution and the non-Schmid effect in body-centered-cubic (bcc) tantalum widely used as a key structural material for mechanical and thermal extremes. We show the unified structural modeling framework informed by mesoscopic dislocation dynamics simulations is capable of capturing salient features of the large inelastic behavior of tantalum at quasi-static (10 -3 s -1 ) to extreme strain rates (5000 s -1 ) and at low (77 K) to high temperatures (873 K) at both single- and polycrystal levels. Here we also present predictive capabilities of the model for microstructural evolution in the material. To this end, we investigate the effects of dislocation interactions on slip activities, instability and the non-Schmid behavior at the single crystal level. Furthermore, ex situ measurements on crystallographic texture evolution and dislocation density growth are carried out for polycrystal tantalum specimens at increasing strains. Numerical simulation results also support that the modeling framework is capable of capturing the main features of the polycrystal behavior over a wide range of strains, strain rates and temperatures. The theoretical, experimental and numerical results at both single- and polycrystal levels provide critical insight into the underlying physical pictures for micro- and macroscopic responses and their relations in this important class of refractory bcc materials undergoing large inelastic deformations.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Unraveling transition-metal-mediated stability of spinel oxide via in situ neutron scattering

The energy materials performance is intrinsically determined by structures from the average lattice structure to the atom arrangement, valence, and distribution of the containing transition metal (TM) elements. Understanding the mechanism of the structure transition and atom rearrangement via synthesis or processing is key to expediting the exploration of excellent energy materials. In this work, in situ neutron scattering is employed to reveal the real-time structure evolution, including the TM-O bonds, lattice, TM valence and the migration of the high-voltage spinel cathode LiNi 0.5 Mn 1.5 O 4 . The transition-metal-mediated spinel destabilization under the annealing at the oxygen-deficient atmosphere is pinpointed. Additionally, the formation of Mn 3+ is correlated to the TM migration activation, TM disordered rearrangement in the spinel, and the transition to a layered-rocksalt phase. The further TM interdiffusion and Mn 2+ reduction are also revealed with multi-stage thermodynamics and kinetics. The mechanisms of phase transition and atom migrations as functions of temperature, time and atmosphere present important guidance on the synthesis in various-valence element containing oxides.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Observation of an Intermediate to H 2 Binding in a Metal–Organic Framework

Coordinatively unsaturated metal sites within certain zeolites and metal–organic frameworks can strongly adsorb a wide array of substrates. While many classical examples involve electron-poor metal cations that interact with adsorbates largely through physical interactions, unsaturated electron-rich metal centers housed within porous frameworks can often chemisorb guests amenable to redox activity or covalent bond formation. Despite the promise that materials bearing such sites hold in addressing myriad challenges in gas separations and storage, very few studies have directly interrogated mechanisms of chemisorption at open metal sites within porous frameworks. Here, we show that nondissociative chemisorption of H 2 at the trigonal pyramidal Cu + sites in the metal–organic framework Cu I -MFU- 4 l occurs via the intermediacy of a metastable physisorbed precursor species. In situ powder neutron diffraction experiments enable crystallographic characterization of this intermediate, the first time that this has been accomplished for any material. Evidence for a precursor intermediate is also afforded from temperature-programmed desorption and density functional theory calculations. Here, the activation barrier separating the precursor species from the chemisorbed state is shown to correlate with a change in the Cu + coordination environment that enhances p-backbonding with H 2 . Ultimately, these findings demonstrate that adsorption at framework metal sites does not always follow a concerted pathway and underscore the importance of probing kinetics in the design of next-generation adsorbents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Pore Distortion in a Metal–Organic Framework for Regulated Separation of Propane and Propylene

The development of porous solids for adsorptive separation of propylene and propane remains an important and challenging line of research. State-of-the-art sorbent materials often suffer from the trade-off between adsorption capacity and selectivity. Here, we report the regulated separation of propylene and propane in a metal–organic framework via designed pore distortion. Here, the distorted pore structure of HIAM-301 successfully excludes propane and thus achieved simultaneously high selectivity (>150) and large capacity (~3.2 mmol/g) of propylene at 298 K and 1 bar. Dynamic breakthrough measurements validated the excellent separation of propane and propylene. In situ neutron powder diffraction and inelastic neutron scattering revealed the binding domains of adsorbed propylene molecules in HIAM-301 as well as host–guest interaction dynamics. This study presents a new benchmark for the adsorptive separation of propylene and propane.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Direct Observation of Ammonia Storage in UiO-66 Incorporating Cu(II) Binding Sites

The presence of active sites in metal–organic framework (MOF) materials can control and affect their performance significantly in adsorption and catalysis. However, revealing the interactions between the substrate and active sites in MOFs at atomic precision remains a challenging task. Here, we report the direct observation of binding of NH 3 in a series of UiO-66 materials containing atomically dispersed defects and open Cu(I) and Cu(II) sites. While all MOFs in this series exhibit similar surface areas (1111–1135 m 2 g –1 ), decoration of the -OH site in UiO-66-defect with Cu(II) results in a 43% enhancement of the isothermal uptake of NH 3 at 273 K and 1.0 bar from 11.8 in UiO-66-defect to 16.9 mmol g –1 in UiO-66-Cu II . A 100% enhancement of dynamic adsorption of NH 3 at a concentration level of 630 ppm from 2.07 mmol g –1 in UiO-66-defect to 4.15 mmol g –1 in UiO-66-Cu II at 298 K is observed. In situ neutron powder diffraction, inelastic neutron scattering, and electron paramagnetic resonance, solid-state nuclear magnetic resonance, and infrared spectroscopies, coupled with modeling reveal that the enhanced NH 3 uptake in UiO-66-Cu II originates from a {Cu(II)···NH 3 } interaction, with a reversible change in geometry at Cu(II) from near-linear to trigonal coordination. This work represents the first example of structural elucidation of NH 3 binding in MOFs containing open metal sites and will inform the design of new efficient MOF sorbents by targeted control of active sites for NH 3 capture and storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Direct Conversion of Methane to Ethylene and Acetylene over an Iron-Based Metal–Organic Framework

Conversion of methane (CH 4 ) to ethylene (C 2 H 4 ) and/or acetylene (C 2 H 2 ) enables routes to a wide range of products directly from natural gas. However, high reaction temperatures and pressures are often required to activate and convert CH 4 controllably, and separating C 2+ products from unreacted CH 4 can be challenging. Here, we report the direct conversion of CH 4 to C 2 H 4 and C 2 H 2 driven by non-thermal plasma under ambient (25 °C and 1 atm) and flow conditions over a metal–organic framework material, MFM-300(Fe). The selectivity for the formation of C 2 H 4 and C 2 H 2 reaches 96% with a high time yield of 334 μmol g cat –1 h –1 . At a conversion of 10%, the selectivity to C 2+ hydrocarbons and time yield exceed 98% and 2056 μmol g cat –1 h –1 , respectively, representing a new benchmark for conversion of CH 4 . In situ neutron powder diffraction, inelastic neutron scattering and solid-state nuclear magnetic resonance, electron paramagnetic resonance (EPR), and diffuse reflectance infrared Fourier transform spectroscopies, coupled with modeling studies, reveal the crucial role of Fe–O(H)–Fe sites in activating CH 4 and stabilizing reaction intermediates via the formation of an Fe–O(CH 3 )–Fe adduct. In addition, a cascade fixed-bed system has been developed to achieve online separation of C 2 H 4 and C 2 H 2 from unreacted CH 4 for direct use. Integrating the processes of CH 4 activation, conversion, and product separation within one system opens a new avenue for natural gas utility, bridging the gap between fundamental studies and practical applications in this area.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Hydrogen Storage with Aluminum Formate, ALF: Experimental, Computational, and Technoeconomic Studies

Long-duration storage of hydrogen is necessary for coupling renewable H 2 with stationary fuel cell power applications. In this work, aluminum formate (ALF), which adopts the ReO 3 -type structure, is shown to have remarkable H 2 storage performance at non-cryogenic (>120 K) temperatures and low pressures. The most promising performance of ALF is found between 120 K and 160 K and at 10 bar to 20 bar. The study illustrates H 2 adsorption performance of ALF over the 77 K to 296 K temperature range using gas isotherms, in situ neutron powder diffraction, and DFT calculations, as well as technoeconomic analysis (TEA), illustrating ALF’s competitive performance for long-duration storage versus compressed hydrogen and leading metal–organic frameworks. In the TEA, it is shown that ALF’s storage capacity, when combined with a temperature/pressure swing process, has advantages versus compressed H 2 at a fraction of the pressure (15 bar versus 350 bar). In conclusion, given ALF’s performance in the 10 bar to 20 bar regime under moderate cooling, it is particularly promising for use in safe storage systems serving fuel cells.

08 HYDROGEN↗
DOE OSTI2021

Strength can be controlled by edge dislocations in refractory high-entropy alloys

Energy efficiency is motivating the search for new high-temperature (high-T) metals. Some new body-centered-cubic (BCC) random multicomponent “high-entropy alloys (HEAs)” based on refractory elements (Cr-Mo-Nb-Ta-V-W-Hf-Ti-Zr) possess exceptional strengths at high temperatures but the physical origins of this outstanding behavior are not known. Here we show, using integrated in-situ neutron-diffraction (ND), high-resolution transmission electron microscopy (HRTEM), and recent theory, that the high strength and strength retention of a NbTaTiV alloy and a high-strength/low-density CrMoNbV alloy are attributable to edge dislocations. This finding is surprising because plastic flows in BCC elemental metals and dilute alloys are generally controlled by screw dislocations. We use the insight and theory to perform a computationally-guided search over 10 7 BCC HEAs and identify over 10 6 possible ultra-strong high-T alloy compositions for future exploration.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High capacity ammonia adsorption in a robust metal–organic framework mediated by reversible host–guest interactions

To understand the exceptional adsorption of ammonia (NH 3 ) in MFM-300(Sc) (19.5 mmol g -1 at 273 K and 1 bar without hysteresis), we report a systematic investigation of the mechanism of adsorption by a combination of in situ neutron powder diffraction, inelastic neutron scattering, synchrotron infrared microspectroscopy, and solid-state 45 Sc NMR spectroscopy. These complementary techniques reveal the formation of reversible host–guest supramolecular interactions, which explains directly the observed excellent reversibility of this material over 90 adsorption–desorption cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Hydrogen Storage with Aluminum Formate, ALF: Experimental, Computational, and Technoeconomic Studies

Long-duration storage of hydrogen is necessary for coupling renewable H2 with stationary fuel cell power applications. In this presentation, I will discuss how aluminum formate, Al(HCOO)3 (ALF), which adopts an ReO3-type structure, is shown to have remarkable H2 storage performance at non-cryogenic (> 120 K) temperatures and low pressures. The most promising performance of ALF is found between 120 K and 160 K and at 10 bar to 20 bar. The talk will cover and illustrate the H2 adsorption performance of ALF over the 77 K to 296 K temperature range using gas isotherms, in situ neutron powder diffraction, and DFT calculations, as well as technoeconomic analysis (TEA), illustrating ALF’s competitive performance for long-duration storage versus compressed hydrogen and leading metal–organic frameworks. In the TEA, it is shown that ALF’s storage capacity, when combined with a temperature/pressure swing process, has advantages versus compressed H2 at a fraction of the pressure (15 bar versus 350 bar). Given ALF’s performance in the 10 bar to 20 bar regime under moderate cooling, it is particularly promising for use in safe storage systems serving fuel cells, and is currently the only MOF that works in this moderate temperature range/ low pressure regime to be cost competitive with compressed H2 gas for large scale H2 storage.[1]

Chemistry↗
DOE OSTI2023

Combined, time-resolved, in situ neutron reflectometry and X-ray diffraction analysis of dynamic SEI formation during electrochemical N 2 reduction

One means of improving performance for electrochemical ammonia production through the Li-mediated N 2 reduction reaction (Li-NRR) is by cycling the current driving the reaction between open-circuit conditions and periods of applied current density. Herein, we have investigated the dynamics of the electrode–electrolyte interface under Li-NRR conditions during current cycling using in situ time-resolved neutron reflectometry and grazing-incidence synchrotron X-ray diffraction. During cycling, measured neutron reflectivity curves indicated bilayer formation in which Li-containing species such as LiOH, Li 2 O, and small quantities of Li 3 N and metallic Li primarily appeared in a thin layer at the cathode surface, above which formed a much larger, porous, ‘solid–electrolyte interface’ (SEI) layer. Upon return to open-circuit conditions, Li-containing species quickly moved out of the thin layer, leaving a compact, stable layer of decomposition products underneath the SEI layer. This SEI layer concomitantly filled with electrolyte or dissolved, becoming indistinguishable from the electrolyte via contrast in scattering-length density (SLD). During the second current cycle, Li-containing species again preferentially deposited directly atop the cathode, with the thick SEI-like layer again appearing within a minute. This SEI layer exhibited a lower SLD more quickly than in the first cycle, which might suggest that Li-containing species become distributed within the porous SEI layer. Furthermore, these time-resolved observations of SEI and plated layers during current cycling suggest that benefits associated with return to open-circuit conditions between periods of applied current density may be related to the concomitant loss of Li-containing species from a thin layer at the cathode surface into a porous SEI layer that becomes filled with electrolyte or dissolves.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗