Search NASA⌕ Search

SEARCH · Search NASA

Results for “ink formulation and processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Particle Migration in Large Cross-Section Ceramic On-Demand Extrusion Components

Ceramic On-Demand Extrusion (CODE) is a direct ink writing process which allows for the creation of near theoretically dense ceramic components with large cross-sections due to oil-assisted drying. Here, Yttria-stabilized zirconia (YSZ) colloidal pastes were used in CODE to produce dense (multi-road infill and ≳ 98% relative density), large continuous volume (> 1 cm 3 ), and high fidelity (nozzle diameters ≲ 1 mm) structural ceramic components with nanoparticle feedstocks (~d 50 ≲ 1 µm). However, many of these printed components underwent significant particle migration after forming. The reason for this particle migration defect was investigated using the coffee-ring effect for dilute solutions and rheological methods for dense suspensions. Modifications to the colloidal paste, such as changes in solids loading, pH, or surfactant concentration were explored as to their effectiveness to mitigate the defect. Ultimately, paste formulation and printing trade-offs are discussed with respect to the post-printing defect and as to general direct-write patterning.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Shelf-life of ball-milled catalyst inks for the fabrication of fuel cell electrodes

A major factor driving fuel cell costs is the quantity of precious metal required. Therefore, it is important to understand a timeframe where inks can be reused. Here, in this work, we explore differences between a freshly prepared catalyst ink and one that has been stored for over a year – comparing ink properties, cathode catalyst layer microstructure, and their respective fuel cell performance. Ink studies revealed smaller agglomerate sizes and a decrease in shear viscosity for the aged ink. Longer storage time also results in fewer cracks and a more uniform ionomer distribution, as evidenced by microscopy characterization of rod-coated electrodes. Lastly, polarization curves show improved performance at higher current densities for the electrode prepared from the aged ink. We rationalize such effect in terms of enhanced ionomer adsorption onto the catalyst over time.

08 HYDROGEN↗
DOE OSTI2021

3D Printing of Transparent Silicone Elastomers

Here in this paper, inks for transparent elastomers that are formulated by matching the refractive index of silica and polysiloxanes are described. The transparent inks transmit up to ≈90% of 700 nm light through 1 cm and remain transparent when solidified. The inks and solidified materials exhibit a thermochromic effect. This thermochromic effect can be controlled by the refractive index mismatch. Transparency may increase or decrease as temperature increases, depending on the refractive index mismatch of the base polysiloxane and silica. It is found that the rheological properties of the ink depend on the distribution of silica particles, which is dictated by silica functionality, weight content, and processing. Siloxane precursors that vary in chemical functionality are introduced to tailor the mechanical properties of the printed elastomers, which obtain stretchability >65% along with a tensile modulus of 1.9 MPa. After optimizing siloxane chemistry and ink processing, the authors are able to print transparent elastomers. Potential applications are demonstrated for printed structures by printing encapsulation structures for light-emitting diodes, semitransparent dye-filled structures, a microfluidic mixing device, and a multimaterial structure that exhibits temperature-dependent camouflage.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The influence of electrode crack dimensions on the durability of polymer electrolyte membrane fuel cells

Electrode cracks in polymer electrolyte membrane fuel cells (PEMFCs) are correlated with early onset failures. Here, in this work we investigate the influence of cracked gas diffusion electrodes (GDEs) on the durability of the membrane electrode assembly (MEA) using a combined chemical-mechanical accelerated stress test (AST). Electrode crack dimensions were systematically tuned using ink formulations and material selection strategies. A parameter to describe the crack width areal density (Φ CW ) was used to quantify the degree of discontinuity in the electrode surfaces. Open circuit voltage (OCV) transient analyses were used to benchmark and characterize the failure mechanisms in the MEAs as a function of the Φ CW . While smaller electrode-level cracks, on the order of microns, yielded a 28 % decrease in operating lifetime, larger cracks that propagated from a discontinuous, microporous layer (MPL) coating, decreased the operating lifetime by 56 %. This work emphasizes the need for material processing strategies that consider defect tolerances to limit membrane failures in PEMFCs.

08 HYDROGEN↗
DOE OSTI2022

Catalyst layer formulations for slot-die coating of PEM fuel cell electrodes

The series of electrodes were fabricated by the scalable and manufacturable slot-die coating method for proton exchange membrane fuel cell (PEMFC) application. The inks with different amounts of solids were studied by rheological methods in order to establish a coating window with minimum manufacturing defects. The obtained electrodes were characterized by SEM, AFM, and optical microscopy, which showed that they were uniform and homogeneous with minimum defects. The electrochemical evaluation of the manufactured gas diffusion electrodes (GDE) showed that the main characteristics of the electrodes, like electrochemical surface area, proton resistivity, and double layer capacitance, were found to be close for all samples confirming the reproducibility of the slot-die process. Additionally, we studied the effects of membrane thickness on the performance of the GDE membrane electrode assemblies and determined that a decrease in membrane thickness favored the performance. Furthermore, the obtained results clearly demonstrated the applicability and feasibility of the approach for the Manufacturing of catalyst layers for the fuel cell application with potential for future mass production.

08 HYDROGEN↗
DOE OSTI2025

Multimaterial 3D Printing in Activating Bath Enables In Situ Polymerization of Thermosets with Intricate Geometries and Diverse Elastic Behaviors

Polydicyclopentadiene, p(DCPD), is a high‐performance thermoset valued for its exceptional toughness, strength, and stiffness. When copolymerized with 1,5‐cyclooctadiene (COD), its mechanical properties can be tuned from glassy to rubbery at room temperature. While frontal polymerization enables a rapid and energy‐efficient route to 3D print DCPD‐based materials, challenges such as ink shelf life and gravitational distortion, especially in direct ink writing of soft COD‐rich formulations, must be considered. Here, a complementary chemical strategy is presented, embedded 3D printing, that enables localized in situ polymerization of printed DCPD/COD inks within a reactive support matrix. The matrix provides both physical support and a reservoir of chemical activator, which diffuses into the ink, activates a latent bis(N‐heterocyclic carbene) Ru precatalyst, and initiates ring‐opening metathesis polymerization. Curing begins at the ink–matrix interface and propagates inward via diffusion, stabilizing the interface and preventing capillary‐driven deformation regardless of the matrix yield stress. This approach eliminates the need for cold storage, external curing, or photoinitiation, significantly expanding the processing window. Using this method, diverse thermosetting and elastomeric architectures are fabricated with features as small as 5 µm and aspect ratios of 100, including interlinked chains, shallow spherical shells exhibiting snap‐through buckling, and hair‐like fin arrays inaccessible through traditional techniques.

chemical activation↗
DOE OSTI2019

Optimal design of fiber reinforced composite structures and their direct ink write fabrication

The majority of the current structural optimization software does not accommodate manufacturing constraints. Therefore, substantial modifications are imposed upon optimized designs to make them manufacturable and hence nonoptimal. We propose to optimize the design of composite structures that are amenable to Additive Manufacturing (AM). The printing process chosen in our study is based on Direct Ink Writing (DIW) in which short carbon fibers in a thermoset resin are extruded through a moving nozzle to build up a structure. Since the fibers are primarily aligned in the flow direction of the extrudate, the DIW printing trajectory influences the material properties of the composite structure. To accommodate this, the extrudate trajectory follows the contours of parameterized level-set functions. The parametrization allows us to prescribe the material properties and impose many DIW manufacturing constraints such as no-overlap, no-sag, minimum radius of curvature and continuity of the toolpaths. Ultimately, we obtain optimal manufacturable toolpaths that start and finish at a boundary. To minimize the fabrication time, we formulate the linking sequence of the toolpaths as a traveling salesman problem which we solve to obtain the shortest continuous toolpath per layer. Several examples illustrate the optimization procedure. Validation is also performed.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Molten-Metal Droplet Deposition on a Moving Substrate in Microgravity: Aiding the Development of Novel Technologies for Microelectronic Assembly

Driven by advancements in microelectronics manufacturing, this research investigates the oblique (non-axisymmetric) impact of liquid-metal droplets on flat substrates. The problem of interest is relevant to the development of the novel technology of on-demand dispension (printing) of microscopic solder deposits for the surface mounting of microelectronic devices. The technology, known as solder jetting, features on-demand deposition of miniature solder droplets (30 to 120 microns in diameter) in very fine, very accurate patterns using techniques analogous to those developed for the ink-jet printing industry. Despite its promise, severe limitations exist currently with regards to the throughput rates of the technology; some of these limitations are largely due to the lack of the capability for reliable prediction of solder bump positioning and shapes, especially under ballistic deposition conditions where the droplet impact phenomena are inherently three-dimensional. The study consists of a theoretical and an experimental component. The theoretical work uses a finite element formulation to simulate numerically the non-axisymmetric (3-D) fluid mechanics and heat transfer phenomena of a liquid solder droplet impacting at an angle alpha on a flat substrate. The work focuses on the pre-solidification regime. The modeling of the most challenging fluid mechanics part of the process has been completed successfully. It is based upon the full laminar Navier-Stokes equations employing a Lagrangian frame of reference. Due to the large droplet deformation, the surface (skin) as well as the volumetric mesh have to be regenerated during the calculations in order to maintain the high accuracy of the numerical scheme. The pressure and velocity fields are then interpolated on the newly created mesh. The numerical predictions are being tested against experiments, for cases where wetting phenomena are not important. For the impact parameters used in the example shown (We = 2.38, Fr = 16300, Re = 157), the droplet rolls along the substrate, but its shape remains practically axisymmetric for all impact angles within the range from 0 to 60 deg. Interestingly, the substrate/droplet contact area during the recoiling phase of the impact is not a monotonically decreasing function of time. The experimental component of the research tests the numerical predictions and provides necessary input data (contact angles) for the theoretical model. The experiments are performed in microgravity (2.2s drop tower of the NASA GRC) in order to allow for the use of mm-size solder droplets, which make feasible the performance of accurate measurements, while maintaining similitude of the relevant fluid dynamic groups (Re, Fr, We, Ste). Preliminary oblique impact experiments have been performed using water droplets in normal gravity.

Megaridis, C. M.↗
DOE OSTI2019

Active Mixing of Reactive Materials for 3D Printing

The mixing of materials during additive manufacturing is a major benefit which allows one to compositionally and spatially tailor material properties, for example to locally control the reactivity in fuel–oxidizer systems known as thermites. This work characterizes an active mixing printhead used in conjunction with a 3D printing process known as Direct Ink Writing. Besides compositional control, a major benefit of this approach is that it offers a safe method for working with these materials, which can otherwise be hazardous once mixed. Custom fuel and oxidizer inks are fed at fixed volumetric rates into an active mixing printhead, and both the rotational speed of the mixing impeller as well as the fuel–oxidizer ratio are varied. Upon ignition, the propagation speed increases with the rotational speed of the mixer and plateaus above a critical value of ≈750 rpm. The critical mixing speed is corroborated by computational fluid simulations and an analytical expression that considers the inks’ complex fluid behavior. Additionally, varying the composition results in a wide range of propagation speeds with peak reactivity corresponding to a fuel–rich formulation ( Φ = 1.5). As a result, a test article incorporating a fast– and slow–burning region demonstrates how spatial composition can manipulate the reactivity.

3D printing↗
NASA NTRS2015

Solid State Ultracapacitor

NASA analyzes, tests, packages, and fabricates electrical, electronic, and electromechanical (EEE) parts used in space vehicles. One area that NASA wishes to advance is energy storage and delivery. Currently, space vehicles use rechargeable batteries that utilize silver zinc or lithium ion electrochemical processes. These current state-of-the-art rechargeable batteries cannot be rapidly charged, contain harmful chemicals, and suffer from early wear-out mechanisms. A solid state ultracapacitor is an EEE part that offers significant advantages over current electrochemical and electrolytic devices. The objective of this research is to develop an internal barrier layer ultracapacitor (IBLC) using novel dielectric materials as a battery replacement with a focus on these advantages: longer life, lower mass-toweight ratio, rapid charging, on-demand pulse power, improved on-pad standby time without maintenance, and environmental friendliness. The approach is unique in two areas. A deposition technique is used that has been shown to produce a more uniformly coated nanoparticle than sol-gel, which has resulted in colossal permittivities. These particles are then distributed in an ink formulation developed at NASA Marshall Space Flight Center (MSFC) and deposited utilizing a 3D aerosol jet technique. This additive manufacturing technique controls layer thickness, resulting in extremely large capacitance and energy density.

Rolin, Terry D.↗
DOE OSTI2021

Solvent absorption rate of perfluorosulphonic acid membranes towards understanding direct coating processes

Here we present a method for measurement of the rate of solvent absorption by perfluorosulfonic acid (PFSA) membranes using a force tensiometer. The method presented here can be used as a tool to understand solvent absorption and should provide a rationale for designing catalyst inks for direct coating processes since it is necessary to understand how the absorption rate – on a time scale of seconds to minutes – compares to the time scales of the coating process in order to minimize membrane swelling. This method allows for rapid screening of the absorption and swelling behavior of different solvents and mixtures. Using this method, the absorption of water/1-propanol mixtures were measured for three thicknesses of Nafion PFSA membrane – Nafion 1135, Nafion 115, and Nafion 117. We find that the absorption rate is dependent on the ratio of the solvents as well as the thickness of the membrane. The analysis indicates that the highest absorption rate occurs when the mass percentage of 1-propanol in the mixture is 50%, whereas the lowest rates are for pure water and 1-propanol. In addition, membrane distortion also occurs most quickly for the 50% 1-propanol mixture. Our results suggest that catalyst inks that are highly rich (=90%) in water or 1-propanol are likely best for direct coating as such formulations will minimize absorption and swelling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Roll to Roll (R2R) Manufacturing of Electrolysis Electrodes for Low Cost Hydrogen Production: Cooperative Research and Development Final Report, CRADA Number CRD-18-00780

NREL, Argonne National Laboratory (ANL) and Oak Ridge National Laboratory (ORNL), which are also referred to collectively herein as the "Contractors" will perform electrode ink development and characterization, focusing on 1) inks with appropriate properties for R2R (gravure and slot-die) coating onto PFSA membrane and 2) catalysts suitable for electrolysis. Participant will develop acceptance criteria and characterization methods for direct coating on the membrane. The purpose of this project is to show feasibility for cost reduction of the electrode through increased throughput and improved material utilization. Successful completion of this project will result in more affordable hydrogen production via proton exchange membrane (PEM) electrolysis by substantially reducing the anode precious metal content and catalyst-coated membrane processing costs. Assists laboratory in achieving programmatic scope, adds new capability to the laboratory's core competencies. This project uses and enhances the laboratory's core competencies, and enhances U.S. competitiveness by utilizing DOE developed intellectual property and/or capabilities. This project will benefit the Fuel Cell subprogram within the EERE Fuel Cell Technologies Office (FCTO) by actively developing materials, formulations, components, and processes for PEM electrolyzer stacks for overcoming critical technical barriers to widespread hydrogen production for zero-emission transportation applications. Through this JWS, NREL, ANL and ORNL are assisting a key domestic industry partner, Proton Energy Systems, Inc., in the area of low-cost electrolyzer electrode formulation and coating technology. After completion of this project, NREL, ANL and ORNL will be able to verify whether the direct deposit coating processes investigated are suitable for producing CCMs for PEM electrolyzers, which is of great interest and benefit to the DOE EERE Fuel Cell Technologies Office (FCTO) and H2@Scale missions.

08 HYDROGEN↗
DOE OSTI2022

All‐Printed Ultrahigh‐Responsivity MoS 2 Nanosheet Photodetectors Enabled by Megasonic Exfoliation

Abstract Printed 2D materials, derived from solution‐processed inks, offer scalable and cost‐effective routes to mechanically flexible optoelectronics. With micrometer‐scale control and broad processing latitude, aerosol‐jet printing (AJP) is of particular interest for all‐printed circuits and systems. Here, AJP is utilized to achieve ultrahigh‐responsivity photodetectors consisting of well‐aligned, percolating networks of semiconducting MoS 2 nanosheets and graphene electrodes on flexible polyimide substrates. Ultrathin (≈1.2 nm thick) and high‐aspect‐ratio (≈1 μm lateral size) MoS 2 nanosheets are obtained by electrochemical intercalation followed by megasonic atomization during AJP, which not only aerosolizes the inks but also further exfoliates the nanosheets. The incorporation of the high‐boiling‐point solvent terpineol into the MoS 2 ink is critical for achieving a highly aligned and flat thin‐film morphology following AJP as confirmed by grazing‐incidence wide‐angle X‐ray scattering and atomic force microscopy. Following AJP, curing is achieved with photonic annealing, which yields quasi‐ohmic contacts and photoactive channels with responsivities exceeding 10 3 A W −1 that outperform previously reported all‐printed visible‐light photodetectors by over three orders of magnitude. Megasonic exfoliation coupled with properly designed AJP ink formulations enables the superlative optoelectronic properties of ultrathin MoS 2 nanosheets to be preserved and exploited for the scalable additive manufacturing of mechanically flexible optoelectronics.

2D materials↗
DOE OSTI2024

Impact of polymer additives on crack mitigation of rod-coated fuel cell cathode catalyst layers

Cracks in catalyst layers (CLs) are a potential source of long-term failure in a fuel cell membrane electrode assembly (MEA). While modifications to the CL ink formulation can affect the degree of cracking, these changes may lead to lower initial performance than their cracked analogues due to the established link between formulation and performance. In this work, we explored the use of polymeric additives to mitigate CL cracks. Small quantities of poly (acrylic acid), poly (ethylene oxide), poly (methyl methacrylate), or poly (vinyl alcohol) - 5 wt% relative to ionomer mass - were added to the ink prior to its final mixing. Poly (vinyl alcohol) resulted in crack-free CLs, whereas the other polymers resulted in CLs with similar crack percentages as the control CL. Through a combination of transmission electron microscopy, X-ray computed tomography, and infrared spectroscopy, we ascribed the crack-mitigating mechanism of poly (vinyl alcohol) to its ability to hydrogen-bond with Nafion, the ion conducting polymer binder in the catalyst ink. Initial performance of this non-cracked electrode exhibited nearly identical electrochemical behavior to its cracked counterpart, demonstrating that PVA additives successfully reduce cracks while maintaining cell initial performance.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Colloidal Stability of PFSA-Ionomer Dispersions Part II: Determination of Suspension pH Using Single-Ion Potential Energies

Perfluorosulfonic acid (PFSA) ionomers serve a vital role in the performance and stability of fuel-cell catalyst layers. These properties, in turn, depend on the colloidal processing of precursor inks. Here, to understand the colloidal structure of fuel-cell catalyst layers, we explore the aggregation of PFSA ionomers dissolved in water/alcohol solutions and relate the predicted aggregation to experimental measurements of solution pH. Not all side chains contribute to measured pH because of burying inside particle aggregates. To account for the measured degree of dissociation, a new description is developed for how PFSA aggregates interact with each other. The developed single-counterion electrostatic repulsive pair potential from Part I is incorporated into the Smoluchowski collision-based kinetics of interacting aggregates with buried side chains. We demonstrate that the surrounding solvent mixture affects the degree of aggregation as well as the pH of the system primarily through the solution dielectric permittivity, which drives the strength of the interparticle repulsive energies. Successful pH prediction of Nafion ionomer dispersions in water/n-propanol solutions validates the numerical calculations. Nafion-dispersion pH measurements serve as a surrogate for Nafion particle-size distributions. The model and framework can be leveraged to explore different ink formulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A Review on Progress, Challenges, and Prospects of Material Jetting of Copper and Tungsten

Copper (Cu) and tungsten (W) possess exceptional electrical and thermal conductivity properties, making them suitable candidates for applications such as interconnects and thermal conductivity enhancements. Solution-based additive manufacturing (SBAM) offers unique advantages, including patterning capabilities, cost-effectiveness, and scalability among the various methods for manufacturing Cu and W-based films and structures. In particular, SBAM material jetting techniques, such as inkjet printing (IJP), direct ink writing (DIW), and aerosol jet printing (AJP), present a promising approach for design freedom, low material wastes, and versatility as either stand-alone printers or integrated with powder bed-based metal additive manufacturing (MAM). Thus, this review summarizes recent advancements in solution-processed Cu and W, focusing on IJP, DIW, and AJP techniques. The discussion encompasses general aspects, current status, challenges, and recent research highlights. Furthermore, this paper addresses integrating material jetting techniques with powder bed-based MAM to fabricate functional alloys and multi-material structures. Finally, the factors influencing large-scale fabrication and potential prospects in this area are explored.

36 MATERIALS SCIENCE↗
NASA NTRS2013

Conductive Carbon Nanotube Inks for Use with Desktop Inkjet Printing Technology

Inkjet printing is a common commercial process. In addition to the familiar use in printing documents from computers, it is also used in some industrial applications. For example, wire manufacturers are required by law to print the wire type, gauge, and safety information on the exterior of each foot of manufactured wire, and this is typically done with inkjet or laser printers. The goal of this work was the creation of conductive inks that can be applied to a wire or flexible substrates via inkjet printing methods. The use of inkjet printing technology to print conductive inks has been in testing for several years. While researchers have been able to get the printing system to mechanically work, the application of conductive inks on substrates has not consistently produced adequate low resistances in the kilohm range. Conductive materials can be applied using a printer in single or multiple passes onto a substrate including textiles, polymer films, and paper. The conductive materials are composed of electrical conductors such as carbon nanotubes (including functionalized carbon nanotubes and metal-coated carbon nanotubes); graphene, a polycyclic aromatic hydrocarbon (e.g., pentacene and bisperipentacene); metal nanoparticles; inherently conductive polymers (ICP); and combinations thereof. Once the conductive materials are applied, the materials are dried and sintered to form adherent conductive materials on the substrate. For certain formulations, increased conductivity can be achieved by printing on substrates supported by low levels of magnetic field alignment. The adherent conductive materials can be used in applications such as damage detection, dust particle removal, smart coating systems, and flexible electronic circuitry. By applying alternating layers of different electrical conductors to form a layered composite material, a single homogeneous layer can be produced with improved electrical properties. It is believed that patterning alternate layers of different conductors may improve electrical pathways through alignment of the conductors and band gap optimization. One feature of this innovation is that flexible conductive traces could be accomplished with a conductive ink having a surface resistivity of less than 10 ohms/square. Another result was that a composite material comprising a mixture of carbon nanotubes and metallic nanoparticles could be applied by inkjet printing to flexible substrates, and the resulting applied material was one to two orders of magnitude more conductive than a material made by printing inks containing carbon nanotubes alone.

Roberson, Luke↗
DOE OSTI2018

Thermodynamic Driving Force in the Spontaneous Formation of Inorganic Nanoparticle Solutions

Nanoparticles are the bridge between the molecular and the macroscopic worlds. The growing number of commercial applications for nanoparticles spans from consumer products to new frontiers of medicine and next-generation optoelectronic technology. They are most commonly deployed in the form of a colloid, or “ink”, which are formulated with solvents, surfactants, and electrolytes to kinetically prevent the solid particulate phase from reaching the thermodynamically favored state of separate solid and liquid phases. In this work, we theoretically determine the thermodynamic requirements for forming a single-phase solution of spherical particles and engineer a model system to experimentally demonstrate the spontaneous formation of solutions composed of only solvent and bare inorganic nanoparticles. We show molecular interactions at the nanoparticle interface are the driving force in high-concentration nanoparticle solutions. The work establishes a regime where inorganic nanoparticles behave as molecular solutes as opposed to kinetically stable colloids, which has far-reaching implications for the future design and deployment of nanomaterial technologies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗