Search NASA⌕ Search

SEARCH · Search NASA

Results for “interlayers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Adherence of sputtered titanium carbides

Sputtered coatings of the refractory metal carbides are of great interest for applications where hard wear-resistant materials are desired. The usefulness of sputtered refractory carbides is often limited, in practice, by spalling or interfacial separation. In this work improvements in the adherence of refractory carbides on iron, nickel and titanium based alloys were obtained by using oxidation, reactive sputtering or sputtered interlayers to alter the coating-substrate interfacial region. X-ray photoelectron spectroscopy and argon ion etching were used to characterize the interfacial regions, and an attempt was made to correlate adherence as measured in wear tests with the chemical nature of the interface.

Brainard, W. A.↗
NASA NTRS1978

Ceramic blade attachments

Studies under way on two concepts for producing a turbine rotor with ceramic blades and superalloy disks are discussed. One concept employs hot-pressed silicon nitride blades and a compliant interlayer at the blade root end fitting whereas the second concept relies on a superplastic plastic forging technique to attach ceramic blades to the metal disk. This latter concept has been hot spin tested at 2250 F and 45,000 RPM for 50 hours in a vacuum spin pit. The fully bladed (30 blades) rotor survived this major test.

Calvert, G. S.↗
NASA NTRS1979

Adherence of sputtered titanium carbides

The study searches for interface treatment that would increase the adhesion of TiC coating to nickel- and titanium-base alloys. Rene 41 (19 wt percent Cr, 11 wt percent Mo, 3 wt percent Ti, balance Ni) and Ti-6Al-4V (6 wt percent Al, 4 wt percent V, balance Ti) are considered. Adhesion of the coatings is evaluated in pin-and disk friction tests. The coatings and interface regions are examined by X-ray photoelectron spectroscopy. Results suggest that sputtered refractory compound coatings adhere best when a mixed compound of coating and substrate metals is formed in the interfacial region. The most effective type of refractory compound interface appears to depend on both substrate and coating material. A combination of metallic interlayer deposition and mixed compound interface formation may be more effective for some substrate coating combinations than either alone.

Brainard, W. A.↗
NASA NTRS1978

Prebiotic condensation reactions using cyanamide

Condensation reactions in cyanamide, 4-amino-5-imidazole-carboxamide and cyanamide, imidazole systems under dehydrating conditions at moderate temperatures (60 to 100 deg C) were investigated. The cyanamide, imidazole system was used for synthesis of palmitoylglycerols from ammonium palmitate and glycerol. With the addition of deoxythymidine to the former system, P1, P2-dideoxythymidine 5 prime-phosphate was obtained; the same cyanamide, 4-amino-5-imidazole-carboxamide system was used to synthesize deoxythymidine oligonucleotides using deoxythymidine 5 prime-phosphate and deoxythymidine 5 prime-triphosphate, and peptides using glycine, phenylalanine or isoleucine with adenosine 5 prime-triphosphate. The pH requirements for these reactions make their prebiotic significance questionable; however, it is conceivable that they could occur in stable pockets of low interlayer acidity in a clay such as montmorillonite.

Sherwood, E.↗
NASA NTRS1980

High temperature self-lubricating coatings for air lubricated foil bearings for the automotive gas turbine engine

coating combinations were developed for compliant surface bearings and journals to be used in an automotive gas turbine engine. The coatings were able to withstand the sliding start/stops during rotor liftoff and touchdown and occasional short time, high speed rubs under representative loading of the engine. Some dozen coating variations of CdO-graphite, Cr2O3 (by sputtering) and CaF2 (plasma sprayed) were identified. The coatings were optimized and they were examined for stoichiometry, metallurgical condition, and adhesion. Sputtered Cr2O3 was most adherent when optimum parameters were used and it was applied on an annealed (soft) substrate. Metallic binders and interlayers were used to improve the ductility and the adherence.

Bhushan, B.↗
NASA NTRS1979

Elevated temperature flow strength, creep resistance and diffusion welding characteristics of Ti-6Al-2Nb-1Ta-0.8Mo

A study of the flow strength, creep resistance and diffusion welding characteristics of the titanium alloy Ti-6Al-2Nb-1Ta-0.8Mo has been conducted. Two mill-processed forms of this alloy were examined. The forged material had been processed above the beta transus (approximately 1275 K) while the rolled form had been subjected to work below the beta transus. Between 1150 and 1250 K, the forged material was stronger and more creep resistant than the rolled alloy. Both forms exhibit superplastic characteristics in this temperature range. Strain measurements during diffusion welding experiments at 1200 K reveal that weld interfaces have no measurable effect on the overall creep deformation. Significant deformation appears to be necessary to produce a quality diffusion weld between superplastic materials. A 'soft' interlayer inserted between faying surfaces would seemingly allow manufacture of quality diffusion welds with little overall deformation.

Whittenberger, J. D.↗
NASA NTRS1980

Improved adhesion of sputtered refractory carbides to metal substrates

Sputtered coatings of the refractory metal carbides are of great interest for applications where hard wear-resistant materials are desired. The usefulness of sputtered refractory carbides is often limited in practice by spalling or interfacial separation. In this work improvements in the adherence of refractory carbides on iron, nickel and titanium base alloys were obtained by using oxidation, reactive sputtering or sputtered interlayers to alter the coating-substrate interfacial region. X-ray photoelectron spectroscopy and argon ion etching were used to characterize the interfacial regions, and an attempt was made to correlate adherence as measured in wear tests with the chemical nature of the interface.

Wheeler, D. R.↗
NASA NTRS1980

High efficiency epitaxial GaAs/GaAs and GaAs/Ge solar cell technology using OM/CVD

A technology for fabricating high efficiency, thin film GaAs solar cells on substrates appropriate for space and/or terrestrial applications was developed. The approach adopted utilizes organometallic chemical vapor deposition (OM-CVD) to form a GaAs layer epitaxially on a suitably prepared Ge epi-interlayer deposited on a substrate, especially a light weight silicon substrate which can lead to a 300 watt per kilogram array technology for space. The proposed cell structure is described. The GaAs epilayer growth on single crystal GaAs and Ge wafer substrates were investigated.

Wang, K. L.↗
NASA NTRS1981

Weld geometry strength effect in 2219-T87 aluminum

A theory of the effect of geometry on the mechanical properties of a butt weld joint is worked out based upon the soft interlayer weld model. Tensile tests of 45 TIG butt welds and 6 EB beads-on-plate in 1/4-in. 2219-T87 aluminum plate made under a wide range of heat sink and power input conditions are analyzed using this theory. The analysis indicates that purely geometrical effects dominate in determining variations in weld joint strength with heat sink and power input. Variations in weld dimensions with cooling rate are significant as well as with power input. Weld size is suggested as a better indicator of the condition of a weld joint than energy input.

Nunes, A. C., Jr.↗
NASA NTRS1981

High-efficiency thin-film GaAs solar cells, phase2

Thin GaAs epi-layers with good crystallographic quality were grown using a (100) Si-substrate on which a thin Ge epi-interlayer was grown by CVD from germane. Both antireflection-coated metal oxide semiconductor (AMOS) and n(+)/p homojunction structures were studied. The AMOS cells were fabricated on undoped-GaAs epi-layers deposited on bulk poly-Ge substrates using organo-metallic CVD film-growth, with the best achieved AM1 conversion efficiency being 9.1%. Both p-type and n(+)-type GaAs growth were optimized using 50 ppm dimethyl zinc and 1% hydrogen sulfide, respectively. A direct GaAs deposition method in fabricating ultra-thin top layer, epitaxial n(+)/p shallow homojunction solar cells on (100) GaAs substrates (without anodic thinning) was developed to produce large area (1 sq/cm) cells, with 19.4% AM1 conversion efficiency achieved. Additionally, an AM1 conversion efficiency of 18.4% (17.5% with 5% grid coverage) was achieved for a single crystal GaAs n(+)/p cell grown by OM-CVD on a Ge wafer.

Yeh, Y. C. M.↗
NASA NTRS1980

Composite wall concept for high-temperature turbine shrouds - Heat transfer analysis

The variables affecting the design of a composite turbine shroud, consisting of a metal base, an interlayer of porous metal, and an outer layer of yttria-stabilized zirconia, are analyzed. Results show that significant reductions in the cooling-air to gas-flow ratio are indicated for the composite shrouds compared to an all-metal shroud that was only impingement air cooled. The good insulating properties of the ceramic reduced the temperatures of the porous metal and support wall significantly. For a given porous metal density and coolant- to gas-flow ratio, decreasing the thickness of the porous metal and increasing ceramic thickness resulted in lower support wall temperatures. To maintain given allowable inter-layer temperatures and coolantto gas-flow ratios, porous-metal density or thermal conductivity must increase as the ratio of the thickness of the ceramic-to-porous metal decreases. It is concluded that a 1.78 mm thickness of porous material with a density of 0.2 and a 1.78 mm thickness of ceramic appears to be a good composite wall configuration for the assumed conditions

Ludwig, L. P.↗
NASA NTRS1981

Laminated anisotropic reinforced plastic plates and shells

Basic technical theories and engineering calculation equations for anisotropic plates and shells made of rigid reinforced plastics, mainly laminated fiberglass, are presented and discussed. Solutions are given for many problems of design of structural plates and shells, including curved sections and tanks, as well as two chapters on selection of the optimum materials, are given. Accounting for interlayer shearing and transverse separation, which are new engineering properties, are discussed. Application of the results obtained to thin three ply plates and shells wth a light elastic filler is presented and discussed.

Korolev, V. I.↗
NASA NTRS1981

High efficiency thin-film GaAs solar cells

The paper demonstrates the feasibility of producing high-efficiency GaAs solar cells with high power-to-weight ratios by organic metallic chemical vapor deposition (OM-CVD) growth of thin epi-layers on suitable substrates. An AM1 conversion efficiency of 18% (14% AM0), or 17% (13% AM0) with a 5% grid coverage is achieved for a single-crystal GaAs n(+)/p cell grown by OM-CVD on a Ge wafer. Thin GaAs epi-layers OM-CVD grown can be fabricated with good crystallographic quality using a Si-substrate on which a thin Ge epi-interlayer is first deposited by CVD from GeH4 and processed for improved surface morphology

Zwerdling, S.↗
NASA NTRS1980

Impact-induced water loss from serpentine, nontronite and kernite

Preliminary experiments have been conducted to study shock-release of volatiles from minerals. Impact-induced loss of bound water from hydrous minerals has been observed, using infrared absorption and X-ray powder diffractometer techniques. Serpentine (Mg3Si2O5(OH)4) and nontronite (.5Ca(0.7)Fe4/(Si(7.3)Al(0.7))O20/(OH)4.nH2O) were shocked and recovered from pressures of up to 38 GPa, using one-dimensional shock reverberation techniques. Kernite (Na2B4O7.4H2O) was impacted by a spherical pyrex projectile traveling at 4.89 km/sec, which produced a peak pressure of approximately 33 GPa. The infrared absorption spectra indicate that some of the bound water from these three minerals was released as a result of shock compression and subsequent rarefaction. This evidence is supported by the recovery of small amounts of vapor from the serpentine shocked to 23.5 GPa and the nontronite shocked to 18 GPa. The recovered vapor is inferred to be water from the shocked minerals. X-ray diffraction spectra indicate no major changes in the unit cell dimensions of the two silicates, except for a decrease in the lattice constant in the c-direction of the nontronite, consistent with the loss of interlayer water.

Boslough, M. B.↗
NASA NTRS1981

Energy efficient engine high-pressure turbine single crystal vane and blade fabrication technology report

The objective of the High-Pressure Turbine Fabrication Program was to demonstrate the application and feasibility of Pratt & Whitney Aircraft-developed two-piece, single crystal casting and bonding technology on the turbine blade and vane configurations required for the high-pressure turbine in the Energy Efficient Engine. During the first phase of the program, casting feasibility was demonstrated. Several blade and vane halves were made for the bonding trials, plus solid blades and vanes were successfully cast for materials evaluation tests. Specimens exhibited the required microstructure and chemical composition. Bonding feasibility was demonstrated in the second phase of the effort. Bonding yields of 75 percent for the vane and 30 percent for the blade were achieved, and methods for improving these yield percentages were identified. A bond process was established for PWA 1480 single crystal material which incorporated a transient liquid phase interlayer. Bond properties were substantiated and sensitivities determined. Tooling die materials were identified, and an advanced differential thermal expansion tooling concept was incorporated into the bond process.

Giamei, A. F.↗
NASA NTRS1982

High density circuit technology, part 2

A multilevel metal interconnection system for very large scale integration (VLSI) systems utilizing polyimides as the interlayer dielectric material is described. A complete characterization of polyimide materials is given as well as experimental methods accomplished using a double level metal test pattern. A low temperature, double exposure polyimide patterning procedure is also presented.

Wade, T. E.↗
NASA NTRS1984

Transmission electron microscopy of the 'LOW-CA' hydrated interplanetary dust particle

Transmission electron microscopy of a hydrated interplanetary dust particle indicates that it consists largely of a poorly crystalline phyllosilicate containing Fe, Mg and Al with an interlayer spacing of 10 to 12 A and so is distinct from the major phyllosilicate in CI and CM carbonaceous chondrites. The silicate is probably an Fe- and Mg-rich smectite or mica. Submicron, spherical to euhedral pyrrhotite and pentlandite are prominent. Unusual, low-Ni pentlandite is also common and typically occurs as rectangular platelets. Unlike many chondritic interplanetary dust particles, olivine is rare and pyroxene was not observed. Other less abundant phases are magnetite, chromite, and an unidentified phase containing Fe, Mg, Si, Ca, and Mn. This particle differs from a hydrated micrometeorite described previously by Brownlee (1978), indicating there are mineralogically different subsets of hydrated interplanetary dust particles. Despite gross similarities in mineralogy between the particle and the carbonaceous chondrites, they show appreciable differences in detail.

Tomeoka, K.↗
NASA NTRS1985

Zeolites on Mars: Prospects for Remote Sensing

The Martian surface composition measured by Viking can be represented by several combinations of minerals incorporating major fractions of zeolites known to occur in altered mafic rocks and polar soils on Earth. The abundant occurrence of zeolites on Mars is consistent with what is known about both the physical and chemical environment of that planet. The laboratory reflectance spectra (0.65 to 2.55 microns) of a number of relatively pure zeolite minerals and some naturally occurring zeolite-clay soils were measured. All of the spectra measured are dominated by strong absorption near 1.4 and 1.9 microns and a steep reflectance drop longward of about 2.2 microns, all of which are due to abundant H2O. Weaker water overtone bands are also apparent, and in most cases there is spectral evidence for minor Fe(3+). In these features the zeolite spectra are similar to spectra of smectite clays which have abundant interlayer water. The most diagnostic difference between clay and zeolite spectra is the total absence in the zeolites of the weak structural OH absorption.

E S Gaffney↗