Search NASA⌕ Search

SEARCH · Search NASA

Results for “light metals”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Developing the Next Generation Shell Buckling Design Factors and Technologies

NASA s Shell Buckling Knockdown Factor (SBKF) Project was established in the spring of 2007 by the NASA Engineering and Safety Center (NESC) in collaboration with the Constellation Program and Exploration Systems Mission Directorate. The SBKF project has the current goal of developing less-conservative, robust shell buckling design factors (a.k.a. knockdown factors) and design and analysis technologies for light-weight stiffened metallic launch vehicle (LV) structures. Preliminary design studies indicate that implementation of these new knockdown factors can enable significant reductions in mass and mass-growth in these vehicles and can help mitigate some of NASA s LV development and performance risks. In particular, it is expected that the results from this project will help reduce the reliance on testing, provide high-fidelity estimates of structural performance, reliability, robustness, and enable increased payload capability. The SBKF project objectives and approach used to develop and validate new design technologies are presented, and provide a glimpse into the future of design of the next generation of buckling-critical launch vehicle structures.

Hilburger, Mark W.↗
NASA NTRSDate not supplied

Process Recipes for Additively Printed Copper Ink Flexible Circuits using Direct Write Methods

In this paper, the process-recipes and process-performance relationships for additive-printing of copper circuits using direct-write methods have been studied. The process has been implemented on the direct write platform. Interest in the use of additive printing methods for the manufacture of micro-circuits has grown immensely in recent times. Direct write methods have been shown to have the ability to create circuits in a limited manner. However, the process recipes and the effect of process parameters on the manufactured properties are not well understood. Copper ink is a good and cost-effective alternative to silver ink but its use has lagged owing to an increased propensity for oxidation. In this paper, photonic curing has been used to sinter copper ink to make the traces conductive. The method flashes high energy light that sinter metal particles instantaneously and the temperature of the substrate remains low. The effect of the different photonic sintering profiles on the mechanical and electrical properties of the printed traces has been studied in this paper.The print process parameters also play an important role in the line width and height that has been studied to print with the desired line profile for the end application. An LC filter circuit is been printed with SMD components been attached using an electrically conductive adhesive (ECA). The manufactured flexible LC filter is been tested for its frequency sweep to compare with the commercially available LC filer with the help of the Bode plot.

Process control↗
NASA NTRSDate not supplied

Additive Manufacturing at NASA

Additive Manufacturing (AM) is certainly changing the space industry and providing new opportunities to travel to low earth orbit and explore our universe. New design opportunities –not previously possible –for new high performance metal alloys, light-weighting, managing thermal, structural, and dynamic loads are being enabled by AM. This presentation will showcase the vast portfolio of NASA’s AM activities in the last 12 years; transportation from Earth to Destination, Habitat at Destination, Lander from Station to Surface, and Science mission spacecrafts. NASA’s technical excellence is being leveraged heavily in the AM community thru collaborative projects, partnership agreements, tech transfer program. Challenges as well as opportunities will be discussed.

Alison Park↗
NASA NTRSDate not supplied

Technology Drives Exploration: How NASA Is Embracing Additive Manufacturing

NASA has over 60 years of technology development that enabled human space and space science exploration “for the benefit of all humankind”. This presentation will start with the overview of NASA’s organization structure; the roles NASA’s leadership plays as well as 10 regional centers’ focused areas and capabilities. It will also highlight NASA’s Mission Directorates –Science, Human, Aeronautics, and Technology. With the onset of the newer and still evolving procurement business model (NASA being a buyer, instead of maker), a question remains: which is the right framework under which NASA can best integrate the capabilities of commercial, international, and other US government entities into a coherent exploration strategy? Another critical consideration is identifying which critical technologies to invest in NASA and which capabilities are better suited for commercialization as NASA as a buyer. Additive Manufacturing (AM) is certainly changing the space industry and providing new opportunities to travel to low earth orbit and explore our universe. New design opportunities –not previously possible –for new high performance metal alloys, light-weighting, managing thermal, structural, and dynamic loads are being enabled by AM. This presentation will showcase the vast portfolio of NASA’s AM activities in the last 13 years; transportation from Earth to Destination, Habitat at Destination, Lander from Station to Surface, and Science mission spacecrafts. NASA’s technical excellence is being leveraged heavily in the AM and Commercial Space community through collaborative projects, partnership agreements, tech transfer program. Examples of challenges of AM implementation as well as opportunities will be discussed.

Alison Park↗
NASA NTRSDate not supplied

Additive Manufactured Hardware Qualification and Certification at NASA

Additive Manufacturing (AM) is certainly changing the space industry and providing new opportunities to travel to low earth orbit and explore our universe New design opportunities –not previously possible –for new high performance metal alloys, light-weighting, managing thermal, structural, and dynamic loads are being enabled by AM. Additively manufactured parts are already being inserted for complext system for NASA programs in critical applications –“ready to fly” Human exploration of space, especially deep space, requires extreme reliability Qualification of AM design/parts/process and Flight Certification

Alison Park↗
NASA NTRS1997

Anatomical features of pepper plants (Capsicum annuum L.) grown under red light-emitting diodes supplemented with blue or far-red light

Pepper plants (Capsicum annuum L. cv., Hungarian Wax) were grown under metal halide (MH) lamps or light-emitting diode (LED) arrays with different spectra to determine the effects of light quality on plant anatomy of leaves and stems. One LED (660) array supplied 90% red light at 660 nm (25nm band-width at half-peak height) and 1% far-red light between 700-800nm. A second LED (660/735) array supplied 83% red light at 660nm and 17% far-red light at 735nm (25nm band-width at half-peak height). A third LED (660/blue) array supplied 98% red light at 660nm, 1% blue light between 350-550nm, and 1% far-red light between 700-800nm. Control plants were grown under broad spectrum metal halide lamps. Plants were gron at a mean photon flux (300-800nm) of 330 micromol m-2 s-1 under a 12 h day-night photoperiod. Significant anatomical changes in stem and leaf morphologies were observed in plants grown under the LED arrays compared to plants grown under the broad-spectrum MH lamp. Cross-sectional areas of pepper stems, thickness of secondary xylem, numbers of intraxylary phloem bundles in the periphery of stem pith tissues, leaf thickness, numbers of choloplasts per palisade mesophyll cell, and thickness of palisade and spongy mesophyll tissues were greatest in peppers grown under MH lamps, intermediate in plants grown under the 660/blue LED array, and lowest in peppers grown under the 660 or 660/735 LED arrays. Most anatomical features of pepper stems and leaves were similar among plants grown under 660 or 660/735 LED arrays. The effects of spectral quality on anatomical changes in stem and leaf tissues of peppers generally correlate to the amount of blue light present in the primary light source.

NASA Discipline Life Support Systems↗
NASA NTRS2005

Instrumentation and Measurements for Electron Emission from Charged Insulators

The electron was first discovered in 1898 by Sir John Joseph Thomson and has since been the subject of detailed study by nearly every scientific discipline. At nearly the same time Heinrich Rudolf Hertz conducted a series of experiments using cathode tubes, high potentials and ultraviolet light. When applying a large potential to a cathode he found that an arching event across the metal plates would occur. In addition, when shining an ultraviolet light on the metal he found that less potential was required to induce the spark. This result, taken together with other electrical phenomena brought about by the shining of light upon metal and was eventually termed the photoelectric effect. The work of Thomson and Hertz represent the beginning of electron emission studies and a body of ideas that pervade nearly all aspects of physics. In particular these ideas tell us a great deal about the nature of physical interactions within solids. In this thesis we will focus on the emission of electrons induced by an incident electron source over a range of energies, in which one can observe changes in emitted electron flux and energy distribution. In particular, when energetic particles impinge on a solid they can impart their energy, exciting electrons within the material. If this energy is sufficient to overcome surface energy barriers such as the work function, electron affinity or surface charge potential, electrons can escape from the material. The extent of electron emission from the material can be quantified as the ratio of incident particle flux to emitted particle flux, and is termed the electron yield.

Sim, Alec M.↗
NASA NTRS1984

Electromagnetic modes of the asymmetric metal-oxide-metal tunnel junction

The characteristics of the modes of an Al-Al2O3-Ag tunnel junction are analyzed, and the way in which the field profiles, the propagation constant, and the attenuation depend on the thickness of the oxide layer is described. The significance of these results for investigations of light emission from metal-oxide-metal tunnel junctions is discussed.

Kurdi, B. N.↗
NASA NTRS2005

Optical Characterization of Metallic Aerosols

Airborne metallic particulates from industry and urban sources are highly conducting aerosols. The characterization of these pollutant particles is important for environment monitoring and protection. Because these metallic particulates are highly reflective, their effect on local weather or regional radiation budget may also need to be studied. In this work, light scattering characteristics of these metallic aerosols are studied using exact solutions on perfectly conducting spherical and cylindrical particles. It is found that for perfectly conducting spheres and cylinders, when scattering angle is larger than approx. 90 deg. the linear polarization degree of the scattered light is very close to zero. This light scattering characteristics of perfectly conducting particles is significantly different from that of other aerosols. When these perfectly conducting particles are immersed in an absorbing medium, this light scattering characteristics does not show significant change. Therefore, measuring the linear polarization of scattered lights at backward scattering angles can detect and distinguish metallic particulates from other aerosols. This result provides a great potential of metallic aerosol detection and monitoring for environmental protection.

Sun, Wenbo↗
NASA NTRS2006

Metal Foam Shields

This paper compares the ballistic performance of metallic foam sandwich structures with honeycomb structures. Honeycomb sandwich structures, consisting of metallic or composite facesheets and honeycomb cores, are often used in spacecraft construction due to their light-weight and structural stiffness. Honeycomb panels, however, are considered rather poor candidates for protection from micrometeoroid orbital debris (MMOD) particles because the honeycomb channels the debris cloud from MMOD impacts on outer facesheet causing a concentrated load on the second facesheet. Sandwich structures with light-weight, open-cell metallic cores and metal or composite facesheets provide improved MMOD protection because channeling does not occur and because the core is more effective at disrupting hypervelocity impacts then honeycomb. This paper describes hypervelocity impact tests on metallic foam sandwich structures (aluminum and titanium) with metallic facesheets, compare them to equivalent mass and thickness honeycomb panels, based on the results of hypervelocity impact tests.

Christiansen, Eric L.↗
NASA NTRS1985

Grazing incidence reflection coefficients of rhodium, osmium, platinum, and gold from 50 to 300 A

Reflectance measurements were made of several metals illuminated from various angles with light at 14 wavelengths in the interval 46.5-283 A. The metals, Rh, Os, Pt and Au were deposited as 125 A films on a binding substrate through electron beam epitaxy. Measurements were made with a grazing incidence monochromator and a reflectometer. The data generally showed lowered reflectance with increasing angles of illumination and shorter wavelengths. The reflectance peak, however, was located at wavelengths of 100-160 A, particularly at large grazing incidences. The wavelengths correspond with the 5p to epsilon-d transition in all of the elements. Rh displayed the highest overall reflectance, and both Rh and Os were more efficient than Au or Pt.

Hettrick, M. C.↗
NASA NTRS1980

Detecting contaminants by ultraviolet photography

Relatively high ultraviolet absorptivity of most organics as compared to metal is suggested as basis for detecting traces of contamination. By photographing metal surface in ultraviolet light, contaminants that might otherwise interfere with adhesion of surface coatings, or with welding or brazing, could be detected and removed. Real time monitoring of cleaning process is also possible if ultraviolet sensitive television camera is used instead of photographic film.

Neiswander, D. W.↗