Results for “matched load” — Page 5

NASA NTRS2005

Loads Model Development and Analysis for the F/A-18 Active Aeroelastic Wing Airplane

The Active Aeroelastic Wing airplane was successfully flight-tested in March 2005. During phase 1 of the two-phase program, an onboard excitation system provided independent control surface movements that were used to develop a loads model for the wing structure and wing control surfaces. The resulting loads model, which was used to develop the control laws for phase 2, is described. The loads model was developed from flight data through the use of a multiple linear regression technique. The loads model input consisted of aircraft states and control surface positions, in addition to nonlinear inputs that were calculated from flight-measured parameters. The loads model output for each wing consisted of wing-root bending moment and torque, wing-fold bending moment and torque, inboard and outboard leading-edge flap hinge moment, trailing-edge flap hinge moment, and aileron hinge moment. The development of the Active Aeroelastic Wing loads model is described, and the ability of the model to predict loads during phase 2 research maneuvers is demonstrated. Results show a good match to phase 2 flight data for all loads except inboard and outboard leading-edge flap hinge moments at certain flight conditions. The average load prediction errors for all loads at all flight conditions are 9.1 percent for maximum stick-deflection rolls, 4.4 percent for 5-g windup turns, and 7.7 percent for 4-g rolling pullouts.

Allen, Michael J.↗

NASA NTRS2005

Loads Model Development and Analysis for the F/A-18 Active Aeroelastic Wing Airplane

The Active Aeroelastic Wing airplane was successfully flight-tested in March 2005. During phase 1 of the two-phase program, an onboard excitation system provided independent control surface movements that were used to develop a loads model for the wing structure and wing control surfaces. The resulting loads model, which was used to develop the control laws for phase 2, is described. The loads model was developed from flight data through the use of a multiple linear regression technique. The loads model input consisted of aircraft states and control surface positions, in addition to nonlinear inputs that were calculated from flight-measured parameters. The loads model output for each wing consisted of wing-root bending moment and torque, wing-fold bending moment and torque, inboard and outboard leading-edge flap hinge moment, trailing-edge flap hinge moment, and aileron hinge moment. The development of the Active Aeroelastic Wing loads model is described, and the ability of the model to predict loads during phase 2 research maneuvers is demonstrated. Results show a good match to phase 2 flight data for all loads except inboard and outboard leading-edge flap hinge moments at certain flight conditions. The average load prediction errors for all loads at all flight conditions are 9.1 percent for maximum stick-deflection rolls, 4.4 percent for 5-g windup turns, and 7.7 percent for 4-g rolling pullouts.

Allen, Michael J.↗

NASA NTRS1963

STATIC POWER CONVERSION FOR SPACECRAFT

Static power conversion systems for medium power level needs of spacecraft, and problems of matching power sources to the load

SPACECRAFT POWER SUPPLY↗

NASA NTRS1985

Maximum Outputs of Solar Photovoltaic Arrays

Report presents electrical data for solar photovoltaic arrays operating at different locations in United States. Data useful in designing power-conditioners for matching output of array to load.

Ross, R. G., Jr.↗

NASA NTRS1991

High-power generation in IMPATT devices in the 100-200-GHz range

A silicon double-drift IMPATT diode with high uniform doping levels was simulated. Simulation results show that it is possible for silicon IMPATT diodes to generate extremely high pulsed output power for frequencies above 100 GHz under high current-density operation. The highest output power matched to a 1-ohm load resistance obtained at 150 GHz is 37.7 W, with a dc current density of 200 kA/sq cm, although the calculated power conversion efficiency is low. It is also shown that the low-power conversion efficiency limits the diode's continuous wave power operation.

Chen, Chien-Chung↗

NASA NTRS2005

Failure Analysis of Discrete Damaged Tailored Extension-Shear-Coupled Stiffened Composite Panels

The results of an analytical and experimental investigation of the failure of composite is tiffener panels with extension-shear coupling are presented. This tailored concept, when used in the cover skins of a tiltrotor aircraft wing has the potential for increasing the aeroelastic stability margins and improving the aircraft productivity. The extension-shear coupling is achieved by using unbalanced 45 plies in the skin. The failure analysis of two tailored panel configurations that have the center stringer and adjacent skin severed is presented. Finite element analysis of the damaged panels was conducted using STAGS (STructural Analysis of General Shells) general purpose finite element program that includes a progressive failure capability for laminated composite structures that is based on point-stress analysis, traditional failure criteria, and ply discounting for material degradation. The progressive failure predicted the path of the failure and maximum load capability. There is less than 12 percent difference between the predicted failure load and experimental failure load. There is a good match of the panel stiffness and strength between the progressive failure analysis and the experimental results. The results indicate that the tailored concept would be feasible to use in the wing skin of a tiltrotor aircraft.

Baker, Donald J.↗

NASA NTRS2020

A Scaling Methodology Applied to Buckling of Sandwich Composite Cylindrical Shells

Studying buckling behavior of large shell structures through full-scale test articles can be complex and expensive. Therefore, reduced scale structures are often preferred to investigate the buckling behavior. However, designing reduced scale structures that are representative of the full-scale structure can be difficult. An analytical scaling methodology for compression-loaded sandwich composite cylindrical shells based on the nondimensionalization of the buckling equations is presented herein. The methodology is used to develop scaled configurations that show similar buckling responses to the full-scale baseline configuration. Finite element analysis results showed that both a baseline and a scaled configuration buckled similarly, when the nondimensional stiffness, defined as the ratio between the nondimensional load and nondimensional displacement, is matched between the different scale models. Limitations of the methodology are discussed and are believed to be a result of neglecting the flexural anisotropy and the transverse shear compliance. A preliminary failure assessment for the different scales is also considered.

Ines Uriol Balbin↗

NASA NTRS2007

Frequency Response of an Aircraft Wing with Discrete Source Damage Using Equivalent Plate Analysis

An equivalent plate procedure is developed to provide a computationally efficient means of matching the stiffness and frequencies of flight vehicle wing structures for prescribed loading conditions. Several new approaches are proposed and studied to match the stiffness and first five natural frequencies of the two reference models with and without damage. One approach divides the candidate reference plate into multiple zones in which stiffness and mass can be varied using a variety of materials including aluminum, graphite-epoxy, and foam-core graphite-epoxy sandwiches. Another approach places point masses along the edge of the stiffness-matched plate to tune the natural frequencies. Both approaches are successful at matching the stiffness and natural frequencies of the reference plates and provide useful insight into determination of crucial features in equivalent plate models of aircraft wing structures.

Krishnamurthy, T.↗

NASA NTRSDate not supplied

Effects of Trailing Edge Thickness and Blade Loading Distribution on the Aerodynamic Performance of Simulated CMC Turbine Blades

The aerodynamic performance of three blade sets that represent the geometric manufacturing constraints of Ceramic Matrix Composite (CMC) blades was measured experimentally in a large-scale transonic turbine blade cascade. The trailing edge thicknesses of CMC blades are anticipated to be significantly larger than those of current state-of-the-art metallic blades. The blades tested in the current study had trailing edge thicknesses of 5%, 7%, and 9% relative to the blade axial chord. The three blade sets were designed with matching throat dimensions, so the blade loading distributions were varied to retain similar overall loading levels. Data were acquired at four Reynolds numbers, covering a factor of six range. All data were acquired at the design isentropic exit Mach number of 0.74. Measurements include blade loading and five-hole probe surveys at two downstream stations. The effects of inlet turbulence intensity were also quantified. Total pressure loss data were integrated to determine overall loss levels for each of the three measured blade passages. Excellent periodicity was noted. For low inlet turbulence levels, losses were surprisingly lower for the thickest trailing edge at low Reynolds numbers, but were highest at the maximum Reynolds number. In general, losses were found to scale well with Reynolds number, although front loading was found to significantly reduce the sensitivity of loss to Reynolds number. For high inlet turbulence intensity, losses were found to scale with trailing edge thickness as expected, and the Reynolds number sensitivity was reduced for all three blade sets. Loss levels at the highest Reynolds number were comparable at low and high inlet turbulence intensity levels.

Paul W Giel↗

NASA NTRSDate not supplied

Effects of Trailing Edge Thickness and Blade Loading Distribution on the Aerodynamic Performance of Simulated CMC Turbine Blades

The aerodynamic performance of three blade sets that represent the geometric manufacturing constraints of Ceramic Matrix Composite (CMC) blades was measured experimentally in a large-scale transonic turbine blade cascade. The trailing edge thicknesses of CMC blades are anticipated to be significantly larger than those of current state-of-the-art metallic blades. The blades tested in the current study had trailing edge thicknesses of 5%, 7%, and 9% relative to the blade axial chord. The three blade sets were designed with matching throat dimensions, so the blade loading distributions were varied to retain similar overall loading levels. Data were acquired at four Reynolds numbers, covering a factor of six range. All data were acquired at the design isentropic exit Mach number of 0.74. Measurements include blade loading and five-hole probe surveys at two downstream stations. The effects of inlet turbulence intensity were also quantified. Total pressure loss data were integrated to determine overall loss levels for each of the three measured blade passages. Excellent periodicity was noted. For low inlet turbulence levels, losses were surprisingly lower for the thickest trailing edge at low Reynolds numbers, but were highest at the maximum Reynolds number. In general, losses were found to scale well with Reynolds number, although front loading was found to significantly reduce the sensitivity of loss to Reynolds number. For high inlet turbulence intensity, losses were found to scale with trailing edge thickness as expected, and the Reynolds number sensitivity was reduced for all three blade sets. Loss levels at the highest Reynolds number were comparable at low and high inlet turbulence intensity levels.

Turbine↗

NASA NTRSDate not supplied

Testing of ACC-6 Carbon-Carbon at High Strain Rates and High Temperatures

Some materials, such as steel, titanium, and tungsten, have a yield stress that depends on the strain rate, and actually are stronger at high rates of load or deformation. The increase in strength is relevant; and if not taken into account, the computer models will not match the experimental behavior observed in typical shock loading, ordnance, or ballistic tests. For higher velocity (hypervelocity impacts), an equation of state that accounts for non-linearities and temperature in the pressure-volume relation, may also be needed. This rate-dependent behavior of the strength has also been observed in some composite materials. Southwest Research Institute® (SwRI®) has started an internal research effort to measure and better model the behavior of materials, in particular carbon/carbon composites like ACC-6, at ultra-high temperatures for both static and high rates of deformation. The ultimate objective is to obtain reliable computer models of carbon/carbon material under hypersonic flight conditions, hypervelocity impacts, shock-loading situations such as booster-vehicle separation, and munition operation events. SwRI® has successfully modeled in the past ballistic impact on other composites, namely S-2 glass/epoxy, Kevlar/resin, polyethylene fibers/resin, and carbon fiber composites. This presentation will show test results relevant to the strength properties of the ACC-6 C/C material which were measured at quasistatic, medium, and the moderately high strain rates (~103 s—1) achievable in a conventional Split Hopkinson bar apparatus. Some of the tests were performed at both high-rates and high temperatures typical of hypersonic flight, something that, to the authors’ knowledge, has never been published in the past for this particular material. The test method will be presented, as well as the comparison of the stress-strain curves for the different temperatures and strain-rates of interest. A discussion of how the results can be used in the typical hydrocodes of interest will be included.

carbon/carbon↗

NASA NTRS1999

Lightweight Battery Charge Regulator Used to Track Solar Array Peak Power

A battery charge regulator based on the series-connected boost regulator (SCBR) technology has been developed for high-voltage spacecraft applications. The SCBR regulates the solar array power during insolation to prevent battery overcharge or undercharge conditions. It can also be used to provide regulated battery output voltage to spacecraft loads if necessary. This technology uses industry-standard dc-dc converters and a unique interconnection to provide size, weight, efficiency, fault tolerance, and modularity benefits over existing systems. The high-voltage SCBR shown in the photograph has demonstrated power densities of over 1000 watts per kilogram (W/kg). Using four 150-W dc-dc converter modules, it can process 2500 W of power at 120 Vdc with a minimum input voltage of 90 Vdc. Efficiency of the SCBR was 94 to 98 percent over the entire operational range. Internally, the unit is made of two separate SCBR s, each with its own analog control circuitry, to demonstrate the modularity of the technology. The analog controllers regulate the output current and incorporate the output voltage limit with active current sharing between the two units. They also include voltage and current telemetry, on/off control, and baseplate temperature sensors. For peak power tracking, the SCBR was connected to a LabView-based data acquisition system for telemetry and control. A digital control algorithm for tracking the peak power point of a solar array was developed using the principle of matching the source impedance with the load impedance for maximum energy transfer. The algorithm was successfully demonstrated in a simulated spacecraft electrical system at the Boeing PhantomWorks High Voltage Test Facility in Seattle, Washington. The system consists of a 42-string, high-voltage solar array simulator, a 77-cell, 80-ampere-hour (A-hr) nickel-hydrogen battery, and a constant power-load module. The SCBR and the LabView control algorithm successfully tracked the solar array peak power point through various load transients, including sunlight discharge transients when the total load exceeded the maximum solar array output power.

Soeder, James F.↗

NASA NTRS1973

Evaluation of a high response electrohydraulic digital control valve

The application is described of a digital control valve on an electrohydraulic servo actuator. The digital control problem is discussed in general as well as the design and evaluation of a breadboard actuator. The evaluation revealed a number of problems associated with matching the valve to a hydraulic load. The problems were related to lost motion resulting from bulk modulus and leakage. These problems were effectively minimized in the breadboard actuator by maintaining a 1000 psi back pressure on the valve circuit and thereby improving the effective bulk modulus.

Anderson, R. L.↗

NASA NTRS1975

Internal convective cooling systems for hypersonic aircraft

Parametric studies were conducted to investigate the relative merits of construction materials, coolants, and cooled panel concepts for internal convective cooling systems applied to airframe structures of hydrogen-fueled hypersonic aircraft. These parametric studies were then used as a means of comparing various cooled structural arrangements for a hypersonic transport and a hypersonic research airplane. The cooled airplane studies emphasized weight aspects as related to the choice of materials, structural arrangements, structural temperatures, and matching of the cooling system heat load to the available hydrogen fuel-flow heat sink. Consideration was given to reliability and to fatigue and fracture aspects, as well. Even when auxiliary thermal protection system items such as heat shielding, insulation, and excess hydrogen for cooling are considered the more attractive actively cooled airframe concepts indicated potential payload increases of from 40 percent to over 100 percent for the hypersonic transport as compared to the results of previous studies of the same vehicle configuration with an uncooled airframe.

Anthony, F. M.↗

NASA NTRS1976

Actively cooled airframe structures for high-speed flight

An assessment of forced convectively cooled aircraft structures is presented based on recent and on-going studies. Particular emphasis is given to contractual efforts in which large panels of three different concepts are being designed and fabricated for cyclic thermal-structural tests at the Langley Research Center. Results of ambient temperature fatigue tests of small specimens of these concepts are reviewed. Aspects of conceptual and detail designs, material selection, fabrication, reliability, and heat-load/hydrogen fuel heat-sink matching are discussed. Results to date indicate that active cooling significantly impacts the structural design process, and, despite the use of conventional aluminum materials, advanced complex fabrication processes are required.

Nowak, R. J.↗

NASA NTRS1983

Development of controlled diffusion airfoils for multistage compressor application

A series of Controlled Diffusion Airfoils has been developed for multistage compressor application. These airfoils are designed analytically to be shock free at transonic Mach number and to avoid suction surface boundary layer separation for a range of inlet conditions necessary for stable compressor operation. They have demonstrated, in cascade testing, higher critical Mach number, higher incidence range, and higher loading capability than standard series airfoils designed for equivalent aerodynamic requirements. These airfoils have been shown, in single and multistage rig testing, to provide high efficiency, high loading capability, and ease of stage matching, leading to reduced development costs and improved surge margin. The Controlled Diffusion Airfoil profile shapes tend to have thicker leading and trailing edges than their standard series counterparts, leading to improved compressor durability.

Hobbs, D. E.↗

NASA NTRS2002

Arc Jet Testing of the TIRS Cover Thermal Protection System for Mars Exploration Rover

This paper summarizes the arc jet test results of the Mars Exploration Rover (MER) Silicone Impregnated Reusable Ceramic Ablator (SIRCA) Transverse Impulse Rocket System (TIRS) Cover test series in the Panel Test Facility (PTF) at NASA Ames Research Center (ARC). NASA ARC performed aerothermal environment analyses, TPS sizing and thermal response analyses, and arc jet testing to evaluate the MER SIRCA TIRS Cover design and interface to the aeroshell structure. The primary objective of this arc jet test series was to evaluate specific design details of the SIRCA TIRS Cover interface to the MER aeroshell under simulated atmospheric entry heating conditions. Four test articles were tested in an arc jet environment with various sea] configurations. The test condition was designed to match the predicted peak flight heat load at the gap region between the SIRCA and the backshell TPS material, SLA-561S, and resulted in an over-test (with respect to heat flux and heat load) for the apex region of the SIRCA TIRS Cover. The resulting pressure differential was as much as twenty times that predicted for the flight case, depending on the location, and there was no post-test visual evidence of over-heating or damage to the seal, bracket, or backshell structure. The exposed titanium bolts were in good condition at post-test and showed only a small amount of oxidation at the leading edge locations. Repeatable thermocouple data were obtained and SIRCA thermal response analyses were compared to applicable thermocouple data. For the apex region of the SIRCA TIRS Cover, a one-dimensional thermal response prediction proved overly conservative, as there were strong multi-dimensional conduction effects evident from the thermocouple data. The one-dimensional thermal response prediction compared well with the thermocouple data for the leading edge "lip" region at the bolt location. In general, the test results yield confidence in the baseline seal design to prevent hot gas ingestion at the bracket and composite aeroshell structure interface.

Szalai, Christine E.↗

NASA NTRS1991

Lunar crane system

In many lunar construction scenarios, mechanical cranes in some form will be indispensible in moving large masses around with various degrees of fine positioning. While thorough experience exists in the use of terrestrial cranes new thinking is required about the design of cranes to be used in extraterrestrial construction. The primary driving force for this new thinking is the need to automate the crane system so that space cranes can be operated as telerobotic machines with a large number of automatic capabilities. This is true because in extraterrestrial construction human resources will need to be critically rationed. The design problems of mechanisms and control systems for a lunar crane must deal with at least two areas of performance. First, the automated crane must be capable of maneuvering a large mass, so that when the mass arrives at the target position there are only small vibrations. Secondly, any residue vibrations must be automatically damped out and a fine positioning must be achieved. For extraterrestrial use there are additional challenges to a crane design - for example, to design a crane system so that it can be transformed for other construction uses. This initial project in crane design does not address such additional issues, although they may be the subject of future CSC research. To date the Center has designed and analyzed many mechanisms. The fundamental problem of trade-offs between passively stabilizing the load and actively controlling the load by actuators was extensively studied. The capability of 3D dynamics modeling now exists for such studies. A scaled model of a lunar crane was set up and it has been most fruitful in providing basic understanding of lunar cranes. Due to an interesting scaling match-up, this scaled model exhibits the load vibration frequencies one would expect in the real lunar case. Using the analytical results achieved to date, a laboratory crane system is now being developed as a test bed for verifying a wide variety of mechanisms and control designs. Future development will be aimed at making the crane system a telerobotic test bed into which external sensors such as computer vision systems, and other small robotic devices such as CSC lunar rovers, will be integrated.

Mikulas, Martin M., Jr.↗