Search NASA⌕ Search

SEARCH · Search NASA

Results for “materials property”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Material properties and device evaluations of ECR-deposited a-Si:H and a-SiC:H films

Device-quality a-Si:H and a-SiC:H films have been deposited using electron cyclotron resonance (ECR) microwave plasmas of SiH4, CH4, and H2 mixtures. Typical material properties of ECR-deposited, photosensitive a-Si:H films are: (1) high photosensitivity up to 2 x 106 with a photoconductivity of 10 exp -5 to 10 exp -4/(Ohm-cm), (2) a Tauc gap of 1.75 to 1.85 eV, (3) an Urbach slope of 50-60 meV determined by the constant photocurrent method, and (4) an integrated defect density of 1-2 x 10 exp 16/cu cm determined by junction capacitance measurements. Highly conductive, p-type a-SiC:H films have been produced by ECR plasmas with a conductivity of 0.2/(Ohm-cm).

Shing, Y. H.↗
NASA NTRS1985

Effect of measured material properties on the finite element analysis of an OH-58 composite tail boom

A static and dynamic finite element analysis is conducted on a U.S. Army OH-58 composite tail boom and compared with test data. The tail boom is a filament-wound graphite/epoxy monocoque structure. The structural design of the composite tail boom skin is based on 50-percent graphite fiber volume. However, material tests on representative samples of the tail boom skin reveal that the graphite fiber-volume fraction varied from 44.6 to 49.3 percent. To determine the effect of using measured material properties, static and dynamic finite element analyses are conducted for three fiber-volume conditions of 45, 48, and 50 percent. The static and dynamic model with the 45-percent fiber-volume graphite skins gives the closest agreement with test data.

Bowman, L. M.↗
NASA NTRS2002

Decreases in bone blood flow and bone material properties in aging Fischer-344 rats

The purpose of this study was to quantify precisely aging-induced changes in skeletal perfusion and bone mechanical properties in a small rodent model. Blood flow was measured in conscious juvenile (2 months old), adult (6 months old), and aged (24 months old) male Fischer-344 rats using radiolabeled microspheres. There were no significant differences in bone perfusion rate or vascular resistance between juvenile and adult rats. However, blood flow was lower in aged versus adult rats in the forelimb bones, scapulas, and femurs. To test for functional effects of this decline in blood flow, bone mineral density and mechanical properties were measured in rats from these two age groups. Bone mineral density and cross-sectional moment of inertia in femoral and tibial shafts and the femoral neck were significantly larger in the aged versus adult rats, resulting in increased (+14%-53%) breaking strength and stiffness. However, intrinsic material properties at midshaft of the long bones were 12% to 25% lower in the aged rats. Although these data are consistent with a potential link between decreased perfusion and focal alterations in bone remodeling activity related to clinically relevant bone loss, additional studies are required to establish the mechanisms for this putative relationship.

Non-NASA Center↗
NASA NTRS2000

Correlation Between Material Properties of Ferroelectric Thin Films and Design Parameters for Microwave Device Applications: Modeling Examples and Experimental Verification

The application of thin ferroelectric films for frequency and phase agile components is the topic of interest of many research groups worldwide. Consequently, proof-of-concepts (POC) of different tunable microwave components using either (HTS, metal)/ferroelectric thin film/dielectric heterostructures or (thick, thin) film "flip-chip" technology have been reported. Either as ferroelectric thin film characterization tools or from the point of view of circuit implementation approach, both configurations have their respective advantages and limitations. However, we believe that because of the progress made so far using the heterostructure (i.e., multilayer) approach, and due to its intrinsic features such as planar configuration and monolithic integration, a study on the correlation of circuit geometry aspects and ferroelectric material properties could accelerate the insertion of this technology into working systems. In this paper, we will discuss our study performed on circuits based on microstrip lines at frequencies above 10 GHz, where the multilayer configuration offers greater ease of insertion due to circuit's size reduction. Modeled results of relevant circuit parameters such as the characteristic impedance, effective dielectric constant, and attenuation as a function of ferroelectric film's dielectric constant, tans, and thickness, will be presented for SrTiO3 and Ba(x)Sr(1-x)TiO3 ferroelectric films. A comparison between the modeled and experimental data for some of these parameters will be presented.

Miranda, Felix A.↗
NASA NTRS2010

Material Properties of Three Candidate Elastomers for Space Seals Applications

A next-generation docking system is being developed by the National Aeronautics and Space Administration (NASA) to support Constellation Space Exploration Missions to low Earth orbit (LEO), to the Moon, and to Mars. A number of investigations were carried out to quantify the properties of candidate elastomer materials for use in the main interface seal of the Low Impact Docking System (LIDS). This seal forms the gas pressure seal between two mating spacecraft. Three candidate silicone elastomer compounds were examined: Esterline ELA-SA-401, Parker Hannifin S0383-70, and Parker Hannifin S0899-50. All three materials were characterized as low-outgassing compounds, per ASTM E595, so as to minimize the contamination of optical and solar array systems. Important seal properties such as outgas levels, durometer, tensile strength, elongation to failure, glass transition temperature, permeability, compression set, Yeoh strain energy coefficients, coefficients of friction, coefficients of thermal expansion, thermal conductivity and diffusivity were measured and are reported herein.

Bastrzyk, Marta B.↗
NASA NTRS2012

Electromagnetic Nondestructive Evaluation of Wire Insulation and Models of Insulation Material Properties

Polymers have been widely used as wiring electrical insulation materials in space/air-craft. The dielectric properties of insulation polymers can change over time, however, due to various aging processes such as exposure to heat, humidity and mechanical stress. Therefore, the study of polymers used in electrical insulation of wiring is important to the aerospace industry due to potential loss of life and aircraft in the event of an electrical fire caused by breakdown of wiring insulation. Part of this research is focused on studying the mechanisms of various environmental aging process of the polymers used in electrical wiring insulation and the ways in which their dielectric properties change as the material is subject to the aging processes. The other part of the project is to determine the feasibility of a new capacitive nondestructive testing method to indicate degradation in the wiring insulation, by measuring its permittivity.

Bowler, Nicola↗
NASA NTRSDate not supplied

High Temperature Material Properties Measurement Capabilities of the MSFC Electrostatic Levitation (ESL) Laboratory

The NASA Marshall Space Flight Center (MSFC) electrostatic levitation (ESL) laboratory has a long history of providing materials research and thermophysical property data. The lab can measure thermophysical properties, such as density, surface tension, and viscosity of liquid materials, including elements, alloys, glasses, ceramics, and oxides. For improved measurement quality, the ESL lab also has an oxygen control system, which allows the oxygen partial pressure within the vacuum chamber to be measured and controlled, at elevated temperatures, over a wide range of partial pressures. The surface tension of metals is affected by even a small amount of adsorption of oxygen, and the presence of oxygen has been hypothesized as a likely cause for the large scatter seen in published surface tension data. This presentation will cover the MSFC ESL lab, its high temperature material properties measurement capabilities, and some information about measurements done on alloys relevant to additive manufacturing.

Michael SanSoucie↗
NASA NTRS1974

Estimation of material properties of a nonlinearly elastic bar

A method of determining certain characteristic flexural rigidities and elastic properties of nonlinearly elastic materials is presented. An estimation method utilizing perturbation methods and a least squares fitting technique is used to solve the nonlinear differential equation derived from the moment curvature relation, subject to boundary values representing deflections of the bar at discrete points. Deflection data from numerical simulations of a nonlinearly elastic, prismatic bar are used to demonstrate the estimation method. Numerical experiments relating the accuracy of the identification to the number and accuracy of the boundary values are presented. Conclusions based on the numerical experiments are included.

Baker, B. E.↗
NASA NTRS1985

Loss mechanisms in high-efficiency solar cells: Study of material properties and high-efficiency solar-cell performance on material composition: Project tasks

Loss mechanisms in high-efficiency solar cells were discussed. Fundamental limitations and practical solutions were stressed. Present cell efficiency is limited by many recombination sites: emitter, base, contacts, and oxide/silicon interface. Use of polysilicon passivation was suggested. After reduction of these losses, a 25% efficient cell could be built. A floating emitter cell design was shown that had the potential of low recombination losses.

Sah, C. T.↗
NASA NTRS1988

Symbolic derivation of material property matrices in finite element analysis

The principles and operation of MMAX, a symbolic-computation program which automates the process of generating property matrices for structural materials, are briefly described and illustrated with sample analyses of a rubberlike material and an elastoplastic material. MMAX is written in LISP under the symbolic finite-element generator FINGER and the general symbolic manipulator MACSYMA; it first derives the formulas required by mathematical manipulation, and then translates the formulas into FORTRAN code, adapted to the particular type of machine to be used for the numerical calculations. This approach is shown to combine efficiently the advantages of symbolic and numerical computation for engineering applications.

Tan, H. Q.↗
NASA NTRS1976

On the thermoelastic analysis of solar cell arrays and related material properties

Accurate prediction of failure of solar cell arrays requires accuracy in the computation of thermally induced stresses. This was accomplished by using the finite element technique. Improved procedures for stress calculation were introduced together with failure criteria capable of describing a wide range of ductile and brittle material behavior. The stress distribution and associated failure mechanisms in the N-interconnect junction of two solar cell designs were then studied. In such stress and failure analysis, it is essential to know the thermomechanical properties of the materials involved. Measurements were made of properties of materials suitable for the design of lightweight arrays: microsheet-0211 glass material for the solar cell filter, and Kapton-H, Kapton F, Teflon, Tedlar, and Mica Ply PG-402 for lightweight substrates. The temperature-dependence of the thermal coefficient of expansion for these materials was determined together with other properties such as the elastic moduli, Poisson's ratio, and the stress-strain behavior up to failure.

Salama, M. A.↗
NASA NTRS2023

PMT F7 Silver Standard Material Properties Characterization

PMT F7 epoxy resin was characterized to capture the material's thermochemical and thermo-mechanical properties. DSC testing was performed and the data was used to develop a cure kinetics model which predicts the material cure response and specific heat capacity. TMA and DMA testing were performed and the data was used to develop thermo-mechanical models which predict the material CTE, cure shrinkage, and modulus evolution with cure. Convergent Manufacturing Technologies US determined test parameters, analyzed data, and performed model fitting. NASA completed tests and provided data to Convergent Manufacturing Technologies US.

Epoxy↗
NASA NTRS1978

Measurements of material properties for solar cells

Measurements on two candidate materials for space flight are reported. The observed optical transmittance of aluminum films vapor deposited on fused quartz showed anomalously high transmittance thru 400 A and 600 A and showed an effective skin depth of 110 A in the latter part of the 1000 A thickness. KAPTON films are shown by their optical transmission spectra to have an energy gap for electron excitation of approximately 2.5 eV, which value depends on the thickness as manufactured. The resistance of KAPTON film to ionizing radiation is described by their optical spectra and their electron spin resonance spectra.

Castle, J. G., Jr.↗
NASA NTRS1981

Investigation of Test Methods, Material Properties, and Processes for Solar Cell Encapsulants

Encapsulant materials and processes for the production of cost effective, long life solar cell modules are identified, and evaluated. Ethylene vinyl acetate lamination pottant studies are conducted with respect to the time/temperature cure requirements for successful use of this compound. The time needed to produce successful gel contents are redetermined at a variety of temperatures and are related to the peroxide half life temperature curve. Formulation of the butyl acrylate syrup casting pottant is complete. The formulation contains an ultraviolet stabilizer system and is cured with an initiator that presents no shipping or handling hazards. The catalyzed syrup is stable at room temperature and has a pot life of at least an eight hour period of time. The syrup cures to a transparent rubber in 18 minutes at a temperature of 60 C.

Willis, P. B.↗
NASA NTRS1981

Investigation of test methods, material properties, and processes for solar cell encapsulants

Encapsulant materials and processes for the production of cost-effective, long-life solar cell modules were investigated. The following areas were explored: (1) soil resistant surface treatment; (2) corrosion protecting coatings from mild steel substrates; (3) primers for bonding module interfaces; and (4) RS/4 accelerated aging of candidate encapsulation compounds

Willis, P. B.↗
NASA NTRS1977

Investigation of test methods, material properties and processes for solar cell encapsulants

The potentially useful encapsulating materials for Task 3 of the Low-Cost Silicon Solar Array project were studied to identify, evaluate, and recommend encapsulant materials and processes for the production of cost-effective, long-life solar cell modules. Materials for study were chosen on the basis of existing knowledge of generic chemical types having high resistance to environmental weathering. The materials varied from rubbers to thermoplastics and presented a broad range of mechanical properties and processing requirements. Basic physical and optical properties were measured on the polymers and were redetermined after exposure to indoor artificial accelerated aging conditions covering four time periods. Strengths and weaknesses of the various materials were revealed and data was accumulated for the development of predictive methodologies. To date, silicone rubbers, fluorocarbons, and acrylic polymers appear to have the most promising combination of characteristics. The fluorocarbons may be used only as films, however, because of their high cost.

Willis, P. B.↗
NASA NTRS1983

Investigation of test methods, material properties and processes for solar cell encapsulants

Low cost encapsulation materials for the Flat Plate Solar Array Program (FSA) are investigated. The goal of the program is to identify, test, evaluate and recommend encapsulation materials and processes for the fabrication of cost effective and long life solar modules. Accelerated aging techniques for module component lifetime studies, investigation of candidate outer cover films and continued evaluation of soil repellant coatings are also included.

Willis, P. B.↗