Search NASA⌕ Search

SEARCH · Search NASA

Results for “mechanical crush”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Crushing behaviors of unidirectional carbon fiber reinforced plastic composites under dynamic bending and axial crushing loading

The dynamic crushing characteristics of unidirectional carbon fiber reinforced plastic composites under two loading types, dynamic three-point bending and axial crushing, are investigated by experiment and finite element simulation. Hat section samples with two different layup orientations are tested at various impact velocities to investigate its effects. The experiment results show that delamination plays a critical role in dynamic bending deformation. Different layup orientations lead to similar crushing bending behaviors, but remarkable variations in delamination pattern evolutions. In contrast, layup orientation exerts more significant effects on failure modes and energy absorption in axial crushing. A finite element model with multiple layers of thick shell element and cohesive element is established, and simulations are performed for both dynamic three-point bending and axial crushing. The model can capture the crushing behaviors in the two loading types reasonably well. The damage evolution and energy absorption through various mechanisms at different loading conditions are discussed.

42 ENGINEERING↗

Characterization of Microporous Insulation, Microsil

Microsil microporous insulation has been characterized by Lawrence Livermore National Laboratory for possible use in structural and thermal applications in the DPP-1 design. Qualitative test results have provided mechanical behavioral characteristics for DPP-1 design studies and focused on the material behavioral response to being crushed, cyclically loaded, and subjected to vibration for a confined material with an interference fit or a radial gap. Quantitative test results have provided data to support the DPP-1 FEA model analysis and verification and were used to determine mechanical property values for the material under a compression load. The test results are documented within this report.

36 MATERIALS SCIENCE↗

Dynamic energy absorption characteristics of hollow microlattice structures

Hollow microlattice structures are promising candidates for advanced energy absorption and their characteristics under dynamic crushing are explored. The energy absorption can be significantly enhanced by inertial stabilization, shock wave effect and strain rate hardening effect. In this paper we combine theoretical analysis and comprehensive finite element method simulation to decouple the three effects, and then obtain a simple model to predict the overall dynamic effects of hollow microlattice structures. Inertial stabilization originates from the suppression of sudden crushing of the microlattice and its contribution scales with the crushing speed, v. Shock wave effect comes from the discontinuity across the plastic shock wave front during dynamic loading and its contribution scales with e. The strain rate effect increases the effective yield strength upon dynamic deformation and increases the energy absorption density. A mechanism map is established that illustrates the dominance of these three dynamic effects at a range of crushing speeds. Compared with quasi-static loading, the energy absorption capacity a dynamic loading of 250 m/s can be enhanced by an order of magnitude. The study may shed useful insight on designing and optimizing the energy absorption performance of hollow microlattice structures under various dynamic loads. (C) 2014 Elsevier Ltd. All rights reserved.

Liu, YL↗

Investigating ceramic breeder pebble beds thermomechanics evolution using novel pressure mapping technology

Ceramic breeder pebble beds undergo complex thermomechanical interactions during blanket operation due to stress build-up and relaxation under the effects of confined thermal expansion, thermal cycling, and creep. Understanding the evolution of such processes can aid in guiding blanket design/assembly, breeder materials developments, predicting performance and possible failure modes. This study introduces experimental techniques that enable us to create an environment in which the pebble bed stresses are organically generated as a result of relevant temperature gradients and magnitudes that allows us to observe the combined thermomechanical interaction effects. A novel non-intrusive in-situ tactile pressure sensing technology is used to generate real-time contact pressure maps revealing the spatial and temporal stress evolution with emphasis on understanding the roles that each of the thermo-mechanical forces play in dictating the pebble bed’s equilibrium conditions. Two types of bed-wall contact pressure drop were recorded: (1) within the subsequent cycles due to pebbles irreversible rearrangements, and (2) within the cycle itself as a result of creep/stress-relaxation. Consequently, by the fourth cycle, the contact pressure drops to negligible values and remains stable. This stability is attributed to two modes of self-regulation: (1) stress self-regulation as a result of pressure rise and fall due to thermal expansion and creep/thermal cycling, respectively, and (2) temperature self-regulation due to the locally enhanced thermal conductivity in the core region of the bed accompanied by deteriorated interface conductance. These two mechanisms are desirable as they lower the probability of the events of pebbles crushing and thermal runaways under high temperatures/stresses and poor heat extraction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mechanical properties of reconstituted Australian black coal

Coal is usually highly heterogeneous. Great variation in properties can exist among samples obtained even at close proximity within the same seam or within the same core sample. This makes it difficult to establish a correlation between uniaxial compressive strength (UCS) and point load index for coal. To overcome this problem, a method for making reconstituted samples for laboratory tests was developed. Samples were made by compacting particles of crushed coal mixed with cement and water. These samples were allowed to cure for four days. UCS and point load tests were performed to measure the geomechanical properties of the reconstituted coal. After four days curing, the average UCS was found to be approximately 4 MPa. This technical note outlines some experimental results and correlations that were developed to predict the mechanical properties of the reconstituted black coal samples. By reconstituting the samples from crushed coal, it is hoped that the samples will retain the important mechanical and physicochemical properties of coal, including the swelling, fluid transport, and gas sorption properties of coal. The aim is to be able to produce samples that are homogeneous with properties that are highly reproducible, and the reconstituted coal samples can be used for a number of research areas related to coal, including the long-term safe storage of CO{sub 2} in coal seams.

01 COAL, LIGNITE, AND PEAT↗

The role of frequency on fretting corrosion of Alloy 690TT against 304 stainless steel in high temperature high pressure water

Highlights: • Delamination, material transfer and oxidation dominated fretting corrosion behavior in HTHP water. • Delamination was pure mechanical wear to produce fresh surface exposed to HTHP water for oxidation. • Increased frequency enhanced the maximum thickness of oxide film in worn surface. • Increased frequency accelerated the formation of tribologically transformed structure (TTS). • Increased frequency accelerated the escape of wear debris, which originated from the TTS and crushed oxide particles. - Abstract: In high temperature high pressure (HTHP) water, the role of frequency in fretting corrosion behavior and mechanism of Alloy 690TT against Type 304 stainless steel were investigated. Results indicated that wear mechanisms of delamination, material transfer and oxidation collectively dominated the fretting corrosion behavior. The delamination was related to pure mechanical wear to produce fresh surface exposed to HTHP water for oxidation, resulting in the increase of wear depth and volume. The increasing frequency played little role in oxide type of worn surfaces, which consisted of (Ni,Fe)(Fe,Cr){sub 2}O{sub 4} and Cr{sub 2}O{sub 3}. However, it enhanced the maximum thickness of oxide film in the worn surface. The increasing frequency resulted in the acceleration of the formation of nanostructured tribologically transformed structure (TTS) layer because it could aggravate the plastic deformation and increase the contact temperature for dynamic recrystallization. The increasing frequency accelerated the escape of the ultra-fine grained wear debris, which originated from not only the damage of TTS layer but also the crushed oxide particles generated in the contact gap.

36 MATERIALS SCIENCE↗

Investigation of the Critical State in Soil Mechanics Using DEM

The existence and uniqueness of the so-called critical state in soil mechanics is validated in our DEM simulations of irregular polygonal particles. For different particle shape characteristics, the critical state is independent of the initial stress and density conditions. We retain low stress levels, since we do not take into account the crushing of particles. In biaxial test simulations isotropic particles evolve toward a limiting state in which the system reaches a critical void ratio and deforms with constant volume, deviatoric stress, fabric anisotropy, and mechanical coordination number. The last one has been found to be the first variable to attain a critical value making possible for the rest of micro-and-macro-mechanical variables the convergence to the critical state. In periodic shear cell tests, for large shear deformations samples with anisotropic particles reach at the macro-mechanical level the same critical value for both shear force and void ratio. At the micro-mechanical level the components of the stress tensor, the fabric tensor and the inertia tensor of the particles also reach the same stationary state. By varying the aspect ratio of the particles we stated the strong influence of particle shape anisotropy on the parameters that the granular packing attained at the critical state.

36 MATERIALS SCIENCE↗

A non-isothermal breakage-damage model for plastic-bonded granular materials incorporating temperature, pressure, and rate dependencies

Plastic-bonded granular materials (PBM) are widely used in industrial sectors, including building construction, abrasive applications, and defense applications such as plastic-bonded explosives. The mechanical behavior of PBM is highly nonlinear, irreversible, rate dependent, and temperature sensitive governed by various micromechanical attributions such as grain crushing and binder damage. This paper presents a thermodynamically consistent, microstructure-informed constitutive model to capture these characteristic behaviors of PBM. Key features of the model include a breakage internal variable to upscale the grain-scale information to the continuum level and to predict grain size evolution under mechanical loading. In addition, a damage internal state variable is introduced to account for the damage, deterioration, and debonding of the binder matrix upon loading. Temperature is taken as a fundamental external state variable to handle non-isothermal loading paths. The proposed model is able to capture with good accuracy several important aspects of the mechanical properties of PBM, such as pressure-dependent elasticity, pressure-dependent yield strength, brittle-to-ductile transition, temperature dependency, and rate dependency in the post-yielding regime. Furthermore, the model is validated against multiple published datasets obtained from confined and unconfined compression tests, covering various PBM compositions, confining pressures, temperatures, and strain rates.

Breakage↗

Enabling Particulate Materials Processing Science for High-Consequence, Small-Lot Precision Manufacturing

This Laboratory Directed Research and Development project developed and applied closely coupled experimental and computational tools to investigate powder compaction across multiple length scales. The primary motivation for this work is to provide connections between powder feedstock characteristics, processing conditions, and powder pellet properties in the context of powder-based energetic components manufacturing. We have focused our efforts on multicrystalline cellulose, a molecular crystalline surrogate material that is mechanically similar to several energetic materials of interest, but provides several advantages for fundamental investigations. We report extensive experimental characterization ranging in length scale from nanometers to macroscopic, bulk behavior. Experiments included nanoindentation of well-controlled, micron-scale pillar geometries milled into the surface of individual particles, single-particle crushing experiments, in-situ optical and computed tomography imaging of the compaction of multiple particles in different geometries, and bulk powder compaction. In order to capture the large plastic deformation and fracture of particles in computational models, we have advanced two distinct meshfree Lagrangian simulation techniques: 1.) bonded particle methods, which extend existing discrete element method capabilities in the Sandia-developed , open-source LAMMPS code to capture particle deformation and fracture and 2.) extensions of peridynamics for application to mesoscale powder compaction, including a novel material model that includes plasticity and creep. We have demonstrated both methods for simulations of single-particle crushing as well as mesoscale multi-particle compaction, with favorable comparisons to experimental data. We have used small-scale, mechanical characterization data to inform material models, and in-situ imaging of mesoscale particle structures to provide initial conditions for simulations. Both mesostructure porosity characteristics and overall stress-strain behavior were found to be in good agreement between simulations and experiments. We have thus demonstrated a novel multi-scale, closely coupled experimental and computational approach to the study of powder compaction. This enables a wide range of possible investigations into feedstock-process-structure relationships in powder-based materials, with immediate applications in energetic component manufacturing, as well as other particle-based components and processes.

36 MATERIALS SCIENCE↗

Experimental determination of single-crystal halite thermal conductivity, diffusivity and specific heat from -75°C to 300°C

The thermal properties of halite have broad practical importance, from design and long-term modeling of nuclear waste repositories to analysis and performance assessment of underground natural gas, petroleum and air storage facilities. Using a computer-controlled transient plane source method, single-crystal halite thermal conductivity, thermal diffusivity and specific heat were measured from -75°C to 300°C. These measurements reproduce historical high-temperature experiments and extend the lower temperature extreme into cryogenic conditions. Measurements were taken in 25-degree increments from -75°C to 300°C. Over this temperature range, thermal conductivity decreases by a factor of 3.7, from 9.975 to 2.699 W/mK , and thermal diffusivity decreases by a factor of 3.6, from 5.032 to 1.396 mm²/s. Specific heat does not appear to be temperature dependent, remaining near 2.0 MJ/m³K at all temperatures. This work is intended to develop and expand the existing dataset of halite thermal properties, which are of particular value in defining the parameters of salt storage thermophysical models. The work was motivated by a need for thermal conductivity values in a mixture theory model used to determine bulk thermal conductivity of reconsolidating crushed salt.

58 GEOSCIENCES↗

Ice Load Project Final Technical Report

As interest and investment in offshore wind projects increase worldwide, some turbines will be installed in locations where ice of significant thickness forms on the water surface. This ice moves under the driving forces of wind, current, and thermal effects and may result in substantial forces on bottom-fixed support structures. The North and Baltic Seas in Europe have begun to see significant wind energy development and the Great Lakes of the United States and Canada may host wind energy development in the near future. Design of the support structures for these projects is best performed through the use of an integrated tool that can calculate the cumulative effects of forces due to turbine operations, wind, waves, and floating ice. The dynamic nature of ice forces requires that these forces be included in the design simulations, rather than added as static forces to simulation results. The International Electrotechnical Commission (IEC) standard[2] for offshore wind turbine design and the International Organization for Standardization (ISO) standard[3] for offshore structures provide requirements and algorithms for the calculation of forces induced by surface ice; however, currently none of the major wind turbine dynamic simulation codes provides the ability to model ice loads. The scope of work of the project described in this report includes the development of a suite of subroutines, collectively named IceFloe, that meet the requirements of the IEC and ISO standards and couples with four of the major wind turbine dynamic simulation codes. The mechanisms by which ice forces impinge on offshore structures generally include the forces required for crushing of the ice against vertical-sided structures and the forces required to fracture the ice as it rides up on conical-sided structures. Within these two broad categories, the dynamic character of the forces with respect to time is also dependent on other factors such as the velocity and thickness of the moving ice and the response of the structure. In some cases, the dynamic effects are random and in other cases they are deterministic, such as the effect of structural resonance and coupling of the ice forces with the defection of the support structure. The initial versions of the IceFloe routines incorporate modules that address these varied force and dynamic phenomena with seven alternative algorithms that can be specified by the user. The IceFloe routines have been linked and tested with four major wind turbine aeroelastic simulation codes: FAST, a tool developed under the management of the National Renewable Energy Laboratory (NREL) and available free of charge from its web site; Bladed[4], a widely-used commercial package available from DNV GL; ADAMS[5], a general purpose multi-body simulation code used in the wind industry and available from MSC Software; and HAWC2[6], a code developed by and available for purchase from Danmarks Tekniske Universitet (DTU). Interface routines have been developed and tested with full wind turbine simulations for each of these codes and the source code and example inputs and outputs are available from the NREL website.

17 WIND ENERGY↗

Salt Reconsolidation and Repository Engineered Barriers - 18651

Salt repositories for the permanent disposal of hazardous waste provide extraordinary advantage over other geo-media because geotechnical barriers can be constructed with confidence using crushed salt, which is a perfectly compatible material that is readily available by mining practice. Other excellent barrier materials that consist of specialty mixes of salt-based concrete, bentonite, and bitumen bolster confidence that a repository in geologic salt formations will remain impermeable forever. Practically speaking, achieving high-performance engineered barriers assumes an isolation role as important as the host formation itself. Long-term performance assessment intrinsically includes evaluating seal-system design and demonstrated operational characteristics. Consistent with global interests, specific research on salt-repository seal systems not only established significant technical bases but identified possible improvements through straightforward research and laboratory and field investigations. Engineered barriers of crushed salt with possible additives, such as clay and water, evolve to create hydrological and mechanical characteristics that approach those of the host salt formation. Demonstrating early functionality of seal systems reduces uncertainty, which is introduced when calculating or predicting when performance properties become effective in the future. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Determination of Static and Dynamic Crush Strengths of Stainless Steel Honeycomb Material

Honeycomb structures are ideal energy absorbers due to the high axial strength compared to the low density of the material and consistent mechanical properties. Lighter density materials used in honeycomb structures, like aluminum, have been studied intensively because of their use in aerospace applications. However, relatively denser materials like stainless steel have been less studied. The purpose of this project is to determine if 304 Stainless Steel hexagonal honeycomb can be used in applications related to the field of radioactive material packaging by determining the crush strength of the structure.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The Combined Finite-Discrete Element Method applied to the Study of Rock Fracturing Behavior in 3D

Since its introduction the combined finite-discrete element method (FEM/DEM), has become an excellent tool to address a wide range of problems involving fracturing and fragmentation of solids. Within the context of rock mechanics, the FEM/DEM method has been applied to many complex industrial problems such as block caving, deep mining techniques, rock blasting, seismic waves, packing problems, rock crushing problems, etc. In the real world most of the problems involving fracture and fragmentation of solids are three dimensional problems. With the aim of addressing these problems an improved 2D/3D FEM/DEM capability has been developed at Los Alamos National Laboratory (LANL). These capabilities include state of the art 3D contact detection, contact interaction, constitutive material models, and fracture models. In this paper, Split Hopkinson Pressure Bar (SHPB) Brazilian experiments are simulated using this improved 2D/3D FEM/DEM approach which is implemented in LANL's MUNROU (Munjiza-Rougier) code. The results presented in this work show excellent agreement with both the SHPB experiments and previous 2D numerical simulations performed by other FEM/DEM research groups.

CALCULATION METHODS↗

Assessment of the Idaho National Laboratory Remote Handled Low Level Waste Disposal Facility Hydraulic Performance

This document provides a summary of the expected hydraulic performance of the vault drainage system installed at Idaho National Laboratory’s Remote Handled Low-Level Waste disposal facility. Hydraulic performance was assessed through analysis of the mechanical properties of the drainage system and backfill materials, including material gradation and proctor data; laboratory data, including bulk density, porosity, unsaturated hydraulic conductivity, moisture-retention data, and van Genuchten parameters; and field-data collected using in-situ instrumentation with data collected during a vault-scale infiltration characterization test. Hydraulic performance of the vault drainage system was designed to promote a greater than 500-year vault concrete longevity. The predicted hydraulic performance is, in part, a function of the materials used in construction, sequencing of the hydraulic drainage materials, and the as-built condition of the materials following compaction necessary to ensure vault stability. Specifying specific as-built hydraulic properties is exceedingly difficult at the facility specification/design phase. Instead, material mechanical properties were specified and confirmed early during the construction process. As the drainage materials were installed, samples were sent to a laboratory for hydraulic property testing and, after drainage system installation was complete around the performance assessment vaults, a field-scale infiltration test was conducted with data collection to verify the as-built hydraulic performance. This report provides summary data for the measured mechanical properties, laboratory data, and field infiltration characterization test data. Mechanical data have relatively little variability because of the sieve system used when the materials were crushed onsite. Laboratory data were obtained for a relatively small number of material samples, but the data obtained for each sample are extensive. However, laboratory data provide the moisture retention relationships and relative hydraulic conductivity-moisture content relationships for uninstalled materials. Conducting field-scale infiltration tests with collection of moisture retention data and wetting front propagation data allows extension of laboratory data to the as-installed conditions of the vault drainage system. These combined data types are integrated using a numerical simulation of the infiltration characterization test to refine model parameters. The infiltration characterization model will be used to support the hydraulic and concrete performance of the vault system provided in the facility performance assessment.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Mechanical Characteristics of SiC Coating Layer in TRISO Fuel Particles

Tristructural isotropic (TRISO) particles are considered as advanced fuel forms for a variety of fission platforms. While these fuel structures have been tested and deployed in reactors, the mechanical properties of these structures as a function of production parameters need to be investigated in order to ensure their reliability during service. Nanoindentation techniques, indentation crack testing, and half sphere crush testing were utilized in order to evaluate the integrity of the SiC coating layer that is meant to prevent fission product release in the coated particle fuel form. The results are complimented by scanning electron microscopy (SEM) of the grain structure that is subject to change as a function of processing parameters and can alter the mechanical properties such as hardness, elastic modulus, fracture toughness and fracture strength. Through utilization of these advanced techniques, subtle differences in mechanical properties that can be important for in-pile fuel performance can be distinguished and optimized in iteration with processing science of coated fuel particle production.

99 GENERAL AND MISCELLANEOUS↗

Development of a Modular, Crushed-Rock Thermal Energy Storage Pilot Design

The goal of this project, primarily funded by the U.S. Department of Energy, is to design a next-step pilot to advance near-term energy storage integrated with a fossil plant to provide a facility capable of being viable and effective in a market with growing penetration of variable renewable energy (VRE). Thermal energy storage (TES) represents an ideal technology for this purpose. The current effort will complete a feasibility study to prepare for the Phase II pre-front end engineering design (pre-FEED) for implementing a crushed-rock TES system integrated with a natural gas combined cycle (NGCC) plant. The crushed rock storage technology, which is being developed by Brenmiller Energy, is a modular TES system termed bGen™, which can accommodate both thermal and electrical inputs and output steam, hot water, or hot air. For this application, the estimated efficiency is 80% thermal to thermal. The TES technology is being designed to operate on a slipstream from NYPA’s Eugene W. Zeltmann Power Project (Zeltmann) natural gas combined cycle (NGCC) plant. The projected size of the system will be up to 4 MWe with at least 4 hours of storage duration, or 16 MWh-e total. Final sizing is being determined during the ongoing feasibility study. The next-step pilot being designed as part of the current project will represent a 5-fold increase in scale for this TES technology, and will be used to validate the technology’s ability to provide effective and economical energy storage. This pilot would represent the next-to-last demonstration scale before the technology could be commercial ready at GWh-e scales in the 2030 timeframe. This project is expected to design the critical next-step pilot, which will be undertaken in real-world operating conditions to better determine the crushed rock TES technology’s ability to be integrated with an NGCC plant and assess degradation over transient cycling at rates befitting various marketplaces. The crushed-rock TES pilot design is a technically feasible next step in the development of the technology and is built upon years of prior testing and demonstration. The proposed TES technology was developed by Brenmiller over the last 8 years and has been tested in 3 generations of demonstration units at various sites, globally. During this field testing, different characteristics and performance of the technology were validated, including the following key features: energy storage capacity, energy storage charge/discharge rate, energy storage loses, energy storage mechanical testing. This presentation will provide an update on the results of the conceptual design study for the modular crushed-rock TES system, integrated with a NGCC power plant.

03 NATURAL GAS↗