Search NASA⌕ Search

SEARCH · Search NASA

Results for “metallography”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Evaluation of tantalum-alloy-clad uranium mononitride fuel specimens from 7500-hour, 1040 C pumped-lithium-loop test

Simulated nuclear fuel element specimens, consisting of uranium mononitride (UN) fuel cylinders clad with tungsten-lined T-111, were exposed for up to 7500 hr at 1040 C (1900 F) in a pumped-lithium loop. The lithium flow velocity was 1.5 m/sec (5 ft/sec) in the specimen test section. No evidence of any compatibility problems between the specimens and the flowing lithium was found based on appearance, weight change, chemistry, and metallography. Direct exposure of the UN to the lithium through a simulated cladding crack resulted in some erosion of the UN in the area of the defect. The T-111 cladding was ductile after lithium exposure, but it was sensitive to hydrogen embrittlement during post-test handling.

Watson, G. K.↗
NASA NTRS1973

Report on Skylab -M551 samples

The results of examining the Skylab M551 specimens are reported. The tests performed include visual examination, thickness and distortion measurements, radiographic inspection, sectioning, and optical metallography. It is concluded that gravity induced convection played a significant role in determining the aluminum oxide distribution on ground characterization samples, but not on the Skylab sample.

Source record↗
NASA NTRS1973

Effects of diffusion on aluminum depletion and degradation of NiAl coatings

Experimental demonstration of the effects of diffusion on aluminum depletion and degradation in NiAl coatings on superalloys. Pack aluminized IN 100 and Mar-M200 were vacuum annealed at 1100 C to allow diffusion to proceed independently of oxidation. As-coated and as-diffused coatings were compared before and after cyclic furnace oxidation at 1100 C. The extent of degradation was judged by specific weight change, metallography, and electron microprobe analyses.

Smialek, J. L.↗
NASA NTRS1974

Behavior of ceramics at 1200 C in a simulated gas turbine environment

This report summarizes programs at the NASA Lewis Research Center evaluating several classes of commercial ceramics, in a high gas velocity burner rig simulating a gas turbine engine environment. Testing of 23 ceramics in rod geometry identified SiC and Si3N4 as outstanding in resistance to oxidation and thermal stress and identified the failure modes of other ceramics. Further testing of a group of 15 types of SiC and Si3N4 in simulated vane shape geometry has identified a hot pressed SiC, a reaction sintered SiC, and hot pressed Si3N4 as the best of that group. SiC and Si3N4 test specimens were compared on the basis of weight change, dimensional reductions, metallography, fluorescent penetrant inspection, X-ray diffraction analyses, and failure mode.

Sanders, W. A.↗
NASA NTRS1974

Role of HF and Zr in the hydrogen embrittlement of Ta and Cb alloys

An attempt is made to characterize the hydrogen embrittlement of aged T-111 and similar Ta and Cb alloys and to describe the mechanisms believed responsible for the increased sensitivity of T-111 to low temperature hydrogen embrittlement after aging for 1000 hr or longer near 1040 C. A total of eight Ta-base alloys and two Cb-base alloys were investigated. The effects of pre-age annealing temperature, aging time, temperature and environment, and alloy composition on the susceptibility to hydrogen embrittlement were investigated. The primary method of determining the effects of these variables on the ductility of T-111 was by bend testing at 25 and -196 C. Fractured specimens were examined by the scanning electron microscope, electron microprobe, metallography, and X-ray diffraction.

Stephens, J. R.↗
NASA NTRS1974

The effect of microstructure on the fracture toughness of titanium alloys

The microstructure of the alpha titanium alloy Ti-5Al-2.5Sn and the metastable beta titanium alloy Beta 3 was examined. The material was from normal and extra low interstitial grade plates which were either air-cooled or furnace-cooled from an annealing treatment. Beta 3 was studied in alpha-aged and omega-aged plates which were heat treated to similar strength levels. Tensile and plane strain fracture toughness tests were conducted at room temperature on the alpha-aged material. The microstructure and fracture mechanisms of alloys were studied using optical metallography, electron microscopy, microprobe analyses, and texture pole figures. Future experiments are described.

Vanstone, R. H.↗
NASA NTRS1975

Hot corrosion evaluation of aluminide coated superalloys in support of an ASTM Round Robin program

Commercial aluminized coatings on substrates were hot corroded at 900 C in a 0.3 Mach burner rig with 5 ppm synthetic sea salt and at two cycling frequencies. Extensive post-exposure examinations were conducted on the corroded specimens such as metallography, X-ray diffraction, scanning electron microscopy, microprobe raster scans, and spectrographic analyses. Thermodynamic calculations were made of the equilibrium burner flame composition and the calculations were compared to the experimental findings. It was found that localized spalling of the coatings preceded coating failure. It is suggested that the spalling of the coatings is due to the formation of localized stresses caused by the depletion of chromium and aluminum in the coating or the enrichment of the coating with sulfur. For the materials and test conditions investigated, it was found that coating life is dependent only upon the initial coating thickness and not on the type of aluminized coating, the substrate, or the cycle frequency.

Santoro, G.↗
NASA NTRS1974

High gas velocity burner tests on silicon carbide and silicon nitride at 1200 C

Ten SiC materials and five Si3N4 materials were exposed in a Mach 1-gas-velocity burner simulating a gas-turbine engine environment. All materials studied are commercially available. Cyclic tests up to 100 hours' duration were conducted at specimen temperatures of 1200 C. A specimen geometry was used that develops thermal stresses during thermal cycling in a manner similar to blades and vanes of a gas turbine engine. Materials were compared on a basis of weight change, dimensional reductions, metallography, fluorescent-penetrant inspection, X-ray diffraction analyses, failure mode, and general appearance. One hot-pressed SiC, one reaction-sintered SiC, and three hot-pressed Si3N4 materials survived the program goal of 100 one-hour cycles of exposures. Of the materials that failed to meet the program goal, thermal fatigue was identified as the exclusive failure mode.

Sanders, W. A.↗
NASA NTRS1975

Combustion of bulk titanium in oxygen

The combustion of bulk titanium in one atmosphere oxygen is studied using laser ignition and several analytical techniques. These were high-speed color cinematography, time and space resolved spectra in the visible region, metallography (including SEM) of specimens quenched in argon gas, X-ray and chemical product analyses, and a new optical technique, the Hilbert transform method. The cinematographic application of this technique for visualizing phase objects in the combustion zone is described. The results indicate an initial vapor phase reaction immediately adjacent to the molten surface but as the oxygen uptake progresses the evaporation approaches the point of congruency and a much reduced evaporation rate. This and the accumulation of the various soluble oxides soon drive the reaction zone below the surface where gas formation causes boiling and ejection of particles. The buildup of rutile cuts off the oxygen supply and the reaction ceases.

Clark, A. F.↗
NASA NTRS1975

Continued development of abradable gas path seals

Major program objectives were the continued development of NiCrAlY feltmetal and honeycomb systems for knife edge seal applications in the 1144 to 1366 K temperature range, and to initiate abradable seal material evaluation for blade tip seal applications in the 1366 to 1589 K temperature range. Larger fiber size, higher density feltmetal showed greatly improved erosion resistance with a slight reduction in abradability compared to the baseline feltmetal. Pack aluminide coating of the honeycomb extended the oxidation resistance and slightly improved the abradability of this material. Evaluation through selected abradability, erosion and oxidation testing, and pertinent metallography led to selection of a plasma sprayed yttria stabilized zirconia (ZrO2)/CoCrAlY layered system as the system with the most potential to meet the 1589 K requirement for blade tip seals. This system demonstrated structural integrity, erosion resistance, and some degree of abradability.

Shiembob, L. T.↗
NASA NTRS1976

Axial fatigue of /0, +30, and -30 deg/6s graphite/epoxy

Results are presented for an investigation carried out on a /0, +30, and -30 deg/6s graphite/epoxy angle-ply laminate in order to characterize the overall fatigue behavior, to evaluate strength/moduli degradation due to cyclic loading, and to identify the failure modes and mechanisms. The specimen life determined from fatigue tests is measured as a function of cyclic stress amplitude for various stress ratios. Fractured specimens are sectioned and examined by conventional metallography and SEM to reveal failure modes and mechanisms. It is shown that the laminate studied is susceptible to axial fatigue failures under cyclic loading which involves both tensile and compressive mean stresses. Fracture surface observations indicate the occurrence of complex failure modes. A variety of local failure mechanisms are identified.

Ramani, S. V.↗
NASA NTRS1976

Chemical vapor deposition growth

A laboratory type CVD reactor system with a vertical deposition chamber and sample pedestal heated by an external RF coil has been extensively modified by installation of mass flow controllers, automatic process sequence timers, and special bellows-sealed air-operated valves for overall improved performance. Various film characterization procedures, including classical metallography, SEM analyses, X ray diffraction analyses, surface profilometry, and electrical measurements (resistivity, carrier concentration, mobility, spreading resistance profiles, and minority-carrier lifetime by the C-V-t method) area used to correlate Si sheet properties with CVD parameters and substrate properties. Evaluation procedures and measurements are given. Experimental solar cell structures were made both in epitaxial Si sheet (on sapphire substrates) and in polycrystalline material on alumina substrates, the former to provide an indication of what might be an upper limit on performance of the latter. Preliminary results are given, as obtained in cell structures not specially designed to allow for the unique properties of the sheet material, and fabricated in material known to be far from optimum for photovoltaic performance. Low power conversion efficiencies have been obtained in the epitaxial as well as the polycrystalline Si sheet.

Ruth, R. P.↗
NASA NTRS1977

Diffusion welding of a directionally solidified gamma/gamma prime - delta eutectic alloy

Hot-press diffusion welding parameters were developed for a directionally solidified, gamma/gamma prime-delta eutectic alloy. Based on metallography, a good diffusion weld was achieved at 1100 C under 34.5 MPa (5 ksi) pressure for 1 hour. In addition, a dissimilar metal weld between gamma/gamma prime-delta and IN-100 was successfully made at 1100 C under 20.7 MPa (3 ksi) pressure for 1 hour.

Moore, T. J.↗
NASA NTRS1977

Creep and tensile properties of several oxide-dispersion-strengthened nickel-base alloys at 1365 K

The tensile properties at room temperature and at 1365 K and the tensile creep properties at low strain rates at 1365 K were measured for several oxide-dispersion-strengthened (ODS) alloys. The alloys examined included ODS Ni, ODS Ni-20Cr, and ODS Ni-16Cr-Al. Metallography of creep tested, large grain size ODS alloys indicated that creep of these alloys is an inhomogeneous process. All alloys appear to possess a threshold stress for creep. This threshold stress is believed to be associated with diffusional creep in the large grain size ODS alloys and normal dislocation motion in perfect single crystal (without transverse low angle boundaries) ODS alloys. Threshold stresses for large grain size ODS Ni-20Cr and Ni-16Cr-Al type alloys are dependent on the grain aspect ratio. Because of the deleterious effect of prior creep on room temperature mechanical properties of large grain size ODS alloys, it is speculated that the threshold stress may be the design limiting creep strength property.

Wittenberger, J. D.↗
NASA NTRS1977

Closed-cell foams produced from sputter-deposited aluminum

Sputter deposited aluminum containing argon was melted to produce foam, both in the earth's gravitational field and in a zero-gravity space environment. Experiments leading to trapping of up to 270 ppm argon sputtering gas in pure aluminum during high-rate dc triode sputter deposition are discussed. Conduct of the melting experiments and design of the furnace used are described. Metallography; an analysis of bubble size, distribution, and morphology; and a preliminary description of the kinetics are also presented.

Patten, J. W.↗
NASA NTRS1977

Inclusions, grain boundaries and hydrogen attack

Optical metallography, scanning electron microscopy, and X-ray spectrometry were used to study the roles of grain boundaries and inclusions in the nucleation process and fissure growth during the rapid stage of hydrogen attack on 1020 steel in the annealed condition at temperatures up to 600 C and a hydrogen pressure of 10.3 MN/sq m. It is found that intergranular fracture occurred when specimens were fractured at 77 K after hydrogen exposure and that macroscopically observable fissures formed due to the coalescence of bubbles which nucleated at inclusions in grain boundaries. The inclusions are tentatively identified as MnS.

Shih, H. M.↗
NASA NTRS1976

Experiments to evaluate high-temperature rolling as a low-cost process for silicon solar cells

Mechanical rolling (a process used in industry for producing large quantities of metallic sheet and strip) has been suggested for the rapid low-cost manufacture of silicon sheet to be used for photovoltaic power generation equipment, such as solar arrays. The advantages of rolling include: high rates of production, wide sheets as products, good control of dimension, and (in the case of solar grade silicon) minimal development of impurities. Experiments have been performed using high-temperature, high-speed compression of polycrystalline silicon cylinders. Metallography and X-ray diffraction techniques have been used to examine the samples both before and after compression, and a model process has been designed to evaluate the technical practicality and economic feasibility of the method.

Noel, G. T.↗