Search NASA⌕ Search

SEARCH · Search NASA

Results for “mode cycling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Electrochemical Characterization of Degradation Modes of High-Voltage Li x Ni 0.33 Mn 0.33 Co 0.33 O 2 Electrodes

While deeply charged high-voltage cathodes can improve battery energy density, understanding and preventing any accelerated cell degradation is crucial to practical success. Here, to analyze the degradation of LiNi x Mn y Co 1–x–y O 2 (NMC) type material charged to 4.3 and 4.5 V, a physics-based model is applied to cycling data to obtain parameter estimates indicative of degradation modes, which are validated by simple electrochemical measurements and further interpreted by materials characterization. Growth rates of interfacial impedance and active material loss are greater at 4.5 V, as might be expected. However, when charged to 4.5 V, degradation rates are initially lower at a cycling C-rate of 1.0 C than at 0.5 C. Once degradation mode changes are quantified, simulations evaluate the contribution of individual degradation mode to performance losses and provide estimates of the energy-power correlation (Ragone plots) of cells after cycling.

25 ENERGY STORAGE↗
DOE OSTI2022

A Comparison of High Intensity Proton Efficiencies for Rf Harmonics 1 and 2

There have been many changes to the Booster setup over the past seven years, but the most fundamental physical change is probably the change from an Rf harmonic of 2 to 1. By looking at the intensity data over this period it is possible to compare the running efficiencies in each case. The harmonic change occurred at the beginning of the 1998 run. Another fundamental, though administrative, change that occurred after the 1998 run was the advent of ALARA alarms that limit the amount of beam loss that is allowed to occur during different parts of the cycle. These ALARA alarm limits also depend on the AGS repetition period since it is the amount of beam energy lost per unit time that is used as the criterion for these alarms. The 1998 h=1 run did not have an ALARA constraint, but subsequent h=1 runs did have that constraint. The highest Booster proton intensity was obtained in the h=2 mode (about 23 Tp). At best, the h=1 mode only yielded about 20 Tp per cycle. Is it because the h=2 setup can produce higher intensity than the h=1 setup that the h=2 intensity was higher, or is it because other factors are responsible? This note seeks to shed some light on this question. In order to compare the two setups (h=1 vs. h=2) intensity scaler data was taken from the setup books over the past seven years. In general, this data was taken when the Booster was in an optimized state. What ‘optimized’ means is not so clearly defined, but would typically mean that the Booster configuration was ‘optimized’ so that it yields the highest intensity late in the AGS given physical and other constraints.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Coupled Bunch Instabilities Growth in the Fermilab Booster during Acceleration Cycle

Currently, Fermilab Booster accelerates ~4.5E12 protons per pulse (ppp) in 81 bunches from 400 MeV to 8 GeV at 15 Hz to provide beam to multiple HEP experiments and is being upgraded to handle higher beam intensity >6.7E12 ppp at a repetition rate of 20 Hz. In the current mode of operation, we control longitudinal coupled bunch instabilities (LCBI) using combination of passive and active dampers. The issues with LCBI are expected to worsen at higher beam intensities. Here, we would like to investigate at what time in the beam cycle a particular mode is going to originate and how much it contributes at a different time of the acceleration cycle using the collected wall current monitor data from injection to extraction. Also, measure growth rates as a function of beam intensity for some dominant modes. Finally, this paper presents results from the observed LCBI analysis for the highest available beam intensities, unexpected findings, and future plans to mitigate the LCBI at higher beam intensities

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Optimal management of electric hotel loads in mild hybrid heavy duty truck

Here, the problem of engine idling for heavy-duty trucks has been under study for decades with Auxiliary Power Units (APUs) and Truck Stop Electrification (TSE) as the most compelling solutions. With the electrification of trucks approaching feasibility in terms of cost-effective technology, hybridization offers another “degree of freedom” to tackle the problem. Here, this work aims at exploiting a battery pack of a 48 V mild-hybrid heavy-duty truck to store sufficient onboard energy for powering the auxiliary loads during the hoteling. This problem is not trivial, as the battery packs typically cannot recover the entire energy required through regeneration alone; hence an optimal energy management strategy needs to be employed to charge the battery through the engine during drive operation. This strategy optimizes powertrain performances among the four modes: (i) Engine of Coasting (EOC), (ii) Regeneration by braking, (iii) Regeneration by engine, and (iv) engine idling. This paper presents the development of a Dynamic Programming (DP) framework that employs a multi-objective cost function to minimize the fuel consumption and maximize the regeneration using the above-mentioned four modes. A typical heavy-duty truck drive cycle is used to represent the drive phase, with mandatory hoteling stops as per regulations. A comprehensive powertrain model is developed using validated components’ model. The DP employs two state variables: battery State-of-Charge (SOC) and engine mode, and three control inputs: (i) the engine ON–OFF state, (ii) clutch engagement state, and (iii) power request at the Electric Machine (EM) for calculating optimal SOC trajectory. The framework also tackles rapid engine ON–OFF scenarios to avoid the challenges associated with DP and the compromises in fuel cost with those approaches. Finally, the effectiveness of the proposed framework is tested for potential fuel savings on two different battery packs by performing the full cycle simulations. The results show 6.47% of fuel consumption reduction as compared to traditional APU-based heavy-duty truck.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2026

The Influence of Mesoscale Particle Structure on the Electrode Degradation and Resultant Electrochemistry of Lithium Ion Cells With Nickel Rich Lithium Nickel Manganese Cobalt Oxide Positive Electrodes

Nickel-rich lithium nickel manganese cobalt oxide, NMC (LiNi x Mn y Co z O 2 ), materials are desirable positive electrodes in lithium ion batteries, providing high capacity and energy density. The mesoscale structure of NMC materials is commonly a polycrystalline aggregate, providing opportunity for short lithium ion transport distance of the small primary particles, yet facile material handling due to the larger secondary particles. On (de)lithiation the NMC unit cell changes volume, where the anisotropic strain can result in secondary particle fracture. This secondary particle fracture process during cycling has been associated with several degradation modes of NMC materials in LIBs. In this work, a milling process was determined whereby the secondary particles could be pre-fractured with retention of the parent primary particle crystallographic structure, crystallite size, and morphology, providing the ability to unambiguously determine the influence of NMC secondary particle size and mesostructure on resultant functional behavior. The bulk and interfacial properties and electrochemistry of as-received commercially obtained polycrystal NMC811 (LiNi 0.8 Mn 0.1 Co 0.1 O 2 , PC NMC) and its milled MPC NMC counterpart were compared. The smaller secondary particle size, higher surface area MPC NMC was found to result in 1) greater cathode tortuosity, 2) reduced surface Ni on the cycled MPC cathodes consistent with surface reconstruction, and 3) increased Ni deposition on the anodes from cathode-anode crosstalk. These factors manifested in unfavorable electrochemical behavior of MPC with lower functional capacity at both 1C and C/10 rates and higher impedance over extended moderate voltage (dis)charge cycling.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Aeroelastic oscillations of a pitching flexible wing with structural geometric nonlinearities: Theory and numerical simulation

In this paper, we focus on the derivation of an analytical model of the aeroelastic dynamics of an elastically mounted flexible wing. This equations of motion obtained serve to help understand the behaviour of the aeroelastic wind tunnel setup in question, which consists of a rectangular wing with a uniform NACA 0012 airfoil profile, whose base is free to rotate rigidly about a longitudinal axis. Of particular interest are the structural geometric nonlinearities primarily introduced by the coupling between the rigid body pitch degree-of-freedom and the continuous system. A coupled system of partial differential equations (PDEs) coupled with an ordinary differential equation (ODE) describing axial-bending-bending-torsion-pitch motion is derived using Hamilton's principle. A finite dimensional approximation of the system of coupled differential equations is obtained using the Galerkin method, leading to a system of coupled nonlinear ODEs. Subsequently, these nonlinear ODEs are solved numerically using Houbolt's method. The results that are obtained are verified by comparison with the results obtained by direct integration of the equations of motion using a finite difference scheme. Adopting a linear unsteady aerodynamic model, it is observed that the system undergoes coalescence flutter due to coupling between the rigid body pitch rotation dominated mode and the first flapwise bending dominated mode. Finally, the behaviour of the limit cycle oscillations is primarily influenced by the structural geometric nonlinear terms in the coupled system of PDEs and ODE.

42 ENGINEERING↗
DOE OSTI2024

Fuel Behavior Implications of Reactor Design Choices in Pressurized Water SMRs

Small pressurized water reactors (PWRs) can feature boron free operation, natural circulation mode, reduced height assemblies and/or long refueling cycles. This paper attempts to explore core design optimization for each of these design evolutions. In consequence, five core design layouts are developed incorporating boron free operation with continuous control rods insertion, natural circulation with low burnup/low power density design, natural circulation with high burnup/low power density design, forced circulation with standard core power density design, and forced circulation with high power density design. These cores’ performance is compared to a standard 4-loop PWR. The design process aims to improve the fuel cycle cost under safety constraints through core design optimization using CASMO4E/SIMULATE3 reactor physics codes and FRAPCON4.1 fuel performance assessment tool. Core modeling assumes standard 17x17 PWR fuel assemblies loaded with low enriched uranium (LEU) up to 5wt% or LEU+ (i.e., below 10wt% enrichment) pellets with gadolinium oxide (Gd2O3) as the burnable poison. Satisfactory core and fuel performances are obtained for all the designed cores under steady state and considered overpower transients. For low power density operation, long cycle lengths are achieved reaching a 2.5- and a 5-year cycles and peak rod-average burnup is pushed to 83 MWd/kgU. Other cycle lengths are maintained at 18 months. Boron free operation exhibits the ability to achieve longer cycle lengths at the cost of higher peaking factors leading to high local power and fuel temperatures which prevents sizable power uprates and is deemed uneconomical. Fuel assembly height reduction allows coolant velocity retrofit which enables higher core power density without violating structural integrity of the fuel assembly. As a result, a core power density of 123 kW/l is reached where total cladding hoop strain becomes the limiting parameter.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Damage Evolution of Double-Sided Copper Conductor on Multi-layer Flexible Substrate Under Bending

Abstract—Thin-film conductors continue to play an important role in flexible electronics, and thus, the performance and reliability of such conductors under mechanical loading such as stretch, bend, and twist need to be studied through experiments as well as simulations. This paper focuses on the damage evolution of the thin-film conductors under cyclic bending. Four types of double-sided copper conductors: straight trace without coverlay, straight trace with coverlay, notched trace without coverlay, and notched trace with coverlay on multi-layer substrates were studied in this work. The adaptive curvature flexure test method, which is suitable for thin-film bending, was employed in this work. Adaptive curvature flexure test is one where the flexible substrate with its conductor is positioned between two parallel plates, and the parallel plates are moved relative to each other such that the gap distance between the parallel plates changes in one of the configurations of the adaptive curvature flexure test. Different strain levels can be achieved easily in such an adaptive curvature flexure test by controlling the gap distance between the parallel plates. By subjecting flexible substrates with thin conductors to such bend tests, the fatigue life of the specimen was determined for different magnitudes of strain ranges. The results were then compared among the four types of conductors. Specimens were designed such that the conductors were placed on both sides of the substrate so that the one of the conductors would undergo tensile straining, while the other one would undergo compressive straining. It was shown that the fatigue life was highly dependent on the magnitude of strain range, and that the conductor on the compressive side failed sooner than that on the tensile side. The failed specimens were examined in a microscope at different number of cycles. Also, the resistance of the conductors, which is directly related to the reliability of thin-film conductors, was monitored in-situ during bending. The resistance change with the strain range change as well as the resistance progression with the number of cycles in tensile as well as compressive mode were determined, and such information is then used to create failure prediction models for thin-film conductors on flexible substrates.

damage evolution, flexible conductor, multi-layer ↗
DOE OSTI2023

Gas-Phase Composition as a Predictive Metric for Calendar Life Behavior of Next-Generation Silicon Anodes

The expansion of renewable technologies and electrification of the transportation sector is driving increased demand for next-generation battery materials that provide higher power and energy density with superior cycling and calendar life stability. Silicon (Si) has a theoretical capacity nearly 10x that of graphite, and is therefore a promising anode material candidate to meet these rigorous performance demands. While leading Si anode battery demonstrations are approaching target metrics for cycle life, a series of complex and interrelated modes of reactivity lead to reduced calendar life and therefore challenge practical adoption of these materials. Deconvoluting the degradation processes that impact Si calendar life is critical to informing the rational and accelerated design of improved Si materials. In the present work, we employ novel sampling techniques and GC-MS-FID characterization to measure gas-phase composition during initial Si cycling, which we tie to selective mechanisms of Si passivation. We utilize a tiered analysis approach to identify and quantify the gas-phase reaction products associated with three advanced Si material candidates under practical operating conditions. Ex situ analysis of Si powders (pure chemical reactivity) is coupled with nondestructive in situ sampling of Si electrodes in a practical pouch-cell format (coupled chemical and electrochemical reactivity). We link the observed gas-phase species evolution to electrochemical behavior and measured calendar life of the three Si materials. Further, we evaluate the voltage-resolved evolution of gas-phase species for one such Si nanomaterial, where nonmonotonic gas generation implies competition between passivating reaction pathways. The measured gas-phase compositional data serves as a critical input for our advanced electrochemical SEI models to identify favorable vs unfavorable reaction pathways to stabilize Si. In addition to bolstering a fundamental understanding of Si reactivity, the present approach informs specific and quantifiable gas-phase metrics tied to calendar life improvements in Si, which can streamline and accelerate the process of next-generation material development.

DIRECT ENERGY CONVERSION,ENERGY STORAGE↗
DOE OSTI2023

Turbulence and E × B flow correlations across the L-H transition in DIII-D deuterium and hydrogen plasmas

The isotope dependence of the low- to high confinement-mode (L- to H-mode) transition power threshold P LH presents significant challenges for the initial (non-nuclear) hydrogen operations phase of the international thermonuclear experimental reactor (ITER). Here, we examine the isotope dependence of turbulence and E × B flow correlation properties in the L-mode edge plasma, leading up to the L-H transition. At marginal auxiliary power (near P LH ), turbulence is initially suppressed periodically during limit cycle oscillations (LCO) that precede the transition to sustained H-mode confinement. Here, we present evidence that the long-range (toroidal) correlation of the E × B edge plasma flow across the LCO phase is much weaker in hydrogen than in deuterium in the DIII-D tokamak, congruent with the higher threshold power P LH required to access LCO and H-mode in hydrogen. Concomitantly, the time required to initially quench edge turbulence via localized edge E × B flow shear is significantly longer in hydrogen (1–1.5 ms) than in deuterium (approx. 100 µs). No toroidal long-range correlation of the turbulence amplitude is observed, in agreement with expectations based on the relatively short poloidal turbulence correlation length. Radial edge turbulence and flow correlation lengths are longer in deuterium than in hydrogen plasmas as one would expect from ‘naïve’ gyro-Bohm isotope transport scaling, despite the substantially higher thermal flux across the last closed flux surface in hydrogen before the L-H transition. This article is part of a discussion meeting issue 'H-mode transition and pedestal studies in fusion plasmas'.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Dynamics of coupled thermoacoustic modes: Noise and frequency spacing effects

Practical combustion systems consist of multiple thermoacoustic modes that are linearly stable or unstable at a wide range of frequencies. When coupled, the modal interactions are a strong function of the frequency spacing between them – having very significant implications on interpretation of linear stability or instability of modes from experimental data. Frequency spacing between the modes particularly influences the stability and existence of potential limit cycle solutions. In this paper, we extend earlier deterministic studies to include the effects of noise, studying how deterministic dynamics change with the addition of noise and the simultaneous impact of frequency spacing (i.e., closely, or widely spaced). Specifically, this paper characterizes three key effects of noise, which are (1) distribution of limit cycle amplitudes (“diffusion”), (2) shift in the average limit cycle amplitudes (“noise induced drift”), and (3) introduction of new bifurcations that are not present in the deterministic system. Key conclusions from this work are that in highly noisy practical environments, a deterministic/ low noise analysis will not be sufficient to explain even critical qualitative features of the system – such as existence of stable limit cycles or their amplitudes. Furthermore, the nature of noise-induced effects on nonlinear modal interactions can be fundamentally different for degenerate, closely spaced, and widely spaced modes.

42 ENGINEERING↗
DOE OSTI2021

Intramedullary Unicortical Button and All-Suture Anchors Provide Similar Maximum Strength for Onlay Distal Biceps Tendon Repair

To evaluate the biomechanical profile of onlay distal biceps repair with an intramedullary unicortical button versus all-suture anchors under cyclic loading and maximal load to failure. Twenty paired fresh-frozen human cadaveric elbows were randomized to onlay distal biceps repair with either a single intramedullary button or with two 1.35-mm all-suture anchors. A 1.3-mm high tensile strength tape was used in a Krackow stitch to suture the tendons in both groups. Specimens and repair constructs were loaded for 3,000 cycles and then loaded to failure. Maximum load to failure, mode of failure, and construct elongation were recorded. Mean (± standard deviation) maximum load to failure for the unicortical intramedullary button and all-suture anchor repairs were 503.23 ± 141.77 N and 537.33 ± 262.13 N (P = .696), respectively. Mean maximum displacement after 3,000 cycles (± standard deviation) was 4.17 ± 2.05 mm in the button group and 2.06 ± 1.05 mm in the suture anchor group (P = .014). Mode of failure in the button group was suture tape rupture in 7 specimens, failure at the tendon–suture interface in 2 specimens, and button pullout in 1 specimen. Anchor pullout was the mode of failure in all suture anchor specimens. There were no tendon ruptures or radial tuberosity fractures in either group. In conclusion, this study demonstrates that onlay distal biceps repair with 2 all-suture anchors has similar maximum strength to repair with an intramedullary button and that both are viable options for fixation.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

Perspective—Potential Benefit of Li-Rich Cathode Materials: Reduction of Co and Ni Content Rather than Achievement of Ultra-High Capacities

In the conventional cycling protocol for lithium and manganese rich NMC layered oxides (LMRNMC), the upper cutoff voltage V cut is extended to ~ 4.8, to achieve capacities of similar to 250 mAh g -1 . With this mode of operation, structural rearrangements result in voltage fade upon cycling. Herein, a strategy is proposed to avoid these structural rearrangements based on (a) restricting V cut to values < ~ 4.6 to shut down the bulk instabilities, and (b) application of a (preferably) semi-coherent coating that protects the surface oxygen. The potential benefit of this strategy would be to minimize Co and Ni content, compared to Ni-rich NMC.

25 ENERGY STORAGE↗
DOE OSTI2023

Diurnal cycle of precipitation over the tropics and central United States: intercomparison of general circulation models

Diurnal precipitation is a fundamental mode of variability that climate models have difficulty in accurately simulating. Here, in this work, the diurnal cycle of precipitation (DCP) in participating climate models from the Global Energy and Water Exchanges' DCP project is evaluated over the tropics and central United States. Common model biases such as excessive precipitation over the tropics, too frequent light-to-moderate rain, and the failure to capture propagating convection in the central United States still exist. Over the central United States, the issues of too weak rainfall intensity in climate runs is well improved in their hindcast runs with initial conditions from numerical weather prediction analyses. But the improvement is minimal over the central Amazon. Incorporating the role of the large-scale environment in convective triggering processes helps resolve the phase-locking issue in many models where precipitation often incorrectly peaks near noon due to maximum insolation over land. Allowing air parcels to be lifted above the boundary layer improves the simulation of nocturnal precipitation which is often associated with the propagation of mesoscale systems. Including convective memory in cumulus parameterizations acts to suppress light-to-moderate rain and promote intense rainfall; however, it also weakens the diurnal variability. Simply increasing model resolution (with cumulus parameterizations still used) cannot fully resolve the biases of low-resolution climate models in DCP. The hierarchy modeling framework from this study is useful for identifying the missing physics in models and testing new development of model convective processes over different convective regimes.

58 GEOSCIENCES↗
DOE OSTI2024

The importance of cycle-by-cycle data in performing rapid battery technology development and validation

Lithium-ion battery (LiB) technology is playing a crucial role in transforming the predominantly fossil fuel-based transportation and stationary storage sectors to achieve a low-carbon economy. Rapid innovation in the LiB materials to electrode to cell design is happening to satisfy the performance, life, and safety metrics required by those myriads of applications. Lately, advanced analytics, such as machine-learning or artificial intelligence (ML/AI) techniques, are being used more frequently to aid in expedited LiB technology development, performance validation, and life prediction. The success of these techniques often relies on a large volume of well-defined and high-quality battery test data. On the other hand, most battery developers and research and development (R&D) communities are still following a classical approach to develop batteries, which is running calendar- and/or cycle-aging tests, performing reference performance tests (RPTs), and conducting post-mortem analyses periodically without paying attention to the wealth of data often not collected during the calendar or cycle life aging tests. This sparse data collection approach is time- and resource-intensive, requiring data capture and evaluation of months to years of RPT data to diagnose accurate battery state of performance, health, and safety. Even so, the underlying aging modes and mechanisms can be missed. If collected properly, battery test data during cycling or calendaring can be efficiently combined with ML/AI techniques to create powerful tools in the rapid diagnosis of battery state of performance, health, and safety along with insights into underlying aging modes and mechanisms. In this report, we discuss the importance of effective cycle-by-cycle (CBC) data collection with example case studies. Within a reasonable timeframe, RPT data are often inadequate in capturing many of the crucial battery aging dynamics, which often predominantly show up in CBC test data. Finally, we also show examples of ML/AI techniques that use CBC data in rapid diagnosis and projection of LiB state of health (SOH) to motivate the scientific community in collecting and using CBC data to facilitate expeditious technology development and validation.

25 ENERGY STORAGE↗
DOE OSTI2021

Redox-stable symmetrical solid oxide fuel cells with exceptionally high performance enabled by electrode/electrolyte diffuse interface

Here, in this study, we report a high performance and redox-stable symmetrical solid oxide fuel cell (SOFC) based on (Ba 0.5 Sr 0.5 ) (Mo 0.1 Fe 0.9 )O 3-δ (BSMF) electrode and La 0.8 Sr 0.2 Ga 0.8 Mg 0.2 O 3-δ (LSGM) electrolyte. BSMF is able to operate both as anode and cathode. Excellent electrocatalytic activity has been achieved on BSMF towards hydrogen oxidation and oxygen reduction. Due to its closely matched lattice parameter to LSGM electrolyte, a unique diffuse interface is formed between BSMF and LSGM. Compared to a clean interface, e.g. BSMF/gadolinium doped ceria interface, this diffuse interface promotes the performance of BSMF electrode 1–1.8 times in 600–800 °C. Polarization resistance of the BSMF/LSGM specimen is as low as 0.047 and 0.007 Ωcm 2 in humidified H 2 and in air at 800 °C, respectively. On the BSMF/LSGM/BSMF symmetrical cell, a maximum power density of 2.28 W/cm 2 is achieved at 800 °C, the highest among with redox-stable ceramic electrodes to the best of our knowledge. Redox stability of this cell is confirmed. The role of anode and cathode is reversed back and forth in different operation modes. No apparent degradation is observed through 4 cycles within a 110 h operation period. These findings demonstrate that (Ba 0.5 Sr 0.5 ) (M o0.1 Fe 0.9 )O 3-δ coupled with LSGM electrolyte is an excellent choice to build a high performance, redox-stable SOFC.

25 ENERGY STORAGE↗
DOE OSTI2024

A novel polymeric lithicone coating for superior lithium metal anodes

Lithium metal (Li) is commonly regarded as the “holy grail” of rechargeable batteries and can serve as anodes for constituting various high-energy lithium metal batteries (LMBs). However, it suffers from two notorious issues: (1) continuous formation of inhomogeneous solid electrolyte interphase and (2) Li dendritic growth. Here, in this study, we developed a novel polymeric lithicone via a new molecular layer deposition (MLD) process, using lithium tert-butoxide (LTB) and hydroquinone (HQ) as precursors. We revealed that such an MLD process enabled the resultant LiHQ to grow linearly in a highly controllable and cyclic mode at a growth rate of 4 Å cycle −1 . Furthermore, its low process deposition temperature of 150 °C made it possible to practice high-quality coatings over Li anodes directly. We demonstrated that, very compellingly, this LiHQ coating could protect Li anodes from corrosion and dendritic growth. As a consequence, this LiHQ coating has enabled Li||Li symmetric cells an extremely long cyclability up to 8000 Li-plating/stripping cycles without failure. More excitingly, we demonstrated that, coupled with LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) cathodes, the LiHQ-modified Li anodes could help the resultant Li||NMC811 realize a much better capacity retention and much longer cyclability. Thus, this study represents a strategic route for developing commercializeable LMBs.

25 ENERGY STORAGE↗
DOE OSTI2021

Elevated Inlet Temperature Effects on the Operation of a Rotating Detonation Combustor

This experimental work explores the impact of elevated inlet temperatures on a H2/air operated rotating detonation combustor (RDC) without a nozzle. In practical systems, the temperature of the inlet air would be higher than that found in many laboratory settings. Inlet air pre-heating up to 480 K was accomplished by using an integrated pebble-bed heater. The operation of the RDC was found to switch from a single detonation wave at ambient temperature to two, counter-rotating detonation waves at higher temperatures for some of the conditions tested. In addition, the detonation wave properties (i.e., speed and pressure ratio) were impacted by the elevated inlet temperature. The cause of the observed changes in the operation dynamics was explored by evaluating the existence of secondary waves prior to the operational mode change and the changes in the cycle-averaged inlet Mach number.

Feleo, Alexander↗