Search NASA⌕ Search

SEARCH · Search NASA

Results for “module efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

An International Round-Robin Study on Thermoelectric Module Testing and Development of Standard Power Generation Modules

An international round-robin study on thermoelectric power generation modules was conducted with nine participating laboratories. Two types of commercially available bismuth telluride modules, 30 mm × 30 mm and 40 mm × 40 mm, were used. A test protocol was followed with five temperature set points from 50°C to 150°C. Graphite sheets were used as thermal interface materials with test pressure at 100 psi (0.69 MPa). The results showed large lab-to-lab variations and the key source of uncertainty for module efficiency was identified as the heat flux measurement. In the meantime, significant uncertainty was also found in maximum electrical power (P max ) measurements. As a result of the round-robin, a “standard module” with 4 × 4 legs on a 20 mm × 20 mm platform was suggested. A skutterudite module and a half-Heusler module were produced with identical geometry and 4 mm × 4 mm × 8 mm legs. All transport properties to calculate the figure-of-merit, zT, were measured from ambient temperature to 500°C. Module performance was measured by two laboratories. Two finite-element-analysis (FEA)-based models were developed independently to simulate and predict the module performance. In conclusion, the standard modules eliminated significant test uncertainties and are aimed at assisting device design and achieving more accurate performance predictions.

Round-robin↗

Tracking the Sun: Pricing and Design Trends for Distributed Photovoltaic Systems in the United States, 2024 Edition [Slides]

Berkeley Lab’s annual Tracking the Sun report describes trends among grid-connected, distributed solar photovoltaic (PV) and paired PV+storage systems in the United States. For the purpose of this report, distributed solar includes residential systems, roof-mounted non-residential systems, and ground-mounted systems up to 5 MW-AC. Ground-mounted systems larger than 5 MW-AC are covered in Berkeley Lab’s companion annual report, Utility-Scale Solar. The latest edition of the report is based on 3.7 million systems installed through year-end 2023, representing close to 80% of systems installed to date. The report describes and discusses key trends related to: -Project characteristics, including system size, module efficiencies, roof-coverage ratios, prevalence of paired PV with storage, use of module-level power electronics, third-party ownership, mounting configurations, panel orientation, and customer segmentation -Median installed-price trends, both nationally and by state -Variability in pricing according to system size, state, installer, equipment type, and other factors, relying on both descriptive analysis and a multi-variate regression to estimate the effects of key pricing drivers for residential systems installed in 2023.

14 SOLAR ENERGY↗

Analysis of the Value Proposition of High-Efficiency, Multijunction Solar Modules for Residential Rooftop Installations

Utilizing detailed bottom-up models, we analyze the potential markets for high-efficiency photovoltaic modules in the United States. We first estimate the fraction of area-constrained residential rooftops that could benefit from increasing the availability of high-efficiency systems. We then model the impact of efficiency on installed system costs in these area-constrained scenarios. Finally, we explore the value proposition of high-efficiency, fixed-tilt micro-concentrator photovoltaic modules in a series of case studies of residential customers, modeling the levelized cost of energy, payback period, and annual bill savings. We find that efficiency can provide significant savings in installed system cost and improve value to the solar system owner. The improvement in value depends on location and the size of the rooftop, as well as the ability of a given technology to collect diffuse light and achieve low module costs.

14 SOLAR ENERGY↗

High-speed modulator with interleaved junctions in zero-change CMOS photonics

A microring depletion modulator is demonstrated with T-shaped lateral p-n junctions used to realize efficient modulation while maximizing the RC limited bandwidth. The device having a 3 dB bandwidth of 13 GHz has been fabricated in a standard 45 nm microelectronics CMOS process. The cavity has a linewidth of 17 GHz and an average wavelength-shift of 9 pm/V in reverse-bias conditions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Highly efficient passive Q switches for a neodymium laser based on thiopyrylotricarbocyanine dyes

The spectral, photochemical and nonlinear optical properties of a group of thiopyrylotricarbocyanine dyes in a polyurethane matrix are studied and compared with well-known materials for passive Q-switching such as nickel BDN and BDNII complexes. Passive laser Q switches based on these dyes feature the high modulation efficiency (up to 76%) in neodymium lasers and high photochemical stability. It is shown that the service life of Q switches can be considerably increased by removing oxygen from a polymer matrix. (elements of laser setups)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Progress and Challenges in Absorber and Interface Fabrication of Polycrystalline CdTe Photovoltaics

Polycrystalline thin-film CdTe device efficiency of over 19% has been achieved at Colorado State University using a highly repeatable and scalable sublimation process. Record efficiency for research scale CdTe photovoltaics has been reported to be over 22% and highest reported module efficiency is over 18% by First Solar Inc. Use of Se alloying with CdTe to form a lower band-gap CdSexTe1-x (CST) alloy has led to higher devices efficiencies with better current collection. Recent materials characterization has revealed that Se may be responsible for more than just reduction of band-gap. With CdCl2 treatment Cl is known to very effectively passivate defects at CdTe grain boundaries. Recent materials and electrical characterization have shown that Se has a very similar behavior to Cl at the grain boundaries of polycrystalline CdTe. These include Se decorating the grain boundaries like Cl in the diffusion region between CST and CdTe while cross-section cathodoluminescence maps show substantially higher signal intensity in regions with Se. Double heterostructures fabricated using CdSeTe with Al2O3 as a passivating oxide have been measured to have several hundred nanosecond bulk recombination lifetime. These films were also measured to have surface recombination velocity of under 100 cm/s. These results among others emphasis that Se also helps in passivation of grain boundaries. High absorber quality may help in mitigating the voltage deficit that has traditionally been the largest limiting factor in CdTe photovoltaics in achieving efficiency closer to Shockley-Queisser limit. In addition to graded absorber devices and double heterostructures, replacing the traditional Cu doping with more advanced group V doping is an important research effort that maybe critical for future improvements in device efficiency. Nitrogen, Phosphorous, Arsenic and Antimony doping has been investigated by several research groups. Advanced co-sublimation hardware developed at Colorado State University provides researchers with a unique capability of depositing films for group V doping with Cd overpressure. Such deposition under Cd overpressure causes formation of CdV which is known to be favorable for incorporation of group V dopant and activation. Utilizing the high absorber and interface quality material and higher doping, efforts are in progress to fabricate polycrystalline devices with open-circuit voltage over 1V and device efficiency over 24%.

Munshi, Amit↗

Low-Power Absorption Saturation in Semiconductor Metasurfaces

Saturable optical elements lie at the cornerstone of many modern optical systems. Regularly patterned quasi-planar nanostructures—metasurfaces—are known to facilitate nonlinear optical processes. Such subwavelength semiconductor nanostructures can potentially serve as saturable components. In this work, we report on the intensity-dependent reflectance of femtosecond laser pulses from semiconductor metasurfaces with Mie-type modes, caused by the absorption saturation. Moreover, arrays of GaAs nanocylinders with magnetic dipole resonances in the spectral vicinity of the GaAs bandgap demonstrate a reduced saturation intensity and increased self-modulation efficiency, an order of magnitude higher than bulk GaAs or unstructured GaAs films. By contrast, the reflection modulation is shown to be negligible in the CW regime for the same average intensities, indicating that the process is not the result of temperature effects. Our work provides a novel idea for low-power saturable elements based on nonthermal nature of saturation. We conclude by devising a high-quality metasurface that can be used, in theory, to further reduce the saturation fluence below 50 nJ/cm 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Internal Compound Parabolic Concentrator (ICPC): a Novel Low Cost Solar Thermal Collection System for Desalination Processes

The research team at UC Merced designed, prototyped, and tested (1) a novel low cost non-tracking solar thermal collector/concentrator called the Integrated Compound Parabolic Concentrator (ICPC) and (2) a low-cost phase-change thermal energy storage system. Together these technologies can significantly reduce the levelized cost of heat from solar thermal sources while also incorporating features of dispatchability and portability. The ICPC allows elevated temperature and efficiency in a low cost, non-tracking collector. The collector has demonstrated 60% ±4% solar to thermal modules efficiency at fluid outlet temperature of 120°C. The raw material cost of the collector system is reduced by utilizing low cost aluminum minichannels. The collector design is also amenable to economic mass production. A 200 tube, 10 kW prototype array was constructed and tested, yielding over 6 kWh/day on average at outlet fluid temperature exceeding 120°C.

14 SOLAR ENERGY↗

A non-uniform three-gap buncher cavity with suppression of transverse-electromagnetic mode leakage in the triaxial klystron amplifier

The triaxial klystron amplifier is an efficient high power relativistic klystron amplifier operating at high frequencies due to its coaxial structure with large radius. However, the coaxial structures result in coupling problems among the cavities as the TEM mode is not cut-off in the coaxial tube. Therefore, the suppression of the TEM mode leakage, especially the leakage from the buncher cavity to the input cavity, is crucial in the design of a triaxial klystron amplifier. In this paper, a non-uniform three-gap buncher cavity is proposed to suppress the TEM mode leakage. The cold cavity analysis shows that the non-uniform three-gap buncher cavity can significantly suppress the TEM mode generation compared to a uniform three-gap buncher cavity. Particle-in-cell simulation shows that the power leakage to the input cavity is less than 1.5‰ of the negative power in the buncher cavity and the buncher cavity can efficiently modulate an intense relativistic electron beam free of self-oscillations. A fundamental current modulation depth of 117% is achieved by employing the proposed non-uniform buncher cavity into an X-band triaxial amplifier, which results in the high efficiency generation of high power microwave.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Cost and Reliability Improvement for CIGS-Based PV on Flexible Substrate: May 24, 2006 -- July 31, 2010

Global Solar Energy rapidly advances the cost and performance of commercial thin-film CIGS products using roll-to-roll processing on steel foil substrate in compact, low cost deposition equipment, with in-situ sensors for real-time intelligent process control. Substantial increases in power module efficiency, which now exceed 13%, are evident at GSE factories in two countries with a combinedcapacity greater than 75 MW. During 2009 the average efficiency of cell strings (3780 cm2) was increased from 7% to over 11%, with champion results exceeding 13% Continued testing of module reliability in rigid product has reaffirmed extended life expectancy for standard glass product, and has qualified additional lower-cost methods and materials. Expected lifetime for PV in flexible packagescontinues to increase as failure mechanisms are elucidated, and resolved by better methods and materials. Cost reduction has been achieved through better materials utilization, enhanced vendor and material qualification and selection. The largest cost gains have come as a result of higher cell conversion efficiency and yields, higher processing rates, greater automation and improved control inall process steps. These improvements are integral to this thin film PV partnership program, and all realized with the 'Gen2' manufacturing plants, processes and equipment.

14 SOLAR ENERGY↗

Characterization of an active metasurface using terahertz ellipsometry

Switchable metasurfaces fabricated on a doped epi-layer have become an important platform for developing techniques to control terahertz (THz) radiation, as a DC bias can modulate the transmission characteristics of the metasurface. To model and understand this performance in new device configurations accurately, a quantitative understanding of the bias-dependent surface characteristics is required. In this work, we perform THz variable angle spectroscopic ellipsometry on a switchable metasurface as a function of DC bias. By comparing these data with numerical simulations, we extract a model for the response of the metasurface at any bias value. Using this model, we predict a giant bias-induced phase modulation in a guided wave configuration. Lastly, these predictions are in qualitative agreement with our measurements, offering a route to efficient modulation of THz signals.

36 MATERIALS SCIENCE↗

Fast External Quantum Efficiency Measurements of Photovoltaic Modules

The external quantum efficiency (EQE) or associated spectral response is widely used to evaluate the performance of photovoltaics, light emitting diodes, photodetectors, photodiodes, semiconductor lasers, laser-induced refrigeration of solids etc. For photovoltaic (PV) devices, The EQE is used to determine the spectral mismatch correction that is used to convert a performance measurement from a non-ideal simulator spectrum to a standard spectrum in PV device calibrations. Moreover, EQE can provide important insight into the physics of a PV device. For instance, the EQE shape can be used to infer mechanisms limiting the performance of the device. However, EQE measurements of full-size PV modules remain a challenge in the PV community due to rare availability of reliable module QE measurement tools worldwide and the size and complexity of module architecture that comprises several cells connected in strings (series or/and parallel). Here, we use a customized nondestructive tool made of high-power light emitting diodes to perform high-throughput EQE measurements on PV modules. Circuit simulations show that the measurement system can safely be used to measure both crystalline silicon and thin film-based PV modules with series connected cells without the risk of damage through reverse bias. In addition, EQE mapping combined with electroluminescence show a strong correlation and provide a way to determine both spatial non-uniformity of the spectral response and defects/degradation effects across the module.

PV module↗

Enabling Efficiencies > 22.5% with Metal Oxide Passivating Contacts using Low-Cost Spatial Atomic Layer Deposition (Final Technical Report)

In this project, the University of Central Florida (UCF) worked to both increase module efficiency and reduce manufacturing cost by driving demonstrated lab-scale passivating contact technology using materials and processes compatible with high-volume manufacturing for crystalline silicon (c-Si) photovoltaic (PV) cells. Passivating contacts have garnered significant attention in recent years. They provide a means of suppressing contact recombination, a loss mechanism that limits the performance of industrially relevant cell architectures like Al back surface field (Al-BSF) cells and passivated emitter and rear cells (PERC). Most of the development of passivating contact technology has focused on the use of doped amorphous silicon or doped polysilicon contacts, but both suffer from parasitic optical absorption amongst other issues. Our team developed fully transparent hole-selective heterojunctions, deposited using atomic layer deposition (ALD), and showed how they could be incorporated into c-Si PV cells. The team conducted experiments to understand the process-structure-property relationship of hole-selective oxides, surface passivation oxide materials, and transparent conductive oxides deposited by ALD, and use that understanding to reduce contact recombination, contact resistivity, and parasitic optical absorption within c-Si PV cells. Before getting into the details of the report, we would like to note that COVID-19 has made it more challenging to conduct experimental research at UCF. UCF has a number of mandatory policies in place to ensure social distancing, testing, and contact tracing are all carried out in day-to-day operations. Despite these challenges, we worked diligently to make progress on this project in a manner that was as safe as possible. Over the course of the project, the UCF team and its collaborators have made the following discoveries and developments.

14 SOLAR ENERGY↗

Evaluating the causes of photovoltaics cost reduction: Why is PV different?

The goals of this project were to quantify sources of cost reduction in photovoltaics (PV), improve theories of technological evolution, develop new analytical methods, and formu- late guidelines for continued cost reduction in photovoltaics. A number of explanations have been suggested for why photovoltaics have come down in cost rapidly over time, including increased production rates, significant R&D expenditures, heavy patenting ac- tivity, decreasing material and input costs, scale economies, reduced plant construction costs, and higher conversion efficiencies. We classified these proposed causes into low- level factors and high-level drivers. Low-level factors include technical characteristics, such as module efficiency or wafer area, which are easily posed in terms of variables of a cost equation. High-level factors include scale economies, research and development (R&D), and learning-by-doing.

14 SOLAR ENERGY↗

Estimating Ultraviolet Radiation From Global Horizontal Irradiance

Terrestrial ultraviolet radiation (UV) radiation is a primary factor contributing to the degradation of photovoltaic (PV) modules' efficiency and reliability over time. Therefore, accurate knowledge of terrestrial UV incident on the surface of the PV materials is essential to understand the degradation of PV modules and provide reliable assessment of their service life. As PV is deployed in various climate zones, it is crucial that terrestrial UV information is available at various locations. However, the availability of terrestrial UV data - measured or modeled - is extremely limited. On the other hand, total solar irradiance (TS) datasets are relatively abundant. In this study, the National Renewable Energy Laboratory, its industry partners, and ASTM's International Subcommittee on Radiometry and Service Life Prediction are developing a simple method to estimate the clear-sky terrestrial UV irradiance (280-400 nm, 295-400 nm, 285-385 nm, or 295-385 nm) from total irradiance data (280-4000 nm). The goal is to provide reliable estimates of the UV received by samples as a function of location, orientation, tilt, and airmass, thus encompassing a variety of conditions. Here, the Simple Model of the Atmospheric Radiative Transfer of Sunshine (SMARTS) model is used to estimate the UV:TS ratio under various scenarios, and examines the influences of atmospheric constituents, such as aerosols, precipitable water vapor or ozone, and of the local surface characteristics (albedo), on the predicted UV.

14 SOLAR ENERGY↗

Estimating the Effects of Module Area on Thin-Film Photovoltaic System Costs

We investigate the potential effects of module area on the cost and performance of photovoltaic systems. Applying a bottom-up methodology, we analyzed the costs associated with thin-film modules and systems as a function of module area. We calculate a potential for savings of up to 0.10/Wand0.13/W in module manufacturing costs for CdTe and CIGS respectively, with large area modules. We also find that an additional 0.04/W savings in balance-of-systems costs may be achieved. Sensitivity of the /W cost savings to module efficiency, manufacturing yield, and other parameters is presented. Lifetime energy yield must also be maintained to realize reductions in the levelized cost of energy; the effects of module size on energy yield for monolithic thin-film modules are not yet well understood. Finally, we discuss possible non-cost barriers to adoption of large area modules.

14 SOLAR ENERGY↗

Estimating the Effects of Module Area on Thin-Film Photovoltaic System Costs: Preprint

We investigate the potential effects of module area on the cost and performance of photovoltaic systems. Applying a bottom-up methodology, we analyzed the costs associated with thin-film modules and systems as a function of module area. We calculate a potential for savings of up to 0.10 dollars/W and 0.13 dollars/W in module manufacturing costs for CdTe and CIGS respectively, with large area modules. We also find that an additional 0.04 dollars/W savings in balance-of-systems costs may be achieved. Sensitivity of the dollar/W cost savings to module efficiency, manufacturing yield, and other parameters is presented. Lifetime energy yield must also be maintained to realize reductions in the levelized cost of energy; the effects of module size on energy yield for monolithic thin-film modules are not yet well understood. Finally, we discuss possible non-cost barriers to adoption of large area modules.

14 SOLAR ENERGY↗

PV Fleet Performance Data Initiative Final Technical Report (FTR)

Improved analysis and reporting of photovoltaic (PV) field performance increases the certainty of owners and financiers that systems will perform as expected. Advanced module technologies (e.g., PERC, HJT, and bifacial) introduce new degradation mechanisms and performance characteristics. This project will leverage data from the ever-increasing PV fleet to develop models and understanding of the field performance of existing and new technologies. Please see our list of public reports at https://www.nrel.gov/pv/fleet-performance-data-initiative.html. Objective 1: Support the global PV industry with scalable, robust data analysis tools that reduce the uncertainty of PV system performance and loss calculation. Objective 2: Reduce perceived risk arising from degradation rate, soiling loss, and system availability by publishing detailed statistics on U.S. fleet performance. Objective 3: Highlight factors leading to system underperformance including module type, climate, mounting configuration, etc. Objective 4: Enable continued high system performance in modern PV systems, as turnover and advances in technology bring new suppliers and high-efficiency modules into the market.

14 SOLAR ENERGY↗