Search NASA⌕ Search

SEARCH · Search NASA

Results for “molecular ordering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Nanowire Thermoelectric Devices

Nanowire thermoelectric devices, now under development, are intended to take miniaturization a step beyond the prior state of the art to exploit the potential advantages afforded by shrinking some device features to approximately molecular dimensions (of the order of 10 nm). The development of nanowire-based thermoelectric devices could lead to novel power-generating, cooling, and sensing devices that operate at relatively low currents and high voltages. Recent work on the theory of thermoelectric devices has led to the expectation that the performance of such a device could be enhanced if the diameter of the wires could be reduced to a point where quantum confinement effects increase charge-carrier mobility (thereby increasing the Seebeck coefficient) and reduce thermal conductivity. In addition, even in the absence of these effects, the large aspect ratios (length of the order of tens of microns diameter of the order of tens of nanometers) of nanowires would be conducive to the maintenance of large temperature differences at small heat fluxes. The predicted net effect of reducing diameters to the order of tens of nanometers would be to increase its efficiency by a factor of .3. Nanowires made of thermoelectric materials and devices that comprise arrays of such nanowires can be fabricated by electrochemical growth of the thermoelectric materials in templates that contain suitably dimensioned pores (10 to 100 nm in diameter and 1 to 100 microns long). The nanowires can then be contacted in bundles to form devices that look similar to conventional thermoelectric devices, except that a production version may contain nearly a billion elements (wires) per square centimeter, instead of fewer than a hundred as in a conventional bulk thermoelectric device or fewer than 100,000 as in a microdevice. It is not yet possible to form contacts with individual nanowires. Therefore, in fabricating a nanowire thermoelectric device, one forms contacts on nanowires in bundles of the order of 10-microns wide. The fill factor for the cross-section of a typical bundle is about 1/2. Nanowires have been grown in alumina templates with pore diameters of 100 and 40 nm.

Borshchevsky, Alexander↗

Observing Planets and Small Bodies in Sputtered High Energy Atom (SHEA) Fluxes

The evolution of the surfaces of bodies unprotected by either strong magnetic fields or thick atmospheres in the Solar System is caused by various processes, induced by photons, energetic ions and micrometeoroids. Among these processes, the continuous bombardment of the solar wind or energetic magnetospheric ions onto the bodies may significantly affect their surfaces, with implications for their evolution. Ion precipitation produces neutral atom releases into the exosphere through ion sputtering, with velocity distribution extending well above the particle escape limits. We refer to this component of the surface ejecta as sputtered high-energy atoms (SHEA). The use of ion sputtering emission for studying the interaction of exposed bodies (EB) with ion environments is described here. Remote sensing in SHEA in the vicinity of EB can provide mapping of the bodies exposed to ion sputtering action with temporal and mass resolution. This paper speculates on the possibility of performing remote sensing of exposed bodies using SHEA The evolution of the surfaces of bodies unprotected by either strong magnetic fields or thick atmospheres in the Solar System is caused by various processes, induced by photons, energetic ions and micrometeoroids. Among these processes, the continuous bombardment of the solar wind or energetic magnetospheric ions onto the bodies may significantly affect their surfaces, with implications for their evolution. Ion precipitation produces neutral atom releases into the exosphere through ion sputtering, with velocity distribution extending well above the particle escape limits. We refer to this component of the surface ejecta as sputtered high-energy atoms (SHEA). The use of ion sputtering emission for studying the interaction of exposed bodies (EB) with ion environments is described here. Remote sensing in SHEA in the vicinity of EB can provide mapping of the bodies exposed to ion sputtering action with temporal and mass resolution. This paper speculates on the possibility of performing remote sensing of exposed bodies using SHEA and suggests the need for quantitative results from laboratory simulations and molecular physic modeling in order to understand SHEA data from planetary missions. In the Appendix, referenced computer simulations using existing sputtering data are reviewed.

Milillo, A.↗

Discretization Error Estimation and Control for Farfield Acoustic Signatures

We investigate the utility of adjoint-based error estimates for sonic boom farfield simulations governed by solutions of the augmented Burgers’ equation. Solution of this nonlinear system uses operator splitting with a second-order finite volume discretization in space and second-order Runge-Kutta time marching, while the absorption and molecular relaxation are solved using second-order central differencing. The discretization error in selected ground sonic boom cost functionals is estimated using the method of adjoint-weighted residuals. Key elements of the implementation process are emphasized with details provided on the practical aspects as appliedto the sonic boom farfield propagation. We establish the accuracy of the adjoint solutions usingcomplex step and finite difference approaches, and examine the accuracy of the error estimates using analytical N-wave solutions. We then apply it to a pressure waveform corresponding to the X-59 research aircraft. The investigations demonstrate that the method of adjoint-weighted residuals accurately predicts the level of discretization error present in sonic boom farfield simulations while offering insight into which features of the near field signal are the primary drivers of ground noise metrics. The numerical results indicate that at sampling frequencies as low as50kHz, discretization error in the propagation is under 0.01 dB[A] for realistically complex examples.

CST↗

Molecular clouds in starburst galaxy nuclei

New CO observations of a complete sample of starburst galaxies are presented in order to determine the range of molecular gas masses and star-formation efficiencies that characterize these systems. The properties of the galaxies in the sample are given, and the H-alpha and R-band CCD images for six of the galaxies are shown. The novel feature of this study is that the galaxies in this study are infrared selected as opposed to optically selected. They exhibit levels of nuclear star formation activity which are comparable to the starburst galaxies M82 and NGC 253. A subset of galaxies with unusually narrow CO line widths, high star-formation efficiencies, and compact 10-micron distributions is revealed. It is proposed that, if gas distributions in these galaxies are also compact, as the narrow linewidths suggest, the high yields of massive stars per unit mass of molecular gas may be attributed to a star-formation mechanism which becomes more efficient as the gas density increases.

Young, Judith S.↗

High Resolution Spectroscopy to Support Atmospheric Measurements

Spectroscopic parameters (such as line position, intensity, broadening and shifting coefficients and their temperature dependences, line mixing coefficients etc.) for various molecular species of atmospheric interest are determined. In order to achieve these results, infrared spectra of several molecular bands are obtained using high-resolution recording instruments such as tunable diode laser spectrometer and Fourier transform spectrometers. Using sophisticated analysis routines (Multispectrum nonlinear least squares technique) these high-resolution infrared spectra are processed to determine the various spectral line parameters that are cited above. Spectra were taken using the McMath-Pierce Fourier transform spectrometer (FTS) at the National Solar Observatory on Kitt Peak, Arizona as well as the Bruker FTS at the Pacific Northwest National Laboratory (PNNL) at Richland, Washington. Most of the spectra are acquired not only at room temperature, but also at several different cold temperatures. This procedure is necessary to study the variation of the spectral line parameters as a function of temperature in order to simulate the Earth's and other planetary atmospheric environments. Depending upon the strength or weakness of the various bands recorded and analyzed, the length(s) of the absorption cells in which the gas samples under study are kept varied from a few centimeters up to several meters and the sample temperatures varied from approximately +30 C to -63 C. Research on several infrared bands of various molecular species and their isotopomers are undertaken. Those studies are briefly described.

Venkataraman, Malathy Devi↗

Protobiological informatoin, bidirectional recognition and reverse translation

Emergence of protobiological information has been suggested by experiments in which heated mixtures of alpha-amino acids order themselves into a self limited array of thermal proteins. The polymers display selective catalytic, hormonal, and other activities. Interactions of varied cationic thermal proteins with polynucleotides indicate selective recognition in both directions. Reverse translation is partly a missing link in the molecular evolution flowsheet. The self ordering of amino acids serves conceptually as a deterministic evolutionary precursor of the modern coding mechanism. The possibility for the evolution of information at an early nontemplated protein stage is supported by findings of electrical signals from proteinoid microspheres prepared with no DNA/RNA in their history. The deposition of thermal copolyamino acids on lipid membranes in the Mueller-Rudin apparatus has here been found to produce electrical behavior like that evoked by bacterial EIM polypeptide. A new procedure is to make a film of membrane on the electrode; the results provide maximal repeatability. The principle of nonrandom biomacromolecular specificity identified by these studies in molecular evolution have been extrapolated to principles of evolution of advanced organisms.

Fox, S. W.↗

A Doubles Correction to Electronic Excited States from Configuration Interaction in the Space of Single Substitutions

A perturbative correction to the method of configuration interaction with single substitutions (CIS) is presented. This CIS(D) correction approximately introduces the effect of double substitutions which are absent in CIS excited states. CIS(D) is a second-order perturbation expansion of the coupled-cluster excited state method, restricted to single and double substitutions, in a series in which CIS is zeroth order, and the first-order correction vanishes. CIS (D) excitation energies are size consistent and the calculational complexity scales with the fifth power of molecular size, akin to second-order Moller-Plesset theory for the ground state. Calculations on singlet excited states of ethylene, formaldehyde, acetaldehyde, butadiene and benzene show that CIS (D) is a uniform improvement over CIS. CIS(D) appears to be a promising method for examining excited states of large molecules, where more accurate methods are not feasible.

Head-Gordon, Martin↗

Experimental dehydration of natural obsidian and estimation of DH2O at low water contents

Water diffusion experiments were carried out by dehydrating rhyolitic obsidian from Valles Caldera (New Mexico, USA) at 510-980 degrees C. The starting glass wafers contained approximately 0.114 wt% total water, lower than any glasses previously investigated for water diffusion. Weight loss due to dehydration was measured as a function of experiment duration, which permits determination of mean bulk water diffusivity, mean Dw. These diffusivities are in the range of 2.6 to 18 X 10(-14) m2/s and can be fit with the following Arrhenius equation: ln mean Dw (m2/s) = -(25.10 +/- 1.29) - (46,480 +/- 11,400) (J/mol) / RT, except for two replicate runs at 510 degrees C which give mean Dw values much lower than that defined by the above equation. When interpreted according to a model of water speciation in which molecular H2O is the diffusing species with concentration-independent diffusivity while OH units do not contribute to the transport but react to provide H2O, the data (except for the 510 degrees C data) are in agreement with extrapolation from previous results and hence extend the previous data base and provide a test of the applicability of the model to very low water contents. Mean bulk water diffusivities are about two orders of magnitude less than molecular H2O diffusivities because the fraction of molecular H2O out of total water is very small at 0.114 wt% total water and less. The 510 degrees C experimental results can be interpreted as due to slow kinetics of OH to H2O interconversion at low temperatures.

NASA Program Exobiology↗

Spectroscopic Diagnostics and an Arc Jet Heated Air Plasma

Spectral radiation measurements were made in the range of 200 to 900 nm across a section of the plenum of an arc jet wind tunnel using a series of optical fibers. The spectra contained line radiation from Oxygen and Nitrogen atoms and molecular radiation from N2(+), N2, and NO. Abel inversion technique is used to obtain radial distribution of the spectra. The analysis yielded radial profiles of the electronic excitation, vibrational and rotational temperatures of the flow field. Spectral fitting yielded branching ratios for different vibrational and rotational bands. Relatively mild flow conditions, i.e. enthalpy and mass flow rate, were used for prolonged measurements of up to and over two hours to establish the best experimental methods of temperature determinations. Signal to noise was improved by at least an order of magnitude enabling the molecular vibrational band heads of N2(+) (first negative system), N2 (second positive system), and NO (beta, gamma, delta, and epsilon systems) to be resolved in the lower ultraviolet wavelength regions. The increased signal to noise ratio also enabled partial resolution of the rotational lines of N2(+) and N2 in certain regions of minimal overlap. Comparison of the spectra with theoretical models such as the NEQAIR2 code are presented and show potential for fitting the spectra when reliable calibration is performed for the complete wavelength range.

Mack, Larry Howard, Jr.↗

A close-up view of the S87 molecular outflow

Observations of the S87 star-forming region have been made at optical, far-infrared, centimeter, and millimeter wavelengths in order to explain the origin of the previously discovered supersonic molecular gas in this source. S87/IRS 1 is a massive, pre-main-sequence object still embedded in its parent molecular cloud, but disrupting its surroundings through the action of its powerful stellar wind. The shocked wind gas provides the force required to accelerate the surrounding molecular gas to supersonic velocities. An ordered, large-scale magnetic field is postulated to set up an initially anisotropic pressure distribution which channels the flow into two oppositely directed lobes and provides some further acceleration to the already supersonic molecular gas. Only 5 percent of the molecular gas actually reaches escape velocity.

Barsony, M.↗

Effects of Atomic-Scale Structure on the Fracture Properties of Amorphous Carbon - Carbon Nanotube Composites

The fracture of carbon materials is a complex process, the understanding of which is critical to the development of next generation high performance materials. While quantum mechanical (QM) calculations are the most accurate way to model fracture, the fracture behavior of many carbon-based composite engineering materials, such as carbon nanotube (CNT) composites, is a multi-scale process that occurs on time and length scales beyond the practical limitations of QM methods. The Reax Force Field (ReaxFF) is capable of predicting mechanical properties involving strong deformation, bond breaking and bond formation in the classical molecular dynamics framework. This has been achieved by adding to the potential energy function a bond-order term that varies continuously with distance. The use of an empirical bond order potential, such as ReaxFF, enables the simulation of failure in molecular systems that are several orders of magnitude larger than would be possible in QM techniques. In this work, the fracture behavior of an amorphous carbon (AC) matrix reinforced with CNTs was modeled using molecular dynamics with the ReaxFF reactive forcefield. Care was taken to select the appropriate simulation parameters, which can be different from those required when using traditional fixed-bond force fields. The effect of CNT arrangement was investigated with three systems: a single-wall nanotube (SWNT) array, a multi-wall nanotube (MWNT) array, and a SWNT bundle system. For each arrangement, covalent bonds are added between the CNTs and AC, with crosslink fractions ranging from 0-25% of the interfacial CNT atoms. The SWNT and MWNT array systems represent ideal cases with evenly spaced CNTs; the SWNT bundle system represents a more realistic case because, in practice, van der Waals interactions lead to the agglomeration of CNTs into bundles. The simulation results will serve as guidance in setting experimental processing conditions to optimize the mechanical properties of CNT composites.

Jensen, Benjamin D.↗

Finite-field Calculations of Molecular Polarizabilities Using Field-Induced Polarization Functions: Second- and Third-order Perturbation Correlation Corrections to the Coupled Hartree-Fock Polarizability of H2O

Ordinary Rayleigh-Schroudinger perturbation theory with Moller-Plesset (RSMP) partitioning is used to calculate second- and third-order correlation corrections to the CHF polarizability and dipole moment of the water molecule by a finite-field procedure. Pade approximants are found to be useful in accelerating the convergence of the property perturbation expansions. Field-induced polarization functions suitable for polarizability calculations are determined. The average polarizability calculated, neglecting vibrational averaging, with Dunning's (9s5p/4s-4s2p/2s) contracted GTO basis set augmented by field-induced lslp2d/lp polarization functions is within 3 per cent of the experimental result. Correlation corrections to the dipole moment and polarizability of the water molecule calculated by the finite-field RSMP and single + double excitation CI(SDCI) methods for the same basis set are found to be in close agreement. The RSMP approach has the advantages of being size-consistent and of being capable of greater efficiency than the SCDI method. Comparative calculations carried out using Epstein-Nesbet partitioning show that through third order RSEN correlation perturbation expansions for the dipole moment and polarizability are less rapidly convergent than RSMP expansions. However, reasonable accord with RSMP results can be achieved by using Pade approximants to accelerate the convergence of RSEN energy perturbation expansions. The convergence of RSMP property correlation expansions based on the zeroth-order uncoupled-Hartree-Fock (UCHF) and coupled-Hartree-Fock (CHF) approximations are compared through third order. Whereas the CHF + RSMP expansions are for practical purposes fully converged, the UCHF + RSMP expansions are not adequately converged.

Langhoff, S. R.↗

Observations of CO isotopic emission and the far-infrared continuum of Centaurus A

Researchers present maps of the CO-12(1=0) line and the 100 micron and 50 micron far-infrared emission of Centaurus A, as well as measurements of the CO-12(2-1), CO-13(1-0), and the C-18O(1-0) lines at selected positions. The observations were taken with the Swedish-ESO Submillimeter Telescope (SEST) and the CPC instrument on board the Infrared Astronomy Satellite (IRAS). The millimeter data show that the bulk molecular material is closely associated with the dust lane and contained in a disk of about 180 seconds diameter and a total molecular mass of about 2 x 10 to the 8th power solar mass. The total molecular mass of the disk and bulge is of the order of 3 x 10 to the 8th power solar mass. The molecular gas in the nucleus is warm with a kinetic temperature of the order of 15 K and a number density of 10 to the 3rd power to 3 x 10 to the 4th power cm(-3). Absorption features in the CO-12 and CO-13 lines against the nuclear continuum emission indicate that the properties of giant molecular clouds are comparable to those of the Galaxy. The far-infrared data show that to a good approximation the dust temperature is constant across the dust lane at a value of about 42 K. The ratio between the far-infrared luminosity and the total molecular mass is 18 solar luminosity/solar mass and close to the mean value obtained for isolated galaxies. A comparison of the CO-12(1-0) and the far-infrared data indicates that a considerable amount of the far-infrared emission is not intimately associated with massive star formation.

Eckart, A.↗

Upper limits to the detection of ammonia from protoplanetary disks around HL Tauri and L1551-IRS 5

We present NH3(1, 1) and (2, 2) observations of the young stellar sources HL Tau and L1551-IRS 5 using the VLA in its B-configuration, which provides an angular resolution of about 0.4 arcsec (about 50 AU at 140 pc) at 1.3 cm wavelength. Our goal was to detect and resolve circumstellar molecular disks with radius of the order of 100 AU around these two sources. No ammonia emission was detected toward either of them. The 3-sigma levels were 2.7 mJy/beam and 3.9 mJy/beam for HL Tau and L1551-IRS 5, respectively, with a velocity resolution of about 5 km/s. With this nondetection, we estimate upper limits to the mass of the proposed protoplanetary molecular disks (within a radius of 10 AU from the central stars) on the order of 0.02/(X(NH3)/10 exp -8) solar mass for HL Tau and 0.1/(X(NH3)/10 exp -8) solar mass for L1551-IRS 5.

Gomez, Jose F.↗

Turbulent mixing of multiple co-axial gaseous fuel jets in a supersonic airstream

An experimental and analytical investigation of a strut-mounted, four-nozzle, downstream-facing, gaseous fuel-injector assembly was conducted in a Mach 4 airstream at 154 psia and 520 R. Helium was used as the injectant in order to simulate a low molecular weight fuel, and the interjet spacing (S/D) was the main parameter varied. The principal data are in the form of helium concentration profiles at seven axial stations, Mach number distributions at three axial stations, and Schlieren photographs of the flow field at different interjet spacings. An approximate analysis was developed based upon a linearization in the Von Mises plane, Crocco integrals for the temperature and concentrations fields, and an eddy viscosity model. Good agreement with the data was achieved. It was found that, at these conditions, interjet spacing has a significant effect on mixing only up to S/D of approximately 2.5, with the concentration of the injectant at a given point becoming smaller as S/D is increased.

Lorber, A. K.↗

Vibrational dependence of pressure induced spectral linewidths and line shifts - Application of the infinite order sudden scattering approximation

The infinite order sudden (IOS) approximation to molecular rotation is applied to simplify the theory of linewidths and shifts in vibration-rotation spectra. This approximation is expected to be most accurate for hard, short-range collisions and is therefore complementary to Anderson theory which is best for weak, glancing collisions. The IOS approximation predicts identical linewidths and shifts for P- and R-branch transitions with the same line number. It also predicts zero line shifts for pure rotational spectra. The dependence of linewidths and shifts on vibrational band is seen to be due mainly to variation in diagonal vibrational matrix elements of the intermolecular potential. Calculations are performed for the 0-0, 0-1, and 0-2 bands of CO perturbed by He, using a theoretical interaction potential with no semiempirical or adjustable parameters; results are in satisfactory accord with experimental data.

Green, S.↗

Recent progress on molecular hydrogen in Orion

The H2 emission from the Orion Molecular Cloud is, by an order of magnitude, the brightest known example of H2 emission, offering a means by which to estimate quantities connected with the mass flow. The size, temperature, velocity, and intensity of the lines can be used to infer the mass loss rate, the rate at which momentum is yielded to the cloud through masss loss, and the energy dissipation rate as the cloud is disrupted internally. Attention is accordingly given to the most recent observational results, with respect to morphology, extinction, level populations, and excitation temperature. The estimates concerning the mass loss phenomenon derived from H2 observations yield approximately the same numbers of those inferred from CO and H2O maser observations.

Beckwith, S.↗

Observations of molecular ions in the earth's magnetosphere

The retarding ion mass spectrometer on Dynamics Explorer 1 operating over the polar cap during a large magnetic storm has measured fluxes of up to 10 to the 6th ions/sq cm s of the molecular ions N2(+), NO(+), and O2(+). These ions were measured beginning low in the satellite orbit (1.1 earth radii) and extending to about 3 earth radii geocentric altitude. Near perigee, the ions have a rammed distribution indicating a cold Maxwellian plasma (1000-2000 K). The molecular ions gradually shift to a field-aligned distribution at the higher alitudes. An upward flow of 5-10 km/s is found in these field-aligned measurements. The density of the molecular ions is on the order of 2/cu cm at all altitudes, and the energy of the ions generally increases as the satellite moves sunward across the southern polar cap. Kinetic energies of at least 20 eV were found at 2.5 earth-radii geocentric distance.

Craven, P. D.↗