Search NASA⌕ Search

SEARCH · Search NASA

Results for “morphological stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Morphological instability in epitaxially strained dislocation-free solid films - Linear stability theory

The morphological instability of a growing epitaxially strained dislocation-free solid film is analyzed. An evolution equation for the film surface is derived in the dilute limit of vacancies based on surface diffusion driven by a stress-dependent chemical potential. From the time-dependent linear stability problem the conditions for which a growing film is unstable are determined. It is found that the instability is driven by the lattice mismatch between the film and the substrate; however, low temperatures as well as elastically stiff substrates are stabilizing influences. The results also reveal that the critical film thickness for instability depends on the growth rate of the film itself. Detailed comparison with experimental observations indicates that the instability described exhibits many of the observed features of the onset of the 'island instability'.

Spencer, B. J.↗
DOE OSTI2023

Dimer Acceptor Adopting a Flexible Linker for Efficient and Durable Organic Solar Cells

Abstract Organic solar cells (OSCs) have advanced rapidly due to the development of new photovoltaic materials. However, the long‐term stability of OSCs still poses a severe challenge for their commercial deployment. To address this issue, a dimer acceptor ( d T9TBO) with flexible linker is developed for incorporation into small‐molecule acceptors to form molecular alloy with enhanced intermolecular packing and suppressed molecular diffusion to stabilize active layer morphology. Consequently, the PM6 : Y6 : d T9TBO‐based device displays an improved power conversion efficiency (PCE) of 18.41 % with excellent thermal stability and negligible decay after being aged at 65 °C for 1800 h. Moreover, the PM6 : Y6 : d T9TBO‐based flexible OSC also exhibits excellent mechanical durability, maintaining 95 % of its initial PCE after being bended repetitively for 1500 cycles. This work provides a simple and effective way to fine‐tune the molecular packing with stabilized morphology to overcome the trade‐off between OSC efficiency and stability.

Chemistry↗
DOE OSTI2025

A quantitative imaging framework for lithium morphology: Linking deposition uniformity to cycle stability in lithium metal batteries

Characterizing the morphology of lithium (Li) is crucial for developing long-lasting lithium metal batteries. It is well established that more uniform Li deposition correlates with better cell performance. Li morphology is often characterized through qualitative analysis of scanning electron microscopy (SEM) images; however, there are no widely accepted metrics to quantitatively describe deposition uniformity. Here, we propose a framework to quantify uniformity through SEM image analysis via the index of dispersion (ID) metric, which is defined and presented in the context of Li metal batteries. We also explore experimental impacts of sampling protocols onIDmeasurements. Our results demonstrate that theIDmetric is highly sensitive to variations in deposition uniformity, including the coexistence and uniformity of multiple morphologies, uniformity within a single morphology, and particle size distribution uniformity. Furthermore, it is demonstrated that uniformity, as measured by theID, can be related to the average potential of Li||Li symmetric cells over cycling. Higher capacity cycling leads to more pronounced changes in bothIDand average cell potential. Local minima/maxima are found consistently in bothIDand average cell potential immediately before cells short-circuit, which we suggest may indicate a collapse of the microstructure prior to failure. We put forward this framework as a more robust approach to quantify Li deposition uniformity, advancing the development of Li metal batteries that are safer and longer lasting.

Science & Technology - Other Topics↗
DOE OSTI2025

MXene-Derived Potassium-Preintercalated Bilayered Vanadium Oxide Nanostructures for Cathodes in Nonaqueous K-Ion Batteries

Bilayered vanadium oxides (BVOs) are promising cathode materials for beyond-Li-ion batteries due to their tunable chemistries and high theoretical capacities. However, the large size of beyond-Li + ions limits electrochemical cycling and rate capability of BVO electrodes. Recent reports of MXene-derived BVOs with nanoscale flower-like morphology have shown improved electrochemical stability at high rates up to 5C in nonaqueous lithium-ion batteries. Here, we report how morphological stabilization can lead to improved rate capability in potassium-ion batteries (PIBs) through the synthesis and electrochemical characterization of MXene-derived K-preintercalated BVOs (MD-KVOs), which were derived from two V 2 CT x precursor materials prepared using two different etching protocols. We show that the etching conditions affect the surface chemistry of the MXene, which plays a role in the MXene-to-oxide transformation process. MXene derived from a milder etchant transformed into a nanoflower MD-KVO with two-dimensional (2D) nanosheet petals (KVO-DMAE) while a more aggressive etchant produced a MXene that transformed into a MD-KVO with one-dimensional (1D) nanorod morphology (KVO-CMAE). Electrochemical cycling of the produced MD-KVOs after drying at 200 °C under vacuum (KVO-DMAE-200 and KVO-CMAE-200) in PIBs showed that electrochemical stability of MD-KVO at high rates improved through the morphological stabilization of 2D particles combined with the control of interlayer water and K + ion content. Structure refinement of KVO-DMAE-200 further corroborates the behavior observed during K + ion cycling, connecting structural and compositional characteristics to the improved rate capability. This work demonstrates how proper synthetic methodology can cause downstream effects in the control of structure, chemical composition, and morphology of nanostructured layered oxide materials, which is necessary for development of future materials for beyond-Li-ion battery technologies.

25 ENERGY STORAGE↗
DOE OSTI2020

Efficient, Thermally Stable, and Mechanically Robust All-Polymer Solar Cells Consisting of the Same Benzodithiophene Unit-Based Polymer Acceptor and Donor with High Molecular Compatibility

All-polymer solar cells (all-PSCs) are a highly attractive class of photovoltaics for wearable and portable electronics due to their excellent morphological and mechanical stabilities. Recently, new types of polymer acceptors (P A s) consisting of non-fullerene small molecule acceptors (NFSMAs) with strong light absorption have been proposed to enhance the power conversion efficiency (PCE) of all-PSCs. However, polymerization of NFSMAs often reduces entropy of mixing in PSC blends and prevents the formation of intermixed blend domains required for efficient charge generation and morphological stability. One approach to increase compatibility in these systems is to design P A s that contain the same building blocks as their polymer donor (P D ) counterparts. Here, a series of NFSMA-based P A s [P(BDT2BOY5-X), (X = H, F, Cl)] are reported, by copolymerizing NFSMA (Y5-2BO) with benzodithiophene (BDT), a common donating unit in high-performance P D s such as PBDB-T. All-PSC blends composed of PBDB-T PD and P(BDT2BOY5-X) P A show enhanced molecular compatibility, resulting in excellent morphological and electronic properties. Specifically, PBDB-T:P(BDT2BOY5-Cl) all-PSC has a PCE of 11.12%, which is significantly higher than previous PBDB-T:Y5-2BO (7.02%) and PBDB-T:P(NDI2OD-T2) (6.00%) PSCs. Additionally, the increased compatibility of these all-PSCs greatly improves their thermal stability and mechanical robustness. For example, the crack onset strain (COS) and toughness of the PBDB-T:P(BDT2BOY5-Cl) blend are 15.9% and 3.24 MJ m -3 , respectively, in comparison to the PBDB-T:Y5-2BO blends at 2.21% and 0.32 MJ m -3 .

14 SOLAR ENERGY↗
DOE OSTI2025

The role of excess vacancies in stabilizing solute clusters in low-alloy steels

The formation of solute clusters in irradiated low-alloy steels, such as reactor pressure vessel steels, is a critical cause of radiation hardening and embrittlement. However, the chemical interactions among solute elements and excess vacancies remain to be fully understood. This study employs density functional theory, cluster expansion, and lattice-based Monte Carlo simulations to examine the stability and morphology of nano-size coherent solute clusters with excess vacancies. The findings reveal that excess vacancies are crucial in stabilizing and promoting the growth of Mn-Ni-Si-vacancy clusters. A minimum of seven vacancies is required for stable nucleation and growth of these clusters. These Mn-Ni-Si clusters act as defect sinks, effectively trapping and absorbing mobile vacancies generated under irradiation. Furthermore, phosphorus (P) preferentially dissolves in Mn-Ni-Si clusters due to chemical coupling with vacancies. In conclusion, this study offers new insights into solute-vacancy interactions, enhancing our understanding of solute-defect cluster formation and embrittlement in low-alloy steels.

36 - MATERIALS SCIENCE↗
DOE OSTI2023

Responsive blends of block copolymers stabilize the hexagonally perforated lamellae morphology

Blends of block copolymers can form phases and exhibit features distinct from the constituent materials. Herein we study thin film blends of cylinder-forming and lamellar-forming block copolymers across a range of substrate surface energies. Blend materials are responsive to interfacial energy, allowing selection of pure or coexisting phases based on surface chemistry. Blending stabilizes certain motifs that are typically metastable, and can be used to generate pure hexagonally perforated lamellar thin films across a range of film thicknesses and surface energies. This tolerant behavior is ascribed to the ability of blend materials to redistribute chains to stabilize otherwise high-energy defect structures. The blend responsiveness allows the morphology to be spatially defined through multi-tone chemical surface patterns.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2019

Surface Engineering by Simultaneous Action of Multiple External Fields (Final Technical Report)

This research project aims at enabling surface engineering strategies based on the fundamental understanding and predictive modeling of the surface morphological response of solid materials subjected to the combined action of multiple external forces. Surface morphological response to mismatch strain in strained-layer heterostructures also is analyzed. Our research focuses on the surface morphological evolution and stability of electrically conducting (metallic, such as Cu) and semiconducting (such as Si) solids under the simultaneous application of mechanical stresses, electric fields, and temperature gradients. We emphasize on identifying the conditions under which the multiply driven surface morphology is stable and on exploring the complexity of the corresponding various morphologically stable surface patterns. We also emphasize on the driven evolution of nanoscale features aiming at stabilizing and controlling nanoscale patterns on surfaces by their manipulation through simultaneously applied multiple external forces. Specifically, we address systematically the morphological response to the combined action of multiple external forces of bulk solid surfaces, surfaces of thin films grown epitaxially on thick or thin substrates, as well as nanoscale surface features such as coherently strained islands grown epitaxially on substrate surfaces. The research is based on a modeling approach that combines theoretical analyses of surface morphological stability with self-consistent dynamical simulations of surface evolution based on properly parameterized continuum and multiscale surface transport models.

36 MATERIALS SCIENCE↗
NASA NTRS2007

Multifunctional Composites for Improved Polyimide Thermal Stability

The layered morphology of silicate clay provides an effective barrier to oxidative degradation of the matrix resin. However, as resin thermal stability continues to reach higher limits, development of an organic modification with comparable temperature capabilities becomes a challenge. Typically, phyllosilicates used in polymer nanocomposites are modified with an alkyl ammonium ion. Such organic modifiers are not suited for incorporation into high temperature polymers as they commonly degrade below 200oC. Therefore, the development of nanoparticle specifically suited for high temperature applications is necessary. Several nanoparticles were investigated in this study, including pre-exfoliated synthetic clay, an organically modified clay, and carbon nanofiber. Dispersion of the layered silicate increases the onset temperature of matrix degradation as well as slows oxidative degradation. The thermally stable carbon nanofibers are also observed to significantly increase the resin thermal stability.

Miller, Sandi G.↗
DOE OSTI2021

A Morphologically Stable Li/Electrolyte Interface for All-Solid-State Batteries Enabled by 3D-Micropatterned Garnet

Morphological degradation at the Li/solid-state electrolyte (SSE) interface is a prevalent issue causing performance fading of all-solid-state batteries (ASSBs). To maintain the interfacial integrity, most ASSBs are operated under low current density with considerable stack pressure, which significantly limits their widespread usage. In this work, a novel 3D-micropatterned SSE (3D-SSE) that can stabilize the morphology of the Li/SSE interface even under relatively high current density and limited stack pressure is reported. Under the pressure of 1.0 MPa, the Li symmetric cell using a garnet-type 3D-SSE fabricated by laser machining shows a high critical current density of 0.7 mA cm –2 and stable cycling over 500 h under 0.5 mA cm –2 . This excellent performance is attributed to the reduced local current density and amplified mechanical stress at the Li/3D-SSE interface. These two effects can benefit the flux balance between Li stripping and creep at the interface, thereby pre-venting interfacial degradation such as void formation and dendrite growth.

3D-micropatterned garnet↗
DOE OSTI2022

Targeted Adjusting Molecular Arrangement in Organic Solar Cells via a Universal Solid Additive

The incorporation of solid additive has been considered as an effective strategy for developing organic photovoltaics with multi-components, which is independent of dynamics, playing unique roles in morphology adjustment. However, their complex working mechanisms involving specific chemical structures are selective to material systems, hence limiting their university and flexibility in application. Herein, an inert small-molecular compound naphtho[1,2-c:5,6-c′]bis[1,2,5]thiadiazole (NT) is introduced into the bulk-heterojunction blend as the solid additive, which can function with various material systems and solvents, depending on its simple π-conjugated structure and S⋯N interaction for adjusting molecular alignment. It is interesting to note that the introduced NT can not only improve device performance, but also simplify complicated pre- or post-processing methods, reduce impact from batch-to-batch differences, construct sufficient energy transfer channel as well as improve device stability. The resulting devices based on PTzBI-dF:Y6-BO system show an impressive power conversion efficiency of 17.4% with obviously enhanced T 80 lifetime of >1200 h. These findings provide useful guidelines for exploring potential universal solid additives benefitting toward commercial application.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Optimizing $\mathrm{ACRT}$ to reduce inclusion formation during the $\mathrm{VGF}$ growth of cadmium zinc telluride: II. Application to experiments

Here two different accelerated crucible rotation technique (ACRT) rotation schedules are assessed, via theoretical computations and growth experiments, according to their ability to reduce tellurium-rich inclusions during the vertical gradient freeze (VGF) of cadmium zinc telluride (CZT). A vigorous rotation schedule based on classical ACRT guidelines produces a well-mixed melt that is expected to reduce tellurium inclusions compared to growth without crucible rotation. In contrast, a new ACRT schedule, derived from model-based optimization for interface stability, employs slower rotation with longer periods and is predicted to further reduce inclusions. Growth experiments corroborate these expectations. Namely, both ACRT schedules result in crystals with inclusion size and volume significantly decreased from levels found in material grown with no rotation, and material grown using the computationally optimized ACRT parameters exhibits a median inclusion size that is smaller and with a sharper distribution than in material grown via classical ACRT.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Unveiling the Emergent Traits of Chiral Spin Textures in Magnetic Multilayers

Abstract Magnetic skyrmions are topologically wound nanoscale textures of spins whose ambient stability and electrical manipulation in multilayer films have led to an explosion of research activities. While past efforts focused predominantly on isolated skyrmions, recently ensembles of chiral spin textures, consisting of skyrmions and magnetic stripes, are shown to possess rich interactions with potential for device applications. However, several fundamental aspects of chiral spin texture phenomenology remain to be elucidated, including their domain wall (DW) structure, thermodynamic stability, and morphological transitions. Here the evolution of these textural characteristics are unveiled on a tunable multilayer platform—wherein chiral interactions governing spin texture energetics can be widely varied—using a combination of full‐field electron and soft X‐ray microscopies with numerical simulations. With increasing chiral interactions, the emergence of Néel helicity, followed by a marked reduction in domain compressibility, and finally a transformation in the skyrmion formation mechanism are demonstrated. Together with an analytical model, these experiments establish a comprehensive microscopic framework for investigating and tailoring chiral spin texture character in multilayer films.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enabling thermal energy storage in structural cementitious composites with a novel phase change material microcapsule featuring an inorganic shell and a bio-inspired silica coating

Phase change material (PCM) microcapsules offer a promising approach for integrating PCM into building materials for efficient thermal energy storage. Here, this study presents the development of a novel PCM microcapsule specifically designed for incorporation into cementitious materials. The microcapsule consists of a low-cost PCM core derived from vegetable oil by-products and a durable inorganic shell made from cenosphere, a hollow fly ash generated from coal burning power plants. A novel process is developed to apply a silica coating to these cenosphere-based PCM microcapsules (CPCM), resulting in bioinspired-silica-coated CPCM microcapsules (BCPCM). This coating process draws inspiration from marine microorganism-based silica production and utilizes low-cost sodium silicate as a precursor, enabling eco-friendly and cost-effective manufacturing at ambient temperature and mild pH conditions. The morphology, chemical stability, and thermal properties of the BCPCM along with its thermo-mechanical performance in cementitious composites were comprehensively analyzed. Experimental results demonstrate successful silica deposition on BCPCM, leading to enhanced latent heat properties of the produced BCPCM. With the silica coating, BCPCM exhibits a 50 °C delay in thermal decomposition compared to CPCM, enhancing fire resistance and preventing premature PCM leakage of the microcapsule. The bioinspired silica coating effectively restores over 10% of the strength loss for each percent increase in CPCM incorporated into the mortar. The thermal performance experiments reveal that increasing the BCPCM content reduces temperature peaks and rates of temperature increase, indicating an improved capacity for thermal energy storage. This new PCM microcapsule provides a cost-effective solution to integrate thermal energy storage to cementitious material, as evidenced that over 30% of aggregates (in volume) can be replaced by the microcapsule without a drastic loss of strength.

25 ENERGY STORAGE↗
DOE OSTI2021

The effects of ACRT on melt undercooling during the growth of CZT via the traveling heater method: Ekman versus Taylor-Görtler flows

For the first time, a comprehensive model for the traveling heater method, including detailed species transport and phase-change thermodynamics, is applied to understand the effects of accelerated crucible rotation (ACRT) on the growth of cadmium zinc telluride. Here, a rotation schedule that is designed from classical considerations does not completely mix the melt, rather undercooled regions of localized melt are swept periodically across the growth interface. Even without melt homogenization, these ACRT-driven flows disrupt the persistent undercooling that occurs during THM growth without rotation. An ACRT schedule designed to promote Ekman flows results in lower levels of melt undercooling than a schedule designed to promote Taylor-Görtler flows and greater mixing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Coupling computational thermodynamics with density-function-theory based calculations to design L12 precipitates in Fe Ni based alloys

Achieving a high-volume fraction of thermodynamically stable L12-type precipitates that are resistant to coarsening is of great importance for the development of low-cost FeNi based austenitic steels. With the aid of computational thermodynamics, this work designed two model alloys: Fe-37.4Ni-6.1Al-2.9Ti (FNAT) and Fe-45.2Ni-5.9Al-8.5Si (FNAS). Both alloys were designed to contain a similar amount of L1 2 precipitate in Fe-Ni matrix without forming other precipitates. Density-Function-Theory (DFT) calculation was coupled with computational thermodynamics to predict the critical radius at which the precipitates change shape from spherical to cuboidal. The calculation results suggest that critical radius for the FNAT alloy is about two orders of magnitude larger than that for the FeNiAlSi alloy. Phase stability and morphology of the L1 2 precipitates in these two alloys were experimentally investigated through X-ray diffraction, atom probe tomography, and scanning and transmission electron microscopy. The L1 2 precipitates in the FeNiAlSi system were found to be cuboidal and rod shaped, with much larger size than the spherical ones in the FeNiAlTi system, agreeing with the calculation results. This work suggested that coupling computational thermodynamics with DFT calculations can be reliably used to design L1 2 precipitates in FeNi based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Anion exchange membranes: The effect of reinforcement in water and electrolyte

Alkaline anion-conducting polymer-based CO 2 electrolysis and water electrolysis are among two emerging renewable energy conversion technologies. Their system design and integration offer promise of lower capital cost due to utilization of low-cost catalysts, in contrast to platinum group metal catalysts required for cation-conducting polymer-based devices. However, a critical component, the polymer electrolyte membrane, remains an obstacle hampering system performance and durability. In this study, commercially-available Sustainion® membranes with and without PTFE-reinforcement were investigated to understand previously unreported origins of improved device performance when compared to alternative membrane chemistries. We report critical membrane properties, such as morphology, thermal stability, as well as temperature-, hydration-, and counter-ion dependent ion conductivity. Moveover, the changes in uptake and conductivity of membranes in supporting electrolytes of K 2 CO 3 and KOH investigated as a function of their concentration. Presence of reinforcement and supporting electrolyte type alter the membrane's transport functionality, which could help guide device design for improved performance. In conclusion, the obtained results not only show how Sustainion® properties change with operating environment for CO 2 and water electrolysis applications, but also provide understanding for internal and external factors controlling anion-exhcnage membrane functionality in electrochemical devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Impact of Nanoparticle Size and Surface Chemistry on Peptoid Self-Assembly

Self-assembled organic nanomaterials can be generated by bottom-up assembly pathways where the structure is controlled by the organic sequence and altered using pH, temperature, and solvation. In contrast, self-assembled structures based on inorganic nanoparticles typically rely on physical packing and drying effects to achieve uniform superlattices. By combining these two chemistries to access inorganic–organic nanostructures, we aim to understand the key factors that govern the assembly pathway and structural outcomes in hybrid systems. In this work, we outline two assembly regimes between quantum dots (QDs) and reversibly binding peptoids. These regimes can be accessed by changing the solubility and size of the hybrid (peptoid-QD) monomer unit. The hybrid monomers are prepared via ligand exchange and assembled, and the resulting assemblies are studied using ex-situ transmission electron microscopy as a function of assembly time. In aqueous conditions, QDs were found to stabilize certain morphologies of peptoid intermediates and generate a final product consisting of multilayers of small peptoid sheets linked by QDs. The QDs were also seen to facilitate or inhibit assembly in organic solvents based on the relative hydrophobicity of the surface ligands, which ultimately dictated the solubility of the hybrid monomer unit. Increasing the size of the QDs led to large hybrid sheets with regions of highly ordered square-packed QDs. A second, smaller QD species can also be integrated to create binary hybrid lattices. Furthermore, these results create a set of design principles for controlling the structure and structural evolution of hybrid peptoid-QD assemblies and contribute to the predictive synthesis of complex hybrid matter.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗