SEARCH · Search NASA

Results for “motors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS2004

High Power Density Motors

With the growing concerns of global warming, the need for pollution-free vehicles is ever increasing. Pollution-free flight is one of NASA's goals for the 21" Century. , One method of approaching that goal is hydrogen-fueled aircraft that use fuel cells or turbo- generators to develop electric power that can drive electric motors that turn the aircraft's propulsive fans or propellers. Hydrogen fuel would likely be carried as a liquid, stored in tanks at its boiling point of 20.5 K (-422.5 F). Conventional electric motors, however, are far too heavy (for a given horsepower) to use on aircraft. Fortunately the liquid hydrogen fuel can provide essentially free refrigeration that can be used to cool the windings of motors before the hydrogen is used for fuel. Either High Temperature Superconductors (HTS) or high purity metals such as copper or aluminum may be used in the motor windings. Superconductors have essentially zero electrical resistance to steady current. The electrical resistance of high purity aluminum or copper near liquid hydrogen temperature can be l/lOO* or less of the room temperature resistance. These conductors could provide higher motor efficiency than normal room-temperature motors achieve. But much more importantly, these conductors can carry ten to a hundred times more current than copper conductors do in normal motors operating at room temperature. This is a consequence of the low electrical resistance and of good heat transfer coefficients in boiling LH2. Thus the conductors can produce higher magnetic field strengths and consequently higher motor torque and power. Designs, analysis and actual cryogenic motor tests show that such cryogenic motors could produce three or more times as much power per unit weight as turbine engines can, whereas conventional motors produce only 1/5 as much power per weight as turbine engines. This summer work has been done with Litz wire to maximize the current density. The current is limited by the amount of heat it generates. By increasing the heat transfer out of the wire, the wires can carry a larger current and therefore produce more force. This was done by increasing the surface area of the wire to allow more coolant to flow over it. Litz wire was used because it can carry high frequency current. It also can be deformed into configurations that would increase the surface area. The best configuration was determined by heat transfer and force plots that were generated using Maxwell 2D. Future work will be done by testing and measuring the thrust force produced by the wires in a magnetic field.

Kascak, Daniel J.↗

DOE OSTI2021

Global transcriptome profile of the developmental principles of in vitro iPSC-to-motor neuron differentiation

Abstract Background Human induced pluripotent stem cells (iPSC) have opened new avenues for regenerative medicine. Consequently, iPSC-derived motor neurons have emerged as potentially viable therapies for spinal cord injuries and neurodegenerative disorders including Amyotrophic Lateral Sclerosis. However, direct clinical application of iPSC bears in itself the risk of tumorigenesis and other unforeseeable genetic or epigenetic abnormalities. Results Employing RNA-seq technology, we identified and characterized gene regulatory networks triggered by in vitro chemical reprogramming of iPSC into cells with the molecular features of motor neurons (MNs) whose function in vivo is to innervate effector organs. We present meta-transcriptome signatures of 5 cell types: iPSCs, neural stem cells, motor neuron progenitors, early motor neurons, and mature motor neurons. In strict response to the chemical stimuli, along the MN differentiation axis we observed temporal downregulation of tumor growth factor-β signaling pathway and consistent activation of sonic hedgehog, Wnt/β-catenin, and Notch signaling. Together with gene networks defining neuronal differentiation (neurogenin 2, microtubule-associated protein 2, Pax6, and neuropilin-1), we observed steady accumulation of motor neuron-specific regulatory genes, including Islet-1 and homeobox protein HB9. Interestingly, transcriptome profiling of the differentiation process showed that Ca 2+ signaling through cAMP and LPC was downregulated during the conversion of the iPSC to neural stem cells and key regulatory gene activity of the pathway remained inhibited until later stages of motor neuron formation. Pathways shaping the neuronal development and function were well-represented in the early motor neuron cells including, neuroactive ligand-receptor interactions, axon guidance, and the cholinergic synapse formation. A notable hallmark of our in vitro motor neuron maturation in monoculture was the activation of genes encoding G-coupled muscarinic acetylcholine receptors and downregulation of the ionotropic nicotinic acetylcholine receptors expression. We observed the formation of functional neuronal networks as spontaneous oscillations in the extracellular action potentials recorded on multi-electrode array chip after 20 days of differentiation. Conclusions Detailed transcriptome profile of each developmental step from iPSC to motor neuron driven by chemical induction provides the guidelines to novel therapeutic approaches in the re-construction efforts of muscle innervation.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2026

New principles of self‐organization created through the interplay of DNA condensates, microtubules, and motors

Bioinspired design—which holds great promise for a new generation of materials that are robust to defects, scalable under green manufacture, environmentally responsive, and programmably reconfigurable—requires mastery over molecular self-organization. Yet, from its specific mechanisms to most general architectures, the principles governing self-organization remain poorly understood and not even fully enumerated. For living systems, one obvious architectural principle is the modular reuse of a few simple molecular components in myriad combinations to achieve more complex phenomena. For example, the mechanical tasks of a cell are driven by the nonequilibrium dynamics of cytoskeletal filaments and molecular motors—the same filaments and motors, reprogrammed by a variety of modulators, perform tasks ranging from cell movement to division. Similarly, many compartmentalization tasks are performed by liquid-like condensates of simple components, which act as membraneless organelles to localize particular molecules in space and time (e.g. for gene regulation or RNA processing). In a few cases, condensates combine and interact with the cytoskeleton to create still more complex phenomena, e.g. the nucleation of microtubule asters from the centrosome (a protein condensate) to form the mitotic spindle during cell division. Very little is known about the fundamental mechanisms of such filament-plus-condensate phenomena. Despite few examples, the landscape of behaviors that can be achieved through the combination of condensates, filaments, and motors appears vast. However, exploration has been hindered by a lack of systems that have sufficiently programmable and dynamically tunable interactions between component condensates, filaments, and motors. We proposed to combine programmable DNA condensates, filamentous microtubules, and light-controlled motors into self-organizing systems whose principles go beyond those that have been observed in nature. In one limit, our systems will use microtubules and motors to create the molecular analog of a network of roads, which will organize droplets of DNA condensates capable of carrying molecular cargo. DNA condensates coupled to motors will flow from one microtubule aster hub to another, with their direction and timing controlled by DNA circuits. In another limit, microtubules will swim through bulk DNA condensates and exhibit strong interactions with boundaries between different types of condensates. Microtubule swimmers will reflect, get trapped, or refract at boundaries, under a mechanical analog of the classical optical index of refraction. DNA condensates having different mechanical indexes of refraction will be used to construct the analog of optical lenses, so that microtubule swimmers can be manipulated like light—collimated, diffracted, focused, and sorted based on properties analogous to wavelength. These two limits define two new architectures, within which multiple new mechanistic principles for self-organization will be discovered and explored. To explore these architectures, the motor-based coupling between DNA condensates and filaments will be controlled in time and space through the use of opto-proteins that create reversible links between DNA condensates and motors upon illumination. For each principle of interest, patterns of light will create virtual experiments by defining patterns of activity where DNA condensates walk along filaments, or filaments swim through condensates, and patterns of inactivity which will serve either as controls, or as boundary conditions vital to create the desired phenomena. This research serves the goals of Basic Energy Sciences Biomolecular Material Program by elucidating the principles by which the emergent, nonequilibrium behavior of collections of DNA condensates, motors, and microtubules can be programmed by environmental light patterns to create complex motion and materials transport. Because DNA condensates can be readily coupled to virtually any high performance nanomaterial, from carbon nanotubes, to metal nanoparticles, to light harvesting systems, this work provides a path to the construction, self-maintenance and reconfiguration of materials relevant to the Department of Energy.

60 APPLIED LIFE SCIENCES↗

NASA NTRS1979

Thrust oscillations of the Space Shuttle solid rocket Booster motor during static tests

Thrust oscillations have occurred during static tests of Space Shuttle Booster solid rocket motors. These oscillations in measured axial thrust occurred primarily near 15 Hz; these oscillations late in the motor burn reach magnitudes up to approximately + or - 3% of motor thrust. The phenomenon has consistently occurred on the four demonstration motors which have been static tested and appears to be associated with small amplitude, 15 Hz pressure oscillations inside the motor. The source of the pressure oscillations is thought to be associated with the fundamental longitudinal acoustic resonance of the motor at 15 Hz. These thrust oscillations potentially can impact the design of the Space Shuttle vehicle structure. The demonstration motors have been instrumented with an array of transducers to aid in understanding the phenomenon. In addition to measuring axial and lateral thrust of the motor, pressure transducers were located to measure chamber pressure oscillations at the forward dome. Accelerometers and extensometers have measured motions of the structure. A modal survey was conducted on a fired motor to identify its structural dynamic characteristics, and these data were used to validate mathematical models of the motor in the static test facility.

Mason, D. R.↗

NASA NTRS2004

Bearingless Switched-Reluctance Motor Improved

The Morrison rotor, named after its inventor, is a hybrid rotor for use in a switched reluctance electric motor. The motor is characterized as bearingless in the sense that it does not rely on conventional mechanical bearings: instead, it functions as both a magnetic bearing and a motor. Bearingless switched-reluctance motors are attractive for use in situations in which large variations in temperatures and/or other extreme conditions preclude the use of conventional electric motors and mechanical bearings. In the Morrison motor, as in prior bearingless switched-reluctance motors, a multipole rotor is simultaneously levitated and rotated. In the prior motors, simultaneous levitation and rotation are achieved by means of two kinds of stator windings: (1) main motor windings and (2) windings that exert levitating forces on a multipole rotor. The multipole geometry is suboptimum for levitation because it presents a discontinuous surface to the stator pole faces, thereby degrading the vibration suppression capability of the magnetic bearing. The Morrison rotor simplifies the stator design in that it contains only one type of winding. The rotor is a hybrid that includes both (1) a circular lamination stack for levitation and (2) a multipole lamination stack for rotation. Simultaneous levitation and rotation at 6000 rpm were achieved with a prototype that included six rotor poles and eight stator poles. During normal operation, two of the four pairs of opposing stator poles (each pair at right angles to the other pair) levitate the rotor. The remaining two pairs of stator poles exert torque on the six-pole rotor lamination stack to produce rotation. The relative length of the circular and multipole lamination stacks on the rotor can be chosen to tailor the performance of the motor for a specific application. For a given overall length, increasing the length of the multipole stack relative to the circular stack results in an increase in torque relative to the levitation load capacity and vice versa.

Morrison, Carlos R.↗

NASA NTRS2008

A Cryogenic High-Power-Density Bearingless Motor for Future Electric Propulsion

The NASA Glenn Research Center (GRC) is developing a high-power-density switched-reluctance cryogenic motor for all-electric and pollution-free flight. However, cryogenic operation at higher rotational speeds markedly shortens the life of mechanical rolling element bearings. Thus, to demonstrate the practical feasibility of using this motor for future flights, a non-contact rotor-bearing system is a crucial technology to circumvent poor bearing life that ordinarily accompanies cryogenic operation. In this paper, a bearingless motor control technology for a 12-8 (12 poles in the stator and 8 poles in the rotor) switched-reluctance motor operating in liquid nitrogen (boiling point, 77 K (-196 C or -321 F)) was presented. We pushed previous disciplinary limits of electromagnetic controller technique by extending the state-of-the-art bearingless motor operating at liquid nitrogen for high-specific-power applications. The motor was levitated even in its nonlinear region of magnetic saturation, which is believed to be a world first for the motor type. Also we used only motoring coils to generate motoring torque and levitation force, which is an important feature for developing a high specific power motor.

Choi, Benjamin↗

NASA NTRS2003

Improved Bearingless Switched-Reluctance Motor

The Morrison rotor, named after its inventor, is a hybrid rotor for use in a bearingless switched-reluctance electric motor. The motor is characterized as bearingless in the sense that it does not rely on conventional mechanical bearings: instead, it functions as both a magnetic bearing and a motor. Bearingless switched-reluctance motors are attractive for use in situations in which large variations in temperatures and/or other extreme conditions preclude the use of conventional electric motors and mechanical bearings. In the Morrison motor, as in a prior bearingless switched-reluctance motor, a multipole rotor is simultaneously levitated and rotated. In the prior motor, simultaneous levitation and rotation are achieved by means of two kinds of stator windings: (1) main motor windings and (2) windings that exert levitating forces on a multipole rotor. The multipole geometry is suboptimum for levitation in that it presents a discontinuous surface to the stator pole faces, thereby degrading the vibration-suppression capability of the magnetic bearing. The Morrison rotor simplifies the stator design in that the stator contains only one type of winding. The rotor is a hybrid that includes both (1) a circular lamination stack for levitation and (2) a multipole lamination stack for rotation. A prototype includes six rotor poles and eight stator poles (see figure). During normal operation, two of the four pairs of opposing stator poles (each pair at right angles to the other pair) levitate the rotor. The remaining two pairs of stator poles exert torque on the six-pole rotor lamination stack to produce rotation. The relative lengths of the circular and multipole lamination stacks on the rotor can be chosen to tailor the performance of the motor for a specific application. For a given overall length, increasing the length of the multipole stack relative to the circular stack results in an increase in torque relative to levitation load capacity and stiffness, and vice versa.

Morrison, Carlos R.↗

NASA NTRS2012

Implementation of a Non-Metallic Barrier in an Electric Motor

Electric motors that run in pure oxygen must be sealed, or "canned," for safety reasons to prevent the oxygen from entering into the electrical portion of the motor. The current canning process involves designing a metallic barrier around the rotor to provide the separation. This metallic barrier reduces the motor efficiency as speed is increased. In higher-speed electric motors, efficiency is greatly improved if a very thin, nonmetallic barrier can be utilized. The barrier thickness needs to be approximately 0.025-in. (.0.6-mm) thick and can be made of a brittle material such as glass. The motors, however, designed for space applications are typically subject to high-vibration environments. A fragile, non-metallic barrier can be utilized in a motor assembly if held in place by a set of standard rubber O-ring seals. The O-rings provide the necessary sealing to keep oxygen away from the electrical portion of the motor and also isolate the fragile barrier from the harsh motor vibration environment. The compliance of the rubber O-rings gently constrains the fragile barrier and isolates it from the harsh external motor environment. The use of a non-metallic barrier greatly improves motor performance, especially at higher speeds, while isolating the electronics from the working fluid with an inert liner.

M?Sadoques, George↗

NASA NTRS2015

Performance Comparisons and Down Selection of Small Motors for Two-Blade Heliogyro Solar Sail 6U CubeSat

This report compiles a review of 130 commercial small scale motors (piezoelectric and electric motors) and almost 20 researched-type small scale piezoelectricmotors for potential use in a 2 blades Heliogyro Solar Sail 6U CubeSat. In this application, a motor and gearhead (drive system) will deploy a roll of solar sailthin film (2 um thick)accommodated in a 2U CubeSat (100 x 200 x 100 mm) housing. The application requirements are: space rated, output torque at fulldeployment of 0.8 Nm, reel speed of 3 rpm, drive system weight limited to 150 grams, diameter limited to 50 mm, and the length not to exceed 40 mm. The 50mm diameter limit was imposed as motors with larger diameters would likely weigh too much and use more space on the satellite wall. This would limit theamount of the payload. The motors performance are compared between small scale, volume within 3x102 cm3 (3x105 mm3), commercial electric DC motors,commercial piezoelectric motors, and researched-type (non-commercial) piezoelectric motors extracted from scientific and product literature. The comparisonssuggest that piezoelectric motors without a gearhead exhibit larger output torque with respect to their volume and weight and require less input power toproduce high torque. A commercially available electric motor plus a gearhead was chosen through a proposed selection process to meet the applications designrequirements.

Wiwattananon, Peerawan↗

NASA NTRS2019

Design of a Nozzle for the Spyder 2nd Stage Solid Rocket Motor

During the 2019 summer term, the author worked with a group of four interns to complete the preliminary design of a 2nd stage solid rocket motor for Up Aerospace’s Spyder Launch Vehicle. The Spyder vehicle is a four stage, solid fuel rocket designed as part of collaboration between NASA and Up Aerospace to develop a vehicle capable of delivering a 10 kg, 6U CubeSat into a 350 km, circular, low Earth orbit. As part of the agreement, NASA is tasked with designing high performance 2nd, 3rd, and 4th stages while Up Aerospace will provide the 1st stage, derived from the first stage of the company’s sub-orbital Spaceloft XL vehicle. Previous intern teams have designed the 3rd and 4th stages, which left the preliminary design of the 2nd stage motor to be completed this summer. The purpose of this report is to highlight a trade study which the author conducted to determine the nozzle geometry which would most benefit the performance of the 2nd stage motor. In this study, various nozzle parameters such as throat radius (RSI), expansion ratio, mass and their effects on the Isp and Delta V of the 2nd Stage were investigated. From this study, a nozzle geometry providing the necessary performance was chosen and implemented as part of the preliminary design of the 2nd stage motor. To mature the 2nd stage motor design, a trade space was needed to determine the nozzle configuration which would most benefit the performance of the 2nd stage. The trade space established did not only evaluate different expansion ratios for the same throat radius, but also investigated the possible performance gained from decreasing the throat radius to increase the expansion ratio and Isp capable of being delivered by the nozzle. Decreasing the throat radius would cause the chamber pressure to increase, consequently increasing the case and insulation mass required to safely operate a motor at higher pressures. To account for this factor, accurate estimates of inert mass first needed to be established. After doing so, the effects of varying nozzle expansion ratios, exit half angles, and subsequently length and mass were evaluated against motor and nozzle performance factors such as delta V and Isp. For this study, four throat radii ranging from 1.75” to 2.375” and consequently four different chamber pressures ranging 550 psia to 1200 psia were investigated. BACKGROUND To launch into Low Earth Orbit, a payload needs to be accelerated to the orbital velocity necessary to keep it from falling back to Earth. The change in velocity required between launch and orbital insertion is known as Delta V. The Delta V which a rocket or stage can deliver can be calculated using the Ideal Rocket equation, 𝛥𝑉=−𝑔0∗𝐼𝑠𝑝∗ln(𝑀𝑓𝑀𝑖) (3) Where 𝑔0 is the acceleration due to gravity at the earth’s surface, 𝐼𝑠𝑝 is the specific impulse of the rocket, 𝑀𝑖 is the initial mass of the rocket, and 𝑀𝑓 is the final mass of the rocket after burnout. From preliminary calculations beyond the scope of this paper, it was determined that 30500 ft/s of delta V would be required for a payload to be inserted into a 350 km circular orbit around the Earth. Using the known masses and Isp values of the 1st, 3rd, and 4th stages and equation 3, the delta V of each stage was calculated. The delta V required by the 2nd stage could then be found by taking the difference between the total delta V required and the delta V of the 1st, 3rd, and 4th stages. From this, the required delta V of the 2nd Stage was calculated to be 7340 ft/s. Specific impulse is an efficiency factor of the nozzle which defines the impulse delivered by the motor per unit of propellant weight. The main variables of a nozzle’s specific impulse investigated in this trade were exit cone half angle, throat radius, and expansion ratio which is affected by the throat radius. The expansion ratio, ε, of a nozzle is defined as the ratio between the nozzle exit area and throat area, and can be calculated using the equation, ε=𝑅𝑒𝑥𝑖𝑡2𝑅𝑠𝑖2 (2) Where 𝑅𝑒𝑥𝑖𝑡 is the radius of the nozzle’s exit and 𝑅𝑠𝑖 is the radius of the nozzle’s throat. A larger expansion ratio and smaller exit half angle will increase the Isp of a nozzle by allowing the gas to expand more and by allowing more of the exhaust gas to produce thrust in the direction of the motor’s central axis. A cross section view of the 2nd Stage motor with the major components annotated is provided in figure 1.

Bennett, Daniel↗

DOE OSTI2022

Efficient, Compact, and Smooth Variable Propulsion Motor (Final Report)

In this project, a new architecture of highly efficient hydraulic motor was developed for the propulsion of off-highway vehicles. The motor uses an adjustable linkage driving a cam to vary the displacement of the piston, resulting in a Variable Displacement Linkage Motor (VDLM). The motor uses low friction rolling element bearings to significantly reduce mechanical friction, especially in the demanding low-speed high-torque conditions experienced by off-highway vehicles. The VDLM has high torque capabilities for its size due to the radial piston packaging and use of a multi-lobe cam. A VDLM is very smooth due to the ability to tune the torque ripple through the design of the cam profile. The project was divided into three periods. During the first period, a dynamic model was constructed of the motor to predict the performance of the motor and the vehicle. During the second period, a single-cylinder learning prototype was designed, built, and tested to validate the models constructed in the first period. In the third period, a multi-cylinder prototype motor was optimized, designed, fabricated, and tested. The motor demonstrated excellent mechanical efficiency (above 92.5% across the range of displacements), but the experimentally measure volumetric efficiency was lower than expected due to higher leakage rates created by the poor tolerance control on the prototype. To validate the dynamic models developed in the first period and better understand design trade-offs. In the third period a multi-cylinder concept demonstration prototype will be designed, fabricated, and tested. The final prototype will be tested on a motor dynamometer and will be utilized in hardware-in-the-loop testing to demonstrate its efficiency and performance impacts on the overall drive train. The experimental results were used in a drive train simulation of a compact track loader operating through a drive cycle. Using the VDLM in a hydrostatic circuit yielded 17.1% reduction in fuel consumption and 36.5% reduction in a series hybrid transmission.

99 GENERAL AND MISCELLANEOUS↗

NASA NTRS1975

Manufacture and static firing of X259-E6 rocket motor serial number XJ04/0001

A single motor was cast and static fired to demonstrate the performance of high energy crosslinked double base (XLDB) propellant in standard X259 rocket motor hardware. Prior to motor fabrication, the motor was analyzed to predict the results of static firing the X259 motor loaded with XLDB propellant. As a result of the analyses, a forward dome shrinkage liner was added to the design. With this design change it was determined that adequate margins of safety existed. The motor, designated the X259-E6 model with serial number XJ04/0001, was fabricated using a slurry-casting technique and was assembled with a standard X259-B4 nozzle which had the nozzle throat machined to a smaller inside diameter than the B4 model and the exit cone cut short for Bacchus Works altitude expansion. The motor was static fired on 20 February 1974 with the nozzle failing during motor operation. Nozzle failure was attributed to spalling of the throat material leading to complete nozzle break-up. However, the propellant functioned as predicted in the motor chamber, ignition was normal, and char and erosion of the internal insulator were as expected.

Robertson, D. R.↗

NASA NTRS1981

Straight and chopped dc performance data for a General Electric 5BT 2366C10 motor and an EV-1 controller

Performance data on the General Electric 5BT 2366C10 series wound dc motor and EV-1 Chopper Controller is supplied for the electric vehicle manufacturer. Data is provided for both straight and chopped dc input to the motor, at 2 motor temperature levels. Testing was done at 6 voltage increments to the motor, and 2 voltage increments to the controller. Data results are presented in both tabular and graphical forms. Tabular information includes motor voltage and current input data, motor speed and torque output data, power data and temperature data. Graphical information includes torque-speed, motor power output-speed, torque-current, and efficiency-speed plots under the various operating conditions. The data resulting from this testing shows the speed-torque plots to have the most variance with operating temperature. The maximum motor efficiency is between 86% and 87%, regardless of temperature or mode of operation. When the chopper is utilized, maximum motor efficiency occurs when the chopper duty cycle approaches 100%.

Edie, P. C.↗

NASA NTRS1990

Control Circuit For Two Stepping Motors

Control circuit operates two independent stepping motors, one at a time. Provides following operating features: After selected motor stepped to chosen position, power turned off to reduce dissipation; Includes two up/down counters that remember at which one of eight steps each motor set. For selected motor, step indicated by illumination of one of eight light-emitting diodes (LED's) in ring; Selected motor advanced one step at time or repeatedly at rate controlled; Motor current - 30 mA at 90 degree positions, 60 mA at 45 degree positions - indicated by high or low intensity of LED that serves as motor-current monitor; Power-on reset feature provides trouble-free starts; To maintain synchronism between control circuit and motors, stepping of counters inhibited when motor power turned off.

Ratliff, Roger↗

NASA NTRS1989

Analytical and experimental study of high phase order induction motors

Induction motors having more than three phases were investigated to determine their suitability for electric vehicle applications. The objective was to have a motor with a current rating lower than that of a three-phase motor. The name chosen for these is high phase order (HPO) motors. Motors having six phases and nine phases were given the most attention. It was found that HPO motors are quite suitable for electric vehicles, and for many other applications as well. They have characteristics which are as good as or better than three-phase motors for practically all applications where polyphase induction motors are appropriate. Some of the analysis methods are presented, and several of the equivalent circuits which facilitate the determination of harmonic currents and losses, or currents with unbalanced sources, are included. The sometimes large stator currents due to harmonics in the source voltages are pointed out. Filters which can limit these currents were developed. An analysis and description of these filters is included. Experimental results which confirm and illustrate much of the theory are also included. These include locked rotor test results and full-load performance with an open phase. Also shown are oscillograms which display the reduction in harmonic currents when a filter is used with the experimental motor supplied by a non-sinusoidal source.

Klingshirn, Eugene A.↗

NASA NTRS1995

Motor Drive Technologies for the Power-by-Wire (PBW) Program: Options, Trends and Tradeoffs

Power-By-Wire (PBW) is a program involving the replacement of hydraulic and pneumatic systems currently used in aircraft with an all-electric secondary power system. One of the largest loads of the all-electric secondary power system will be the motor loads which include pumps, compressors and Electrical Actuators (EA's). Issues of improved reliability, reduced maintenance and efficiency, among other advantages, are the motivation for replacing the existing aircraft actuators with electrical actuators. An EA system contains four major components. These are the motor, the power electronic converters, the actuator and the control system, including the sensors. This paper is a comparative literature review in motor drive technologies, with a focus on the trends and tradeoffs involved in the selection of a particular motor drive technology. The reported research comprises three motor drive technologies. These are the induction motor (IM), the brushless dc motor (BLDCM) and the switched reluctance motor (SRM). Each of the three drives has the potential for application in the PBW program. Many issues remain to be investigated and compared between the three motor drives, using actual mechanical loads expected in the PBW program.

Elbuluk, Malik E.↗

NASA NTRS1993

The Castor 120 (TM) Motor: Development and Qualification Testing Results

This paper discusses Thiokol Corporation's static test results for the development and qualification program of the Castor 120(TM) motor. The demonstration program began with a 25,000-pound motor to demonstrate the new technologies and processes that would be used on the larger Castor 120(TM) motor. The Castor 120(TM) motor was designed to be applicable as a first stage, second stage, or strap-on motor. Static test results from the Castor 25 and two Castor 120(TM) motors are discussed in this paper. The results verified the feasibility of tailoring the propellant grain configuration and nozzle throat diameter to meet various customer requirements. The first and second motors were conditioned successfully at ambient temperature and 28 F, respectively, to demonstrate that the design could handle a wide range of environmental launch conditions. Furthermore, the second Castor 120(TM) motor demonstrated a systems tunnel and forward skirt extension to verify flight-ready stage hardware. It is anticipated that the first flight motor will be ready by the fall of 1994.

Jack G Hilden↗

NASA NTRS1996

Application of Two-Phase CFD to the Design and Analysis of a Subscale Motor Experiment to Evaluate Propellant Slag Production

The redesigned solid rocket motor (RSRM) Pressure Perturbation Investigation Team concluded that the cause of recent pressure spikes during both static and flight motor burns was the expulsion of molten aluminum oxide slag from a pool which collects in the aft end of the motor around the submerged nozzle nose during the last half of motor operation. It is suspected that some motors produce more slag than others due to differences in aluminum oxide agglomerate particle sizes which may relate to subtle differences in propellant ingredient characteristics such as particle size distribution, contaminants, or processing variations. In order to determine the effect of suspect propellant ingredient characteristics on the propensity for slag production in a real motor environment, a subscale motor experiment was designed. An existing 5 inch ballistic test motor was selected as the basic test vehicle due to low cost and quick turn around times. The standard converging/diverging nozzle was replaced with a submerged nozzle nose design to provide a positive trap for the slag which would increase both the quantity and repeatability of measured slag weights. Computational fluid dynamics (CFD) was used to assess a variety of submerged nose configurations to identify the design which possessed the best capability to reliably collect slag. CFD also was used to assure that the final selected nozzle design would result in flow field characteristics such as dividing streamline location, nose attach point, and separated flow structure which would have similtude with the RSRM submerged nozzle nose flow field. It also was decided to spin the 5 inch motor about its longitudinal axis to further enhance slag collection quantities. Again, CFD was used to select an appropriate spin rate along with other considerations, including the avoidance of burn rate enhancement from radial acceleration effects.

Whitesides, R. Harold↗