Search NASA⌕ Search

SEARCH · Search NASA

Results for “mullite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Evaluation of low cost/high temperature insulation, July 1974 - June 1975

Six fiber products and six insulation blankets comprising silica, alumina, zirconia, mullite, and mixed ceramic systems were subjected to furnace exposures up to 500 hours at temperatures of 1000 to 1600 C and evaluated for chemical and dimensional stability and for changes in thermal conductivity. Alumina, zirconia, and mullite fibers were fabricated into reusable surface insulation (RSI) tile by water-felting and reimpregnation with ethyl silicate. Specimens were exposed to 25 thermal cycles at 1200 C and 1400 C and a pressure of 10 and 32 torr, respectively. Production costs for 930 sq m (10,000 sq ft) of blanket insulation and of alumina RSI tile were developed.

Strauss, E. L.↗
NASA NTRS1976

Dip coating process: Silicon sheet growth development for the large-area silicon sheet task of the low-cost silicon solar array project

To date, an experimental dip-coating facility was constructed. Using this facility, relatively thin (1 mm) mullite and alumina substrates were successfully dip-coated with 2.5 - 3.0 ohm-cm, p-type silicon with areas of approximately 20 sq cm. The thickness and grain size of these coatings are influenced by the temperature of the melt and the rate at which the substrate is pulled from the melt. One mullite substrate had dendrite-like crystallites of the order of 1 mm wide and 1 to 2 cm long. Their axes were aligned along the direction of pulling. A large variety of substrate materials were purchased or developed enabling the program to commence a substrate definition evaluation. Due to the insulating nature of the substrate, the bottom layer of the p-n junction may have to be made via the top surface. The feasibility of accomplishing this was demonstrated using single crystal wafers.

Heaps, J. D.↗
NASA NTRS1976

Dip coating process: Silicon sheet growth development for the large-area silicon sheet task of the low-cost silicon solar array project

The technical and economic feasibility of producing solar cell quality sheet silicon by dip-coating one surface of carbonized ceramic substrates with a thin layer of large grain polycrystalline silicon was investigated. The dip-coating methods studied were directed toward a minimum cost process with the ultimate objective of producing solar cells with a conversion efficiency of 10% or greater. The technique shows excellent promise for low cost, labor-saving, scale-up potentialities and would provide an end product of sheet silicon with a rigid and strong supportive backing. An experimental dip-coating facility was designed and constructed, several substrates were successfully dip-coated with areas as large as 25 sq cm and thicknesses of 12 micron to 250 micron. There appears to be no serious limitation on the area of a substrate that could be coated. Of the various substrate materials dip-coated, mullite appears to best satisfy the requirement of the program. An inexpensive process was developed for producing mullite in the desired geometry.

Heaps, J. D.↗
NASA NTRS1981

Early development of ceramic fiber insulation for the Space Shuttle

The evolution of reusable surface insulation is described, with attention to the mullite and other aluminosilicates, zirconia, and silicon carbide-coated carbon compositions experimented with in the late 1960s and early 1970s. Evaluation and development concentrated in this period on such aspects of design and material properties as cold soak performance, attachment, shock impingement, surface coating cracks, and tile gap design and heating. In addressing the central problem of heat-shield thermal conductivity, it was found that for a given density, silica fibers had a lower conductivity than those of mullite. This was due to the one-micron, as opposed to 4.7-micron, diameter of the silica fibers, which resulted in smaller pores and therefore less convective and radiative heat transfer. Attention is also given to tile coating materials and the high-temperature processes by which they were applied.

Buckley, J. D.↗
NASA NTRS1989

Friction and wear of oxide-ceramic sliding against IN-718 nickel base alloy at 25 to 800 C in atmospheric air

The friction and wear of oxide-ceramics sliding against the nickel base alloy IN-718 at 25 to 800 C were measured. The oxide materials tested were mullite (3Al2O3.2SiO2); lithium aluminum silicate (LiAlSi(x)O(y)); polycrystalline monolithic alpha alumina (alpha-Al2O3); single crystal alpha-Al2O3 (sapphire); zirconia (ZrO2); and silicon carbide (SiC) whisker-reinforced Al2O3 composites. At 25 C the mullite and zirconia had the lowest friction and the polycrystalline monolithic alumina had the lowest wear. At 800 C the Al2O3-8 vol/percent SiC whisker composite had the lowest friction and the Al2O3-25 vol/percent SiC composite had the lowest wear. The friction of the Al2O3-SiC whisker composites increased with increased whisker content while the wear decreased. In general, the wear-resistance of the ceramics improve with their hardness.

Sliney, Harold E.↗
NASA NTRS1989

Crystallization of a barium-aluminosilicate glass

The crystallization of a celsian glass composition was investigated as a possible high-temperature ceramic matrix material. Heat treatments invariably resulted in crystallization of the hexaclesian phase unless a flux, such as lithia, was added or a nucleating agent used (e.g., celsian seeds). TEM analysis revealed complex microstructures. Glasses with Mo additions contained hexacelsian, mullite, and an Mo-rich glass. Li2O additions stabilized celsian but mullite and Mo-rich glass were still present.

Drummond, C. H., III↗
NASA NTRS1991

The high temperature creep behavior of oxides and oxide fibers

A thorough review of the literature was conducted on the high-temperature creep behavior of single and polycrystalline oxides which potentially could serve as fiber reinforcements in ceramics or metal matrix applications. Sapphire when oriented with the basal plane perpendicular to the fiber axis (c-axis oriented) is highly creep resistant at temperatures in excess of 1600 C and applied loads of 100 MPa and higher. Pyramidal slip is preferentially activated in sapphire under these conditions and steady-state creep rates in the range of 10(exp -7) to 10 (exp -8)/s were reported. Data on the creep resistance of polycrystalline beryllia suggest that C-axiz oriented single crystal beryllia may be a viable candidate as a fiber reinforcement material; however, the issure of fabricability and moisture sensitivity must be addressed for this material. Yttrium aluminum garnet (YAG) also appears to be a fiber candidate material having a high resistance to creep which is due to it's complex crystal structure and high Peierl resistance. The high creep resistance of garnet suggests that there may be other complex ternary oxides such as single crystal mullite which may also be candidate materials for fiber reinforcements. Finally, CVD and single crystal SiC, although not oxides, do possess a high resistance to creep in the temperature range between 1550 and 1850 C and under stresses of 110 to 220 MPa. From a review of the literature, it appears that for high creep resistant applications sapphire, silicon carbide, yttrium aluminum garnet, mullite, and beryllia are desirable candidate materials which require further investigation.

Jones, Linda E.↗
NASA NTRS2000

Internally Cooled Monolithic Silicon Nitride Aerospace Components

A set of rapid prototyping (RP) processes have been combined with gelcasting to make ceramic aerospace components that contain internal cooling geometry. A mold and core combination is made using a MM6Pro (Sanders Prototyping, Inc.) and SLA-250/40 (3Dsystems, Inc.). The MM6Pro produces cores from ProtoBuild (trademarked) wax that are dissolved in room temperature ethanol following gelcasting. The SLA-250/40 yields epoxy/acrylate reusable molds. Parts produced by this method include two types of specimens containing a high density of thin long cooling channels, thin-walled cylinders and plates, as well as a model hollow airfoil shape that can be used for burner rig evaluation of coatings. Both uncoated and mullite-coated hollow airfoils has been tested in a Mach 0.3 burner rig with cooling air demonstrating internal cooling and confirming the effectiveness of mullite coatings.

Best, Jonathan E.↗
NASA NTRS2003

Sintering and Interface Strain Tolerance of Plasma-Sprayed Thermal and Environmental Barrier Coatings

Ceramic thermal and environmental barrier coatings will be more aggressively designed to protect gas turbine engine hot section SiC/SiC Ceramic Matrix Composite (CMC) components in order to meet future engine higher fuel efficiency and lower emission goals. A coating system consisting of a zirconia-based oxide topcoat (thermal barrier) and a mullite/BSAS silicate inner coat (environmental barrier) is often considered a model system for the CMC applications. However, the coating sintering, and thermal expansion mismatch between the zirconia oxide layer and the silicate environmental barrier/CMC substrate will be of major concern at high temperature and under thermal cycling conditions. In this study, the sintering behavior of plasma-sprayed freestanding zirconia-yttria-based thermal barrier coatings and mullite (and/or barium-strontium-aluminosilicate, i.e., BSAS) environmental barrier coatings was determined using a dilatometer in the temperature range of 1200-1500 C. The effects of test temperature on the coating sintering kinetics were systematically investigated. The plasma-sprayed zirconia-8wt.%yttria and mullite (BSAS) two-layer composite coating systems were also prepared to quantitatively evaluate the interface strain tolerance of the coating system under thermal cycling conditions based on the dilatomentry. The cyclic response of the coating strain tolerance behavior and interface degradation as a function of cycle number will also be discussed.

Zhu, Dongming↗
NASA NTRS2016

Environmental Barrier Coatings for Ceramic Matrix Composites - An Overview

Ceramic Matrix Composites (CMCs) are increasingly being considered as structural materials for advanced power generation equipment. Broadly speaking the two classes of materials are oxide-based CMCs and non-oxide based CMCs. The non-oxide CMCs are primarily silicon-based. Under conditions prevalent in the gas turbine hot section the water vapor formed in the combustion of gaseous or liquid hydrocarbons reacts with the surface-SiO2 to form volatile products. Progressive surface recession of the SiC-SiC CMC component, strength loss as a result of wall thinning and chemical changes in the component occur, which leads to the loss of structural integrity and mechanical strength and becomes life limiting to the equipment in service. The solutions pursued to improve the life of SiC-SiC CMCs include the incorporation of an external barrier coating to provide surface protection to the CMC substrate. The coating system has become known as an Environmental Barrier Coating (EBC). The relevant early coatings work was focused on coatings for corrosion protection of silicon-based monolithic ceramics operating under severely corrosive conditions. The development of EBCs for gas turbine hot section components was built on the early work for silicon-based monolithics. The first generation EBC is a three-layer coating, which in its simplest configuration consists of a silicon (Si) base coat applied on top of the CMC, a barium-strontium-aluminosilicate (BSAS) surface coat resistant to water vapor attack, and a mullite-based intermediate coating layer between the Si base coat and BSAS top coat. This system can be represented as Si-Mullite-BSAS. While this baseline EBC presented a significant improvement over the uncoated SiC-SiC CMC, for the very long durations of 3-4 years or more expected for industrial operation further improvements in coating durability are desirable. Also, for very demanding applications with higher component temperatures but shorter service lives more rugged EBCs will be necessary. A second generation of EBCs incorporates rare earth silicates which have extremely favorable resistance against environmental attack and a higher temperature capability. Performance data for this class of EBCs is more limited and especially field data are not as extensive as for the first generation EBCs. Extensive laboratory, rig and engine testing, including testing of EBC coated SiC-SiC CMCs in actual field applications is in progress. The development of next generation EBCs with even higher temperature capability than the second generation EBC is also underway. This paper will discuss the current status of EBC technology and future direction based on literature survey.

Laboratory↗
DOE OSTI2024

Reinforcement induced microcracking during the conversion of polymer-derived ceramics

This study investigates the role of discontinuous reinforcement on the microcracking of a preceramic polymer matrix during polymer to ceramic conversion. The material system comprised a carbosilane-based, preceramic polymer reinforced with mullite particles. The preceramic resin slurry was formulated for photopolymerization on a digital light projection 3D printer. Micro X-ray computed tomography, using a synchrotron light source, monitored a printed composite part during pyrolysis. The conversion of the carbosilane matrix into Si(O)C generated microcracks in the matrix that radially extended from particles. The likelihood of microcrack formation positively correlated with particle size. The largest particles (>10 4 µm 3 volume or >60 µm side length) always abutted microcracks, while the matrix surrounding smaller particles (<5 µm) was free of microcracks. Numerical calculations showed the particles resist the shrinking matrix during its conversion. This created tensile stresses within the matrix. The driving force for microcrack growth was also analyzed with regard to the influence of matrix material parameters, particle form-factor and crack length. These results reveal the need to consider the form factor of discontinuous reinforcements, with regard to the material properties of the polymer-derived ceramic, in order to reduce or eliminate defects in the final part.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ observation of the deformation and fracture of an alumina-alumina ceramic-matrix composite at elevated temperature using x-ray computed tomography

The deformation and fracture of a 0/90° Nextel 720 mullite fibre / alumina matrix ceramic-matrix composite material has been observed by in situ synchrotron x-ray computed micro-tomography at ambient temperature and at 1100 °C. A three-point loading configuration was used and samples were loaded monotonically until final fracture. Here, the flexural strength was found to be unaffected by temperature. 3D visualisation of the microstructure showed fracture occurred by propagation of internal cracks at stresses close to the flexural strength. Shear fractures propagated across fibre bundles that were oriented perpendicular to the flexural stress at both room temperature and 1100 °C. At the higher temperature, an additional failure mode of delamination was observed, that may arise from relaxation of thermal residual stresses and creep.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Impact damage of narrow silicon carbide (SiC) ceramics with and without environmental barrier coatings (EBCs) by various foreign object debris (FOD) simulants

The leading and trailing edges of turbine airfoils are highly susceptible to impact by foreign object debris (FOD) entrained in the gas stream of turbine engines. In this study, a narrow specimen geometry is implemented to study the FOD impact behavior of low curvature airfoil edges. Silicon carbide (SiC) ceramic specimens with and without an environmental barrier coating (EBC) are used as target materials. The EBC consists of an air plasma sprayed mullite topcoat (~ 166 µm) and silicon bond coat (~ 58 µm). Spherical (∅ 1.5 mm) FOD simulants of silicon nitride (Si3N4), partially stabilized zirconia (PSZ), and steel are used as impactors. Additionally, a modified gas gun is used to generate impact damage at normal incidence and velocities ranging between 300 to 400 m/s. In situ phase contrast X-ray radiographs, which render 2D representations of the internal transient damage, are captured during the impact experiments. Impactor hardness and toughness are found to primarily influence damage in the coating. Relative to wide specimens, the narrow specimens experience a greater level of cracking and this is postulated to result from reduced self-confinement. Irrespective of specimen geometry and impactor material type, limited cracking (i.e. enhanced shielding) is observed for the coated condition.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Alumina-based filters made via binder jet 3D printing of alumina powder, colloidal silica infiltration, and sintering

Alumina-based, porous filter media was made via a binder jet 3D printing process consisting of an alumina powder printing step with subsequent heating, colloidal silica infiltration, drying, and sintering to consolidate particles yet retain a net open porous microstructure. The composites made were alumina-silica or alumina-mullite, where the silica sintering aid was used to densify and join the alumina particles. The resulting composite structures had open porosities in the 25–31 vol% range as measured by Archimedes density. Pressure drops were measured across the filter media at constant flow rates to compare disc shapes and complex, 3D printed filters based on the N95 design requirements. Complex, 3D-printed alumina composites were produced with acceptable pressure drops for N95 implementation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In situ characterization of foreign object damage (FOD) in environmental-barrier-coated silicon carbide (SiC) ceramic

Environmental barrier coatings (EBCs) protect advanced ceramics and ceramic matrix composites (CMCs) from oxidation and corrosion in gas turbine engine environments. Foreign object damage (FOD), where debris impact the protective coatings, is a critical hazard which limits the turbine durability. Despite previous efforts to understand FOD in EBCs, a detailed understanding of the fundamental transient damage mechanisms is still lacking. In the current work, the real-time FOD behavior of a Mullite / Silicon EBC was visualized via a dynamic synchrotron X-ray source in phase contrast imaging (PCI) configuration. Prior to the in situ FOD experiments, the microstructure and composition of the coating were respectively characterized using a scanning electron microscope (SEM) and X-ray diffraction (XRD). The variation in the properties of the debris was modeled by ~ 1.5 mm diameter Partially Stabilized Zirconia (PSZ) and Silicon Nitride (Si 3 N 4 ) spheres. A modified light-gas gun setup, synchronized with the X-ray beam, was used to propel the projectiles at velocities ranging between 300 and 355 m·s -1 . Coated samples were impacted under a fully backed support configuration and at normal incidence. Coating penetration and delamination, as well as projectile deformation at the bond coat resulted for FOD by PSZ spheres. Comparatively, projectile fracture, with subsequent rebound of fragments, as well as complete coating penetration and delamination at the substrate interface occurred for FOD by Si 3 N 4 spheres. It should be noted that only cone cracking was observed for FOD by PSZ spheres while back surface cracking was present for both projectile types. Qualitative understanding of the driving forces for the observed damage mechanisms were provided.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Ultra High Speed High Temperature Motor

The goal of this project was to develop a high-speed, high-temperature motor capable of operating at 650 ºC, 60,000 rpm, and 125 kW with 50 kW/L. Key objectives to achieve this goal were to develop a suitable high-temperature wire, designing and fabricating rotor and stator subassemblies, designing an inverter assembly, and thermomechanical validation of the fully assembled motor. Four candidates for high-temperature wire were evaluated using test solenoid structures and finite element analysis modeling. The best candidate was a silicone-enameled copper wire suitable for continuous operation at 593 ºC. The rotor for the motor was designed to use a composite material comprised of 74% iron and 26% mullite by volume. This material would be suitable for 3D printing of the rotor. At the end of the project a vacuum mixer was under construction to produce the bubble-free material needed to achieve the highest strength composite after 3D printing. Rotor testing at 60,000 rpm would have commenced immediately following the additive manufacturing process. The project abruptly ended when key personnel left the project without notice.

42 ENGINEERING↗
DOE OSTI2023

Pretreatment of Bituminous Coal By-Products for the Hydrometallurgical Extraction of Rare Earth Elements

Low-temperature plasma (LTP) oxidation has been widely used to study the mineralogy of the mineral matter existing in coal sources. The current study investigated the potential of LTP oxidation as a pre-treatment method to improve rare earth element (REE) leachability from coal and its by-products. Representative density-fractionated samples of Baker and Fire Clay coarse refuse seam materials were ground to a top size of 180 µm and subjected to low-temperature plasma oxidation. Subsequently, the treated samples were leached at 1% w/v solids concentration and 75 °C for 5 h using (i) de-ionized (DI) water, (ii) 0.1 mol/L of ammonium sulfate, and (iii) 1.2 mol/L of sulfuric acid. It was determined that LTP treatment improved REE leaching characteristics, especially the leaching of heavy REEs (HREE), existing in the lighter density fractions of the Baker seam coarse refuse material. For instance, the HREE recovery for the 1.6 specific gravity (SG) float fraction increased from 8% to 33% using 0.1 mol/L of ammonium sulfate solution after 32 h of LTP treatment. This finding indicated that HREEs associated with the organic matter were released by the LTP treatment and adsorbed onto the surfaces of highly negative charged mineral matter and was exchanged with ammonium to allow their recovery. Similarly, when using 1.2 mol/L of sulfuric acid, the HREE recovery increased from 23% to 53% for the 1.6 SG float fraction. Interestingly, LTP oxidation did not provide significant improvement in REE recovery from the 2.2 sink density fractions, which was likely due to its lower organic content. No significant benefits were observed when treating the Fire Clay coarse refuse material, which was likely due to the lack of organic affinity and the difficult-to-leach REE minerals associated with the coal source such as monazite, xenotime, and zircon. Conversely, high-temperature oxidation within a temperature range of 600–750 °C significantly improved REE leaching characteristics for both coal sources. Improvement in REE recovery was due to decarbonization of the material, clay dehydroxylation and subsequent conversion of liberated REE-bearing minerals into a more leachable form. However, increasing the temperature above 800 °C decreased REE recovery due to the conversion of meta-kaolinite into mullite, which is chemically stable.

58 GEOSCIENCES↗