SEARCH · Search NASA

Results for “openFOAM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Three-Dimensional CFD Analysis of Construction Design Alternatives for an ERDC Coastal and Hydraulics Laboratory Flow Accelerator

The U.S. Army Engineer Research and Development Center, ERDC, Coastal and Hydraulics Laboratory in Vicksburg Mississippi is planning to build a large flume with a 10-foot-wide flow channel. Three-dimensional Computational Fluid Dynamics (CFD) analysis was used in the design of the flume entry and flow accelerator sections that feed into the 10-foot-wide channel. The design is based on the plans of the existing fiberglass flume inlet at the Turner-Fairbank Highway Research Center (TFHRC) J. Sterling Jones Hydraulics Research Laboratory in McLean Virginia. The TFHRC flume inlet feeds water to a 6-foot-wide flume channel, and therefore a scale up factor of 10/6 in the width of the inlet section of the TFHRC flume would meet the width requirement of the ERDC flume channel. The CFD analysis was performed using STAR-CCM+ commercial CFD software. Additional analysis was done with the open-source CFD software, OpenFOAM, to cross-check the analysis of one of the cases with a code-to-code comparison.

42 ENGINEERING↗

DOE OSTI2022

MOSCATO Development and Integration in Fiscal Year 2022

During FY21, we conducted ongoing development work for the MOSCATO (Molten Salt Chemistry and Transport) solver. The code development work primarily consisted of transitioning capabilities from the original version of the solver, which was written in OpenFOAM, into Nek5000. In doing so, a fast, highly parallelizable solver was created that is capable of complex chemistry and corrosion simulations for engineering-scale molten salt systems. The Nek5000 version of MOSCATO is now fully featured and capable of higher-fidelity simulations than were previously possible. Demonstration cases including a thermal convection loop have been simulated to test these new capabilities. We built upon the work for FY22 and improved the code from several different perspectives. First, we improved the user interface by adding a new component to the official Nek5000 input file (.par). This new part contains documents parameters like, salt properties (density, viscosity, Cp, thermal conductivity), diffusion coefficients, standard potential, etc. Second, we built a conversion script to extract salt properties from the MSTDB-TP salt database and write to MOSCATO input file. Third, we migrated the code to NekRS, which is the GPU branch of Nek5000 and suitable for next generation supercomputers. Verification and Validation (V&V) work was also continued in FY22. Two tasks were performed. The first V&V task involved the validation of the Poisson-Nernst-Planck equation solver and Butler-Volmer electrode kinetics, by comparing with numerical and experimental data about thermoelectric cells. The second task involved the comparisons to corrosion results from a thermal convection loop run during the MSRE era. Satisfactory agreement was obtained from both tasks.

Yuan, Haomin↗

DOE OSTI2023

Laser heating and evaporation of a single droplet

The laser technology is being abundantly studied for controlled energy deposition for a range of applications in aerodynamic flow control, material processing, ignition, and combustion. The absorption of laser radiation by liquid droplets affects further propagation of laser in the atmosphere and causes bleaching of suspended droplets while the ignition and combustion characteristics in combustors are influenced by the evaporation rate of the sprayed fuel. In this work, we present a multi-dimensional mathematical model built on OpenFOAM for laser heating and evaporation of a single droplet in the diffusion dominated regime taking into account absorption of the laser radiation, evaporation process and vapor flow dynamics. The developed solver is validated against available experimental and numerical data for the ethanol and water droplet heating and evaporation. For continuous heating the peak temperature is established by the balance of cooling, evaporation and heating and results in high temperature for larger droplets. It has been shown that for heating by a single laser pulse the maximum temperature of droplets depends only on the peak intensity of the laser radiation. Furthermore, for the peak irradiance close to the transition to the boiling regime, temporal dynamics of the droplet temperature is independent of the droplet size. With proper normalization of time, the dynamics of the droplet shrinkage and cooling is shown to be independent of droplet sizes and peak laser intensities. The influence of cooling and evaporation processes on droplet heating was found to be controlled by the pulse repetition rate for repeated pulse operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Modeling the Effects of Microwave Heating on Densification in Chemical Vapor Infiltration

Microwave heating has great potential to accelerate the synthesis of ceramic matrix composites (CMCs) by a process called Chemical Vapor Infiltration (CVI). In CVI, reactive gases ingress a porous preform and undergo chemical transformation to deposit solid ceramic phase within the pores at high temperature thus, densifying the preform. However, the competing effects of chemical kinetics and gas transport are known to result in non-uniform densification as the outer surfaces of the preform experience faster depositions compared to the core. Achieving spatial temperature control plays a key role improving the densification quality. Microwave heating can potentially create temperature inversion such that the core of the preform is hotter than the outer surface and subsequently, lead to improved densification while keeping the manufacturing times and costs low. In the present work, a computational modeling strategy has been developed that accounts for the key physical phenomena responsible for densification of porous preforms using microwave heating. Specifically, a chemical kinetics model has been formulated for Silicon Carbide (SiC) deposition from MTS/H2 precursor. The model is implemented in a pore-resolved reactive transport solver, Quilt. The CVI simulations are performed for several conditions. Initially, parameterized temperature control is imposed to identify optimum conditions for good densification quality at a fraction of processing time. Further, simulations of microwave heating of porous SiC preforms are performed using OpenFOAM. A strategy to achieve and enhance temperature inversion is identified. The resulting temperature profiles are used in the pore-resolved densification simulations to analyze the densification behavior. It is observed that the temperature inversion achieved by microwave heating leads to significant improvements in densification quality and at the same time, keeps the manufacturing time low.

36 MATERIALS SCIENCE↗

DOE OSTI2022

High Fidelity CFD Simulations Supporting the KP-FHR

Kairos Power, LLC, is developing its version of the Fluoride-cooled High-temperature Reactor, the KP-FHR. The design uses a pebble bed core with fluoride salt as a coolant. The pebbles used in the KP-FHR have a diameter of 4 cm, with a shell fuel region where TRISO particles are embedded. A Pebble bed core design is adopted by several Gen IV reactors, They boast many benefits, such as fuel integrity, highly efficient heat transfer, and passive safety. However, it is challenging to accurately predict temperature and flow inside a pebble bed. Traditional approaches use the porous media model, which regards the pebble bed as a continuous medium, but with different temperature fields representing different levels, such as the fluid temperature, pebble surface temperature, and pebble center temperature. Empirical heat transfer correlations are adopted to calculate the heat transfer coefficient between different phases. However, empirical correlations are usually validated with experimental data, which usually lacks detail inside the pebble bed. The available experimental data is also generally at a high Reynolds number, which falls outside of the conditions of KP-FHR. Explicit computational fluid dynamics (CFD) simulations of randomly packed pebble beds have only become feasible recently. This is thanks to the rapid development of computational power and scalable algorithms. In this work, we used the Spectral Element Method (SEM) CFD code NekRS to simulate the randomly packed pebble bed in a cylindrical container. NekRS, which is the GPU variant of Nek5000, but refactored to utilize the computational power of GPUs using the OCCA library to run on hybrid architecture high performance computing systems. It was initially developed with the libParamunal library, but truncated and tuned for large-scale turbulence simulation. As a result, the SEM reaches higher precision with the same degrees of freedom by using a high-order Lagrange polynomial basis distributed on Gauss-Lobatto-Legendre quadrature inside each element, compared to lower-order methods, such the Finite Volume Method and Finite Element Method. The report is divided into five parts. We start with a general discussion of the pebble bed reactor, along with a specific investigation into the KP-FHR. The second part presents the numerical methodology. In the third part, we study a modular pebble bed with 1741 pebbles in a container of 7 pebble-diameter radius. Beyond LES simulations done by NekRS, we also leveraged the thermal radiation model in OpenFOAM to study heat transfer under no-forced-flow scenarios. Then, in the fourth part we simulated a pebble bed similar to the size of the Hermes Test Reactor. The total number of pebbles is in these simulations is 34,374. The container radius is 14 pebble-diameters. Finally, the report concludes in part five, with a discussion of future work.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2024

Assessing Critical Conditions for Scour Near Obstructions using Bed Shear, Particle Onset of Motion Balances, and CFD-DEM Modeling of Granular Beds

Computational Fluid Dynamics combined with a Discrete Element Method is one of the computational methods that can be used to model multiphase flows. In this method various phases, gas and liquid or solid, are present in the same computational domain. The local averaged Navier–Stokes equations determine the flow of the continuous phase fluid and are solved using the traditional CFD finite volume approach. DEM is based on a Lagrangian formulation, which solves the equations of motion, expressed in ordinary differential equations, for representative particles as they move in space and time. The interactions between the continuous fluid phase and discrete solid phase are modeled with the use of Newton’s laws of motion via drag force. The particles interact with each other and with the boundaries of the fluid continuum, and the resulting contact forces are included in the equations of motion. The properties of solid particles and boundaries are treated as elastic bodies, with specified density, elastic modulus, and Poisson’s ratio. Particle shapes may vary from single spherical particles to more complex-shaped composite particles. The particles may be introduced into the domain by random or structured injection at a point, surface, or volume, depending on the application. More details on the formulation can be found in the Simcenter STAR-CCM+ User’s Manual and OpenFOAM website.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

Aerodynamic Characterization of 3D Scanned Wind Turbine Blades Using Experimental and Computational Methods

This study presents an aerodynamic characterization of 3D scanned wind turbine blades using both experimental and computational methods. The research was conducted by Gulf Wind Technology and Sandia National Laboratories. The primary objective was to investigate the aerodynamic impacts of leading-edge manufacturing defects on wind turbine blades. The study utilized the Stratasys NEO 800 3D Printer for high-precision manufacturing and the GWT Accelerator Wind Tunnel for experimental testing. Computational simulations were performed using COMSOL Multiphysics to model the wind tunnel and analyze flow characteristics and OpenFOAM to study the aerodynamic impacts of leading-edge defects. OpenFAST was used to estimate how these defects can lead to revenue losses for wind farm operators as high as 6%. The results demonstrated significant aerodynamic performance variations due to defects, with detailed analysis provided through wind tunnel and CFD data. The findings contribute to the understanding of defect impacts on wind turbine blade performance and offer insights for future design improvements.

17 WIND ENERGY↗

DOE OSTI2025

FY25 Theory and Simulation Performance Target: Development of an integrated modeling framework for fusion reactor design and assessment (Final Report)

This report documents the FY25 Theory and Simulation Performance Target (TSPT) of developing an integrated modeling framework for fusion reactor design and assessment (FREDA). Over Q1-Q4, new capabilities were developed across both plasma and engineering domains and demonstrated on an example representation of a Compact Advanced Tokamak with a Dual Cooled Lead Lithium blanket. This represents a first-of-a-kind demonstration of coupled core-to-wall-to-engineering for a reactor. Self-consistent CESOL workflows were applied to provide core, pedestal, and SOL prediction; new modules were developed for energetic particle stability (FAR3D) and transport (TGLF-EP) analysis; and boundary plasma modeling (SOLPS-ITER, BOUT++/Hermes-3) was expanded to evaluate wall and divertor heat fluxes and interface with engineering thermal analysis. A parameterized CAD tool, TRACER, was expanded to generate medium-fidelity divertor, blanket, and coil geometries; OpenFOAM and Diablo workflows were applied for first-wall and divertor thermal analyses with helium cooling; and reduced-order models were created for high-mass-flux divertor cooling. Magnet multiphysics capabilities were verified between Elmer, Diablo, and a new MFEM-based solver, and workflows enable stress, thermal, and neutron-fluence analysis of TF coils with neutronics-driven heating. Nuclear and blanket analysis workflows were demonstrated, including tritium breeding, transport, and CFD-informed thermo-mechanical assessment. Preliminary multi-fidelity uncertainty quantification workflows were applied to boundary modeling codes and shown to achieve variance reductions with fewer high-fidelity boundary simulations. Key findings highlight the challenges of resolving the ITEP gap to find suitable balance between wall and divertor loads, neutron heating, and practical limits of PFC cooling. Next step priorities are to develop automated workflows to check boundary code convergence and detachment, implement tighter physics-engineering CAD provenance tracking, and inclusion of plasma-material interface models for SLAG and tungsten cracking behavior. Collectively, these developments establish sophisticated capabilities for predictive, multi-fidelity, whole-device modeling that integrates plasma physics, materials, magnets, and nuclear engineering to guide pathways to viable Fusion Pilot Plant design points.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Q3 Report for FY25 Theory and Simulation Performance Target: Development of an integrated modeling framework for fusion reactor design and assessment

This report describes the work and activities carried out towards the completion of each of the following milestones in FY25 Q3: 1. Demonstrate workflow for generating self-consistent CESOL plasma profiles + first wall and divertor loading prediction and generate the CAT plasma and neutron loading needed for further engineering analysis. • Benchmark between two first wall heat flux mapping methods, identify importance of various heat flux sources and physics impact of using fully coupled CESOL vs post-analysis evaluation. 2. Generate medium fidelity parametrized CAD. • Generate parametrized CAD components for the CAT example case via either user-defined modules called within the geometry generation or by defeatured/parametrized CAD, including DCLL blanket matched to divertor boundary and magnets. Define materials, labels, and boundary conditions for passing the mesh to CFD tools. 3. Demonstrate multiphysics magnet analysis. • Demonstrate magnet analysis workflow called from the FREDA workflow, and 4. Demonstrate nuclear analysis. • Add model to OpenFOAM and/or other codes possibly including Diablo to account for tritium diffusion in solids.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Q2 Report for FY25 Theory and Simulation Performance Target: Development of an integrated modeling framework for fusion reactor design and assessment

This report describes the work and activities carried out towards the completion of each of the following milestones in FY25 Q2: 1. Demonstrate workflow for generating self-consistent CESOL plasma profiles + first wall and divertor loading prediction and generate the CAT plasma and neutron loading needed for further engineering analysis: $\circ$ Run CESOL with BOUT++/Hermes-3 and immersed boundary condition to directly map to wall: • Run BOUT++/Hermes-3 through the IPS workflow to find radial particle and energy diffusivities to match either the Eich or the physics-based scaling of the SOL heat flux width, and • Expand source of first wall heat flux to include charged particles, neutrals, and radiation from the core+edge. 2. Generate medium fidelity parametrized CAD: $\circ$ Develop the TRACER tool to read an existing CAD, regenerate the geometry based on vertex location and connectivity information, define vertex translation and parameters needed for scaling the CAD, and $\circ$ Utilize the FreeGS code to determine CAT PF coil placement, including minimizing the number of coils, coil current, and electromechanical stresses. 3. Utilize plasma loading for engineering analysis: $\circ$ Couple the plasma loading to input for OpenFOAM and demonstrate initial test of thermal analysis of CAT first wall loading with typical DCLL blanket component cooling boundary conditions. 4. Demonstrate nuclear analysis: $\circ$ Apply initial analysis of tritium transport in DCLL blanket by evaluating spatially resolved tritium generation rates, tritium diffusion and convection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Understanding Uncertainty in Microstructure Evolution and Constitutive Properties in Additive Process Modeling

Coupled process–microstructure–property modeling, and understanding the sources of uncertainty and their propagation toward error in part property prediction, are key steps toward full utilization of additive manufacturing (AM) for predictable quality part development. The OpenFOAM model for process conditions, the ExaCA model for as-solidified grain structure, and the ExaConstit model for constitutive mechanical properties are used as part of the ExaAM modeling framework to examine a few of the various sources of uncertainty in the modeling workflow. In addition to “random” uncertainty (due to random number generation in the orientations and locations of grains present), the heterogeneous nucleation density N 0 and the mean substrate grain spacing S 0 are varied to examine their impact of grain area development as a function of build height in the simulated microstructure. While mean grain area after 1 mm of build is found to be sensitive to N 0 and S 0 , particularly at small N 0 and large S 0 (despite some convergence toward similar values), the resulting grain shapes and overall textures develop in a reasonably similar manner. As a result of these similar textures, ExaConstit simulation using ExaCA representative volume elements (RVEs) from various permutations of N 0 , S 0 , and location within the build resulted in similar yield stress, stress–strain curve shape, and stress triaxiality distributions. It is concluded that for this particular material and scan pattern, 15 layers is sufficient for ExaCA texture and ExaConstit predicted properties to become relatively independent of additional layer simulation, provided that reasonable estimates for N 0 and S 0 are used. However, additional layers of ExaCA will need to be run to obtain mean grain areas independent of build height and baseplate structure.

36 MATERIALS SCIENCE↗

DOE OSTI2022

On the Response of a Herschel–Bulkley Fluid Due to a Moving Plate

In this paper, we study the boundary-layer flow of a Herschel–Bulkley fluid due to a moving plate; this problem has been experimentally investigated by others, where the fluid was assumed to be Carbopol, which has similar properties to cement. The computational fluid dynamics finite volume method from the open-source toolbox/library OpenFOAM is used on structured quad grids to solve the mass and the linear momentum conservation equations using the solver “overInterDyMFoam” customized with non-Newtonian viscosity libraries. The governing equations are solved numerically by using regularization methods in the context of the overset meshing technique. The results indicate that there is a good comparison between the experimental data and the simulations. The boundary layer thicknesses are predicted within the uncertainties of the measurements. The simulations indicate strong sensitivities to the rheological properties of the fluid.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Midfidelity model verification for a point-absorbing wave energy converter with linear power take-off

In the preliminary design stage of a wave energy converter (WEC), researchers need fast and reliable simulation tools. High-fidelity numerical models are usually employed to study the wave-structure interaction, but the computational cost is demanding. As an alternative, midfidelity models can provide simulations in the order of real time. In this study, we operate Uppsala University’s WEC in a relatively mild sea state and model it using WEC-Sim. The model is verified based on OpenFOAM simulations. To analyze the ability of the midfidelity model to capture WEC dynamics, we investigate the system separately with 1, 2, and 3 degrees of freedom. We examine the contribution of viscous phenomena, and study both linear and weakly nonlinear solutions provided by WEC-Sim. Our results indicate that the viscous effects can be neglected in heave and surge motion, but not for pitch. We also find that the weakly nonlinear WEC-Sim solution successfully agrees with the computational fluid dynamics, whereas the linear solution could suggest misleading results.

16 TIDAL AND WAVE POWER↗

DOE OSTI2022

Modeling the small-scale deposition of snow onto structured Arctic sea ice during a MOSAiC storm using snowBedFoam 1.0.

The remoteness and extreme conditions of the Arctic make it a very difficult environment to investigate. In these polar regions covered by sea ice, the wind is relatively strong due to the absence of obstructions and redistributes a large part of the deposited snow mass, which complicates estimates for precipitation hardly distinguishable from blowing or drifting snow. Moreover, the snow mass balance in the sea ice system is still poorly understood, notably due to the complex structure of its surface. Quantitatively assessing the snow distribution on sea ice and its connection to the sea ice surface features is an important step to remove the snow mass balance uncertainties (i.e., snow transport contribution) in the Arctic environment. In this work we introduce snowBedFoam 1.0., a physics-based snow transport model implemented in the open-source fluid dynamics software OpenFOAM. We combine the numerical simulations with terrestrial laser scan observations of surface dynamics to simulate snow deposition in a MOSAiC (Multidisciplinary Drifting Observatory for the Study of Arctic Climate) sea ice domain with a complicated structure typical for pressure ridges. The results demonstrate that a large fraction of snow accumulates in their vicinity, which compares favorably against scanner measurements. However, the approximations imposed by the numerical framework, together with potential measurement errors (precipitation), give rise to quantitative inaccuracies, which should be addressed in future work. The modeling of snow distribution on sea ice should help to better constrain precipitation estimates and more generally assess and predict snow and ice dynamics in the Arctic.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

Alquimia v1.0: a generic interface to biogeochemical codes – a tool for interoperable development, prototyping and benchmarking for multiphysics simulators

Alquimia v1.0 is a generic interface to geochemical solvers that facilitates development of multiphysics simulators by enabling code coupling, prototyping and benchmarking. The interface enforces the function arguments and their types for setting up, solving, serving up output data and carrying out other common auxiliary tasks while providing a set of structures for data transfer between the multiphysics code driving the simulation and the geochemical solver. Alquimia relies on a single-cell approach that permits operator splitting coupling and parallel computation. We describe the implementation in Alquimia of two widely used open-source codes that perform geochemical calculations: PFLOTRAN and CrunchFlow. We then exemplify its use for the implementation and simulation of reactive transport in porous media by two open-source flow and transport simulators: Amanzi and ParFlow. We also demonstrate its use for the simulation of coupled processes in novel multiphysics applications including the effect of multiphase flow on reaction rates at the pore scale with OpenFOAM, the role of complex biogeochemical processes in land surface models such as the E3SM Land Model (ELM) and the impact of surface–subsurface hydrological interactions on hydrogeochemical export from watersheds with the Advanced Terrestrial Simulator (ATS). These applications make it apparent that the availability of a well-defined yet flexible interface has the potential to improve the software development workflow, freeing up resources to focus on advances in process models and mechanistic understanding of coupled problems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

DEDFOAM

High-fidelity simulations of directed energy deposition in the OpenFOAM framework.

Kincaid, Kellis [Oak Ridge National Laboratory (OR↗

DOE OSTI2023

AdditiveFOAM

AdditiveFOAM is a continuum heat transfer and fluid flow code for metal additive manufacturing developed on the OpenFOAM CFD Framework. The main components of AdditiveFOAM include: a dynamic heat source model representing heat input from independently moving beams; a robust and efficient thermodynamic solver for solid-liquid phase change in metal alloys; a library to export thermal data to ExaCA— a cellular automata (CA) code used for predicting solidification grain growth. By integrating these capabilities, AdditiveFOAM offers valuable insights into the process-structure relationships of metal additive manufacturing components.

Coleman, John [Oak Ridge National Laboratory (ORNL↗

NASA NTRS2012

Performance of Reynolds Averaged Navier-Stokes Models in Predicting Separated Flows: Study of the Hump Flow Model Problem

Separation can be seen in most aerodynamic flows, but accurate prediction of separated flows is still a challenging problem for computational fluid dynamics (CFD) tools. The behavior of several Reynolds Averaged Navier-Stokes (RANS) models in predicting the separated ow over a wall-mounted hump is studied. The strengths and weaknesses of the most popular RANS models (Spalart-Allmaras, k-epsilon, k-omega, k-omega-SST) are evaluated using the open source software OpenFOAM. The hump ow modeled in this work has been documented in the 2004 CFD Validation Workshop on Synthetic Jets and Turbulent Separation Control. Only the baseline case is treated; the slot flow control cases are not considered in this paper. Particular attention is given to predicting the size of the recirculation bubble, the position of the reattachment point, and the velocity profiles downstream of the hump.

Cappelli, Daniele↗