Search NASA⌕ Search

SEARCH · Search NASA

Results for “optical characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Nonlinear optical characterization of ZnS thin film synthesized by chemical spray pyrolysis method

ZnS thin film was prepared by Chemical Spray Pyrolysis (CSP) method. The sample was characterized by X-ray diffraction method and Z scan technique. XRD pattern showed that ZnS thin film has hexagonal structure with an average size of about 5.6nm. The nonlinear optical properties of ZnS thin film was studied by open aperture Z-Scan technique using Q-switched Nd-Yag Laser at 532nm. The Z-scan plot showed that the investigated ZnS thin film has saturable absorption behavior. The nonlinear absorption coefficient and saturation intensity were also estimated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Steady state and time resolved optical characterization studies of Zn 2 SnO 4 nanowires for solar cell applications

Nanowires are a promising option for sensitized solar cells, sensors, and display technology. Most of the work thus far has focused on binary oxides for these nanowires, but ternary oxides have advantages in additional control of optical and electronic properties. Here, we report on the diffuse reflectance, Low Temperature and Room Temperature Photoluminescence (PL), PL excitation spectrum, and Time Resolved PL (TRPL) of Zinc Tin Oxide (ZTO) nanowires grown by Chemical Vapor Deposition. The PL from the ZTO nanowires does not exhibit any band gap or near gap emission, and the diffuse reflectance measurement confirms that these ZTO nanowires have a direct forbidden transition. The broad PL spectrum reveals two Gaussian peaks centered at 1.86 eV (red) and 2.81 eV (blue), representing two distinct defect states or complexes. The PL spectra were further studied by the Time Resolved Emission Spectrum and intensity dependent PL and TRPL. The time resolved measurements show complex non-exponential decays at all wavelengths, indicative of defect to defect transitions, and the red emissive states decay much slower than the blue emissive states. The effects of annealing in air and vacuum are studied to investigate the origin of the defect states in the nanowires, showing that the blue states are related to oxygen vacancies. We propose an energy band model for the nanowires containing defect states within the band gap and the associated transitions between these states that are consistent with our measurements.

36 MATERIALS SCIENCE↗

Optical Characterization of the Structural Imperfection of Two-Dimensional MoS{sub 2} Crystallites

Two-dimensional molybdenum disulfide crystallites grown by mechanical exfoliation and chemical vapor deposition have been studied. It is shown that both methods can be used to obtain individual crystallites with a monoatomic thickness and similar optical properties. It is found that crystallites grown by chemical vapor deposition have a higher defect concentration than those grown by mechanical exfoliation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

MapX: 2D XRF for Planetary Exploration - Image Formation and Optic Characterization

Map-X is a planetary instrument concept for 2D X-Ray Fluorescence (XRF) spectroscopy. The instrument is placed directly on the surface of an object and held in a fixed position during the measurement. The formation of XRF images on the CCD detector relies on a multichannel optic configured for 1:1 imaging and can be analyzed through the point spread function (PSF) of the optic. The PSF can be directly measured using a micron-sized monochromatic X-ray source in place of the sample. Such PSF measurements were carried out at the Stanford Synchrotron and are compared with ray tracing simulations. It is shown that artifacts are introduced by the periodicity of the PSF at the channel scale and the proximity of the CCD pixel size and the optic channel size. A strategy of sub-channel random moves was used to cancel out these artifacts and provide a clean experimental PSF directly usable for XRF image deconvolution.

47 OTHER INSTRUMENTATION↗

Optical Materials, Adhesive and Encapsulant, III-V, and Optical Characterization Evaluation: Cooperative Research and Development (Final Report)

SolFocus is currently developing solar technology for utility scale application using Winston collector based concentrating photovoltaics (CPV). Part of that technology development includes small mirror dishes and front surface reflectors, and bonding the separate parts to the assembly. Mirror panels must meet rigid optical specifications in terms of radius of curvature, slope errors and specularity. The reflective surfaces must demonstrate long term durability and maintain high reflectivity. Some bonded surfaces must maintain adhesion and transparency under high concentrations and high temperatures. Others will experience moderate temperatures and do not require transparency. NREL researchers have developed methods and tools that address these related areas.

14 SOLAR ENERGY↗

Structural and optical characterization of high-quality ZnO thin films deposited by reactive RF magnetron sputtering

Highlights: ► High-quality ZnO thin films were deposited at room temperature. ► Effect of O{sub 2} flow and RF sputtering voltages on properties of ZnO films were studied. ► O{sub 2}/Ar ratios played a key role in controlling optical properties of ZnO films. ► Photoluminescence intensity of the ZnO films strongly depended on O{sub 2}/Ar ratios. ► Crystallite size, stress and strain strongly depended on O{sub 2}/Ar ratios. - Abstract: ZnO thin films were deposited onto quartz substrates by radio frequency (RF) reactive magnetron sputtering using a Zn target. The structural and optical properties of the ZnO thin films were investigated comprehensively by X-ray diffraction (XRD), ultraviolet–visible and photoluminescence (PL) measurements. The effects of the oxygen content of the total oxygen–argon mixture and sputtering voltage in the sputtering process on the structural and optical properties of the ZnO films were studied systemically. The microstructural parameters, such as the lattice constant, crystallite size, stress and strain, were also calculated and correlated with the structural and optical properties of the ZnO films. In addition, the results showed that the crystalline quality of ZnO thin films improved with increasing O{sub 2}/Ar gas flow ratio from 2:8 to 8:2. XRD and PL spectroscopy revealed 800 V to be the most appropriate sputtering voltage for ZnO thin film growth. High-quality ZnO films with a good crystalline structure, tunable optical band gap as well as high transmittance could be fabricated easily by RF reactive magnetron sputtering, paving the way to obtaining cost-effective ZnO thin films transparent conducting oxides for optoelectronics applications.

36 MATERIALS SCIENCE↗

Structural and optical characterizations of chemically deposited cadmium selenide thin films

Highlights: {yields} CdSe thin films deposited first time using formic acid as a complexing agent. {yields} The deposited thin films were characterized by XRD, SEM, UV-vis-NIR and electrical techniques. {yields} X-ray diffraction analysis shows presence of zinc blende crystal structure. -- Abstract: Synthesis of cadmium selenide thin films by CBD method has been presented. The deposited film samples were subjected to XRD, SEM, UV-vis-NIR and TEP characterization. X-ray diffraction analysis showed that CdSe film sample crystallized in zinc blende or cubic phase structure. SEM studies reveal that the grains are spherical in shape and uniformly distributed all over the surface of the substrates. The optical band gap energy of as deposited film sample was found to be in the order of 1.8 eV. The electrical conductivity of the film sample was found to be 10{sup -6} ({Omega} cm){sup -1} with n-type of conduction mechanism.

36 MATERIALS SCIENCE↗

Optical Characterization and 2,525 micron Lasing of Cr(2+):Cd(0.85)Mn(0.15)Te

Transition metal doped solids are of significant current interest for the development of tunable solid-state lasers for the near and mid-infrared (1-4 pm) spectral region. Applications of these lasers include basic research in atomic, molecular, and solid-state physics, optical communication, medicine, and environmental studies of the atmosphere. In transition metal based laser materials, absorption and emission of light arises from electronic transitions between crystal field split energy levels of 3d transition metal ions. The optical spectra generally exhibit broad bands due to the strong interaction between dopant and host (electron-phonon coupling). Broad emission bands offer the prospect of tunable laser activity over a wide wavelength range, e.g. the tuning range of Ti:Sapphire extends from 700-1100 run. The only current transition metal laser operating in the mid-infrared wavelength region (1.8-2.4 micro-m) is CO(2+):MgF2, but its performance is severely limited due to strong nonradiative decay at room temperature. Based on lifetime data, the quantum efficiency is estimated to be less than 3 deg/0 11,21. In general, the probability for non-radiative decay via multi-phonon relaxation increases with decreasing energy gap between ground and excited state. Therefore, efficient transition metal lasers beyond -1.6 micro-m are rare. Recently, tunable laser activity around 2.3 micro-m was observed from Cr doped ZnS and ZnSe. The new lasing center in these materials was identified as Cr(2+) occupying the tetrahedral Zn site. Tetrahedrally coordinated optical centers are rather unusual among transition metal lasers. Their potential usefulness, however, has been demonstrated by the recent development of near infrared laser materials such as Cr:forsterite and Cr:YAG, which are based on tetrahedrally coordinated Cr(4+) ions. According to the Laporte selection rule, electric-dipole transition within the optically active 3d-electron shells are parity forbidden. However, a static acentric electric crystal field or the coupling of asymmetric phonons can force electric-dipole transitions by the admixture of wave functions with opposite parity. Tetrahedral sites lack inversion symmetry which provides the odd-parity field necessary to relax the parity selection rule. Therefore, high absorption and emission cross sections are observed. An enhanced radiative emission rate is also expected to reduce the detrimental effect of non-radiative decay. Motivated by the initial results on Cr doped ZnS and ZnSe, we have started a comprehensive effort to study Cr(2+) doped II-VI semiconductors for solid-state laser applications. In this paper we present the optical properties and the demonstration of mid-infrared lasing from Cr doped Cd(0.85)Mn(0.15)Te.

Davis, V. R.↗

Structural and optical characterization of Er{sup 3+} doped zinc telluroborate glasses for green laser applications

A new series of Erbium doped Zinc telluroborate glasses were prepared by melt quenching technique. The stretching and bending vibrations of the B–O and Te–O bonds in the prepared glass network were explored through Raman spectra. The nature of the metal-ligand bond was determined using optical absorption spectra through Nephelauxetic ratio (β) and Bonding parameter (δ) studies. The Judd-Ofelt (JO) parameters (Ω{sub 2}, Ω{sub 4}, Ω{sub 6}) and the oscillator strengths were calculated following JO theory. The relatively higher Ω{sub 2} values reveal the higher asymmetry nature. The green emission corresponding to the {sup 2}H{sub 11/2}+{sup 4}S{sub 3/2}→{sup 4}I{sub 15/2} transition was observed at around 550 nm and the luminescence quenching occurs beyond 1.0 wt% of Erbium ion concentration. Radiative properties for the 1.0EZTB glass are found to be higher and its suitability towards green laser applications were discussed and reported.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Formation of Cu{sub 2}O and ZnO Crystal Layers by Magnetron Assisted Sputtering and Their Optical Characterization

Copper (I) oxide and zinc oxide films are formed on silicon and glassy quartz substrates by magnetron assisted sputtering. The thickness of the films is tens and hundreds of nanometers. The films are grown at different substrate temperatures and different oxygen pressures in the working chamber. The film samples are studied by the X-ray diffraction technique, scanning electron microscopy, and optical methods. It is established that an increase in the substrate temperature yields a change in the surface morphology of copper (I) oxide films towards the formation of well-pronounced crystallites. The reflectance and Raman spectra suggest that the quality of such films is close to that of bulk Cu{sub 2}O crystals produced by the oxidation of copper. As concerns ZnO films, an increase in the substrate temperature and an increase in the partial oxygen pressure make it possible to produce films, for which a sharp exciton structure is observed in the reflectance spectra and the emission of excitons bound at donors is observed in the luminescence spectra.

36 MATERIALS SCIENCE↗

Structural and optical characterization of InAs nanocrystals deposited by spray pyrolysis

4-5 nm size InAs nanocrystals were prepared by spray pyrolysis technique on glass substrates from alkaline solution containing InCl{sub 3} and As{sub 2}O. X-Ray diffraction and absorption spectra suggested that the deposition conditions (deposition time and temperature) had a profound influence on the structure and thickness of deposited layers. The optical absorption band edges shifted to lower energy when increasing the thickness with respect to the bulk material. The marked blue shift of the optical absorption edge indicated a strong quantum confinement effect in InAs films.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Synthesis, Characterization, Optical Properties, and Electron Paramagnetic Resonance for Nano Zn{sub 0.5}Co{sub 0.5}Fe{sub 2−x}Pr{sub x}O{sub 4}

Nano ferrite samples of type Zn{sub 0.5}Co{sub 0.5}Fe{sub 2−x} Pr{sub x}O{sub 4}, 0 ≤ x ≤ 0.2, were prepared by co-precipitation method for different concentration of Pr ions at a calcination temperature of 823 K. The samples were characterized using x-ray diffraction and transmission electron microscope (TEM), UV spectroscopy, FTIR, and electron paramagnetic resonance (EPR). The increase in concentration of Pr ions shows a significant change in the formed nano ferrite particles size, degree of aggregation, energy band gap, and lattice parameters. X-band (9.24 GHz) EPR spectra at room temperature showed a decrease in the g factor as the Pr content was increased. Furthermore, the variation of the Pr{sup 3+} concentration in the samples led to different aggregation states, ranging from isolated nanoparticles with average crystal size of 28.5 to about 15 nm, as confirmed by x-ray diffraction and high-resolution transmission electron microscopy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Optical characterization of a-As{sub 2}S{sub 3} thin films prepared by magnetron sputtering

It is well known that thermally evaporated a-As{sub 2}S{sub 3} thin films are prone to oxidation when exposed to ambient environment. These As{sub 2}O{sub 3} crystals can have a devastating effect on propagating light by introducing a major source of scattering loss in submicron optically integrated circuits. Magnetron sputtering a-As{sub 2}S{sub 3} not only produces films that have optical properties closer to their equilibrium state like their bulk glass counter parts, the as-deposited films also show no detectable signs of As{sub 2}O{sub 3} crystals in them when they are exposed to the ambient environment. These attributes are unique to a magnetron sputtered a-As{sub 2}S{sub 3} film and are probably caused by the ''photoannealing'' effect from the visible light emitted by the argon plasma during the sputtering process. The optical properties of a magnetron sputtered a-As{sub 2}S{sub 3} film and its propagation loss on a Ti diffused LiNbO{sub 3} waveguide are reported here. The thin film results agree closely with published data on As{sub 2}S{sub 3} bulk glass, and the optical properties of the as-deposited film are found to be closer to its bulk glass values than films made by thermal evaporation and pulsed laser deposition. The TM propagation loss at {lambda}=1.5 {mu}m of the as-deposited a-As{sub 2}S{sub 3} waveguide on Ti:LiNbO{sub 3} was 0.20{+-}0.05 dB/cm.

36 MATERIALS SCIENCE↗

Al{sup 3+} doped V{sub 2}O{sub 5} nanostructure: Synthesis and structural, morphological and optical characterization

Al{sub x}V{sub 2-x}O{sub 5}(x = 0,2mol%) nanorods were synthesized at room temperature by facile surfactant free non-aqueous route. The phase pure orthorhombic structure and nanorods-like morphology have been studied by X-ray diffraction (XRD) and High resolution scanning electron microscopy. EDXS spectrum confirms the purity and presence of Al into V{sub 2}O{sub 5} lattice. Optical absorption from DRS UV-Vis spectra showed the band gap broadening due to quantum confinement effect. The results ensure that the dopant cation (Al{sup 3+}) successfully intercalated with the host cation (V{sup 5+}) and the products are promising for electrochromic and catalytic applications.

36 MATERIALS SCIENCE↗

Structural and optical characterization of In{sub 2}O{sub 3}/PANI nanocomposite prepared by in-situ polymerization

Polyaniline-indium oxide (In{sub 2}O{sub 3}/PANI) nanocomposite have been prepared by in-situ polymerization of aniline and as-synthesized In{sub 2}O{sub 3} nanoparticles. X-ray diffraction (XRD), Transmission electron microscopy (TEM), Fourier transformation infrared (FTIR) and UV/Vis spectroscopy techniques are used to investigate the structural and optical properties of In{sub 2}O{sub 3}/PANI nanocomposite. TEM analysis shows In{sub 2}O{sub 3} nanoparticles are embedded in PANI nanofibers. FTIR spectra show the good interactions between PANI nanofibers and In{sub 2}O{sub 3} nanoparticles. The band gap and electronic transitions in In{sub 2}O{sub 3}/PANI nanocomposite is determined by using UV/Vis spectra.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Optical characterization of thin nickel films on polymer substrates using reflectance difference spectroscopy

We have used reflectance difference spectroscopy (RDS) and its extension, azimuth-dependent RDS (ADRDS), to study the properties of sputtered and evaporated nickel films on biaxially oriented poly(ethylene terephtalate) (PET) films in a roll to roll web-coating process. From the full set of ADRDS spectra we extract and analyze both the intrinsic RDS spectra and the azimuthal orientation of the effective optical anisotropy of the samples. From the latter, contributions to the RDS spectra arising from the nickel layer and the PET substrate with different orientations of the optical eigenaxes can be inferred. We find an attenuation of the characteristic RDS signal of the PET substrate with increasing nickel film thickness which is in good agreement with the theoretical prediction. For film thicknesses above 20 nm another contribution to the RDS signal attributed to the optical anisotropy of the deposited nickel layers can be observed. Its strength depends on the deposition method, and is considerably larger for evaporated films than for sputtered ones. With increasing nickel film thickness, the azimuthal orientation of the sample anisotropy changes from the initial value of the PET substrate by about 20 deg.toward the machine direction of the foil. We demonstrate that RDS is also a valuable tool for inline monitoring in the roll to roll process, as the attenuation of the RDS signal, under proper consideration of the orientation of the effective anisotropy, is a function of the film thickness and characteristic for the deposited material.

36 MATERIALS SCIENCE↗

Quickest ever single-step mechanosynthesis of Cd{sub 0.5}Zn{sub 0.5}S quantum dots: Nanostructure and optical characterizations

Highlights: Black-Right-Pointing-Pointer Cd{sub 0.5}Zn{sub 0.5}S QDs prepared in 30 min by ball-milling elemental Cd, Zn and S powders. Black-Right-Pointing-Pointer Microstructure characterization is made by XRD employing Rietveld method and HRTEM. Black-Right-Pointing-Pointer Stacking faults in QDs are ascertained both from Rietveld analysis and HRTEM images. Black-Right-Pointing-Pointer Presence of both cubic and hexagonal phases is confirmed by XRD and HRTEM. Black-Right-Pointing-Pointer Quantum confinement is ascertained by blue-shift and optical band gap increment. -- Abstract: Multiphase Cd{sub 0.5}Zn{sub 0.5}S quantum dots (QDs) are prepared for the first time in a record minimum time of 30 min by mechanical alloying the stoichiometric mixture of elemental Cd, Zn and S powders at room temperature under Ar. Initially, the hexagonal phase is formed as major one and then gradually transforms to the cubic phase which is formed coherently on the hexagonal lattice with (0 0 2){sub hexagonal}||(1 1 1){sub cubic} mechanism. In the course of milling up to 15 h, the molar ratio of cubic to hexagonal phase becomes {approx}0.7:0.3. Both high resolution transmission electron microscopy (HRTEM) and X-ray microstructure analyses reveal that these QDs are isotropic in nature, their size reduces to {approx}5 nm after 15 h of milling with a very narrow size distribution and they contain a significant amount of stacking and twin faults. These QDs show very distinct quantum confinement effect and their optical band gaps are higher than that of the bulk CdZnS.

36 MATERIALS SCIENCE↗