Search NASA⌕ Search

SEARCH · Search NASA

Results for “organic cathode materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Low-temperature synthesis process of making MgzMxOy, where M is Mn, V or Fe, for manufacture of electrode materials for group II cation-based batteries

Preparation, characterization, and an electrochemical study of Mg 0.1 V 2 O 5 prepared by a novel sol-gel method with no high-temperature post-processing are disclosed. Cyclic voltammetry showed the material to be quasi-reversible, with improved kinetics in an acetonitrile-, relative to a carbonate-, based electrolyte. Galvanostatic test data under a C/10 discharge showed a delivered capacity >250 mAh/g over several cycles. Based on these results, a magnesium anode battery, as disclosed, would yield an average operating voltage ˜3.2 Volts with an energy density ˜800 mWh/g for the cathode material, making the newly synthesized material a viable cathode material for secondary magnesium batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Lithium inventory tracking as a non-destructive battery evaluation and monitoring method

Tracking the active lithium (Li) inventory in an electrode shows the true state of a Li battery, akin to a fuel gauge for an engine. However, non-destructive Li inventory tracking is currently unavailable. Here, in this work, we used the theoretical capacity of a transition metal oxide to convert capacity into a Li inventory analysis. The Li inventory in electrodes was tracked reliably to show how battery formulations and test methods affect performance. Contrary to capacity, Li inventory tracking reveals stoichiometric variations near the electrode–electrolyte interface. Verifiable results rationalized differences in measurements, clarifying and reducing interferences from cell formulations and experimental manipulations. By tracing four variables from formation to end-of-life, we characterize electrode and cell performance with a thermodynamic framework. Accurate rationalization of subtle differences in Li inventory utilization promises precise battery engineering, evaluation, failure analysis and risk mitigation. The method could be applicable from cell design optimization and fabrication to battery management, improving battery performance and reliability.

25 ENERGY STORAGE↗
DOE OSTI2022

Electrochemically Stable High Energy Density Lithium-Sulfur Batteries

Lithium-Sulfur batteries (LSB) have emerged as one of the strong contenders for high energy density rechargeable batteries in the Li-ion battery domain. The LSB system is considered as the most promising to achieve the next milestone in energy density of 500 Wh/kg. However, the LSB system is plagued with problems of polysulfide formation which are soluble in the organic electrolyte leading to loss in capacity and eventual cell failure. The problem is further compounded by dendrite formation on the Li anode during electrochemical cycling leading to puncturing of the separator causing eventual short-circuiting of the cell and consequent heat generation resulting in major safety hazards of flammability of the organic liquid electrolyte and impending explosion. This chapter describes various approaches developed to combat both cathode and anode issues. These involve synthesis and characterization of complex framework materials (CFMs) for confining the polysulfides and sulfur in the LSB cathodes. The CFMs include a CFM host and a coating applied to the CFM host, which includes one or more form of an electronic conductor, a lithium-ion conductor and a functional electrocatalyst for electrocatalytically converting the soluble polysulfides to Li 2 S. Further, sulfur is infiltrated into the CFM host creating a sulfur-carbon linkage serving as effective anchors for trapping the ensuing polysulfides. The systems have been tested in coin cells and pouch cells with metallic Li anodes under lean electrolyte conditions of 3-4 μl/mg of electrolyte (E) to sulfur (S) ratios showing promise and feasibility. New emergent dendrite-free alloys have also been identified to test against pure Li and CFM cathodes in coin cell and pouch cell configurations under lean electrolyte conditions. Results of these studies are described and discussed with thoughts on future directions.

25 ENERGY STORAGE↗
DOE OSTI2022

Garnet solid electrolyte blended LiNi 0.6 Mn 0.2 Co 0.2 O 2 as high-voltage stable cathodes for advanced lithium-ion batteries

Ni-rich LiNi 1-x Co x/2 Mn x/2 O 2 layered materials have been widely adopted as cathodes for current electric vehicles (EVs) due to their high gravimetric and volumetric energy densities. However, their high-voltage instability (e.g., > 4.3 V vsLi ) limited their usable capacities corresponding to about 60 – 70 % of theoretical capacities. The major problems of high-voltage operation stem from instability of Ni 3+/4+ at cathode-electrolyte interphase (CEI) in contact with electrolytes. Here we propose garnet-type Li 6.7 La 3 Zr 1.7 Ta 0.3 O 12 (LLZT) solid-electrolyte-blended LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC) as high-voltage stable cathodes. The LLZT not only passivates the CEI but scavenges protons and moisture in electrolytes. From well-balanced ionic and electronic transport properties, 5 wt% LLZT blended NMC cathodes delivered enhanced electrochemical performances in full-cells. Unlike other complicated coating processes, our proposed solid-electrolyte blending approach can be readily implementable in commercial Li-ion batteries due to its manufacturing friendliness, energy saving, and cost effectiveness.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Tuning the Morphology and Electronic Properties of Single-Crystal LiNi 0.5 Mn 1.5 O 4-δ : Exploring the Influence of LiCl–KCl Molten Salt Flux Composition and Synthesis Temperature

Single-crystal materials have played a unique role in the development of high-performance cathode materials for Li batteries due to their favorable chemomechanical stability. The molten salt synthesis method has become one of the most prominent techniques used to synthesize single-crystal layered and spinel materials. In this work, the molten salt synthesis method is used as a technique to tune both the morphology and Mn 3+ content of high-voltage LiNi 0.5 Mn 1.5 O 4 (LNMO) cathodes. The resulting materials are thoroughly characterized by a suite of analytical techniques, including synchrotron X-ray core-level spectroscopy, which are sensitive to the material properties on multiple length scales. Furthermore, the multidimensional characterization allows us to build a materials library according to the molten salt phase diagram as well as to establish the relationship among synthesis, material properties, and battery performance. The results of this work show that the Mn 3+ content is primarily dependent on the synthesis temperature and increases as the temperature is increased. Additionally, the particle morphology is mostly dependent on the composition of the molten salt flux, which can be tailored to obtain well-defined octahedrons enclosed by (111) facets, plates with predominant ($11\tilde{2}$) facets, irregularly shaped particles, or mixtures of these. The electrochemical measurements indicate that the Mn 3+ content has a larger contribution to the battery performance of LNMO than do morphological characteristics and that a significant amount of Mn 3+ could become detrimental to the battery performance. However, with similar Mn 3+ contents, morphology still plays a role in influencing the battery cycle life and rate performance. The insights of molten salt synthesis parameters on the formation of LNMO, with deconvolution of the roles of Mn 3+ and morphology, are crucial to continuing studies in the rational design of LNMO cathode materials for high-energy Li batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Phloroglucinol–2,6‐Diaminoanthraquinone as a Durable Redox Mediator for Enhancing Conversion Reaction Kinetics in Lithium‐Sulfur Batteries

Abstract Lithium‐sulfur batteries, despite being a promising solution for next‐generation secondary batteries, require substantial efforts to overcome the challenges of sluggish sulfur redox kinetics, polysulfides shuttling, and Li metal instability before achieving practical viability. Conventional strategies that utilize metal catalysts or soluble redox mediators (RMs) are limited by either impractical producing processes or unsatisfactory service life. Herein, an electrochemically active organic material, phloroglucinol – 2,6‐diaminoanthraquinone (PG‐DAAQ) is synthesized through a green and facile polymerization process to better resolve these issues. Serving as an RM at the cathode, PG‐DAAQ exhibits enduring redox activity within the sulfur operating potential window, leading to enhanced redox kinetics and sulfur utilization. Remarkably, even without any metal elements, PG‐DAAQ exhibits an excellent affinity to polysulfides, thereby suppressing the shuttling and facilitating the formation of a more favorable solid‐electrolyte interface to stabilize Li deposition at the anode. As a result, Li‐S cells employing PG‐DAAQ show significantly enhanced cycling and rate performances than the control cells. Even with a low electrolyte‐to‐sulfur ratio of 6, pouch cells with PG‐DAAQ deliver a reversible discharge capacity of 821 mA h g −1 after 100 cycles at a C/10 rate.

Lai, Tianxing↗
DOE OSTI2021

Interfacial layers for solid-state batteries and methods of making same

One or more interfacial layers in contact with a solid-state electrolyte and hybrid electrolyte materials. Interfacial layers comprise inorganic (e.g., metal oxides and soft inorganic materials) or organic materials (e.g., polymer materials, gel materials and ion-conducting liquids). The interfacial layers can improve the electrical properties (e.g., reduce the impedance) of an interface between an a cathode and/or anode and a solid-state electrolyte. The interfacial layers can be used in, for example, solid-state batteries (e.g., solid-state, ion-conducting batteries).

Hu, Liangbing↗
DOE OSTI2021

A high-performance organic cathode customized for sulfide-based all-solid-state batteries

All-solid-state batteries (ASSBs) have become increasingly attractive recently due to their better safety and prospective long-term stability compared with conventional liquid batteries. However, obtaining a sustainable cathode candidate to match the solid electrolyte with regards to operating potential, chemical compatibility, and mechanical property is still an open challenge. In this work, the chemical incompatibility of quinone-based active materials and sulfide-based electrolyte were unveiled for the first time through a heteroconjugate addition reaction mechanism. To develop a quinone cathode customized for sulfide-based ASSBs, poly-(anthraquinonyl sulfide)-graphene (PAQS-G) nanocomposite was reported. The stable polymer framework of PAQS can protect the quinone redox center by preventing nucleophilic attack from sulfide-based solid electrolytes. The graphene additives can ameliorate redox kinetics and improve active material utilization. The PAQS-G cathode exhibited a specific capacity of ~178 mAh g -1 and a high material utilization of ~79%. Excellent cycling stability was achieved with 94 % capacity after 200 cycles in lithium batteries and 95.5 % capacity after 300 cycles in sodium batteries at 0.1C rate, respectively. A promising potential for energy storage applications was demonstrated.

25 ENERGY STORAGE↗
DOE OSTI2021

Valence Effects of Fe Impurity for Recovered LiNi 0.6 Co 0.2 Mn 0.2 O 2 Cathode Materials

Iron impurities are generally included in the obtained leaching liquor solution during the hydrometallurgical recycling method of spent lithium-ion batteries (LIBs) due to the usage of iron in battery casings and machinery parts of recycling equipment, which would definitely affect the physical and electrochemical features of the recovered active materials. In this paper, the effects of iron impurity with different valence states (Fe 2+ and Fe 3+ ) and gradient concentrations (0.2, 1.0, and 5.0 at. %) for the obtained LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NCM622) cathodes are fully studied. It is found that Fe3+ impurity could easily lower the tap density and average size of NCM622 particles and even introduce some impurity phases in the NCM622 structure at high concentration (5.0 at. %), leading to much lower specific capacity, worse rate capability, and cycling performance of the Fe 3+ -based NCM622 cathode. On contrast, with certain concentrations of Fe 2+ impurity (0.2 and 1.0 at. %), the NCM622 cathode material exhibits comparable and much better electrochemical properties compared with the virgin NCM622 materials. Based on these results, the valence of Fe impurity should be considered and controlled as well as its concentration during the recycling process design for spent LIBs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1970

Multilayer screen gives cathode ray tube high contrast

Fabrication method for cathode ray tubes uses low-cost siloxane resin formulations. The resins contain sufficient methyl or phenyl groups for solubility in organic solvents. After vaporization and baking, the polymerized material is stable under vacuum and under temperatures required for tube fabrication.

Bullinger, H.↗
DOE OSTI2022

Hybrid organic light emitting device

An OLED device comprises an anode and a cathode, and at least one graded emissive layer disposed between the anode and the cathode, the graded emissive layer comprising first and second materials, wherein a concentration of the first material increases continuously from an anode side of the graded emissive layer to a cathode side of the graded emissive layer, and a concentration of the second material decreases continuously from the anode side of the graded emissive layer to the cathode side of the graded emissive layer. An OLED device comprising a graded emissive layer and a hybrid white OLED device are also described.

Forrest, Stephen R.↗
DOE OSTI2020

Towards a high-performance garnet-based solid-state Li metal battery: A perspective on recent advances

Garnet-based solid-state Li metal batteries have been widely considered one of the most promising next-generation energy storage systems. However, the performance of these batteries is plagued by various limitations caused by the solid-state electrolyte (SSE). The poor wetting of lithium on the garnet surface diminishes the contact between the anode and electrolyte, leading to extremely high anode interfacial resistance. Similarly, the point-to-point contact between the cathode and electrolyte leads to high impedance on the cathode side. Moreover, although the SSE serves a firm barrier separating the anode and cathode, lithium dendrites can still grow through, causing a short circuit. Lastly, the solid/solid interface cannot be well maintained under cycling at high current density and capacity. Recently, remarkable progress has been achieved in garnet electrolyte to resolve these problems towards the aim of a high-performance solid-state Li metal battery. In this perspective, we highlight various recent advances in the field of garnet-based solid-state battery, including improving the anode/electrolyte interface, lithium dendrite detection, reducing cathode impedance, and electrolyte architecture design.

25 ENERGY STORAGE↗
DOE OSTI2020

Challenges for and Pathways Toward Solid-State Batteries

Solid-state batteries utilizing lithium metal anodes have the potential to enable batteries with a specific energy of >500 Wh/kg and an energy density of >1,500 Wh/L for thousands of cycles. When optimized they will improve the energy efficiency, operating temperature range, sustainability, and safety at a lower cost compared to projections for advanced Li-ion batteries. This improved performance is critical for the widespread adoption of electric vehicles and may enable future applications such as electric aviation. Expectations for solid-state batteries are high, there are significant materials and processing challenges that need to be overcome. Some of these challenges are well known; others are more subtle and are just becoming known. The challenges and their solutions must be clearly identified to realize high-energy solid-state Li metal batteries. In the United States, the U.S. Department of Energy (DOE) funds the majority of energy storage research and development, including solid state battery research. Web of Science publication analysis shows that worldwide DOE is second largest funder. Work on solid state batteries is distributed across different arms of DOE and is coordinated at headquarters to ensure a broad national portfolio for advanced batteries, including lithium batteries and solid-state battery devices. We note that university and national laboratory researchers in the US with a long-standing interest in solid state batteries is a small, integrated community with recognized impact for publications, patents and startup companies. The opportunity for this group to engage for research with international colleagues is growing, fostered by periodic bilateral meetings supported by DOE and by the recent joint US German research program for lithium battery interface studies. These are valuable opportunities to speed solid-state battery development. The ORNL led virtual workshop, overviewed here, confirms the community’s shared vision of the exciting advances, opportunities, and challenges. Further, we are seeing that this workshop has spawned several new informal collaborations and draft proposals. This encourages us to propose future discussion. On May 11, 2020, Oak Ridge National Laboratory (ORNL) hosted a 6-hour, on-line national workshop to discuss recent advances and most the prominent obstacles to realizing solid-state Li metal batteries. The workshop included more than 30+ experts from national laboratories, universities, and companies, all of whom have worked on solid-state batteries for multiple years. The participants shared recent advances, many not yet in print, illustrating that the community has gained significant new insights for solid-state Li battery materials over the last 5 years. In this report, the major outcomes of the workshop are organized to identify the gaps in our scientific knowledge for four core materials science areas: (1) Li metal anodes, (2) the solid electrolyte in contact with Li metal, (3) active cathode materials and solid-state composite cathodes, and (4) solid electrolytes. Illustrative examples and discussions are reported with the more comprehensive issues in the report. Discussion of additional challenges related to processing of solid-state battery materials and to the designs and architectures for mechanically robust, long-lived batteries received less attention due to time constraints. These are good themes for deeper discussion at a follow-on workshop, where a complete list of critical research topics can be identified.

25 ENERGY STORAGE↗
DOE OSTI2022

Understanding Lithium Local Environments in LiMn 0.5 Ni 0.5 O 2 Cathodes: A DFT-Supported 6 Li Solid-State NMR Study

LiMn 0.5 Ni 0.5 O 2 has been plagued by the structural failure driven by the irreversible phase change upon subsequent cycling and the structural degradation caused by the seemingly unavoidable Li/Ni exchange. This begs for a better understanding of the correlation between lithium local structures, synthesis conditions, and overall electrochemical properties of materials. In this study, we use density functional theory (DFT) to assist experimental 6 Li solid-state magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy to understand the nature and change in lithium local structures with extended annealing times (168 vs 15 h) synthesized at 900 °C. To correlate the NMR peak changes after different synthesis conditions, we calculated the NMR spectra of representative low-energy model configurations of LiMn 0.5 Ni 0.5 O 2 composition–zigzag, row, and flower structures–as well as the influence of Ni/Mn ordering and Li/Ni exchange on each spectrum using a supercell that is large enough to allow us to consider the effect of different relative configurations of adjacent transition metal (TM) layers. The analysis based on a combination of the calculated NMR and the experimental spectra suggests that most configurations contributing to the experimental spectra are in fact composed of a blend of configurations higher in energy than the classical well-ordered ground-state structures. Further, the extended annealing of LiMn 0.5 Ni 0.5 O 2 slightly enhances Ni/Mn and Li/Mn orderings while reducing the Li/Ni mixing ratio. This study shows how DFT calculations are crucial in providing a better understanding of the experimental characterization data and therefore local environments and domain structures in oxide materials, such as Li-ion battery cathodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Self-Organization of Plasma-Material Interfaces

The primary goals of the project are a) improve the understanding of transport processes, chemical reactions and plasma-driven self-organization such as stratification and filamentation, formation of anode spots, liquid droplets ejection from cathodes, and plasma electrolysis, b) utilize and share among the project participants computational tools developed by the participants to understand plasma-based surface functionalization and plasma-enabled pattern nucleation in a wide range of scales from nano- to millimeters, and c) use experimental methods and facilities available at the University of Alabama in Huntsville (UAH) and Sandia National Laboratories (SNL) to understand and control plasma processes, reaction pathways and the electric nature of self-organization of the plasma-exposed interface structures.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Tuning Surface Acidity of Mixed Conducting Electrodes: Recovery of Si‐Induced Degradation of Oxygen Exchange Rate and Area Specific Resistance

Abstract Metal oxides are an important class of functional materials, and for many applications, ranging from solid oxide fuel/electrolysis cells, oxygen permeation membranes, and oxygen storage materials to gas sensors (semiconducting and electrolytic) and catalysts, the interaction between the surface and oxygen in the gas phase is central. Ubiquitous Si‐impurities are known to impede this interaction, commonly attributed to the formation of glassy blocking layers on the surface. Here, the surface oxygen exchange coefficient ( k chem ) is examined for Pr 0.1 Ce 0.9 O 2‐δ (PCO), a model mixed ionic electronic conductor, via electrical conductivity relaxation measurements, and the area‐specific resistance (ASR) by electrochemical impedance spectroscopy. It is demonstrated that even low silica levels, introduced by infiltration, depress k chem by a factor 4000, while the ASR increases 40‐fold and we attribute this to its acidity relative to that of PCO. The ability to fully regenerate the poisoned surface by the subsequent addition of basic Ca‐ or Li‐species is further shown. This ability to not only recover Si‐poisoned surfaces by tuning the relative surface acidity of an oxide surface, but subsequently outperform the pre‐poisoned response, promises to extend the operating life of materials and devices for which the catalytic oxygen/solid interface reaction is central.

30 DIRECT ENERGY CONVERSION↗
NASA NTRSDate not supplied

Dry Pressed, High Areal Loading Electrode Architectures Enabled by Holey Graphene

For future electric aviation, advanced battery cell chemistry beyond lithium ion batteries are required to meet mission requirements. High energy density battery concepts such as lithium-sulfur (Li-S) and lithiumoxygen (Li-O2) chemistries are being intensively investigated to realize their extraordinary theoretical promise in terms of energy density. Most fabrication methods of cathodes for these novel battery chemistries followed a conventional approach. In this approach, the active material is mixed with a polymer binder and a conductive carbon in a high-boiling organic solvent to form a slurry, followed by casting onto a current collector and solvent evaporation. The process is usually lengthy and poses environmental hazards due to the use of organic solvents.

Lin Yi↗
DOE OSTI2021

Electrolyte compositions for stabilizing silicon electrodes in lithium batteries

A lithium-ion electrochemical cell comprises a first electrode, a second electrode comprising elemental silicon, a microporous separator membrane between the first and second electrodes, and an electrolyte in contact with the electrodes and the membrane. The electrolyte comprises a lithium salt at a concentration in the range of about 0.1 M to about 5 M, and an additional metal salt at a concentration in the range of about 0.001 to about 5 M dissolved in an organic solvent. The additional metal salt comprises a metal cation that can form a lithium-silicon-metal Zintl phase; and the first electrode comprises metallic lithium or a cathode active material capable of donating and accepting lithium ions to and from the second electrode during electrochemical cycling. Electrolytes for use with silicon-containing electrodes also are described.

Vaughey, John T.↗