Search NASA⌕ Search

SEARCH · Search NASA

Results for “parallel planes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Approximation for Horizontal Photon Transport in Cloud Remote Sensing Problems

The effect of horizontal photon transport within real-world clouds can be of consequence to remote sensing problems based on plane-parallel cloud models. An analytic approximation for the root-mean-square horizontal displacement of reflected and transmitted photons relative to the incident cloud-top location is derived from random walk theory. The resulting formula is a function of the average number of photon scatterings, and particle asymmetry parameter and single scattering albedo. In turn, the average number of scatterings can be determined from efficient adding/doubling radiative transfer procedures. The approximation is applied to liquid water clouds for typical remote sensing solar spectral bands, involving both conservative and non-conservative scattering. Results compare well with Monte Carlo calculations. Though the emphasis is on horizontal photon transport in terrestrial clouds, the derived approximation is applicable to any multiple scattering plane-parallel radiative transfer problem. The complete horizontal transport probability distribution can be described with an analytic distribution specified by the root-mean-square and average displacement values. However, it is shown empirically that the average displacement can be reasonably inferred from the root-mean-square value. An estimate for the horizontal transport distribution can then be made from the root-mean-square photon displacement alone.

Plantnick, Steven↗
NASA NTRS1979

A general and computationally fast formulation for radiative transfer with scattering

A general formulation of monocromatic radiative transfer with scattering has been developed for plane-parallel geometry. The inhomogeneous and nonisothermal medium absorbs, emits, and anisotropically scatters radiation. Surfaces can emit and scatter radiation in any specified manner. The solution procedure uses the fact that phase incoherent scattering is linear in radiative sources. Certain basic scattering functions are then defined and calculated by an adding computer code using matrix algebra. These scattering functions are weighted by the temperature field and summed (superimposed) to obtain the solution for any specific problem. Numerical results for exiting intensities and one-sided heat fluxes from general media bound by one arbitrary surface are presented. These parametric studies demonstrate the effects of scattering particles and surfaces on radiative transfer from inhomogeneous and nonisothermal media. Application of the formulation to radiative equilibrium is also discussed. The conclusion is that all problems in plane-parallel radiative transfer with scattering can be solved by a common and computationally fast algorithm based on this formulation.

Cogley, A. C.↗
NASA NTRS1999

Vertical Photon Transport in Cloud Remote Sensing Problems

Photon transport in plane-parallel, vertically inhomogeneous clouds is investigated and applied to cloud remote sensing techniques that use solar reflectance or transmittance measurements for retrieving droplet effective radius. Transport is couched in terms of weighting functions which approximate the relative contribution of individual layers to the overall retrieval. Two vertical weightings are investigated, including one based on the average number of scatterings encountered by reflected and transmitted photons in any given layer. A simpler vertical weighting based on the maximum penetration of reflected photons proves useful for solar reflectance measurements. These weighting functions are highly dependent on droplet absorption and solar/viewing geometry. A superposition technique, using adding/doubling radiative transfer procedures, is derived to accurately determine both weightings, avoiding time consuming Monte Carlo methods. Superposition calculations are made for a variety of geometries and cloud models, and selected results are compared with Monte Carlo calculations. Effective radius retrievals from modeled vertically inhomogeneous liquid water clouds are then made using the standard near-infrared bands, and compared with size estimates based on the proposed weighting functions. Agreement between the two methods is generally within several tenths of a micrometer, much better than expected retrieval accuracy. Though the emphasis is on photon transport in clouds, the derived weightings can be applied to any multiple scattering plane-parallel radiative transfer problem, including arbitrary combinations of cloud, aerosol, and gas layers.

Platnick, S.↗
NASA NTRS1977

Numerical calculation of the transonic flow past a swept wing

A numerical method is presented for analyzing the transonic potential flow past a lifting, swept wing. A finite difference approximation to the full potential equation is solved in a coordinate system which is nearly conformally mapped from the physical space in planes parallel to the symmetry plane, and reduces the wing surface to a portion of one boundary of the computational grid. A coordinate invariant, rotated difference scheme is used, and the difference equations are solved by relaxation. The method is capable of treating wings of arbitrary planform and dihedral, although approximations in treating the tips and vortex sheet make its accuracy suspect for wings of small aspect ratio. Comparisons of calculated results with experimental data are shown for examples of both conventional and supercritical transport wings. Agreement is good for both types, but it was found necessary to account for the displacement effect of the boundary layer for the supercritical wing, presumably because of its greater sensitivity to changes in effective geometry.

Jameson, A.↗
NASA NTRS1977

Multi-axis hand controller for the shuttle remote manipulator system

The Shuttle Remote Manipulator System, has a articulated arm of 50 ft. length with six motor-driven joints. The basic purpose is to establish physical contact with various space hardware items and maneuver these to the desired position and attitude with respect to the Orbiter, nulling out relative velocities and stabilizing the free-body system by managing residual energies. The normal operating mode is resolved-motion end-point rate control by man-in-loop command. The translational freedoms are defined so that the End Effector (EEFTR) of the arm will move in planes parallel to the principal translational planes of the Orbiter, at a rate commanded by the displacement of the Translation Hand Controller in the corresponding freedom and direction. The rotational freedoms are rate-controlled by the Rotation Hand Controller about pivot axes parallel to Orbiter roll, pitch and yaw, originating at the EEFTR reference point.

Lippay, A. L.↗
NASA NTRS1994

Self-consistent steady state model of the low-latitude boundary layer

Results are presented from a steady state numerical model of the low-latitude boundary layer (LLBL) on closed field lines and its coupling to the dayside auroral ionosphere. In the model the boundary layer approximation is used, the result being that inertial forces are taken into account only in the main flow direction (-x) where they are balanced by pressure forces, j x B forces, and viscous forces. Motion in the transverse directions (y and z) is treated kinematically, the force balances in these two directions being purely static. Computationally, the model is two dimensional, describing the motion of plasma and frozen-in magnetic field in the equatorial (xy) plane but allowing for lowest-order polynomial variation of some quantities with the coordinate (z) perpendicular to that plane. The plasma expands and compresses isentropically; the magnetic field is calculated self-consistently, which leads to approximately parabolic field line shape in planes parallel to the magnetopause (the xz plane), with maximum field curvature near the magnetopause edge of the LLBL. Coupling to the ionosphere via region 1 field-aligned currents is included. The effects of the ionosphere are represented by two parallel resistive plates at fixed height above and below the equatorial plane. The model can be used to investigate the influence of various physical parameters, for example, viscous and magnetic Reynolds numbers, and of boundary conditions at the magnetopause and in the magnetosphere on the LLBL development in the -x direction. Special attention is given to viscous effects which, under suitable circumstances, lead to a region 1 current that first increases and then reduces with increasing longitude away from local noon. Asymptotic matching of the antisunward motion of the cool LLBL plasma to sunward convection of hot plasma in the magnetosphere is illustrated along with the entrainment of magnetospheric plasma by the antisunward LLBL flow.

Drakou, E.↗
NASA NTRSDate not supplied

In-situ Nanoscale Ablation

An understanding of the ablation of carbon-based materials is crucial to modeling the behavior of atmospheric entry spacecrafts equipped with thermal protection systems (TPS).Carbon is the backbone of TPS systems such as PICA (phenolic-impregnated carbon ablator).Therefore in the present work we study ablation of highly oriented pyrolytic graphite (HOPG)in oxygen at temperatures up to 1000°C done within a gas reaction cell housed in a scanning transmission electron microscope (STEM). Observation of the HOPG oxidation on specimens sectioned parallel and normal to the carbon basal planes in the presence of oxygen are reported.Pitting caused by residual oxygen and/or platinum particles from the sectioning process was observed before oxygen gas flow was established at 750°C in the specimen sectioned with the carbon basal planes parallel to the beam direction. Introduction of oxygen flow caused rapid oxidation moving in a uniform front that completely consumed the HOPG in approximately 1.5minutes. The specimen sectioned with the carbon basal planes normal to the beam direction did not show the same pitting phenomenon but exhibited rapid oxidation at 1000°C that proceeded in a uniform front and completed in approximately 1 minute. All specimens tested had a husk resembling the original specimen shape left over after oxidation. It is concluded that this husk is most likely ash impurity from the HOPG or impurities from the sectioning process or E-chip. A residual gas analyszer (RGA) was successfully used to monitor gas flows during the experiments but was yet unsuccessful in monitoring oxidation gas products produced during the experiment.Future studies will optimize the RGA setup in order to maximize the potential for detecting these species. These in-situ studies successfully show how this highly ordered carbon ablates on a nano- and micro-scopic length scale and can be used to provide fundamental understanding of carbon ablation that can be used to design the next-generation of TPS systems.

Nanoscale Ablation↗
NASA NTRS1981

Mixing layer simulation by an improved three-dimensional vortex-in-cell algorithm

An extension is presented of the three-dimensional vortex-in-cell (VIC) method that allows for the simulation of incompressible turbulent flows such as plane mixing layers and wakes with exact boundary conditions in the normal direction. The vorticity is assumed to be confined between two parallel planes and the turbulence is assumed to be homogeneous in the two directions parallel to the planes. As an application, an analysis is presented of the evolution of the plane mixing layer subjected to random two- and three-dimensional initial disturbances.

Couet, B.↗
NASA NTRS2012

Acoustic Measurements of an Uninstalled Spacecraft Cabin Ventilation Fan Prototype

Sound pressure measurements were recorded for a prototype of a spacecraft cabin ventilation fan in a test in the NASA Glenn Acoustical Testing Laboratory. The axial fan is approximately 0.089 m (3.50 in.) in diameter and 0.223 m (9.00 in.) long and has nine rotor blades and eleven stator vanes. At design point of 12,000 rpm, the fan was predicted to produce a flow rate of 0.709 cu m/s (150 cfm) and a total pressure rise of 925 Pa (3.72 in. of water) at 12,000 rpm. While the fan was designed to be part of a ducted atmospheric revitalization system, no attempt was made to throttle the flow or simulate the installed configuration during this test. The fan was operated at six speeds from 6,000 to 13,500 rpm. A 13-microphone traversing array was used to collect sound pressure measurements along two horizontal planes parallel to the flow direction, two vertical planes upstream of the fan inlet and two vertical planes downstream of the fan exhaust. Measurements indicate that sound at blade passing frequency harmonics contribute significantly to the overall audible noise produced by the fan at free delivery conditions.

Fans↗
NASA NTRS2012

Acoustic Measurements of an Uninstalled Spacecraft Cabin Ventilation Fan Prototype

Sound pressure measurements were recorded for a prototype of a spacecraft cabin ventilation fan in a test in the NASA Glenn Acoustical Testing Laboratory. The axial fan is approximately 0.089 m (3.50 in) in diameter and 0.223 m (9.00 in) long and has nine rotor blades and eleven stator vanes. At design point of 12,000 rpm, the fan was predicted to produce a flow rate of 0.0709 m3/s (150 cfm) and a total pressure rise of 925 Pa (3.72 in. of water) at 12,000 rpm. While the fan was designed to be part of a ducted atmospheric revitalization system, no attempt was made to throttle the flow or simulate the installed configuration during this test. The fan was operated at six speeds from 6,000 rpm to 13,500 rpm. A 13-microphone traversing array was used to collect sound pressure measurements along two horizontal planes parallel to the flow direction, two vertical planes upstream of the fan inlet and two vertical planes downstream of the fan exhaust. Measurements indicate that sound at blade passing frequency harmonics contribute significantly to the overall audible noise produced by the fan at free delivery conditions.

fan↗
NASA NTRS1995

Fast Light-Sheet Scanner

Optomechanical apparatus maintains sheet of pulsed laser light perpendicular to reference axis while causing sheet of light to translate in oscillatory fashion along reference axis. Produces illumination for laser velocimeter in which submicrometer particles entrained in flow illuminated and imaged in parallel planes displaced from each other in rapid succession. Selected frequency of oscillation range upward from tens of hertz. Rotating window continuously shifts sheet of light laterally while maintaining sheet parallel to same plane.

Hunter, William W., Jr.↗
NASA NTRS2012

Hybrid Wing Body Shielding Studies Using an Ultrasonic Configurable Fan Artificial Noise Source Generating Simple Modes

An Ultrasonic Configurable Fan Artificial Noise Source (UCFANS) was designed, built, and tested in support of the Langley Research Center s 14- by 22-Foot wind tunnel test of the Hybrid Wing Body (HWB) full three-dimensional 5.8 percent scale model. The UCFANS is a 5.8 percent rapid prototype scale model of a high-bypass turbofan engine that can generate the tonal signature of candidate engines using artificial sources (no flow). The purpose of the test was to provide an estimate of the acoustic shielding benefits possible from mounting the engine on the upper surface of an HWB aircraft and to provide a database for shielding code validation. A range of frequencies, and a parametric study of modes were generated from exhaust and inlet nacelle configurations. Radiated acoustic data were acquired from a traversing linear array of 13 microphones, spanning 36 in. Two planes perpendicular to the axis of the nacelle (in its 0 orientation) and three planes parallel were acquired from the array sweep. In each plane the linear array traversed five sweeps, for a total span of 160 in. acquired. The resolution of the sweep is variable, so that points closer to the model are taken at a higher resolution. Contour plots of Sound Pressure Level, and integrated Power Levels are presented in this paper; as well as the in-duct modal structure.

Sutliff, Daniel, L.↗
NASA NTRS1993

Manufacturing methods for machining spring ends parallel at loaded length

A first end surface of a coiled compression spring at its relaxed length is machined to a plane transverse to the spring axis. The spring is then placed in a press structure having first and second opposed planar support surfaces, with the machined spring end surface bearing against the first support surface, the unmachined spring end surface bearing against a planar first surface of a lateral force compensation member, and an opposite, generally spherically curved surface of the compensation member bearing against the second press structure support surface. The spring is then compressed generally to its loaded length, and a circumferentially spaced series of marks, lying in a plane parallel to the second press structure support surface, are formed on the spring coil on which the second spring end surface lies. The spring is then removed from the press structure, and the second spring end surface is machined to the mark plane. When the spring is subsequently compressed to its loaded length the precisely parallel relationship between the machined spring end surfaces substantially eliminates undesirable lateral deflection of the spring.

Hinke, Patrick Thomas↗
NASA NTRS1995

Manufacturing methods for machining spring ends parallel at loaded length

A first end surface of a coiled compression spring at its relaxed length is machined to a plane transverse to the spring axis. The spring is then placed in a press structure having first and second opposed planar support surfaces, with the machined spring end surface bearing against the first support surface, the unmachined spring end surface bearing against a planar first surface of a lateral force compensation member, and an opposite, generally spherically curved surface of the compensation member bearing against the second press structure support surface. The spring is then compressed generally to its loaded length, and a circumferentially spaced series of marks, lying in a plane parallel to the second press structure support surface, are formed on the spring coil on which the second spring end surface lies. The spring is then removed from the press structure, and the second spring end surface is machined to the mark plane. When the spring is subsequently compressed to its loaded length the precisely parallel relationship between the machined spring end surfaces substantially eliminates undesirable lateral deflection of the spring.

Hinke, Patrick Thomas↗
NASA NTRS2001

Applicability of the single equivalent point dipole model to represent a spatially distributed bio-electrical source

Although the single equivalent point dipole model has been used to represent well-localised bio-electrical sources, in realistic situations the source is distributed. Consequently, position estimates of point dipoles determined by inverse algorithms suffer from systematic error due to the non-exact applicability of the inverse model. In realistic situations, this systematic error cannot be avoided, a limitation that is independent of the complexity of the torso model used. This study quantitatively investigates the intrinsic limitations in the assignment of a location to the equivalent dipole due to distributed electrical source. To simulate arrhythmic activity in the heart, a model of a wave of depolarisation spreading from a focal source over the surface of a spherical shell is used. The activity is represented by a sequence of concentric belt sources (obtained by slicing the shell with a sequence of parallel plane pairs), with constant dipole moment per unit length (circumferentially) directed parallel to the propagation direction. The distributed source is represented by N dipoles at equal arc lengths along the belt. The sum of the dipole potentials is calculated at predefined electrode locations. The inverse problem involves finding a single equivalent point dipole that best reproduces the electrode potentials due to the distributed source. The inverse problem is implemented by minimising the chi2 per degree of freedom. It is found that the trajectory traced by the equivalent dipole is sensitive to the location of the spherical shell relative to the fixed electrodes. It is shown that this trajectory does not coincide with the sequence of geometrical centres of the consecutive belt sources. For distributed sources within a bounded spherical medium, displaced from the sphere's centre by 40% of the sphere's radius, it is found that the error in the equivalent dipole location varies from 3 to 20% for sources with size between 5 and 50% of the sphere's radius. Finally, a method is devised to obtain the size of the distributed source during the cardiac cycle.

NASA Discipline Cardiopulmonary↗
NASA NTRS2004

Cross-Stream PIV Measurements of Jets With Internal Lobed Mixers

With emphasis being placed on enhanced mixing of jet plumes for noise reduction and on predictions of jet noise based upon turbulent kinetic energy, unsteady measurements of jet plumes are a very important part of jet noise studies. Given that hot flows are of most practical interest, optical techniques such as Particle Image Velocimetry (PIV) are applicable. When the flow has strong azimuthal features, such as those generated by chevrons or lobed mixers, traditional PIV, which aligns the measurement plane parallel to the dominant flow direction is very inefficient, requiring many planes of data to be acquired and stacked up to produce the desired flow cross-sections. This paper presents PIV data acquired in a plane normal to the jet axis, directly measuring the cross-stream gradients and features of an internally mixed nozzle operating at aircraft engine flow conditions. These nozzle systems included variations in lobed mixer penetration, lobe count, lobe scalloping, and nozzle length. Several cases validating the accuracy of the PIV data are examined along with examples of its use in answering questions about the jet noise generation processes in these nozzles. Of most interest is the relationship of low frequency aft-directed noise with turbulence kinetic energy and mean velocity.

Bridges, James↗
NASA NTRS2003

Physically Based Failure Criteria for Transverse Matrix Cracking

A criterion for matrix failure of laminated composite plies in transverse tension and in-plane shear is developed by examining the mechanics of transverse matrix crack growth. Matrix cracks are assumed to initiate from manufacturing defects and can propagate within planes parallel to the fiber direction and normal to the ply mid-plane. Fracture mechanics models of cracks in unidirectional laminates, embedded plies and outer plies are developed to determine the onset and direction of propagation for unstable crack growth. The models for each ply configuration relate ply thickness and ply toughness to the corresponding in-situ ply strength. Calculated results for several materials are shown to correlate well with experimental results.

Davila, Carlos G.↗