Results for “passive capture” — Page 5

NASA NTRS2004

Advanced Docking System With Magnetic Initial Capture

An advanced docking system is undergoing development to enable softer, safer docking than was possible when using prior docking systems. This system is intended for original use in docking of visiting spacecraft and berthing the Crew Return Vehicle at the International Space Station (ISS). The system could also be adapted to a variety of other uses in outer space and on Earth, including mating submersible vehicles, assembling structures, and robotic berthing/handling of payloads and cargo. Heretofore, two large spacecraft have been docked by causing the spacecraft to approach each other at a speed sufficient to activate capture latches - a procedure that results in large docking loads and is made more difficult because of the speed. The basic design and mode of operation of the present advanced docking system would eliminate the need to rely on speed of approach to activate capture latches, thereby making it possible to reduce approach speed and thus docking loads substantially. The system would comprise an active subsystem on one spacecraft and a passive subsystem on another spacecraft with which the active subsystem will be docked. The passive subsystem would include an extensible ring containing magnetic striker plates and guide petals. The active subsystem would include mating guide petals and electromagnets containing limit switches and would be arranged to mate with the magnetic striker plates and guide petals of the passive assembly. The electromagnets would be carried on (but not rigidly attached to) a structural ring that would be instrumented with load sensors. The outputs of the sensors would be sent, along with position information, as feedback to an electronic control subsystem. The system would also include electromechanical actuators that would extend or retract the ring upon command by the control subsystem.

Lewis, James L.↗

NASA NTRSDate not supplied

The Comet Astrobiology Exploration Sample Return (CAESAR) Mission

The Comet Astrobiology Exploration Sample Return (CAESAR) mission will acquire and return to Earth for laboratory analysis a minimum of 80 grams of surface material from the nucleus of comet 67P/Chur-yumov-Gerasimenko (67P). CAESAR will characterize the surface region sampled, preserve the collected sample in a pristine state, and return evolved volatiles by capturing them in a separate gas reservoir. NASA Goddard Space Flight Center provides project management, systems engineering, safety and mission assurance, contamination control, mission operations, and many other important functions. Northrop Grumman Space Systems will build the spacecraft, based on Dawn mission heritage, which like CAESAR, uses solar electric propulsion. CAESAR was selected by for Phase A study in the New Frontiers 4 Competition and will be proposed to New Frontiers 5.Collection of a sample from the surface of comet 67P is facilitated by a set of cameras that together provide images to support sample site selection, perform optical navigation, and document the sample before, during, and after col-lection. The sample is collected at the end of an arm during a 5-second touch-and-go (TAG) maneuver with the Sample Acquisition System (SAS)designed by Honeybee Robotics for the surface properties of comet 67P observed by the Rosetta mission. After sample collection, and while the sample is still cold (< -80°C), the TAG Arm inserts the sample container into the Sample Containment System (SCS) mounted inside the Sample Return Capsule (SRC). The SCS is sealed, preventing the sample from escaping into space. The sample is slowly warmed inside the SCS to enable sublimation of volatiles, which are collected in the Gas Containment System (GCS), a passively cooled gas reservoir. Separating the volatiles from the solid sample protects the solid sample from alteration. Once all sublimated H2O is transferred to the GCS, the GCS is sealed to capture the volatile sit contains, and the SCS is vented to space to maintain the solid sample under vacuum. The SCS vent is closed before Earth entry to prevent atmospheric contamination. Detailed laboratory analyses of the sample from 67P will trace the history of volatile reservoirs, delineate the chemical pathways that led from simple interstellar species to complex molecules, constrain the evolution of the comet, and evaluate the role of comets in delivering water and prebiotic organics to the early Earth. CAESAR will achieve these goals by carrying out coordinated sample analyses that will link macroscopic properties of the comet with microscale mineralogy, chemistry, and isotopic studies of volatiles and solids. Most of the sample (≥75%) will be set aside for analyses by generations of scientists using continually advancing tools and methods, yielding an enduring scientific treasure that only sample return can provide. This presentation will review development conducted during NF4 Phase A and discuss the NF5 mission concept.

A G Hayes↗

NASA NTRS1992

The LDCE Particle Impact Experiment as flown on STS-46

Many materials and techniques have been developed by the authors to sample the flux of particles in Low Earth Orbit (LEO). Though regular in-site sampling of the flux in LEO the materials and techniques have produced data which compliment the data now being amassed by the Long Duration Exposure Facility (LDEF) research activities. Orbital debris models have not been able to describe the flux of particles with d sub p less than or = 0.05 cm, because of the lack of data. Even though LDEF will provide a much needed baseline flux measurement, the continuous monitoring of micron and sub-micron size particles must be carried out. A flight experiment was conducted on the Space Shuttle as part of the LDCE payload to develop an understanding of the Spatial Density (concentration) as a function of size (mass) for particle sizes 1 x 10(exp 6) cm and larger. In addition to the enumeration of particle impacts, it is the intent of the experiment that hypervelocity particles be captured and returned intact. Measurements will be performed post flight to determine the flux density, diameters, and subsequent effects on various optical, thermal control and structural materials. In addition to these principal measurements, the Particle Impact Experiment (PIE) also provides a structure and sample holders for the exposure of passive material samples to the space environment, e.g., thermal cycling, and atomic oxygen, etc. The experiment will measure the optical property changes of mirrors and will provide the fluence of the ambient atomic oxygen environment to other payload experimenters. In order to augment the amount of material returned in a form which can be analyzed, the survivability of the experiment as well as the captured particles will be assessed. Using Sandia National Laboratory's hydrodynamic computer code CTH, hypervelocity impacts on the materials which comprise the experiments have been investigated and the progress of these studies are reported.

Maag, Carl R.↗

NASA NTRS1992

Method and apparatus for preloading a joint by remotely operable means

The invention is a method and apparatus for joining structures, an active structure and a passive structure, and imposing a tensile pre-load on the joint by a remotely operable mechanism comprising a heat contractible joining element. The method and apparatus include mounting on the structure, a probe shaft of material which is transformable from an expanded length to a contracted length when heated to a specific temperature range. The shaft is provided with a probe head which is receivable in a receptacle opening formed in the passive structure, when the active structure is moved into engagement therewith by an appropriate manipulator mechanism. A latching system mounted on the structure adjacent to the receptacle opening captures the probe head, when the probe head is inserted a predetermined amount. A heating coil on the shaft is energizable by remote control for heating the shaft to a temperature range which transforms the shaft to its contracted length, whereby a latching shoulder thereof engages latching elements of the latching system and imposes a tensile preload on the structural joint. Provision is also made for manually adjusting the probe head on the shaft to allow for manual detachment of the structures or manual preloading of the structural joint.

Shelton, Robert O.↗

NASA NTRS1993

Method and apparatus for preloading a joint by remotely operable means

The invention is a method and apparatus for joining structures, an active structure and a passive structure, and imposing a tensile pre-load on the joint by a remotely operable mechanism comprising a heat contractible joining element. The method and apparatus include mounting on the structure, a probe shaft of material which is transformable from an expanded length to a contracted length when heated to a specific temperature range. The shaft is provided with a probe head which is receivable in a receptacle opening formed in the passive structure, when the active structure is moved into engagement therewith by an appropriate manipulator mechanism. A latching system mounted on the structure adjacent to the receptacle opening captures the probe head, when the probe head is inserted a predetermined amount. A heating coil on the shaft is energizable by remote control for heating the shaft to a temperature range which transforms the shaft to its contracted length, whereby a latching shoulder thereof engages latching elements of the latching system and imposes a tensile preload on the structural joint. Provision is also made for manually adjusting the probe head on the shaft to allow for manual detachment of the structures or manual preloading of the structural joint.

Kahn, Jon B.↗

NASA NTRS1992

Development of a machine vision system for automated structural assembly

Research is being conducted at the LaRC to develop a telerobotic assembly system designed to construct large space truss structures. This research program was initiated within the past several years, and a ground-based test-bed was developed to evaluate and expand the state of the art. Test-bed operations currently use predetermined ('taught') points for truss structural assembly. Total dependence on the use of taught points for joint receptacle capture and strut installation is neither robust nor reliable enough for space operations. Therefore, a machine vision sensor guidance system is being developed to locate and guide the robot to a passive target mounted on the truss joint receptacle. The vision system hardware includes a miniature video camera, passive targets mounted on the joint receptacles, target illumination hardware, and an image processing system. Discrimination of the target from background clutter is accomplished through standard digital processing techniques. Once the target is identified, a pose estimation algorithm is invoked to determine the location, in three-dimensional space, of the target relative to the robots end-effector. Preliminary test results of the vision system in the Automated Structural Assembly Laboratory with a range of lighting and background conditions indicate that it is fully capable of successfully identifying joint receptacle targets throughout the required operational range. Controlled optical bench test results indicate that the system can also provide the pose estimation accuracy to define the target position.

Sydow, P. Daniel↗

NASA NTRS1994

Arctic sea ice concentrations from special sensor microwave imager and advanced very high resolution radiometer satellite data

Nearly coincident data from the special sensor microwave imager (SSM/I) and the advanced very high resolution radiometer (AVHRR) are used to compute and compare Arctic sea ice concentrations for different regions and times of the year. To help determine overall accuracies and to highlight sources of differences between passive microwave, optical wavelength, and thermal wavelength data, ice concentrations are estimated using two operational SSM/I ice concentration algorithms and with visible- and thermal-infrared wavelength AVHRR data. All algorithms capture the seasonal patterns of ice growth and melt. The ranges of differences fall within the general levels of uncertainty expected for each method and are similar to previous accuracy estimates. The estimated ice concentrations are all highly correlated, with uniform biases, although differences between individual pairs of observations can be large. On average, the NASA Team algorithm yielded 5% higher ice concentrations than the Bootstrap algorithm, while during nonmelt periods the two SSM/I algorithms agree to within 0.5%. These seasonal differences are consistent with the ways that the 19-GHz and 37-GHz microwave channels are used in the algorithms. When compared to the AVHRR-derived ice concentrations, the Team-algorithm results are more similar on average in terms of correlation and mean differences. However, the Team algorithm underestimates concentrations relative to the AVHRR output by 6% during cold months and overestimates by 3% during summer. Little seasonal difference exists between the Bootstrap and AVHRR results, with a mean difference of about 5%. Although the mean differences are less between the SSM/I-derived concentrations and concentrations estimated using AVHRR channel 1, the correlations appear substantially better between the SSM/I data and concentrations derived from AVHRR channel 4, particularly for the Team algorithm output.

Emery, W. J.↗

NASA NTRS2010

Reactive Sequencing for Autonomous Navigation Evolving from Phoenix Entry, Descent, and Landing

Virtual Machine Language (VML) is an award-winning advanced procedural sequencing language in use on NASA deep-space missions since 1997, and was used for the successful entry, descent, and landing (EDL) of the Phoenix spacecraft onto the surface of Mars. Phoenix EDL utilized a state-oriented operations architecture which executed within the constraints of the existing VML 2.0 flight capability, compatible with the linear "land or die" nature of the mission. The intricacies of Phoenix EDL included the planned discarding of portions of the vehicle, the complex communications management for relay through on-orbit assets, the presence of temporally indeterminate physical events, and the need to rapidly catch up four days of sequencing should a reboot of the spacecraft flight computer occur shortly before atmospheric entry. These formidable operational challenges led to new techniques for packaging and coordinating reusable sequences called blocks using one-way synchronization via VML sequencing global variable events. The coordinated blocks acted as an ensemble to land the spacecraft, while individually managing various elements in as simple a fashion as possible. This paper outlines prototype VML 2.1 flight capabilities that have evolved from the one-way synchronization techniques in order to implement even more ambitious autonomous mission capabilities. Target missions for these new capabilities include autonomous touch-and-go sampling of cometary and asteroidal bodies, lunar landing of robotic missions, and ultimately landing of crewed lunar vehicles. Close proximity guidance, navigation, and control operations, on-orbit rendezvous, and descent and landing events featured in these missions require elaborate abort capability, manifesting highly non-linear scenarios that are so complex as to overtax traditional sequencing, or even the sort of one-way coordinated sequencing used during EDL. Foreseeing advanced command and control needs for small body and lunar landing guidance, navigation and control scenarios, work began three years ago on substantial upgrades to VML that are now being exercised in scenarios for lunar landing and comet/asteroid rendezvous. The advanced state-based approach includes coordinated state transition machines with distributed decision-making logic. These state machines are not merely sequences - they are reactive logic constructs capable of autonomous decision making within a well-defined domain. Combined with the JPL's AutoNav software used on Deep Space 1 and Deep Impact, the system allows spacecraft to autonomously navigate to an unmapped surface, soft-contact, and either land or ascend. The state machine architecture enabled by VML 2.1 has successfully performed sampling missions and lunar descent missions in a simulated environment, and is progressing toward flight capability. The authors are also investigating using the VML 2.1 flight director architecture to perform autonomous activities like rendezvous with a passive hypothetical Mars sample return capsule. The approach being pursued is similar to the touch-and-go sampling state machines, with the added complications associated with the search for, physical capture of, and securing of a separate spacecraft. Complications include optically finding and tracking the Orbiting Sample Capsule (OSC), keeping the OSC illuminated, making orbital adjustments, and physically capturing the OSC. Other applications could include autonomous science collection and fault compensation.

asteroid↗

NASA NTRS1994

Main characteristics of the COMET/COMRADE experiments

Both the COMET (Collection en Orbite de Matiere Extra Terrestre) and the COMRADE (Collection of Micrometeorites, Residue and Debris Ejecta) programs are developed to the collection and analysis of the particles of various origins orbiting around the Earth at low altitudes (between approx. 300 and approx. 500 km). The COMET experiment is more specifically designed to be flown for a short period of time (a few days), in concordance with a meteor stream crossing the Earth. Thus, it results in a considerable enrichment in the collection of grains related to a given comet. The COMRADE experiment has been selected as a proposal for long-duration flights (a few months), in order to gain information on all sizes of particles present on low Earth orbits, including submicrometer grains. It has been accepted by ESA authorities for use on the EURECA 2 platform. The objectives of these studies are multiple. The use of passive detectors gives access to the chemical and isotopical properties of the grains in the micrometer size range, by analyzing either the particle remnant mixed with the target material, or the intact particle captured in a specific low-density material. The particle remnants of the micrometer-sized extraterrestrial grains, having impacted on purposely designed metallic collectors, are identified for complete and detailed chemical, isotopic, and organic analysis, thereby determining grain composition as well as the existence of organic and inorganic molecules, to be related with the possible cometary origin of the grains. Micrometer/submicrometer dust grains are also captured in a manner that ensures minimal particle degradation. The captured intact particles are returned to Earth for complete and detailed chemical, isotopic, spectral, mineralogical, and organic analysis.

Borg, J.↗

NASA NTRS2010

Quick Attach Docking Interface for Lunar Electric Rover

The NASA Lunar Electric Rover (LER) has been developed at Johnson Space Center as a next generation mobility platform. Based upon a twelve wheel omni-directional chassis with active suspension the LER introduces a number of novel capabilities for lunar exploration in both manned and unmanned scenarios. Besides being the primary vehicle for astronauts on the lunar surface, LER will perform tasks such as lunar regolith handling (to include dozing, grading, and excavation), equipment transport, and science operations. In an effort to support these additional tasks a team at the Kennedy Space Center has produced a universal attachment interface for LER known as the Quick Attach. The Quick Attach is a compact system that has been retro-fitted to the rear of the LER giving it the ability to dock and undock on the fly with various implements. The Quick Attach utilizes a two stage docking approach; the first is a mechanical mate which aligns and latches a passive set of hooks on an implement with an actuated cam surface on LER. The mechanical stage is tolerant to misalignment between the implement and the LER during docking and once the implement is captured a preload is applied to ensure a positive lock. The second stage is an umbilical connection which consists of a dust resistant enclosure housing a compliant mechanism that is optionally actuated to mate electrical and fluid connections for suitable implements. The Quick Attach system was designed with the largest foreseen input loads considered including excavation operations and large mass utility attachments. The Quick Attach system was demonstrated at the Desert Research And Technology Studies (D-RA TS) field test in Flagstaff, AZ along with the lightweight dozer blade LANCE. The LANCE blade is the first implement to utilize the Quick Attach interface and demonstrated the tolerance, speed, and strength of the system in a lunar analog environment.

Schuler, Jason M.↗

NASA NTRS2004

Advanced Video Guidance Sensor Development Testing

NASA's Marshall Space Flight Center was the driving force behind the development of the Advanced Video Guidance Sensor, an active sensor system that provides near-range sensor data as part of an automatic rendezvous and docking system. The sensor determines the relative positions and attitudes between the active sensor and the passive target at ranges up to 300 meters. The VGS uses laser diodes to illuminate retro-reflectors in the target, a solid-state camera to detect the return from the target, and image capture electronics and a digital signal processor to convert the video information into the relative positions and attitudes. This development effort has required a great deal of testing of various sorts at every phase of development, and some of the test efforts, predictions, and results will be laid out in this paper.

Howard, Richard T.↗

NASA NTRS2004

Advanced Video Guidance Sensor (AVGS) Development Testing

NASA's Marshall Space Flight Center was the driving force behind the development of the Advanced Video Guidance Sensor, an active sensor system that provides near-range sensor data as part of an automatic rendezvous and docking system. The sensor determines the relative positions and attitudes between the active sensor and the passive target at ranges up to 300 meters. The AVGS uses laser diodes to illuminate retro-reflectors in the target, a solid-state camera to detect the return from the target, and image capture electronics and a digital signal processor to convert the video information into the relative positions and attitudes. The AVGS will fly as part of the Demonstration of Autonomous Rendezvous Technologies (DART) in October, 2004. This development effort has required a great deal of testing of various sorts at every phase of development. Some of the test efforts included optical characterization of performance with the intended target, thermal vacuum testing, performance tests in long range vacuum facilities, EMI/EMC tests, and performance testing in dynamic situations. The sensor has been shown to track a target at ranges of up to 300 meters, both in vacuum and ambient conditions, to survive and operate during the thermal vacuum cycling specific to the DART mission, to handle EM1 well, and to perform well in dynamic situations.

Howard, Richard T.↗

NASA NTRSDate not supplied

Design for an Integrated Open-Loop System for Carbon Dioxide Removal using Liquid Amine

Manned Space missions require maintaining a safe environment for the crew that can both sustain a breathable atmosphere and remove pollutants. Carbon dioxide, while not toxic in low concentrations, accumulates as crew members work and breath and can eventually affect the crew’s health. Therefore, a constant, passive system to remove the carbon dioxide build up is necessary for long-term missions. Currently, the prevailing liquid sorbent used in submarines and industrial flue gas utilizes the primary amine, monoethanolamine (MEA), to capture, transfer, and remove carbon dioxide from air. Diglycolamine (DGA) is an alternate primary amine that has similar performance and less volatility. It is currently being studied at Ames Research Center (ARC) and is the primary candidate for the operation of the sub-scale liquid amine test stand. The test stand is used to investigate liquid flow and liquid gas interfaces to assist in a system design for microgravity applications. The test stand includes a wedge design utilizes capillary action to hold the liquid while allowing gas-liquid interaction for carbon dioxide transfer. These wedge trays are placed in a contactor unit to remove carbon dioxide from the air stream, a degasser unit to replenish the liquid amine, and a capillary condensing heat exchanger (CCHX) to recapture water lost in the degasser unit. Nominal operating conditions for the contactor are a gas flow rate of 26scfm enriched with pure CO2 to 2600ppm and a liquid mixture of 65/35 vol% DGA/H2O at 0.65mL/min while the degasser was operated at 100°C and 1 atm. This paper discusses the challenges and limitations of a fully integrated system which will influence the design of a new subscale test stand.

Adrian Cortez↗

NASA NTRS2005

Simulation and ground testing with the Advanced Video Guidance Sensor

The Advanced Video Guidance Sensor (AVGS), an active sensor system that provides near-range 6-degree-of-freedom sensor data, has been developed as part of an automatic rendezvous and docking system for the Demonstration of Autonomous Rendezvous Technology (DART). The sensor determines the relative positions and attitudes between the active sensor and the passive target at ranges up to 300 meters. The AVGS uses laser diodes to illuminate retro-reflectors in the target, a solid-state imager to detect the light returned from the target, and image capture electronics and a digital signal processor to convert the video information into the relative positions and attitudes. The development of the sensor, through initial prototypes, final prototypes, and three flight units, has required a great deal of testing at every phase, and the different types of testing, their effectiveness, and their results, are presented in this paper, focusing on the testing of the flight units. Testing has improved the sensor's performance.

Howard, Richard T.↗

NASA NTRSDate not supplied

Simulation of Etch Pit Formation in DSMC Through Active Sites in Carbon Fiber Micro-Structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation because of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gases such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various detailed surface reaction mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRSDate not supplied

DSMC Simulation of Etch Pit Formation Through Active Sites in Carbon Fiber Micro-Structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation because of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gases such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various detailed surface reaction mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRS2022

Vulnerability of Passive Microwave Snowfall Retrievals to Physical Properties of Snowpack: A Perspective from Dense Media Radiative Transfer Theory

The uncertainty of passive microwave retrievals of snowfall is notoriously high where the high-frequency surface emissivity is significantly reduced and varies markedly in response to changes of snowpack physical properties. Using the dense media radiative transfer theory, this article studies the potential effects of terrestrial snow-cover depth, density, and6grain size on high-frequency channels 89 and 166 GHz of the radiometer onboard the Global Precipitation Measurement (GPM) core satellite, which are commonly used to capture the snowfall scattering signals. Integrating the inference across all feasible grain sizes, ranges of snowpack density and depth are identified over which the snowfall scattering signatures can be time varying and potentially obscured. Using 10 years of reanalysis data, the seasonal vulnerability of snowfall retrievals to changes of snowpack emissivity in the Northern Hemisphere is mapped in a probabilistic sense and connections are made with uncertainties of the GPM passive microwave snowfall retrievals. It is found that among different snow classes, relatively light Arctic tundra snow in fall, with a density below 260kg m−3, and shallow prairie snow during the winter, with a depth of less than 40cm, can reduce the surface emissivity and obscure the snowfall passive microwave signatures. It is demonstrated that, during the winter, the highly vulnerable areas are over Kazakhstan, and Mongolia with taiga and prairie snow. In the fall, these areas are largely over tundra and taiga snow in north of Russia and the Arctic Archipelagos as well as prairies in Canada and the Great Plains in the United States.

Reyhaneh Rahimi↗

NASA NTRS1990

Asymmetric supersonic flow around cones with noncircular sections

The unsteady, compressible, single and double thin-layer, Navier-Stokes equations are used to solve for steady and unsteady, asymmetric, supersonic flow around pointed bodies with noncircular sections at high incidence and zero side slip. The equations are solved by using an implicit, upwind, flux-difference splitting finite-volume scheme. Since the flow is locally conical, the solutions are presented on a cross-flow plane at the axial station of unit. The grid is generated by using a modified Joukowski transformation. The computational applications cover noncircular sections with elliptic and diamond shapes. Unsteady asymmetric vortex shedding has been captured at large angles of attack. It is shown that for the same flow conditions and same cross-section fineness ratio, the diamond-section cones develop less flow asymmetry than the elliptic-section cones. Passive control of flow asymmetry was also demonstrated computationally.

Kandil, Osama A.↗