Search NASA⌕ Search

SEARCH · Search NASA

Results for “performance improvements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

On the mechanism of performance improvement of electroactive polyvinyl chloride (PVC) gel actuators via conductive fillers

Abstract The electromechanical actuation of transparent plasticized polyvinyl chloride (PVC) gels with conductive fillers were studied. The effects of functionalized carbon nanotubes (CNTs) and 1-butyl-3-methylimidazolium tetrafluoroborate ([Bmim]BF 4 ) ionic liquid (IL) on both the electrical conduction and dielectric processes within PVC gels were investigated, and the differences between the two were clarified. Both CNTs and IL were shown to increase the conductivity of the gels and produce larger electromechanical transduction of a contraction actuator, but only CNTs were shown to increase the electrostatic adhesion force of the PVC gels. The addition of charge carriers to the gel via the inclusion of ILs was shown to significantly reduce the conductivity relaxation time, and the transient current upon voltage polarity reversal indicated multiple peaks corresponding to the introduction of carriers with different polarities and mobilities into the gel. This is believed to cause a screening effect, reducing the charge accumulation at the anode that is the foundational basis for PVC gels’ actuation mechanism. A recommendation for preferable conductive fillers for various applications is made.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Improving Performance of Tape Restore Request Scheduling in the Storage System dCache

Given the anticipated increase in the amount of scientific data, it is widely accepted that primarily disk based storage will become prohibitively expensive. Tape based storage, on the other hand, provides a viable and affordable solution for the ever increasing demand for storage space. Coupled with a disk caching layer that temporarily holds a small fraction of the total data volume to allow for low latency access, it turns tape based systems into active archival storage (write once, read many) that imposes additional demands on data flow optimization compared to traditional backup setups (write once, read never). In order to preserve the lifetime of tapes and minimize the inherently higher access latency, different tape usage strategies are being evaluated. As an important disk storage system for scientific data that transparently handles tape access, dCache is making efforts to evaluate its recall optimization potential and is introducing a proof-of-concept, high-level stage request scheduling component within its SRM implementation.

Morschel, Lea↗
DOE OSTI2020

Optimizing the Super H-mode pedestal to improve performance and facilitate divertor integration

Access to Super H-mode is demonstrated for moderately shaped plasmas in agreement with EPED predictions. In particular, Super H-mode is realized in a DIII-D shape that is accessible to the JET tokamak. The reduced triangularity of the JET-compatible shape compared to previous Super H-mode plasma shapes does not prevent deep ascension into the so-called Super H-mode “channel”. Operationally, access is enabled and optimized by a delaying the neutral beam power injection and thus protracting the L-H transition. In highly shaped DIII-D plasmas, the injection of nitrogen sufficient for the establishment of a radiative divertor by is shown to be possible during Super H-mode without pedestal degradation. Here, due to its increased stored energy and radiative divertor integration capabilities, the Super H-mode is a promising candidate as operating regime for JET, ITER and future fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Comprehensive model for evaluating voltage losses and performance improvements in thin-film photovoltaic devices

Progress of state-of-the-art and next-generation thin-film photovoltaic devices is often stymied by open-circuit voltage (𝑉 oc ) that is significantly lower than theoretical and practical limits. Yet, effectively diagnosing the primary sources of voltage loss remains challenging. Herein, a sequence of device-level characterization techniques and simulations are employed to identify and rank loss mechanisms. For the research-based Cd⁡(Se,Te) device under study, most of the loss was at the front semiconductor heterointerface due to a clifflike conduction-band offset that lowered the recombination activation energy. Additional losses due to band tails were quantified by photoluminescence analysis. The latter provided the absorption coefficient and activation energy reduction associated with band tails as inputs to device models. Simulations showed that alleviating front-interface issues would improve 𝑉 oc , but it would then be limited by bulk recombination. Further improvement of the bulk would then lead to back-contact limitations. Reducing band tails is beneficial in any circumstance. In conclusion, this analysis provides guidance for reaching toward the radiative 𝑉 oc limit.

14 SOLAR ENERGY↗
DOE OSTI2023

Improving Performance of III-V Solar Cells Grown on Spalled Germanium with Ex Situ Substrate Planarization

Controlled spalling allows removal of devices and provides an opportunity for cost reduction through substrate reuse. However, the fracture-based process can leave behind morphological surface features, notably river lines, that can disrupt epitaxial growth and degrade device performance. We investigate the viability of various wet etch chemistries to planarize river lines to ensure high-quality device growth and performance without mechanical repolishing, and so maintain a route towards cost-effective reuse. Etching in a HF: HNO 3 :CH 3 COOH solution effectively planarizes river lines and produces a surface that yields devices with equivalent performance to those grown on epi-ready Ge wafer surfaces. Further studies will focus on optimizing etch composition, temperature, and time to minimize material removal while maintaining a suitable surface for high-quality epitaxy.

germanium↗
DOE OSTI2022

Facile Surface Coatings for Performance Improvement of NMC811 Battery Cathode Material

High nickel content layered oxide LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) is a promising cathode material with a high theoretical capacity of 200 mAh g -1 for use in high energy density lithium-ion batteries. However, its surface can easily get passivated by LiOH and Li 2 CO 3 due to its surface residual Li 2 O being reacting with ambient moisture and CO 2 . Herein, NMC811 was treated in a 3.0 M solution of lithium bis(fluorosulfonyl)imide (LiFSI) in dimethyl carbonate (DMC) at 60 °C for 8 h, 16 h and 24 h, respectively, resulting in coating of the NMC811 surface with LiF due to the basic nature of those residual lithium salts that react with LiFSI. The facile treatment of NMC811 in LiFSI/DMC not only improves the cycling stability but also enhances the capacity of the Li/NMC811 cells, mainly because of the thinning of the Li 2 CO 3 layer as suggested by cyclic voltammograms and impedance analyses. This method opens a new avenue for activation of passivated NMC811 particles for practical battery applications.

25 ENERGY STORAGE↗