Search NASA⌕ Search

SEARCH · Search NASA

Results for “photovoltaic modules”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Some tradeoffs in ingot shaping and price of solar photovoltaic modules

Growth of round ingots is cost-effective for sheets but leaves unused space when round cells are packed into a module. This reduces the packing efficiency, which approaches 95% for square cells, to about 78% and reduces the conversion efficiency of the module by the same ratio. Shaping these ingots into squares with regrowth of cut silicon improves the packing factor, but increases growth cost. The cost impact on solar cell modules was determined by considering shaping ingots in stages from full round to complete square. The sequence of module production with relevant price allocation guidelines is outlined. The severe penalties in add-on price due to increasing slice thickness and kerf are presented. Trade-offs between advantages of recycling silicon and shaping costs are developed for different slicing scenarios. It is shown that shaping results in cost saving of up to 21% for a 15 cm dia. ingot.

Daud, T.↗
NASA NTRS1981

Photovoltaic module hot spot durability design and test methods

As part of the Jet Propulsion Laboratory's Low-Cost Solar Array Project, the susceptibility of fat-plate modules to hot-spot problems is investigated. Hot-spot problems arise in modules when the cells become back-biased and operate in the negative-voltage quadrant, as a result of short-circuit current mismatch, cell cracking or shadowing. The details of a qualification test for determining the capability of modules of surviving field hot-spot problems and typical results of this test are presented. In addition, recommended circuit-design techniques for improving the module and array reliability with respect to hot-spot problems are presented.

Arnett, J. C.↗
NASA NTRS1984

Edge Supports for Photovoltaic Modules

Mounting strips patterned after glazing gaskets. Easy to install supports for rooftop solar modules consist of extruded rubber mullions with locking zippers. Supports cut to length with utility knife and installed without special tools. Adaptable to many different roof configurations.

Maloney, T. J.↗
NASA NTRS1982

Photovoltaic Module Encapsulation Design and Materials Selection, Volume 1, Abridged

A summary version of Volume 1, presenting the basic encapsulation systems, their purposes and requirements, and the characteristics of the most promising candidate systems and materials, as identified and evaluated by the Flat-Plate Solar Array Project is presented. In this summary version considerable detail and much supporting and experimental information has necessarily been omitted. A reader interested in references and literature citations, and in more detailed information on specific topics, should consult Reference 1, JPL Document No. 5101-177, JPL Publication 81-102, DOE/JPL-1012-60 (JPL), June 1, 1982.

Cuddihy, E. F.↗
NASA NTRS1982

Advanced Czochralski silicon growth technology for photovoltaic modules

Several economic analyses had indicated that large-diameter, multiple ingot growth using a single crucible with melt replenishment would be required for Cz growth to be economically viable. Based on the results of these analyses, two liquid and two solid feed melt replenishment approaches were initiated. The sequential solid feed melt replenishment approach, which demonstrated elements of technical feasibility is described in detail in this paper. Growth results of multiple ingots (10-cm-diameter, totaling 100 kg; and 15-cm-diameter, totaling 150 kg weight per crucible) are presented. Solar cells were fabricated and analyzed to evaluate the effects of structure and chemical purities as a result of multiple growth. The results indicate that, with semiconductor-grade silicon, feedstock impurity build-up does not seem to degrade cell performance. For polycrystalline cells, the average efficiencies are 15 to 25% lower than those of single crystalline cells. Concerns regarding single crystal yields, crucible quality and growth speed are indicated, and present status and future research thrusts are also discussed.

Daud, T.↗
NASA NTRS1983

Hermetic edge sealing of photovoltaic modules

The edge sealing technique is accomplished by a combination of a chemical bond between glass and aluminum, formed by electrostatic bonding, and a metallurgical bond between aluminum and aluminum, formed by ultrasonic welding. Such a glass to metal seal promises to provide a low cost, long lifetime, highly effective hermetic seal which can protect module components from severe environments. Development of the sealing techniques and demonstration of their effectiveness by fabricating a small number of dummy modules, up to eight inches square in size, and testing them for hermeticity using helium leak testing methods are reviewed. Non-destructive test methods are investigated.

Source record↗
NASA NTRS1983

Hermetic edge sealing of photovoltaic modules

The feasibility of using an electrostatic bonding (ESB) and ultrasonic welding process to produce hermetic edge seals on terrestrial solar cell modules was investigated. The fabrication sequence is to attach an aluminum foil "gasket' to the perimeter of a glass sheet. A cell circuit is next encapsulated inside the gasket, and its aluminum foil back cover is seam welded ultrasonically to the gasket. An ESB process for sealing aluminum to glass was developed in an ambient air atmosphere, which eliminates the requirement for a vacuum or pressure vessel. An ultrasonic seam welding process was also developed which did not degrade the quality of the ESB seal. Good quality welds with minimal deformation were produced. The effectiveness of the above described sealing techniques was tested by constructing 400 sq cm (8 x 8 s64 sq in) sample modules, and then subjecting them to nondestructive fine and gross leak tests. The gross leak tests identified several different causes of leaks which were then eliminated by modifying the assembly process.

Nowlan, M. J.↗
NASA NTRS1983

Photovoltaic module bypass diode encapsulation

The design and processing techniques necessary to incorporate bypass diodes within the module encapsulant are presented. The Semicon PN junction diode cells were selected. Diode junction to heat spreader thermal resistance measurements, performed on a variety of mounted diode chip types and sizes, have yielded values which are consistently below 1 deg C per watt, but show some instability when thermally cycled over the temperature range from -40 to 150 deg C. Three representative experimental modules, each incorporating integral bypass diode/heat spreader assemblies of various sizes, were designed. Thermal testing of these modules enabled the formulation of a recommended heat spreader plate sizing relationship. The production cost of three encapsulated bypass diode/heat spreader assemblies were compared with similarly rated externally mounted packaged diodes. It is concluded that, when proper designed and installed, these bypass diode devices will improve the overall reliability of a terrestrial array over a 20 year design lifetime.

Shepard, N. J., Jr.↗
NASA NTRS1982

Empirical testing of structural deflection modeling of large photovoltaic modules

The objective of the structural deflection test was to verify the analytical models used to predict solar cell stress, load-bearing layer stress, and module deflection that result from a uniform pressure load on the module surface. The verification process consisted of measuring module deflection, stress in the solar cell, and stress in the load-bearing member as a functon of normal pressure load, pottant modulus of elasticity, pottant thickness, and cell location. Four glass superstrate modules, two plain wood substrate modules, two ribbed wood substrate modules, and a steel substrate module were tested. Consistent with analysis predictions, all unribbed specimens exhibited nonlinear load vs. deflection characteristics. With the exception of the steel module, test results and analysis predictions for panel deflectons agreed to within 10 percent. A wider variation of agreement was found for stress in the load-bearing members and cells.

Duncan, L. B.↗
NASA NTRS1984

Solar-cell interconnect design for terrestrial photovoltaic modules

Useful solar cell interconnect reliability design and life prediction algorithms are presented, together with experimental data indicating that the classical strain cycle (fatigue) curve for the interconnect material does not account for the statistical scatter that is required in reliability predictions. This shortcoming is presently addressed by fitting a functional form to experimental cumulative interconnect failure rate data, which thereby yields statistical fatigue curves enabling not only the prediction of cumulative interconnect failures during the design life of an array field, but also the quantitative interpretation of data from accelerated thermal cycling tests. Optimal interconnect cost reliability design algorithms are also derived which may allow the minimization of energy cost over the design life of the array field.

Mon, G. R.↗
NASA NTRS1984

Flammability of photovoltaic modules

A series of Class B burning-brand tests were performed on experimental modules using high-temperature, back-surface materials to develop the technology base required to construct fire-ratable modules. Results indicate the existence of synergistic relationships between hydrocarbon encapsulation materials and the experimental module configurations that provide increased fire resistance. These configurations use Kapton, fiberglass, neoprene rubber, stainless-steel foil or aluminum foil as the back surface. Successful test results occur when the structural integrity of the module back surface is maintained. Test failures of these modules always occur for one of three reasons: the outermost back cover melts, rips, or is too porous. In each case flammable molten encapsulant, its gaseous byproducts, or both, penetrates the back surface of the module and bursts into flame. Future efforts to complete the technology base will concentrate on the spread-of-flame test, focusing on the more promising configurations identified in the initial series of tests.

Sugimura, R. S.↗
NASA NTRS1984

The integration of bypass diodes with terrestrial photovoltaic modules and arrays

Bypass diodes are often required to limit the potential for reverse voltage 'hot-spot' heating in high voltage arrays or in arrays that undergo periodic operation near the short-circuit point. In addition, when properly applied, bypass diodes can minimize the effect of shadowing and various internal module failures on the array energy output. This paper discusses the mechanical and electrical integration of bypass diodes beginning with the array-level considerations which influence the selection of an implementation approach. Concepts for the mounting of these diodes, both internally within the module encapsulant and externally to the exposed rear surface of the module, are described. Factors affecting the reliability of bypass diodes, including the control of junction temperature through adequate heat sinking and the derating of reverse voltage, are discussed.

Shepard, N. F., Jr.↗
NASA NTRS1984

Predicting electrochemical breakdown in terrestrial photovoltaic modules

Electrochemical corrosion of PV cells can cause a cell-to-frame short circuit with two undesirable resuits: (1) catastrophic loss of source-circuit power; and (2) high field maintenance (module replacement) costs. Parameter dependencies are determined and encapsulated two-cell coupons are exposed to a range of voltage differences, temperatures, and relative humidities. Material relative performance is assessed. Nine different metallization-encapsulation combinations are tested.

Mon, G. R.↗
NASA NTRS1986

Hermetic Edge Seals for Photovoltaic Modules

Corrosive atmospheric agents excluded to prolong cell life. Combination of two sealing techniques makes possible to protect solar cells from water vapor, oxygen, and other corrosive atmospheric constituents. Using three-step process, glass-to-metal hermetic seal formed around edge of solar-cell module. Elastomer seals used previously not as effective because they are permeable to water vapor and atmospheric gases.

Nowlan, M. J.↗
NASA NTRS1985

Reliability and engineering of thin-film photovoltaic modules

Objectives were to: examine thin-film cell attributes that influence module performance and reliability, explore the lessons and applicability of crystalline-silicon module technology to thin-film modules, review the current status of thin-film module technologies, and identify problem areas and needed research. A major need is to separate the effects and resons for reversible degradatin from nonreversible degradation. Amorphous-silicon (a-Si) reliability investigations are focusing on exploratory research investigations, accelerated Arrhenius-type testing of a-Si cells, real-time outdoor exposure testing of a-Si cells, cell failure analysis, and failure mechanism research. Studies included the reduction in strength of glass by high temperature depositions on glass and laser scribing, encapsulation materials development needs, and the testing of modules. The new materials and processes in thin-film modules will require a delinquent reliability effort, including: establishment of mechanism-specific reliability goals; quantification of mechanism parameter dependencies; prediction of expected long-term degradation; identification of cost-effective solutions; and testing and failure analysis of trial solutions.

Royal, E. L.↗
NASA NTRS1985

Photovoltaics module interface: General purpose primers

The interfacial chemistry established between ethylene vinyl acetate (EVA) and the aluminized back surface of commercial solar cells was observed experimentally. The technique employed is called Fourier Transform Infrared (FTIR) spectroscopy, with the infrared signal being reflected back from the aluminum surface through the EVA film. Reflection infrared (IR) spectra are given and attention is drawn to the specific IR peak at 1080/cm which forms on hydrolytic aging of the EVA/aluminum system. With this fundamental finding, and the workable experimental techniques, candidate silane coupling agents are employed at the interface, and their effects on eliminating or slowing hydrolytic aging of the EVA/aluminum interface are monitored.

Boerio, J.↗
NASA NTRS1984

Assessing photovoltaic module life from long-term environmental tests

An assessment is made of results obtained by an experimental program having as its aim the identification of critical temperature-humidity bias degradation mechanisms in solar cell modules intended to have an operating lifetime of the order of 20-30 years. These mechanisms are studied in the context of conditions encountered over the course of long term operation in various sites in the U.S. Accelerated tests for the assessment of product lifetime entail the development of a correlation between test and application conditions; this has been accomplished through an analytical procedure for the correlation of time-varying field exposures to constant-stress accelerated environments.

Otth, D. H.↗