Search NASA⌕ Search

SEARCH · Search NASA

Results for “piezoelectric response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Vibrational Energy Harvesting Using a Cantilever Model

Vibrational energy harvesting (VEH) is a method of capturing incidental mechanical vibrational energy and converting it to electrical energy. This is enabled by two technologies: Electromagnetic induction via a cantilever or piezoelectric devices. When designing a VEH system, a fast forward model is desired for response determination and optimal parameter estimation. An ordinary different equation (ODE) system model is developed for the cantilever system based upon the derivations of [1] and [2], and compared with a full electromechanical COMSOL model.

42 ENGINEERING↗
DOE OSTI2022

Magnetoelastic properties of multiferroic hexagonal ErMnO 3

Here, the strength and dynamics of magnetoelastic coupling through the paramagnetic (PM) – antiferromagnetic (AFM) – ferrimagnetic (FIM) transitions in multiferroic hexagonal ErMnO 3 have been investigated by Resonant Ultrasound Spectroscopy. Elastic stiffening by up to 2% below the PM – AFM transition at 80 K arises from biquadratic coupling between strain and the magnetic order parameter with relaxation times longer than ~10 -6 s for the response of spins to changes in strain. In contrast with YMnO 3 , the PM – AFM transition in ErMnO 3 is accompanied by a peak in acoustic loss immediately below the Néel point which is interpreted in terms of strain relaxation accompanying ordering of spins of Er 3+ at 4b sites. Changes in the magnetic ordering scheme at the AFM – FIM transition near 3 K are accompanied by elastic softening of ~0.03 %. During poling of the low temperature ferrimagnetic structure round magnetic hysteresis loops, small changes in elastic stiffness which arise due to the contribution of piezomagnetic and/or piezoelectric moduli are detected. Contributions of piezoelectric moduli to acoustic resonance frequencies also permit changes in the configuration of ferroelectric domains to be detected in response both to cycling through this transition and to application of a magnetic field. A peak in acoustic loss in the vicinity of 250 K is attributed to strain-mediated pinning/freezing of some aspect of the domain microstructure with an activation energy of ~0.25–0.3 eV. A return to the original elastic properties on heating to temperatures above ~250 K is interpreted in terms of backswitching of domains to the configuration they had at the start. These observations confirm the existence of subtle variations in magnetoelastic coupling behaviour relating to both the magnetic order parameters and magnetic domain structures.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Glancing Angle Deposition in Gas Sensing: Bridging Morphological Innovations and Sensor Performances

Glancing Angle Deposition (GLAD) has emerged as a versatile and powerful nanofabrication technique for developing next-generation gas sensors by enabling precise control over nanostructure geometry, porosity, and material composition. Through dynamic substrate tilting and rotation, GLAD facilitates the fabrication of highly porous, anisotropic nanostructures, such as aligned, tilted, zigzag, helical, and multilayered nanorods, with tunable surface area and diffusion pathways optimized for gas detection. This review provides a comprehensive synthesis of recent advances in GLAD-based gas sensor design, focusing on how structural engineering and material integration converge to enhance sensor performance. Key materials strategies include the construction of heterojunctions and core–shell architectures, controlled doping, and nanoparticle decoration using noble metals or metal oxides to amplify charge transfer, catalytic activity, and redox responsiveness. GLAD-fabricated nanostructures have been effectively deployed across multiple gas sensing modalities, including resistive, capacitive, piezoelectric, and optical platforms, where their high aspect ratios, tailored porosity, and defect-rich surfaces facilitate enhanced gas adsorption kinetics and efficient signal transduction. These devices exhibit high sensitivity and selectivity toward a range of analytes, including NO2, CO, H2S, and volatile organic compounds (VOCs), with detection limits often reaching the parts-per-billion level. Emerging innovations, such as photo-assisted sensing and integration with artificial intelligence for data analysis and pattern recognition, further extend the capabilities of GLAD-based systems for multifunctional, real-time, and adaptive sensing. Finally, current challenges and future research directions are discussed, emphasizing the promise of GLAD as a scalable platform for next-generation gas sensing technologies.

Chemistry↗
DOE OSTI2023

Irradiation Behavior of Piezoelectric Materials for Nuclear Reactor Sensors

In-situ measurement of surface acoustic wave (SAW) resonators were used to characterize piezoelectric materials behavior in a nuclear reactor environment. Lithium niobate and aluminum nitride devices were tested up to 500°C temperature and 450 kW reactor power (1.9x10 12 n/cm 2 s). The resonant frequency responds to step changes in temperature and power. Materials’ response are inferred from the observed resonant frequency changes, in particular the kinetic behavior is used to determine mechanisms responsible for observed changes. The observed response is attributed to two mechanisms: temperature increase from gamma heating and accumulation of radiation-induced defects. Both of these mechanisms alter the physical properties of the piezoelectric materials, particularly the elastic constants. The demonstrated repeatability and reliability of SAW devices are attractive for sensor applications in extreme environments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Specific resonance mode enhancement and suppression using non-uniform polarization of piezoelectric wafers: Theory and experiments

In this work, we present experimental demonstration of specific resonance mode enhancement and suppression in circular and rectangular piezoelectric wafers with engineered non-uniform polarization profiles. The polarization profiles are designed based on the electromechanical impedance response of non-uniformly polarized wafers as obtained from the theory. The circular wafers are fabricated with non-uniform polarization profiles that involve a central polarized region surrounded by an unpolarized region. The radius of the polarization zone is designed based on the condition for specific mode enhancement obtained from the electromechanical impedance response of non-uniformly polarized wafers. We actually show how the condition can not only be used to enhance but also to suppress electromechanical resonances. Two kinds of wafers are designed and fabricated to specifically suppress second and third radial modes respectively. Similarly, rectangular wafers are designed with two different kinds of non-uniform polarization profiles — the first of which enhances the second in-plane extensional mode in the impedance spectrum and the second polarization profile suppresses all the electromechanical resonances pertaining to the in-plane extensional modes and selectively excites only the in-plane bending modes. The proposed approach of using non-uniformly polarized wafers finds application in designing multi-frequency sensors/transducers, frequency-tuned receivers, acoustic beamforming, and other non-traditional applications such as information storage.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Nanoelectromechanical Control of Spin–Photon Interfaces in a Hybrid Quantum System on Chip

Color centers (CCs) in nanostructured diamond are promising for optically linked quantum technologies. Scaling to useful applications motivates architectures meeting the following criteria: C1 individual optical addressing of spin qubits; C2 frequency tuning of spin-dependent optical transitions; C3 coherent spin control; C4 active photon routing; C5 scalable manufacturability; and C6 low on-chip power dissipation for cryogenic operations. Here, we introduce an architecture that simultaneously achieves C1–C6. We realize piezoelectric strain control of diamond waveguide-coupled tin vacancy centers with ultralow power dissipation necessary. The DC response of our device allows emitter transition tuning by over 20 GHz, combined with low-power AC control. We show acoustic spin resonance of integrated tin vacancy spins and estimate single-phonon coupling rates over 1 kHz in the resolved sideband regime. Combined with high-speed optical routing, our work opens a path to scalable single-qubit control with optically mediated entangling gates.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Control of polarization in bulk ferroelectrics by mechanical dislocation imprint

Defects are essential to engineering the properties of functional materials ranging from semiconductors and superconductors to ferroics. Whereas point defects have been widely exploited, dislocations are commonly viewed as problematic for functional materials and not as a microstructural tool. In this work, we developed a method for mechanically imprinting dislocation networks that favorably skew the domain structure in bulk ferroelectrics and thereby tame the large switching polarization and make it available for functional harvesting. The resulting microstructure yields a strong mechanical restoring force to revert electric field–induced domain wall displacement on the macroscopic level and high pinning force on the local level. This induces a giant increase of the dielectric and electromechanical response at intermediate electric fields in barium titanate [electric field–dependent permittivity (ε 33 ) ≈ 5800 and large-signal piezoelectric coefficient ( d 33 *) ≈ 1890 picometers/volt]. Dislocation-based anisotropy delivers a different suite of tools with which to tailor functional materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Synchronous micromechanically resonant programmable photonic circuits

Abstract Programmable photonic integrated circuits (PICs) are emerging as powerful tools for control of light, with applications in quantum information processing, optical range finding, and artificial intelligence. Low-power implementations of these PICs involve micromechanical structures driven capacitively or piezoelectrically but are often limited in modulation bandwidth by mechanical resonances and high operating voltages. Here we introduce a synchronous, micromechanically resonant design architecture for programmable PICs and a proof-of-principle 1×8 photonic switch using piezoelectric optical phase shifters. Our design purposefully exploits high-frequency mechanical resonances and optically broadband components for larger modulation responses on the order of the mechanical quality factor Q m while maintaining fast switching speeds. We experimentally show switching cycles of all 8 channels spaced by approximately 11 ns and operating at 4.6 dB average modulation enhancement. Future advances in micromechanical devices with high Q m , which can exceed 10000, should enable an improved series of low-voltage and high-speed programmable PICs.

42 ENGINEERING↗
DOE OSTI2021

Enhanced ferroelectric and piezoelectric properties of BCT-BZT at the morphotropic phase boundary driven by the coexistence of phases with different symmetries

The discovery of lead-free piezoelectric materials is crucial for future information and energy storage applications. Enhanced piezoelectric and other physical properties are commonly observed near the morphotropic phase boundary (MPB) composition of ferroelectric solid solutions. The (1 – x)Ba(Zr 0.2 Ti 0.8 )O 3 -x(Ba0.7Ca0.3)TiO 3 (BZT-xBCT) system exhibits a large electromechanical response around its MPB region at x = 0.5. Here, we report experimental and theoretical results of BZT-xBCT over a wide composition range (0.3 ≤ x ≤ 1.0). X-ray diffraction and Raman spectroscopy studies indicate a composition-induced structural phase transition from a rhombohedral (R3m) phase at x ≤ 0.4 to a tetragonal (P4mm) phase at x ≥ 0.6 through a multiphase coexistence region at 0.45 ≤ x ≤ 0.55 involving orthorhombic + tetragonal (Amm2 + P4mm) phases. First-principles calculations elucidate the phase competition in the coexistence region. The critical composition (x = 0.5) displays enhanced dielectric, ferroelectric, and piezoelectric properties, where notably d 33 ~ 320 pC/N. This paper provides clear evidence of Amm2+P4mm crystallographic phases in the MPB region, which is responsible for the improved functional properties.

MPB↗
DOE OSTI2020

Low-cost, constrained-motion dynamometer for milling force measurement

This paper describes the design and testing of a low-cost dynamometer for milling force measurement. The monolithic design is based on constrained-motion/flexure-based kinematics, where force is inferred from displacement measured using a low-cost optical interrupter (i.e., a knife edge that partially interrupts the beam in an emitter-detector pair). The time-dependent displacement of the dynamometer’s moving platform caused by the milling force is converted to the frequency domain, multiplied by the inverse of the single degree of freedom frequency response, and converted back to the time domain to obtain the time dependent cutting force. Lastly, comparisons with commercially available, piezoelectric-based force measurement are provided.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

AFM Microcantilever With a Collocated AlN Sensor-Actuator Pair: Enabling Efficient Q-Control for Dynamic Imaging

This manuscript presents a novel microcantilever with an embedded piezoelectric sensor-actuator pair for dynamic atomic force microscopy (AFM). The transducer pair is constructed from a two-layered AlN stack. Stacking the piezoelectric transducers in this manner leads to a minimal feedthrough from actuation to sense electrode, granting a high dynamic range frequency response for dynamic mode AFM. The cantilever's design allows for dual mode operation at 1 st and 2 nd resonance modes. High resolution tapping mode imaging results are reported, while the cantilever is operated at these modes. A feedback control loop is used to modify quality factor of the 1 st mode of the cantilever, using a positive position feedback (PPF) controller. Here, a faster response time is achieved by reducing the Q-factor, enabling the cantilever to track the topography at a higher scan rate. Results of bimodal AFM imaging are reported, using amplitude changes of the 1 st mode for surface topography, while material properties are encoded in phase changes of the 2 nd mode.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Determining the oxidation stability of SnSe under atmospheric exposure

Abstract Understanding surface stability becomes critical as 2D materials like SnSe are developed for piezoelectric and optical applications. SnSe thin films deposited by molecular beam epitaxy showed no structural changes after a two-year exposure to atmosphere, as confirmed by X-ray diffraction and Raman spectroscopy. X-ray photoelectron spectroscopy and reflectivity show a stable 3.5 nm surface oxide layer, indicating a self-arresting oxidative process. Resistivity measurements show an electrical response dominated by SnSe post-exposure. This work shows that SnSe films can be used in ambient conditions with minimal risk of long-term degradation, which is critical for the development of piezoelectric or photovoltaic devices. Graphical Abstract

Chin, Jonathan R. (ORCID:0000000273205678)↗
DOE OSTI2021

Characterization of Advanced Manufactured Surface Acoustic Wave Sensor for Temperature Measurement in Nuclear Applications

As part of a collaborative effort between Idaho National Laboratory and the Boise State University, printed SAW transducers were developed. The transducers were first modelled and evaluated for optimum performance, then fabricated using several piezoelectric substrates. These printed SAW-sensors were tested for temperature sensing ability and found to be highly sensitive and with a very linear response over the tested range.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Effectiveness and nonlinear characterization of vibro-impact energy harvesting absorbers in controlling base-excited systems

In this study, model derivations are carried out of a dynamical system under base excitations with a piezoelectric energy harvesting absorber as the tuned-mass-damper. Additionally, amplitude stoppers are included to the absorber in order to create a broadband resonant response, increasing the window of operational use for energy harvesting and system's control. This study is unique in the fact that the energy harvester is coupled to the source of its excitation. A nonlinear reduced-order model is developed using Euler–Lagrange principle and the Galerkin method to accurately estimate the energy harvesting absorber's displacement, harvested power, and the oscillating response of the primary structure. The nonlinear interaction of the energy harvesting absorber and the amplitude stoppers are the focus of this study, where an in-depth investigation of bifurcation points of the primary structure and energy harvesting absorber responses is performed. Due to a transfer of energy between the primary structure and the absorber, it is shown that a soft stopper with stiffness $5 \times {10^3}\,{\text{N}}\;{{\text{m}}^{ - 1}}\,$ has great control of the primary structure with 60% of the uncontrolled amplitude being reduced, as well as an increase of the harvested energy. Medium stoppers with small initial gaps size and hard stoppers do not control the primary structure and show a decrease in the energy harvesting capabilities due to the activation of the nonlinear contact-impact interactions. Finally, these stoppers also generate aperiodic regions due to the possible presence of grazing bifurcations.

36 MATERIALS SCIENCE↗
DOE OSTI2020

NDE Technology Engineering Program for Hanford DST Non-Visual Volumetric Inspection Technology: Phase II RAVIS Radiation Tolerance Test Report

This test report provides the results of radiation tolerance robustness testing that was performed on samples of robotic components and an ultrasonic guided wave air-slot sensor that represent components/sub-systems of the Robotic Air-slot Volumetric Inspection System (RAVIS) that has been engineered for volumetric inspection of Hanford tank bottom plates via under-tank refractory pad air-slots. The specific components tested for 1) functionality during active irradiation and 2) tolerance to cumulative radiation dose (until failure or upon reaching a cumulative dose test limit) were: • four samples each of a printed circuit board (PCB) and direct current (DC) motor, which are robotic components, and • 26 ultrasonic piezoelectric elements (samples) inside an air-slot sensor. The robotic components are part of the RAVIS air-slot inspection crawler drive control system that is responsible for remote communication with and actuation of the air-slot inspection crawler. The failure of either of these components during under-tank deployment would require manual retrieval via the crawler’s tether, which risks damage to the robot/refractory/tank. Preemptive replacement of the components at appropriately conservative dose/time intervals informed by failure dose would reduce the likelihood of under-tank failure. The components were included in radiation tolerance testing to quantify their failure doses to inform replacement intervals. The air-slot sensor is responsible for collecting ultrasonic inspection data (scan images) for the tank bottom plates during under-tank deployment. Compromised signal quality due to elevated noise levels caused by gamma radiation would compromise inspection performance. The air-slot sensor was included in radiation tolerance testing to quantify the impact of active irradiation on sensor signal quality. The irradiation and in-situ functional tests of the PCBs, DC motors and air-slot sensor took place in June and July 2020 at the Pacific Northwest National Laboratory. Testing was performed at a gamma dose rate near 300 rad/hr., which, in the absence of under-tank dose rate data, has been conservatively estimated to be the upper-bound dose rate beneath the primary tanks at Hanford. Irradiation took place at elevated temperatures of 150-200°F to determine failure doses that reflect the compounding effects of gamma radiation and heat. The test results revealed: • The DC motors can tolerate being actively irradiated at the high dose rate at 200°F and can tolerate a cumulative dose of 300,000 rad, that which would be incurred after 5 years of service at the 300 rad/hr dose rate. The component therefore meets minimum and preferred radiation tolerance and lifecycle requirements for robotic components. • The air-slot sensor can tolerate being actively irradiated at the high dose rate at 150°F and can tolerate a cumulative dose of 60,000 rad, that which would be incurred after 1 year of service at the 300 rad/hr dose rate. The sensor therefore meets minimum radiation tolerance and lifecycle requirements. • The PCB can tolerate being actively irradiated at the high dose rate, but can only tolerate a cumulative dose of 19,000 rad at 150-200°F. The PCB does not meet minimum radiation tolerance and lifecycle requirements; however, because the component is considered replaceable, it can be replaced before a cumulative dose of 19,000 rad is reached, determined through either monitoring with a dosimeter or scheduled time intervals that are calculated based on conservative estimates of under-tank dose rates.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Laser Doppler vibrometry for piezoelectric coefficient ($d_{33}$) measurements in irradiated aluminum nitride

Sensors used for experiments in advanced reactors must survive in harsh environments. Few material systems can be used to construct sensors viable for extreme conditions. Aluminum nitride (AlN) is one such material because it has high thermal stability and radiation resistance and sustains good piezoelectric and dielectric properties at high temperatures. In this work, the piezoelectric coefficient $d_{33}$ of the AlN single-crystal with thermal and irradiation damage was investigated using an indirect method with a laser Doppler vibrometer (LDV). Surface electrodes were deposited on the AlN samples, and the vibration response of the samples to an applied voltage was monitored using the LDV as a function of the excitation frequency. The $d_{33}$ estimation was based on the excitation voltage and the thickness-mode displacement extracted from the LDV measurements. Further, six AlN substrates were irradiated with 8 MeV Al 2+ at three fluences (10 15 , 10 16 , and 10 17 ions/cm 2 ) and two temperatures (300 °C and 500 °C). The $d_{33}$ for the six irradiated samples and one pristine sample were measured, and the measurement uncertainty was estimated based on five repeated tests. All samples were also measured by a commercial piezometer for comparison. The experimental results demonstrate that the piezoelectric coefficients obtained by LDV were about 0.8–1.16 pm/V lower than those obtained by the piezometer. With the compensation of the clamping effect, the corrected LDV values are similar to the piezometer results. Both show similar trends in all samples, which validates the feasibility of the proposed method for $d_{33}$ measurement. Based on the LDV results, the irradiated samples show a 12%–22% decrease in $d_{33}$ compared with the pristine samples. The samples irradiated under the same fluence at a higher temperature (500 °C) demonstrated a lower $d_{33}$ than those at 300 °C. The effect of the retro-reflective tape, sample temperature, and sample size on the $d_{33}$ measurement were also studied.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Al 0.68 Sc 0.32 N Lamb wave resonators with electromechanical coupling coefficients near 10.28%

Aluminum scandium nitride (Al 1-x Sc x N/AlScN) (x = 0.32) Lamb wave resonators (LWR) have been fabricated and tested to demonstrate electromechanical coupling coefficients (k t 2 ) in excess of 10%. The resonators exhibited an average k t 2 and unloaded quality factor (Q u ) of 10.28% and 711, respectively, when calculated from the measured data. Applying the Butterworth Van-Dyke (BVD) model to the measured data enabled the extraction of the resonator's lumped element parameters to calculate the motional quality factor (Q m ), which neglects the contributions of the electrical traces. For the best measured resonator response, results from the BVD model showed a Q m of 1184 and a resulting figure-of-merit (FOM = K 2 ·Q m ) of 100. Comparing the response of similar AlScN and AlN resonators shows that the AlScN LWR has a significantly lower motional resistance (R m ), suggesting that AlScN has a strong potential for use in piezoelectric microelectromechanical oscillators.

42 ENGINEERING↗