Search NASA⌕ Search

SEARCH · Search NASA

Results for “pinch”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Staged Z-pinch modeling of high and low atomic number liners compressing deuterium targets using parameters of the Z pulsed power facility

The staged Z-pinch is a potentially transformative magneto-inertial fusion energy concept where a high atomic number liner implodes on a deuterium or deuterium-tritium target using multi-MA pulsed current. Over the past several years, this concept was studied experimentally on 1 MA facilities with argon or krypton gas puffs compressing a magnetized deuterium target. Consistent thermonuclear neutron yield of 1010 per shot was measured with krypton liners. In this paper, we investigate the fusion performance of deuterium targets of varying density undergoing compression with low (beryllium) and high atomic number liners (silver, tantalum) using parameters of the Z pulsed power facility. Silver and tantalum liners create strong shocks that preheat the target plasma above 100 eV and pile up liner material at the liner-target interface. The increased mass density at the interface creates strong ram pressure just before the pinch stagnation time. The target plasma is heated to 2–4 keV, in contrast to the < 0.5 kV temperature calculated for the beryllium case. The high atomic number liners produce neutron yield orders of magnitude higher than the yield from the low atomic number liner.

Ruskov, E. (ORCID:0000000336724580)↗
DOE OSTI2022

Studying of multi-shell gas-puff Z-pinches using x-ray spectroscopy with spatial resolution

Dynamics and parameters of gas-puff Z-pinch plasmas at stagnation were studied using x-ray spectroscopic diagnostics. In experiments on a 1 MA pulsed power generator, multilayer coaxial loads were made using a triple-nozzle gas-puff valve. High-luminosity spectrographs with spherically bent crystals made it possible to record spectra with high spatial resolution along the pinch axis and to record two-dimensional plasma images in separate spectral lines. Using various combinations of gases in the nozzles and adding small amounts of a gas tracer, the final structure and composition of the compressed plasma were determined. Furthermore, plasma parameters were estimated by modeling the spectra using the PrismSPECT program, but with the limitation that the spectra were time-integrated, so that spectra from different gases and at different positions may have been emitted at different times.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Impact of power flow on Z-pinch loads

Magnetically insulated transmission lines (MITLs) are used to deliver tens of MA to a Z-pinch load. The MITLs suffer current losses due to contaminant plasma located in the anode–cathode gap which is swept toward the load along the power flow. The swept up contaminant plasma can deposit mass and energy onto the load resulting in deformations or the seeding of macroscopic instabilities. This paper discusses 2D fully kinetic simulations of the contaminant plasma evolution which predict the current losses and the flux of mass and energy onto the load. Furthermore, the effects of a dynamic, i.e., imploding, load are shown to increase both the current loss and the mass and energy flux. The MITL used is a conical, radially converging design which is a feature common to MA-scale Z-pinch accelerators.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Neutron-producing gas puff Z-pinch experiments on a fast, low-impedance, 0.5 MA linear transformer driver

A study on the neutron production from single and double gas puff Z-pinches on the CESZAR linear transformer driver with ~0.45 MA current and 170 ns rise time is presented. Total neutron yield measurements made with a LaBr activation detector are compared for three configurations, using a double nozzle setup. When a single, hollow, deuterium gas shell was used, reliable implosions could only be attained at higher load mass than the optimal value to match implosion time with the driver rise time, with neutron yields of ~10 6 per pulse. The use of a double gas puff configuration with a deuterium center jet allowed a reduction in the shell density and operation closer to machine-matched conditions, recording up to (4.1 ± 0.3) × 10 7 neutrons/pulse when either Kr or D 2 was used in the shell. For a comparable mass and implosion time, using a higher atomic-number gas in the outer shell results in more unstable plasma surface and smaller plasma radius at the location of instability bubbles, which, however, do not seem to consistently correlate with a higher neutron yield. Comparing implosion dynamics with models and neutron yields with literature scaling suggests that the machine current is not well coupled to the plasma during the final stages of compression. Optimizing current and energy coupling to the pinched plasma is critical to improving performance, particularly in low-impedance drivers.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Asymptotic scaling laws for the stagnation conditions of Z-pinch implosions

Implosions of magnetically driven annular shells (Z pinches) are studied in the laboratory to produce high-energy-density plasmas. Such plasmas have a wide-range of applications including x-ray generation, controlled thermonuclear fusion, and astrophysics studies. In this work, we theoretically investigate the in-flight dynamics of a magnetically driven, imploding cylindrical shell that stagnates onto itself upon collision on axis. The converging flow of the Z-pinch is analyzed by considering the implosion trajectory in the (A, M) parametric plane, where A is the in-flight aspect ratio and M is the implosion Mach number. For an ideal implosion in the absence of instabilities and in the limit of A ≫ 1, we derive asymptotic scaling laws for hydrodynamic quantities evaluated at stagnation (e.g., density, temperature, and pressure) and for performance metrics (e.g., soft x-ray emission, K-shell x-ray emission, and neutron yield) as functions of target-design parameters.

Ruiz, D. E. [Sandia National Laboratories (SNL-NM)↗
DOE OSTI2025

General kinetic ion-induced electron emission model for metallic walls applied to biased Z-pinch electrodes

A kinetic ion-induced electron emission (IIEE) model for general applications is developed to obtain the emitted electron energy spectrum for a distribution of ion impacts on a metallic surface. We assume an ionization cascade mechanism and use empirical models for the ion and electron stopping powers. The emission spectrum and the secondary electron yield (SEY) are validated for a variety of materials. The IIEE model is used to study the effect of IIEE on the plasma-material interactions of Z-pinch electrodes. Un-magnetized Boltzmann-Poisson simulations are performed for a Z-pinch plasma doubly bounded by two biased copper electrodes with and without IIEE at bias potentials from 0 to 9 kV. At the anode, the SEY decreases from 0 to 1 kV, but then increases at higher bias potentials. At the cathode, the SEY is much larger due to higher energy ion bombardment and grows with bias potential. As the bias potential increases, the emitted cathode electrons are accelerated to higher energies into the domain, collisionally heating the plasma. Above 1 kV, the heating is strong enough to increase the plasma potential. Despite SEY greater than 1, only a classical sheath forms as opposed to a space-charge limited or inverse sheath due to the emitted electron flux not reaching the space charge current saturation limits. Furthermore, the current in the emissionless cases saturates to a value lower than experiment. With IIEE, the current does not saturate and continues to increase with the 4 kV case, matching most closely with the experiment.

Carbon based materials↗
DOE OSTI2024

Whole device modeling of the fuze sheared-flow-stabilized Z pinch

Abstract The FuZE sheared-flow-stabilized Z pinch at Zap Energy is simulated using whole-device modeling employing an axisymmetric resistive magnetohydrodynamic formulation implemented within the discontinuous Galerkin WARPXM framework. Simulations show formation of Z pinches with densities of approximately 10 22 m −3 and total DD fusion neutron rate of 10 7 per µ s for approximately 2 µ s. Simulation-derived synthetic diagnostics show peak currents and voltages within 10% and total yield within approximately 30% of experiment for similar plasma mass. The simulations provide insight into the plasma dynamics in the experiment and enable a predictive capability for exploring design changes on devices built at Zap Energy.

Physics↗
DOE OSTI2021

Studies and optimization of hybrid X-pinches

Studies were carried out on the hybrid X-pinch (HXP) configuration for several wire materials using a 40ns risetime, 300-kA pulsed-power generator with the goal of optimizing the HXP X-ray burst parameters for different applications. The gap distance between the conical electrodes of the hybrid X-pinch was varied from 0.5 to 5 mm for Al, Ag, Ti, and Mo using different wire diameters to maintain a consistent mass per unit length from one material to the next. It was found that 0.5 - 1 mm gap spacing was optimal to obtain a single X-ray burst, while the number of X-ray bursts increased with gap spacing for all materials at a rate of 1-2/mm. Time consistency studies of the first X-ray burst were carried out for Ti wire by changing the gap distance and wire diameter while observing the time of occurrence of the X-ray bursts. Here, it was found that a 40μm Ti wire load with a 3mm electrode gap spacing had the highest probability to have the first X-ray burst reproducibly within a 2 ns time window. Time-resolved and time-integrated diagnostics provided information about the source size, time of occurrence, intensity, and the number of the X-ray bursts.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Time-resolved investigation of subnanosecond radiation from Al wire hybrid X pinches

K-shell x-ray spectra from Al wire hybrid X pinches have been studied using an x-ray streak camera with better than 0.1-ns time resolution together with a Focusing Spectrograph with Spatial Resolution (FSSR) spectrograph. High-intensity radiation with a continuumlike spectrum was observed in the subnanosecond initial phase of the x-ray pulse generated by the hybrid X pinch (HXP). Here, the absence of spectral lines in this phase and the extremely small x-ray source size indicates the importance of radiative processes in the final phase implosion dynamics. Plasma parameters in the following phases of the HXP were determined from analysis of the line intensities. Point-projection radiography together with a slit-step wedge camera and an FSSR spectrograph without time resolution were used to show the number of radiation sources, and to give information on the time-integrated photon energy spectrum.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Stabilization of Liner Implosions via a Dynamic Screw Pinch

Magnetically driven implosions are susceptible to magnetohydrodynamic instabilities, including the magneto-Rayleigh-Taylor instability (MRTI). To reduce MRTI growth in solid-metal liner implo-sions, the use of a dynamic screw pinch (DSP) has been proposed [P. F. Schmit et al., Phys. Rev. Lett. 117, 205001 (2016)]. In a DSP con guration, a helical return-current structure surrounds the liner, resulting in a helical magnetic eld that drives the implosion. Here, we present the rst experimental tests of a solid-metal liner implosion driven by a DSP. Using the 1-MA, 100{200-ns COBRA pulsed-power driver, we tested three DSP cases (with peak axial magnetic elds of 2 T, 14 T, and 20 T) and a standard z-pinch (SZP) case (with a straight return-current structure and thus zero axial eld). The liners had an initial radius of 3.2 mm and were made from 650-nm-thick aluminum foil. Images collected during the experiments reveal that helical MRTI modes developed in the DSP cases, while non-helical (azimuthally symmetric) MRTI modes developed in the SZP case. Additionally, the MRTI amplitudes for the 14-T and 20-T DSP cases were smaller than in the SZP case. Speci cally, when the liner had imploded to half of its initial radius, the MRTI amplitudes for the SZP case and for the 14-T and 20-T DSP cases were, respectively, 1.1-0.3 mm, 0.7-0.2 mm, and 0.3-0.1 mm. Relative to the SZP, the stabilization obtained using the DSP agrees reasonably well with theoretical estimates.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

PINCH POINT ANALYSIS OF GAS COOLERS IN TRANSCRITICAL R1336mzz(Z) HIGH-TEMPERATURE HEAT PUMPS

The majority of high-temperature heat pumps (HTHPs) operate subcritical vapor compression cycles, where the maximum sink temperature is limited by the critical temperature of refrigerants. In HTHPs with a sink temperature of ≥ 150°C, transcritical cycles overcome this limitation by rejecting heat in the supercritical regions of refrigerant. Supercritical refrigerants in gas coolers have a large temperature glide and substantial nonlinear variation in specific heat capacity vs. temperature. Closely matching the refrigerant glide temperature and the heat sink temperature profile greatly impacts the heat transfer characteristic of gas coolers and the overall performance of HTHPs. This study conducts a pinch point analysis for the gas cooling process of supercritical R1336mzz(Z) in HTHPs. A finite volume element model of a supercritical R1336mzz(Z) counterflow gas cooler is built and solved. This study evaluates the influences of operating conditions, including inlet and outlet of coolants, refrigerant evaporation temperature and superheat degree, pinch temperature difference, and heat rejection pressure, on the performance of HTHPs. The optimal discharge pressures in gas coolers are proposed for industrial spray dryers in providing drying air at 170°C−210°C. The results of the present study help design gas coolers in transcritical R1336mzz(Z) HTHPs.

Wang, Pengtao↗
DOE OSTI2020

Characterization of Self-Magnetic Pinch (SMP) Radiographic Diode Performance on RITS-6 at Sandia National Laboratories

The goals of an electron beam-driven radiographic source are the focusing of high current at high voltage to a minimal spot size with excellent shot-to-shot reproducibility. The Self-Magnetic Pinch (SMP) diode makes use of such an intense electron beam impinging on a high-atomic weight (tantalum) converter, a counter-streaming ion beam to help minimize the spot size, and operation in a magnetic field-free diode region which further encourages small spot size. Through a series of diode development experiments, output voltages up to 12.5 MV and output currents up to 225 kA have been characterized, with resulting spot sizes below ~ few mm. Scaling studies with parameter variation, such as diode aspect ratio and anode-cathode (A-K) gap variation, give systematic validation to what has heretofore been noted anecdotally by other research groups. While the lack of an imbedded magnetic field helps minimize the SMP spot size, a secondary result may be the generation of beam instabilities which can terminate the radiation pulse. There is anecdotal evidence that in-situ DC heating of the diode region can help stabilize the beam pinch. Clear experimental evidence exists that DC heating/RF cleaning results in better control over the counter-streaming ion population. Expanded use of spatial dose-rate detection is shown to yield new insights into electron beam dynamics in the SMP diode. An attendant study of the SMP diode as a load for an Inductive Voltage Adder (IVA) driver leads to insights into the behavior of the IVA-SMP diode configuration, viewed as a total system, and yields constraints on the overall impedance behavior of the SMP diode load.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

The study of local overheating and plasma formation on stainless steel z-pinch targets

Plasma formation from intensely ohmically heated conductors is known to be highly non-uniform, as local overheating can be driven by micron-scale imperfections. Detailed understanding of plasma formation is required to predict the performance of magnetically driven physics targets and magnetically-insulated transmission lines (MITLs). Previous LDRD-supported work (projects 178661 and 200269) developed the electrothermal instability (ETI) platform, on the Mykonos facility, to gather high-resolution images of the self-emission from the non-uniform ohmic heating of z-pinch rods. Experiments studying highly inhomogeneous alloyed aluminum captured complex heating topography. To enable detailed comparison with magnetohydrodynamic (MHD) simulation, 99.999% pure aluminum rods in a z-pinch configuration were diamond-turned to ~10nm surface roughness and then further machined to include well-characterized micron-scale "engineered" defects (ED) on the rod's surface (T.J. Awe, et al., Phys. Plasmas 28, 072104 (2021)). In this project, the engineered defect hardware and diagnostic platform were used to study ETI evolution and non-uniform plasma formation from stainless steel targets. The experimental objective was to clearly determine what, if any, role manufacturing, preparation, or alloy differences have in encouraging nonuniform heating and plasma formation from high-current density stainless steel. Data may identify improvements that may be implemented in the fabrication/preparation of electrodes used on the Z machine. Preliminary data shows that difference in manufacturer has no observed effect on ETI evolution, stainless alloy 304L heated more uniformly than alloy 310 at similar current densities, and that stainless steel undergoes the same evolutionary ETI stages as ultra-pure aluminum, with increased emission tied to areas of elevated surface roughness.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Hard x-ray imaging and characterization of staged z-pinch plasmas in order to exclude ion beams as cause of fusion

Prior to the start of the INFUSE project, a 1-D x-ray device had been developed to detect > 5 keV x-rays and, by using the device as a pinhole camera, determine the location of the source of these x-rays. The system was also used in a non-camera mode to measure the energy of the X-rays by having different thicknesses of attenuating material on different pixels. This dual-purpose had been used in three plasma experiments: the laboratory magnetized plasma jet at Caltech, the laboratory solar nanoflare at Caltech, and at the 500 kA staged Z-pinch (CESZAR) at UCSD. Preliminary measurements at the UCSD facility indicated that hard x-rays with energies ranging from ~27 to over 100 keV were created and that these x-rays likely originated at the Z-pinch’s anode. These preliminary data also indicated that the x-rays’ origin was coincident with the moment of peak compression. The major goal of the INFUSE proposal was to confirm these preliminary results. This confirmation was to be made by improving the imaging capability to two dimensions, increasing the time resolution of the camera, and using the x-ray diagnostic alongside time-resolved neutron detectors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Evolution of the electrothermal instability from thick rod z pinches subject to dynamically and statically applied axial magnetic field

LDRD Project 229427 aimed to determine how electrothermal instability (ETI) driven heating on a z-pinch rod pulsed with intense current evolves under mixed magnetic field (azimuthal + axial) conditions, which is pertinent to pulsed-power-driven magnetically-insulated transmission lines and physics targets. Experiments focused on diagnosing ETI-driven heating from deliberately-machined and well-characterized micron-scale surface defects (referred to as engineered defects or ED). Prior to the start of this project, understanding of how unmagnetized (B z =0) ED evolve had been obtained—simulations largely reproduce the experimentally observed high temperature spots which develop at the poles of bare/uncoated ED. Project 229427 extended the Mykonos Facility ED experimental platform to include axial field. In the first class of experiments, axial field was provided “dynamically” via a helical return can (HRC). In this case, B z and B θ rise at the same rate. Generally, the HRC generated magnetic field at a fixed polarization angle Φ B =arctan(B z /B θ )=15° on the rod's surface. In the second class of experiments, axial field was provided “statically” via a slow-rising (millisecond) external Helmholtz coil pair. In this case, B z was effectively constant/static throughout the 100 ns rise of the Mykonos current. For either case, a primary goal was to determine whether ETI provides a helical seed perturbation for the subsequent growth of the helical magneto Rayleigh-Taylor modes observed in MagLIF (static B z ) and dynamic screw pinch (DSP, dynamic B z ) experiments. When dynamic field was applied using an HRC, emissions from individual ED aligned toward Φ B , while emissions from ED within pairs elongated and preferentially merged along Φ B . These data strongly support that for a randomized defect distribution, heating from nearby current-density perturbations will favorably merge about Φ B to generate an extended seed perturbation that aligns toward the surface-field polarization, and this may impact the orientation of subsequent MRT growth on imploding liners. The results from the static field experiments were largely inconclusive, as any ETI heating rotation, if present, was obscured/overwhelmed by local/random heating from ED rim imperfections.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1972

Transient flow and heating characteristics in a pinched plasma column.

The generation of axial flow and heating of an argon plasma in a pinched plasma column of a pulsed, linear z-pinch device was examined experimentally and analytically. Transient (about 5 microsec) axial pressure profiles identify three characteristic periods in the column history. These include (1) strong axial pressure asymmetry indicative of plasma streaming, (2) isotropic, rapidly rising plasma pressure indicative of plasma heating, and (3) column breakup. An efficient conversion of radial collapse to axial streaming velocity is identified. Mechanisms for such an effect and subsequent heating are evaluated; significance to transients in pulsed plasma accelerators is identified.

York, T. M.↗
NASA NTRS1974

Transient flow and heating in a pinched plasma column

The axial flow and heating of an argon plasma in a pinched plasma column of a pulsed, linear z-pinch device was experimentally examined with a unique pressure sensing instrument capable of resolving mass flow properties. Transient axial pressure profiles identify periods of intense flow and heating. Mechanisms generating such effects are considered.

York, T. M.↗
NASA NTRS1976

Absorption of CO2-laser radiation in a hypocycloidal-pinch plasma

Absorption of a 50-J pulsed CO2 laser beam in the plasma produced in a hypocycloidal-pinch apparatus was studied. The apparatus consists of three disk electrodes with a 5-cm hole on the axis. The current sheets are snow-plowed toward the center of the hole to produce a plasma with a density greater than 10 to the 18th/cu cm and a temperature near 1 keV which emits soft X rays for 5 microsec. IR detectors measured the laser radiation incident onto, transmitted through, and scattered from the plasma as functions of time. For a period up to 70 microsec from the onset of X-ray emission, neither transmitted nor scattered laser radiation was observed above the detector threshold of 0.3% of the incident flux. This indicates effective absorption of the laser beam (greater than 99%) and that the particle confinement time extends far beyond the energy confinement time of 5 microsec. Thus, the plasma in this apparatus appears much more amenable to laser heating than that in a theta pinch.

Lee, J. H.↗