Search NASA⌕ Search

SEARCH · Search NASA

Results for “plasma science and technology”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Simultaneous analysis of collinear neutron time-of-flight (nToF) traces applied to pulsed fusion experiment

On pulsed fusion experiments, the neutron time of flight (nToF) diagnostic provides critical information on the fusion neutron energy spectrum. This work presents an analysis technique that uses two collinear nToF detectors, potentially to measure nuclear bang time and directional flow velocities. Two collinear detectors may be sufficient to disambiguate the contributions of nuclear bang time and directional flow velocities to the first moment of the neutron energy spectrum, providing an independent measurement of nuclear bang time. In conclusion, preliminary results from measured nToF traces on the National Ignition Facility and additional applications of this technique are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Thermal stability of oxidized ultrathin Li films on TZM for plasma facing components

For improved understanding of the behavior of Li plasma facing components (PFCs) in the presence of oxygen impurities, we report on the thermal stability of ultrathin (up to 1.0 nm) LiO x films on a titanium-zirconium-molybdenum (TZM) alloy substrate over the temperature range of 310–1400 K. LiO x films were prepared by either post-oxidation of Li films or Li films deposited on an oxygen-precovered TZM surface. Thermal stability of these films was studied using a combination of temperature programmed desorption (TPD), X-ray photoelectron spectroscopy (XPS), and low-energy ion scattering (LEIS). For post-oxidized Li films, TPD showed that no Li desorption occurred until temperatures above 620 K, and then Li desorbed from the surface via at least three desorption peaks. The O 1s XPS spectra on the post-oxidized films at 310 K indicate the formation of lithium oxide (Li2O) and peroxide/hydroxide (Li 2 O 2 /LiOH). The peroxide/hydroxide converts to oxide after heating to 680 K with no desorption of Li or O 2 , and then this film decomposes to liberate Li into the gas phase while leaving oxygen at the TZM surface. Heating the LiO x films to 1070 K led to a solid-state reaction with surface Mo atoms of the substrate to form a condensed binary lithium molybdenum oxide (LixMoOy) phase, which upon further heating decomposed to liberate gas phase binary lithium molybdenum oxide species. Li deposition on an oxygen-precovered TZM surface formed a complex, highly stable, oxygen rich, Li-O-Mo interfacial oxide. Li desorption from multilayer Li films on oxygen-precovered TZM surfaces occurred in a metallic Li multilayer peak and three other oxide-derived peaks. These results support the improved thermal stability of oxidized lithium as compared to metallic Li and have implications for Mo impurity transport into the plasma at high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Magnetic geometry effects on turbulent density fluctuations in Wendelstein 7-X

Line-integrated density fluctuation measurements from the core of the optimised stellarator Wendelstein 7-X (W7-X) are studied in the context of magnetic field geometry changes. The amplitude as well as the spectral distribution of fluctuations is affected by varying the magnetic field configuration. Weaker turbulent fluctuations are observed in configurations with higher rotational transform and lower magnetic mirror depth. Simulations with the gyrokinetic codes stella and GENE-3D are used to investigate the role of magnetic geometry for the experimental observations. The stabilising effect of the high rational transform configuration is reproduced by simulations and can be associated with stronger shaping of the magnetic field. This leads to increased finite Larmor radius and local shear effects, which limit the toroidal extent of ion temperature gradient (ITG) modes. For W7-X configurations with higher magnetic mirror depth, gyrokinetic theory and simulations predict weaker fluctuations, since they are closer to having the maximum-J property, which has a stabilising effect on trapped-electron mode and ITG. The opposite trend is observed experimentally, which can therefore not be explained by geometry effects on turbulence alone.

Wendelstein-7X↗
DOE OSTI2025

Effects of midplane density gradient in the propagation of high-harmonic fast waves considering high temperature anisotropy in the scrape-off layer of NSTX-U

High-Harmonic Fast Wave (HHFW) heating experiments in NSTX have shown that up to 60% of the injected power can be lost in the Scrape-Off Layer (SOL) when the density is above the fast wave cutoff density in front of the antenna, for which the fast wave is able to propagate into the plasma. This work models HHFW propagation in the SOL plasmas of NSTX-U using a 2D divertor SOL profile derived from the pressure assumption and the finite element temperature solution, which accounts for the high anisotropy of heat conduction in a 2D axisymmetric geometry. In this work, the two-dimensional axisymmetric SOL temperature profile is first evaluated by solving the steady-state non-linear heat conduction equation, in which thermal conductivity depends on temperature, using a finite element approach in the Petra-M workbench. A 2D density profile is then obtained from a prescribed density profile at the outer midplane assuming pressure is uniform along a flux tube in the SOL. This approach results in density and temperature profiles in which the strong asymmetric nature of heat conduction between the parallel and perpendicular background magnetic field is successfully captured. Furthermore, this work focuses on investigating the effect of the SOL plasma density profile on parasitic HHFW propagation in the SOL. The simulation results show that the radial gradient of the density profile affects the wavefield propagation in the SOL. As the density profile broadens, the wavefield intensity and its poloidal extent are reduced in the SOL, and the core coupling increases. Similarly, as shown by collisional power deposition, a proxy for power absorption, the fraction of power deposited in the SOL decreases with a broadening profile.

HHFW↗
DOE OSTI2021

Improvement in the spatial resolution of heavy ion beam probe measurements through application of ion optics

A technique for more accurately modeling and improving the spatial resolution of heavy ion beam probe measurements is described. We use a set of particle trajectories to numerically determine the focusing properties of a complicated three-dimensional magnetic field and characterize those properties with a transfer matrix. We then modify the transfer matrix approach of traditional ion optics to include a parameter that describes the ionization location of the detected ions. The ion optics model calculated using this technique enables a more accurate description of the particle trajectories than previously feasible. The model also allows one to easily determine an initial beam focus that could be used during experimental operation to optimize the spatial resolution of measurements. The technique has been applied to the design of a heavy ion beam probe diagnostic for the Wendelstein 7-X stellarator and improvements in the modeled spatial resolution by a factor of about 2 over previous estimates are possible. As a result, the improved spatial resolution will enable measurements of plasma fluctuations with smaller wavelengths than would otherwise be possible.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

Suppression and enhancement of electromagnetic pulses from laser–target interactions by strong magnetic fields

Laser–target interactions generate intense electromagnetic pulses (EMPs) that can interfere with measurements and damage equipment. In this paper we show that applying a magnetic field to nanosecond pulse laser–target interactions decreases the magnitude of EMPs. We demonstrate this effect in two experiments with different geometries (spherical versus planar), laser intensities ( ∼10 13 versus ∼10 15 W/cm 2 ) and applied field strength (12 versus 0.1 T) that both observed suppression of EMPs in approximately the 1 GHz band (by factors of 0.65× and 0.32×, respectively). We then observe the opposite effect at high intensities with a picosecond pulse: for planar experiments with laser intensities of approximately 10 19 W/cm 2 and magnetic fields of 6–10 T, the magnitude of EMPs is increased by a factor of 1.75×. These results provide a benchmark for models of EMP generation, but suggest that magnetic fields are not a viable solution for mitigating EMPs in the high-intensity laser facilities where they are most damaging.

electromagnetic pulse↗
DOE OSTI2025

Impact of ionization peak location on measured opaqueness in DIII-D H-mode plasmas

This study investigates the relationship between electron pedestal density and the location of the ionization peak on neutral penetration in DIII-D H-mode plasmas, utilizing a database of Lyman-α emission measurements. The high electron density leads to neutrals being ‘screened’ and the ionization front being pushed out into the Scrape-Off Layer (SOL). This is also referred to as the neutral opaqueness, which is heuristically expected to scale with edge plasma density and machine size. However, at lower electron pedestal density, the penetration depth of the neutrals varies, and measured opaqueness deviates from the heuristic scaling. The database reveals that at low density, when the ionization peak is located in SOL region, the linear relationship between the electron density and neutral penetration holds. However, when the peak is located inside the separatrix, the penetration of the neutrals (λ n 0 ) is much wider ~3.0–3.5 cm, breaking the heuristic opaqueness approximation. These findings provide valuable insights into fueling efficiency and plasma behavior, with implications for Fusion Pilot Plants where high pedestal densities are anticipated and where the neutral opaqueness behaves like its heuristic approximation. This analysis offers a framework to refine neutral opaqueness approximations, enhancing the predictive capability for advanced tokamak operations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Neural operator transformers capture bifurcating drift-wave turbulence in fusion plasma simulations

Self-consistent modeling of turbulence-driven transport is critical for optimizing confinement in magnetically confined fusion plasmas, such as tokamaks and stellarators. In particular, capturing the long-term co-evolution of turbulence, flow, and background plasma profiles remains computationally challenging. Direct numerical simulation of these multiscale, highly nonlinear processes is often demanding and impractical for real-time control or design optimization. To address this bottleneck, we investigate transformer-based neural operator partial differential equation surrogates for emulating the dynamics of drift-wave turbulence bifurcation mediated by zonal flows, using the modified Hasegawa–Wakatani (MHW) model as a prototypical system. We find that the finetuned neural operator model has excellent performance in capturing the multi-spatiotemporal-scales of MHW turbulence bifurcation and is robust to testing on rare and out-of-distribution dynamics. Specifically, we demonstrate that a single unified model accurately predicts both quasi-steady-state turbulence and a wide range of dynamical transition processes, such as nonlinear saturation, spontaneous suppression of turbulence, and the emergence of macroscopic zonal flows, over time horizons vastly exceeding the local turbulence correlation time. This computationally efficient approach establishes a strong foundation for fast, AI-based modeling of complex, multiscale phenomena in magnetized fusion plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Feasibility of main thermal ion heating by ICRF waves using a top launcher in a tokamak with deuterium–tritium plasmas

A scenario of ion cyclotron range of frequency (ICRF) wave injection from a top launcher is proposed as an efficient and direct heating method for thermal deuterium ions in deuterium–tritium tokamak plasmas. Positioned between the tritium cyclotron layer and ion–ion hybrid layer, the top launcher allows effective wave penetration to the ion–ion hybrid layer and enables significant power transfer to thermal deuterium. This is achieved through favorable wave polarization for fundamental cyclotron damping. There is a Doppler broadening around the cyclotron resonance and this overlaps with the ion–ion hybrid layer. Low toroidal mode numbers and ion temperature in the range of 5–20 keV are favorable for enhancing the main ion damping relative to electron damping. In contrast to the neutral beam injection, which penetration strongly depends on machine size and plasma density, the proposed ICRF-based direct ion heating scenario is shown to be scalable and applicable to both larger and smaller tokamak devices within practical constraints.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

In-situ spectroscopic ellipsometry for real-time characterization of the effects of high-flux helium plasmas on tungsten surfaces

Tungsten samples were exposed to He plasmas generated by an RF source (Γ i = 3.5 x 10 16 He cm -2 s -1 , ion energy = 92 eV.) The range of exposure conditions selected here is conducive to the growth of nearsurface He bubbles, and at higher fluence, the formation of W nanotendrils ranging between 50 — 100 nm in diameter. The evolution of these surface features was probed using a fixed-angle ellipsometer (280 — 1000 nm wavelength range) with direct line-of-sight to the sample. Over the parameter space explored here, changes in the two angles (p, S) that define the polarization of the reflected light followed a distinct trajectory with increasing plasma fluence. Ex-situ ellipsometry of 22 additional tungsten specimens tested at a wide range of plasma fluences and temperatures mapped onto these in-situ results well. We used helium ion microscopy and focused ion beam profiling to provide a direct calibration of the ellipsometry measurements. Our results indicate that for a reproducible process such as the growth helium-induced surface morphologies, ellipsometry is a practical in-situ diagnostic to study how fusion plasmas modify materials. To study more general effects of plasmas on surfaces, including co-deposition and sputtering, different approaches to modelling the optical properties of the exposed surfaces are also considered.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Introduction and overview: Chapter 1 of the special issue: on the path to tokamak burning plasma operation

The International Tokamak Physics Activity (ITPA) has developed a comprehensive overview of the results of its coordinated R&D activities in fusion physics and diagnostics implemented during the past two decades with the aim of developing an improved physics basis for the operation of tokamak burning plasma experiments. Here, an introduction is presented to key concepts in the physics of burning plasmas in tokamaks, together with an overview of the scope of the principal areas of physics R&D pursued by the ITPA Topical Physics Groups in which the critical issues, major areas of progress and most significant recent results are highlighted. This paper introduces the following collection of articles, which encompass detailed presentations of the progress achieved by the Topical Groups in preparing the physics basis for the operation of tokamak burning plasma experiments expected to come into operation in the 2030s.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

A database and meta-analysis on the performance of exploding pusher implosions conducted at OMEGA

A database of 222 exploding pusher implosions conducted at the OMEGA Laser Facility is presented. The dataset consists of glass-shell capsules filled with varying pressures of D 2 , T 2 , and 3 He, which were imploded using square laser pulses with intensities ranging from 1 to 1 × 10 15 W/cm 2 . The database includes measurements of bang times, ion temperatures, and yields from the DD, D 3 He, and DT fusion reactions. A semi-analytic exploding pusher model is introduced, which effectively captures the observed trends in the data. This model predicts that the measurements scale according to a power-law relation based on the initial capsule and laser conditions. A generalized power-law scaling relation is directly fit to each dataset, providing a useful interpolation of the entire database. Overall, the database provides a valuable resource to estimating bang times, temperatures, and yields for the design of future experiments. Additionally, it provides a diverse set of data for validating more advanced implosion physics models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

X-ray Lasers: The evolution from Star Wars to the table-top [PowerPoint]

X-ray lasers have evolved from a Star Wars missile defense system to a table-top research tool: (1) LLNL proposes X-ray laser schemes in the 1970’s, (2) First X-ray lasers demonstrated in early 1980’s were nuclear pumped, (3) Demonstrated the world’s shortest wavelength, highest energy laser, (4) First laboratory X-ray laser demonstrated on Novette in 1984, (5) A decade of progress using the Nova laser (5 kJ) from 1985 to 1996, (6) X-ray lasers produced at the COMET table-top facility (<10 J) since 1997, (7) X-ray lasers used for plasma interferometry and other applications, (8) 10 Hz X-ray laser at 18.9 nm demonstrated in 2004 using 0.15 J drive, (9) 100 Hz X-ray laser at 13.9 nm produces 1 µJ of saturated output using 0.9 J drive from diode-pumped optical laser in 2014.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

DOE Plasma Science Center - Predictive Control of Plasma Kinetics: Multi-Phase and Bounded Systems (Final Report DE-SC0001939)

Low temperature plasmas (LTPs) are the plasmas of electron-volt (eV) physics and eV technologies. LTPs have characteristic electron temperatures of a few eV and fractional ionizations that are typically small. Since LTPs have electron temperatures commensurate with the threshold energies of excited states in neutral atoms and molecules, power transfer from electrons to these atoms and molecules efficiently produces activated species (e.g., radicals, excited states, photons). Acceleration of ions in the sheaths of LTPs to energies of tens to hundreds of eV enable activation of surface modifying processes – sputtering, etching, deposition. With such properties, LTPs are often and beneficially used in technological devices, ranging from etching and deposition in microelectronics and solar cell fabrication, to hardening of surgical instruments. LTPs harbor fundamental science issues that are intellectually challenging and rewarding. At the same time, there are enormous societal benefits that are enabled by LTPs. The entire present-day and future information technology infrastructure owes its very existence to LTPs. Renewable energy sources, such as solar cell arrays, could not be economically produced in the absence of deposition and etching by LTPs. In acknowledgment of the importance of LTPs, the DOE Office of Fusion Energy Sciences supported the Plasma Science Center for Predictive Control of Plasma Kinetics: Multi-Phase and Bounded Systems from August 2009 to July 2021, consisting of an initial 5-year grant, 3 funded extensions and 2 no-cost extensions. This is the final report of the Center in which the productivity of the Center is discussed in terms of publications, impact and personnel. High-lights of the research performed in the Center are provided.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Plasma Photonics for the Control of Kilojoule Lasers

The main goal of this project was to develop plasma photonic devices (plasma lenses or ellipsoidal plasma mirrors (EPMs)) for controlling the focus of high-energy (kJ-class) laser systems. In order to defocus a kJclass laser beam, a plasma optic must produce a very specific plasma density profile. For a plasma lens, this profile must be peaked on axis and fall off parabolicly with radius. We developed four plasma-lens target designs that were predicted to yield the ideal plasma profile required for defocusing kJ-class laser beams. Particle-in-cell (PIC) simulations using the code OSIRIS were used to explore the design. The resulting plasma lens must also be underdense, which sets an upper limit on the solid density of the plasma-lens targets to ~ 1 mg/cm 3 or less. This low of a density is highly challenging to fabricate.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Reconstructing 3-D Asymmetries in Laser-Direct-Drive Implosions on OMEGA

Three-dimensional reconstruction algorithms have been developed which determine the hot-spot velocity, hot-spot apparent ion temperature distribution, and fuel areal-density distribution present in laser-direct- drive inertial confinement fusion implosions on the OMEGA laser. These reconstructions rely on multiple independent measurements of the neutron energy spectrum emitted from the fusing plasma. Measurements of the neutron energy spectrum on OMEGA are made using a suite of quasi-orthogonal neutron time-of-flight detectors and a magnetic recoil spectrometer. These spectrometers are positioned strategically around the OMEGA target chamber to provide unique 3-D measurements of the conditions of the fusing hot spot and compressed fuel near peak compression. The uncertainties involved in these 3-D reconstructions are discussed and are used to identify a new nTOF diagnostic line of sight which when built will reduce the uncertainty in the hot-spot apparent ion temperature distribution from 700 to <400 eV.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗