Search NASA⌕ Search

SEARCH · Search NASA

Results for “point of loads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Simple Formulas for Stagnation-Point Convective Heat Loads in Lunar Return

Simple formulas are given for the stagnation-point convective heat 1 loads in lunar return for two operational modes. The two modes of operation analyzed are typical of moderate heating and of nearly minimum heat loads, respectively. The values of the parameters in a simple two- parameter formula for the total-heat load are given in the lift-drag-ratio range of 0.2 to 1.0 and in the peak loading range of 2g to 10g. For vehicles having a lift-drag ratio near 0.5, which is typical of many proposed lunar return vehicles, the nominal mode had about 20 percent more absorption than the nearly minimum mode.

Grant, Frederick C.↗
NASA NTRS1992

Damage and failure mechanisms of continuous glass fiber reinforced polyphenylene sulfide

The damage that accompanies flexural deformation of a unidirectional glass fiber composite of polyphenylene sulfide was examined by AE and SEM. These complementary techniques were used to identify damage mechanisms at the microscale and correlate them with the macroscopic stress state in four-point bending. The flexural stress-strain curve was nominally linear to about 1.0 percent strain, but the onset of damage detectable by AE occurred at 0.3 percent strain. Two peaks in the AE amplitude distribution were observed at 35 dB and 60 dB. Low-amplitude events were detected along the entire length of the specimen, and correlation with direct observations of damage made by deforming the composite on the SEM stage suggested that these events arose from matrix cracking and fiber debonding concentrated at flaws on the composite. High amplitude events occurred primarily in the region of highest flexural stress between the inner loading points. They were attributed to fracture of glass fibers on the tension side and surface damage on the compressive side.

Chen, F.↗
NASA NTRS2016

A New Load Residual Threshold Definition for the Evaluation of Wind Tunnel Strain-Gage Balance Data

A new definition of a threshold for the detection of load residual outliers of wind tunnel strain-gage balance data was developed. The new threshold is defined as the product between the inverse of the absolute value of the primary gage sensitivity and an empirical limit of the electrical outputs of a strain{gage. The empirical limit of the outputs is either 2.5 microV/V for balance calibration or check load residuals. A reduced limit of 0.5 microV/V is recommended for the evaluation of differences between repeat load points because, by design, the calculation of these differences removes errors in the residuals that are associated with the regression analysis of the data itself. The definition of the new threshold and different methods for the determination of the primary gage sensitivity are discussed. In addition, calibration data of a six-component force balance and a five-component semi-span balance are used to illustrate the application of the proposed new threshold definition to different types of strain{gage balances. During the discussion of the force balance example it is also explained how the estimated maximum expected output of a balance gage can be used to better understand results of the application of the new threshold definition.

load residuals↗
NASA NTRS1962

SOME RECENT RESULTS ON THE BUCKLING MECHANISM OF SPHERICAL CAPS

The curve of pressure versus deformation for a spherical cap subjected to external pressure is frequently assumed to be similar to that of Fig. 1. Here P is a loading parameter and D(P) is a measure of the deformation (e.g. maximum displacement). This curve implies that for P > P(U) and for P < P(L) there is only one equilibrium state. For each P in P(L) < P < P(U) there are three equilibrium states and the cap must buckle at some P in this interval. We call P(L) and P(U), respectively, the upper and lower buckling loads. Points on the branch 0U correspond to unbuckled equilibrium states, those on the branch LN to buckled states and those on UL to unstable states.

BUCKLING↗
NASA NTRS1972

CSM docked DAP/orbital assembly bending interaction-axial case

A digital autopilot which can provide attitude control for the entire Skylab orbital assembly using the service module reaction control jets is described. An important consideration is the potential interaction of the control system with the bending modes of the orbital assembly. Two aspects of this potential interaction were considered. The first was the possibility that bending induced rotations feeding back through the attitude sensor into the control system could produce an instability or self-sustained oscillation. The second was whether the jet activity commanded by the control system could produce excessive loads at any of the critical load points of the orbital assembly. Both aspects were studied by using analytic techniques and by running simulations on the all-digital simulator.

Turnbull, J. F.↗
NASA NTRS1972

Elastic plate spallation

The dynamic finite element method was used to investigate elastic stress waves in a plate. Strain displacement and stress strain relations are discussed along with the stiffness and mass matrix. The results of studying point load, and distributed load over small, intermediate, and large radii are reported. The derivation of finite element matrices, and the derivation of lumped and consistent matrices for one dimensional problems with Laplace transfer solutions are included. The computer program JMMSPALL is also included.

Oline, L.↗
NASA NTRS1973

Design, process development, manufacture, test and evaluation of boron-aluminum for space shuttle components

The development of sufficient technology to permit application of boron-aluminum to space shuttle components is described. Specifically, report is made of the fabrication and testing of a 48 in. by 72 in. boron-aluminum compression panel capable of distributing a point load of 350,000 lbs. into a uniform running load within a peaking factor of 1.3 at a temperature of 600 F. In addition, small component testing was performed to verify the compression panel design.

Garrett, R. A.↗
NASA NTRS1973

Single stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors. Part 4: Data and performance for stage B

Stage B, composed of tandem-airfoil rotor B and stator B, was tested with uniform inlet flow and with hub radial, tip radial and 90 degree one-per-revolution circumferential distortion of the inlet flow as part of an overall program to evaluate the effectiveness of tandem airfoils for increasing the design point loading capability and stable operating range of rotor and stator blading. The results of this series of tests provide overall performance and blade element data for evaluating: (1) the potential of tandem blading for extending the loading limit and stable operating range of a stage representative of a middle stage of an advanced high pressure compressor, (2) the effect of loading split between the two airfoils in tandem on the performance of tandem blading, and (3) the effects of inlet flow distortion on the stage performance. The rotor had an inlet hub/tip ratio of 0.8 and a design tip velocity of 757 ft/sec. With uniform inlet flow, rotor B achieved a maximum adiabatic efficiency of 88.4% at design equivalent rotor speed and a pressure ratio of 1.31. The stage maximum adiabatic efficiency at design equivalent rotor speed with uniform inlet flow was 82.5% at a pressure ratio of 1.28. Tip radial and circumferential distortion of the inlet flow caused substantial reductions in surge margin.

Brent, J. A.↗
NASA NTRS1973

Crack toughness evaluation of hot pressed and forged beryllium.

Fracture toughness tests at room temperature were made on three-point loaded beryllium bend specimens cut from hot pressed block and a forged disk. These specimens had plane proportions conforming to ASTM E 399 and covered a thickness range of from 1/32 to 1/2 in. Two sets of bend specimens were tested, one having fatigue cracks and the other 0.5 mil radius notches. One objective of the investigation was the development of techniques to produce fatigue cracks in accordance with the procedures specified in ASTM E 399. This objective was achieved for the hot pressed material. In plane cracks were not consistently produced in the specimens cut from forged stock.

Jones, M. H.↗
NASA NTRS1973

Design, process development, manufacture, test and evaluation of boron-aluminum for space shuttle components

A multi phase boron-aluminum design and evaluation program for space shuttle components was conducted, culminating in the fabrication of a 1.22 m (48 inch) x 1.83 m (72 inch) boron-aluminum compression panel capable of distributing a point load of 1555 kN (350,000 lbs) into a uniform running load at a temperature of 589 K (600 F). This panel was of the skin-stringer construction with two intermediate frame supports; seven unidirectional stringers varied in thickness from 5 plies to 52 plies and the skin was contoured to thicknesses ranging from 10 plies to 62 plies. Both the stringers and the skin incorporated Ti-6Al-4V titanium interleaves to increase bearing and in-plane shear strength. The discrete program phases were materials evaluation, design studies, process technology development, fabrication and assembly, and test and evaluation.

Garrett, R. A.↗
NASA NTRS1975

A reciprocal theorem for a mixture of interacting continuous media

Using a linearized theory of interacting continuous media composed of linear elastic solid and linear viscous fluid, a reciprocal theorem is derived which relates the solution of one initial-boundary value problem to another. As an illustration of the reciprocal theorem, we obtain the early time displacement and velocity field of a mixture occupying an infinite region and subjected to an impulsively applied moving point load acting on the solid constituent.

Lee, Y. M.↗
NASA NTRS1976

Performance characteristics of a diesel engine using low- and medium-energy gases as a fuel supplement (fumigation)

The use of low- and medium-energy gases derived from solid waste is investigated. Gases that simulate those gases that could be derived from refuse were injected into the air inlet of a 298-kilowatt (400 horsepower) diesel engine as a fuel supplement. This process is called fumigation. Three different gases with thermal-energy contents of 6.11 MJ/cu m (164 Btu/cu ft), 18.1 MJ/cu m (485 Btu/cu ft), and 18.8 MJ/cu m (505 Btu/cu ft, respectively, were used at rates ranging as high as 20 percent of the normal fuel oil energy at four different engine load points. The test results indicated approximately 100 percent gas energy utilization with no observable deleterious effect on the engine.

Monford, L. G.↗
NASA NTRS1978

Global crustal response model

A computer program was developed for calculating the radial displacement due to the body tide as a function of spatial position and time. The positions of the moon and sun were evaluated by means of the Hill-Brown and Newcomb theories, respectively. Green's functions were utilized to simulate the elastic Earth responses due to point loads, a convolution program has been developed to evaluate the elastic Earth responses due to ocean loading by a given ocean tide constituent. These responses include radial and horizontal displacement, tilt and gravity acceleration, and strain tensor components.

Source record↗
NASA NTRS1980

Green's function for a crack emanating from a circular hole in an infinite sheet

Stress-intensity factors, K/I/ and K/II/, are obtained for a point loaded crack emanating from a circular hole in an infinite plate. A series approach and the Muskhelishvili formulation in the two-dimensional theory of elasticity are used to derive the solution. The applicability of the solution is demonstrated by using it as a Green's function to obtain K/I/ and K/II/ and the case of (1) biaxial tension of an infinite plate and (2) bending of a wide strip.

Shivakumar, V.↗
NASA NTRS1981

Computation of wind tunnel model deflections

The experimental deflections for a transport type solid wing model were measured for several single point load conditions. These deflections were compared with those obtained by structural modeling of the wing by using plate and solid elements of Structural Performance Analysis and Redesign (SPAR) program. The solid element representation of the wing showed better agreement with the experimental deflections than the plate representation. The difference between the measured and calculated deflections is about 5 percent.

Mehrotra, S. C.↗
NASA NTRS1981

Stress-intensity factors and crack-opening displacements for round compact specimens

An improved method of boundary collocation based on the complex variable analysis of Muskhelishvili (1953) is applied to the two-dimensional stress analysis of round compact specimens with pin-loaded holes. Stress intensity factors and crack opening displacements are calculated for various round compact specimens as a function of crack-length-to-specimen-width ratios. A wide-range equation for the stress intensity factors and equations for crack-surface displacements and load-point displacements are developed.

Newman, J. C., Jr.↗