Search NASA⌕ Search

SEARCH · Search NASA

Results for “precipitation strengthening”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Improved Creep and Tensile Properties of a Corrosion Resistant Ni-Based Superalloy Using High Temperature Aging and Nb/Ta Additions

Resistance to creep deformation is essential for cast and wrought Ni-based superalloys in next generation energy systems due to the considerable exposure times required at the operating temperature. Here the amount of precipitate strengthening was increased in variants to Inconel alloy 725 (IN725), a corrosion resistant alloy, to improve its elevated temperature mechanical strength. Additions of Nb or Ta coupled with a high temperature aging (HTA) heat treatment promoted the formation of γ" precipitates and grain boundary phases which led to significant increases in time to failure. The HTA increased the creep life of various alloy formulations as compared to the standard aging heat treatment with a maximum improvement of 371%. The Nb and Ta additions lowered the minimum creep rate (MCR) and had a similar effect on increasing creep life. The positive effect of the additions was more pronounced when coupled with the HTA which employed a higher temperature in the first step of the heat treatment to promote precipitate phase formation. The Ti/Al ratio was used to design alloys with preferential formation of ' or γ" precipitates. Compact morphology precipitates were formed in the alloys with a low Ti/Al ratio. While a low Ti/Al ratio was primarily associated with lower MCRs, the effect on the creep life was less evident than that of the HTA. By using additions of Nb or Ta and a HTA heat treatment, the creep life of IN725 for testing at 973 K (700 °C) and 483 MPa was improved by up to 256%.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Inhomogeneous Distribution and Coarsening of γ″ Precipitates in a Ni-Based Superalloy and Their Effect on Creep

γ″ was found to be the main precipitate strengthening phase with no detectable g′ in both M725 alloys. After creep, the grip/gage sections of the crept M725-Nb/Ta exhibited preferential coarsening and inhomogeneous distribution of g″ platelets, and sandwich-like structures, comprising of cubic γ′ precipitates with small γ″ discs on each facet. This g″ variant selection behavior taking place in the grip section with no stress applied was different from the typical stress-induced variant selection reported in previous literature.

Hung, Chang-Yu↗
DOE OSTI2024

Neutron Diffraction Residual Stress Study of a AA2219-T87 Self-Reacting Friction Stir Weld

2219-T87 is a precipitation hardenable aluminum-copper alloy which sees wide use in structural aerospace components. Thick panels of this alloy are joined via self-reacting friction welding (SRFSW); however, this thermomechanical process can result in significant loss of the alloy’s strengthening precipitates and large residual stresses which are detrimental to mechanical behavior and performance. High-resolution maps of the residual strain and stress states along the normal, transverse, and longitudinal directions of 2219-T87 SRFSW were obtained using neutron diffraction measurements. Residual stress had the highest tensile value in the heat-affected zone (HAZ) and the largest compressive stress in the base metal region of the normal and transverse directions. Line profile residual stress distributions displayed an “M”-shaped distribution in each direction with the longitudinal direction being the most pronounced while 2D residual stresses displayed an hourglass-shaped pattern. Further, average maximal longitudinal residual stress values ranged from 60.6 to 85.6% of yield. Microhardness testing across the transverse weld section produced a “V”-shaped curve with slight hardness recovery in the stir zone. Maximal and minimal microhardness values were observed in the base metal (154 HV) and thermomechanically affected zone (82 HV), respectively. Microstructural evolution was recorded using optical microscopy and showed decreasing grain size from the HAZ to the stir zone.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A strong and ductile Super Kovar alloy via fully coherent nanoprecipitates

Emerging high-precision technologies demand materials with exceptional dimensional stability and mechanical robustness, as even microscopic thermomechanical deformation can cause functional failure. However, a fundamental trilemma exists: High strength, ductility, and low thermal expansion are mutually exclusive, as strengthening-induced lattice distortions compromise the spin-lattice coupling, which is essential for low thermal expansion. Here, we overcome this trilemma by designing “Super Kovar,” an Fe-Ni-Co-Al-Ta alloy, featuring fully coherent nanoprecipitates. It unifies a 1.0-gigapascal ultimate tensile strength and ∼39% elongation with a Kovar-grade thermal expansion of 3.81 × 10−6 K−1 (100 to 410 K). The key is a dense dispersion of L12 nanoprecipitates that form an almost strain-free coherent interface with the ferromagnetic matrix. Beyond providing precipitation strengthening, these coherent interfaces suppress intrinsic phonons of nanoprecipitates via elastic coupling while avoiding magnetic domain pinning to preserve the Invar effect of the matrix. This reduces the thermal expansion of the precipitates by 56% and achieves a fourfold enhancement in the strength-ductility product, establishing a paradigm for dimensionally stable, ultrastrong alloys.

Yu, Chengyi [University of Science and Technology ↗
NASA NTRS1990

The mechanisms of dispersion strengthening and fracture in Al-based XD(tm) alloys, part 1

The influence of reinforcement size, volume fraction, and matrix deformation behavior on room and elevated temperature strength; the fracture toughness; and the fatigue crack growth rate of metal matrix composites of Al-4(pct)Cu-1.5(pct)Mg with TiB2 were examined. The influence of reinforcement volume fraction was also examined for pure aluminum with TiB2. Higher TiB2 volume fractions increased the tensile yield strength at both room and elevated temperatures, and reduced the elongation to fracture. Tensile tests also indicate that small particles provided a greater increase in strength for a given volume fraction than larger particles, whereas elongation to fracture appeared to be insensitive to reinforcement size. Interparticle spacing appears to be the factor that controls the strength of these alloys, with the exact nature of the dependence relying on the nature of dislocation slip in the matrix (planar vs. diffuse). The isothermal aging response of the precipitation strengthened Al-4(pct)Cu-1.5(pct)Mg alloys was not accelerated by the presence of TiB2. Cold work prior to artificial aging created additional geometrically necessary dislocations which serve as heterogeneous nucleation sites leading to accelerated aging, a finer precipitate size, and an increase in the strength of the alloy.

Aikin, R. M., Jr.↗
DOE OSTI2024

Inhomogeneous Distribution and Coarsening of y″ Precipitates in a Ni-Based Superalloy and Their Effect on Creep

It has been reported that the addition of Nb or Ta in the high Ti/Al ratio alloys promotes the formation of y″ precipitates solely and greatly contributes to the elevated temperature strength and resistance to creep deformation. In this study, the y''-dominant INCONEL alloy 725 (IN725) variants (named M725-Nb/Ta) modified with a high level of Nb/Ta additions and high Ti/Al ratio was chosen as a model alloy for microstructural observation of y'' variants upon creep. Following the high temperature aging (HTA), y'' was found to be the main strengthening precipitate with no detectable y’ in both M725 alloys. After creep, the grip/gage sections of the crept M725-Nb/Ta exhibited preferential coarsening and inhomogeneous distribution of y''. That is, one or two of the variants were preferentially coarsened at the expense of another variant, and sandwich-like structures, comprising of cubic y′ precipitates with small y″ discs on each face, were formed. This variant selection behavior taking place in the grip section with no stress applied was different from the typical stress-induced variant selection in previous literature. However, the sample with prior high temperature exposure (700 °C for 500 hours) with varying y″ characteristics demonstrated a similar trend of creep when compared with those in the HTA sample, suggesting that the coarsening and the inhomogeneous distribution of y'' was not the determinant of creep life in bulk M725-Nb/Ta alloys.

Hung, Chang-Yu↗
DOE OSTI2020

Strategies for simultaneous strengthening and toughening via nanoscopic intracrystalline defects in a biogenic ceramic

While many organisms synthesize robust skeletal composites consisting of spatially discrete organic and mineral (ceramic) phases, the intrinsic mechanical properties of the mineral phases are poorly understood. Using the shell of the marine bivalve Atrina rigida as a model system, and through a combination of multiscale structural and mechanical characterization in conjunction with theoretical and computational modeling, we uncover the underlying mechanical roles of a ubiquitous structural motif in biogenic calcite, their nanoscopic intracrystalline defects. These nanoscopic defects not only suppress the soft yielding of pure calcite through the classical precipitation strengthening mechanism, but also enhance energy dissipation through controlled nano- and micro-fracture, where the defects’ size, geometry, orientation, and distribution facilitate and guide crack initialization and propagation. These nano- and micro-scale cracks are further confined by larger scale intercrystalline organic interfaces, enabling further improved damage tolerance.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Leveraging Solute Segregation in Laser Powder Bed Fusion to Achieve Superior Strength and Ductility Via Single-Step Heat Treatment in Ti-Free Grade 300 Maraging Steel

Maraging steels are Fe-Ni precipitation-strengthened steels that can be heat treated for achieving high strength with an accompanying loss in ductility, a trend common to most metals. Here, we show that the segregation of Ni during laser powder bed fusion, commonly considered a nuisance that is dealt with via solutionizing heat treatments, can be leveraged via direct aging to achieve higher strength and ductility simultaneously, compared to a solutionized and aged condition. The high dislocation density in combination with solute segregation in the as-fabricated material promotes the precipitation of Mo-rich intermetallic phases that are responsible for the high strength, and the Ni segregated regions facilitate austenite reversion during direct aging. The reverted austenite enhances the elongation via transformation-induced plasticity. While overcoming the strength–ductility conundrum, direct aging can significantly reduce the energy and emissions associated with multistep heat treatments, especially in the global tool and die industry, while laser powder bed fusion (LPBF) can enable tools with integrated cooling channels for increased downstream production efficiency.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Development of Novel Ferritic-Martensitic Steels with Superior Creep Properties for Power Plant Applications

A creep resistant martensitic steel, CPJ-7, was developed with an operating temperature approaching 650°C. Subsequently, another creep resistant martensitic steel, JMP, was designed with the potential to operate at, or slightly above, 650°C. This report describes the development of these alloys from early iterations of CPJ steels to the final CPJ-7 formulation as well as the more heat resistant JMP steel formulation. The design originated from computational modeling for phase stability and precipitate strengthening using fifteen constituent elements. Approximately forty heats of CPJ and ten of JMP, each weighing ~7 kg, were vacuum induction melted. A computationally optimized heat treatment schedule was developed to homogenize the ingots prior to hot forging and rolling prior to final normalization and tempering. Overall, wrought and cast versions of CPJ-7 present superior creep properties when compared to wrought and cast versions of COST alloys for steam turbine and wrought and cast versions of P91/92 for boiler applications. For instance, the Larson Miller Parameter curve for CPJ-7 at 650°C almost coincides with that of COST E at 620°C. The prolonged creep life was attributed to slowing down the process of the destabilization of the MX and M 23 C 6 precipitates at 650°C. On the other hand, the cast version of CPJ-7 also revealed superior mechanical performance, well above commercially available cast 9% Cr martensitic steel or derivatives, especially for creep life at 650°C. The casting process employed slow cooling to simulate the conditions of a thick wall full-size steam turbine casing but utilized a separate homogenization step prior to final normalization and tempering. To advance the development of CPJ-7 for commercial applications, a process was used to scale up the production of the alloy using vacuum induction melting (VIM) and electroslag remelting (ESR), which underlined the importance of melt processing control of intentionally designed minor and trace elements in these advanced alloys. Following the work on CPJ-7, the JMP steels were designed with higher Co for increased solid solution strengthening, Si for oxidation resistance and increased W (with low Mo content) for matrix strength and stability as well as solid solution strengthening. The JMP steels showed increases in creep life compared to CPJ-7 between 118 to 150% at 650°C for testing at various stresses between 138 MPa and 207 MPa. On a Larson-Miller plot, the performance of the JMP steels surpasses that of state-of-the-art MARBN and other MARBN-type steels. The influence of various elements within the composition of the alloys on the microstructure and mechanical properties are discussed. This report presents approximately 420,000 h of in-house creep testing, the equivalent of almost 50 years of cumulative creep tests.

36 MATERIALS SCIENCE↗
NASA NTRS1990

The Mechanisms of Dispersion Strengthening and Fracture in Al-based XD (TM) Alloys

The influence of reinforcement size, volume fraction, and matrix deformation behavior on room and elevated temperature strength, and the fracture toughness of metal matrix composites of both pure aluminum and Al(4 percent)Cu(1.5 percent)Mg with 0 to 15 vol percent TiB2 were examined. Higher TiB2 volume fractions increased the tensile yield strength both at room and elevated temperatures, and reduced the elongation to fracture. Tensile tests also indicate that small particles provided a greater increase in strength for a given volume fraction than larger particles, whereas elongation to fracture appeared to be insensitive to reinforcement size. The fracture toughness of the Al(4 percent)Cu(1.5 percent)Mg alloys decreased rapidly with TiB2 additions of 0 to 5 vol percent and more slowly with TiB2 additions of 5 to 15 vol percent. Fracture toughness appears to be independent of TiB2 particle size. The isothermal-aging response of the precipitation strengthened Al(4 percent)Cu(1.5 percent)Mg alloys was not altered by the presence of TiB2.

Aiken, R. M., Jr.↗
NASA NTRS1977

The effect of microstructure and strength on the fracture toughness of an 18 Ni, 300 grade maraging steel

Fractography and metallographic sectioning were used to investigate the influence of microstructure and strength on the fracture toughness (KIc) and fracture mechanism of an 18 Ni, 300 grade maraging steel. Increased yield strength from 1442 to 2070 MN/m squared through precipitation hardening results in a KIc loss from 143 to 55 MN/m superscript 3/2. Ti (C,N) Ti2S, and TiC inclusions in sizes from 1 to 8, 1 to 15, and 0.1 to 2 microns respectively serve as sites for void nucleation and lead to fracture by the dimpled rupture process in all strength levels considered. TiC nucleated dimples occupy more than half the fracture in all conditions. Void nucleation rate and resultant number of dimples per unit area of fracture increase with increasing yield strength. Average dimple size decreases with increasing strength and/or overaging which follows from the decreasing amount of stable void growth measured by sectioning tensile specimens. Void growth is assisted by crack branching along a path of TiC inclusions. Coalescence occurs in the highest strength materials by a combination of TiC void nucleation and premature separation at strengthening precipitates.

Psioda, J. A.↗
DOE OSTI2021

The role of Si in determining the stability of the θ; precipitate in Al-Cu-Mn-Zr alloys

Precipitate-strengthened Al-Cu-Mn-Zr (ACMZ) alloys demonstrate improved microstructural stability compared to conventional Al-Cu alloys. Si is typically considered an impurity in these alloys, but a systematic analysis of ACMZ alloys with a range of Si levels revealed that there is a Si content range (~0.05 wt. % < Si < ~0.10 wt. %) for achieving optimal high temperature microstructural stability. A combination of hardness testing, scanning electron microscopy, and atom probe tomography has been used to understand the relationship between Si content, aging response, and thermal stability in ACMZ alloys. It is shown that the optimum Si content range corresponds to a reduced as-aged hardness, but a greater hardness value retained by the alloy after thermal exposure to 350 °C for 200 hours. A mechanism is proposed in which optimum Si levels reduce the number density of nucleation sites for θ' precipitates, resulting in larger precipitates that, on average, provide a reduced as-aged strength but are more coarsening resistant. This inherent θ' coarsening resistance allows more time for slow-diffusing Mn and Zr to reach the θ' interface and further stabilize the precipitates. Designing the optimal as-aged microstructure for improved thermal stability of the alloy by controlling impurity levels is a concept that has implications beyond the investigated Al-Cu alloy system.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Metastable formation and disordering kinetics of body-centered orthorhombic CrNi 2 laths in a Cr-Ni binary alloy

Chromium (Cr) alloys combine low density with high-temperature strength but suffer from brittleness and rapid softening. Body-centered orthorhombic (BCO) CrNi 2 laths have been shown to improve Cr-alloy high-temperature strength retention, yet their thermal stability and transformation behavior remain unclear. CrNi 2 conventionally forms through long-range ordering from a face-centered cubic (FCC) phase. Using multiscale microscopy and neutron diffraction, we show that CrNi 2 instead nucleates from a body-centered cubic (BCC) matrix, in a binary Cr 85 Ni 15 alloy. Despite aging above the equilibrium ordering temperature, CrNi 2 persists for ∼220 h at 760 °C before fully disordering, indicating sluggish transformation kinetics. The formation and decomposition follow differing transformation pathways (BCC → CrNi 2 → FCC), revealing kinetic asymmetry not captured by equilibrium Cr-Ni phase diagrams. In conclusion, these findings redefine the transformation behavior of CrNi 2 , establish its metastable kinetic window, and suggest alloying strategies to stabilize CrNi 2 for precipitation strengthening of high-temperature Cr-alloys.

CrNi2 transformation kinetics↗
DOE OSTI2021

Effect of heterogeneous microstructure on the tensile and creep performances of cast Haynes 282 alloy

Precipitation-strengthened Ni-based superalloys are leading candidate materials for advanced ultra-supercritical (A-USC) plants with steam conditions up to 760 °C (1400 °F) and 35 MPa (5 ksi). This study evaluates representative specimens from a large casting of Haynes 282 to study the effect of microstructural heterogeneity on the mechanical behavior of this alloy. The tensile test results of cast Haynes 282 over the temperature range 20–816 °C exhibited lower tensile strength and ductility in comparison with the reference wrought Haynes 282. However, the creep rupture tests of the cast alloy below 704–788 °C and 190–431 MPa presented a similar stress-Larson-Miller parameter to that of the wrought material. Microstructural and dislocation characterizations using scanning electron microscopy, conventional transmission electron microscopy, and scanning transmission electron microscopy in conjunction with energy dispersive X-ray spectroscopy were performed to understand the microstructural evolution before and after the mechanical tests. The heterogeneous microstructures of the cast Haynes 282 material, including the coarse grains, potential casting defects, and a bimodal size distribution of γ' precipitates, were detrimental to the tensile behavior, whereas the coarse-scale grains had a positive effect on the creep performance because diffusional creep was the dominant creep mechanism.

tensile testing↗
NASA NTRS2014

Fabrication of Turbine Disk Materials by Additive Manufacturing

Precipitation-strengthened, nickel-based superalloys are widely used in the aerospace and energy industries due to their excellent environmental resistance and outstanding mechanical properties under extreme conditions. Powder-bed additive manufacturing (AM) technologies offer the potential to revolutionize the processing of superalloy turbine components by eliminating the need for extensive inventory or expensive legacy tooling. Like selective laser melting (SLM), electron beam melting (EBM) constructs three-dimensional dense components layer-by-layer by melting and solidification of atomized, pre-alloyed powder feedstock within 50-200 micron layers. While SLM has been more widely used for AM of nickel alloys like 718, EBM offers several distinct advantages, such as less retained residual stress, lower risk of contamination, and faster build rates with multiple-electron-beam configurations. These advantages are particularly attractive for turbine disks, for which excessive residual stress and contamination can shorten disk life during high-temperature operation. In this presentation, we will discuss the feasibility of fabricating disk superalloy components using EBM AM. Originally developed using powder metallurgy forging processing, disk superalloys contain a higher refractory content and precipitate volume fraction than alloy 718, thus making them more prone to thermal cracking during AM. This and other challenges to produce homogeneous builds with desired properties will be presented. In particular, the quality of lab-scale samples fabricated via a design of experiments, in which the beam current, build temperature, and beam velocity were varied, will be summarized. The relationship between processing parameters, microstructure, grain orientation, and mechanical response will be discussed.

oxidation↗
DOE OSTI2023

Compatibility of Wrought Superalloys with Supercritical CO2

Supercritical CO2 (sCO2) power cycles, particularly direct-fired cycles, have the possibility of revolutionizing clean fossil energy with peak temperatures above 700 °C and wrought precipitation strengthened alloys like Haynes 282™ for structural components. At temperatures <650 °C, it would be desirable to use less expensive alloys, however, steels are known to be susceptible to carburization. Laboratory 300 bar sCO2 autoclave results were collected on a range of alloys including less expensive Ni-based alloys like 825 compared to advanced austenitic steels like alloy 709 at 600 °C. Both alloys 825 and 709 formed thin, protective Cr-rich oxides after 1,000 h. Alloy 825 also was exposed for 1,000 h in sCO2 at 800 °C and compared to a range of Ni-based alloys. Comparing alloys 625, 825, and 282, the mass gain increased with increasing alloy Ti content under these conditions. High Al superalloys did not perform significantly better under these conditions at 800 °C.

Pint, Bruce↗
DOE OSTI2022

Effect of microstructure on fatigue crack propagation in additive manufactured nickel-based superalloy Haynes 282: an experiment and crystal plasticity study

Haynes 282 is a γ' precipitation-strengthened nickel-based superalloy known for its exceptional high-temperature creep resistance and excellent fabricability. Recent advancements in powder-bed fusion-based additive manufacturing (PBF-AM) have enabled the fabrication of Haynes 282 with accurate, site-specific control of the grain orientation and morphology at the microscale. This ability opens up new avenues for microstructure design, to improve the material’s fatigue crack resistance and service life. This paper investigates the fatigue crack growth behavior of hybrid microstructure Haynes 282 fabricated via PBF-AM. Previous experiments revealed a higher crack propagation rate in the coarse columnar-grained microstructural regions when compared against fine-grained areas. Here, a strain gradient crystal plasticity model was adapted to study the fracture-related mechanical fields at the crack tip in the two microstructures. The simulation results showed a consistent influence of grain structure and texture on crack propagation, as was seen in the experiment. The model analysis revealed higher crack propagation driving force along crack direction in the coarse-grained sharply textured microstructure and higher driving force for crack kinking in fine-grained more diffusely textured microstructure, which is ascribed to the combined effect of yield stress, hardening rate, texture and grain morphology. The presented modeling approach will facilitate the development of the AM-based accurate microstructure design by deepening the fundamental study in AM-specific microstructure-properties relations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Differences in Oxidation Behavior of Conventionally Cast and Additively Manufactured Co-Base Alloy MAR-M-509

High-temperature oxidation behavior of conventionally cast and additively manufactured (AM) Co-base alloy MAR-M-509 was compared in the present study. The specimens were exposed in air at 1000 °C and characterized by means of scanning electron microscopy equipped with energy/wavelength dispersive x-ray spectroscopy (EDX/WDX) and electron backscatter diffraction as well as transmission electron microscopy. Substantial differences in the oxidation processes of two alloy versions were observed. Faster oxidation of the cast alloy was mainly induced by (1) oxidation of coarse primary carbides, (2) internal oxidation and nitridation processes and (3) incorporation of other alloy constituents (e.g., Co, Ni, W) into the Cr-oxide scale. AM specimens, in contrast, formed a more homogeneous, thinner and better adherent external oxide scale. The results are discussed in terms of differences in the chemical composition and alloy microstructure, including the grain size distribution in the material and the morphology of the strengthening precipitate phases.

36 MATERIALS SCIENCE↗