Search NASA⌕ Search

SEARCH · Search NASA

Results for “pressure plate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Forces and pressures induced on circular plates by a single lifting jet in ground effect

NASA Ames is conducting a program to develop improved methods for predicting suckdown and hot-gas ingestion on jet V/STOL aircraft when they are in ground effect. As part of that program a data base is being created that provides a systematic variation of parameters so that current empirical prediction procedures can be modified. The first series of tests in this program is complete. This report is one of three that presents the data obtained from tests conducted at Lockheed Aeronautical Systems - Rye Canyon Facility and the High Bay area of the 40 by 80 foot Wind Tunnel at Ames Research Center. Suckdown on two circular plates is examined.

Bellavia, David C.↗
NASA NTRS1974

Effects of flanges on pressure distribution on a flat plate and on a corrugated surface at Mach numbers from 0.60 to 1.97

An 8 by 6 foot supersonic wind tunnel was used to obtain the static pressure distribution on a plate in the region of a flange placed normal to the airstream. Tests were conducted on both a flat plate surface and a corrugated surface using flange heights ranging from 10 to 125 percent of the boundary layer height. Data were obtained at a zero degree angle-of-attack and at Mach numbers from 0.60 to 1.97.

Johns, A. L.↗
NASA NTRS1942

Square plate with clamped edges under normal pressure producing large deflections

A theoretical analysis is given for the stresses and deflections of a square plate with clamped edges under normal pressure producing large deflections. Values of the bending stress and membrane stress at the center of the plate and at the midpoint of the edge are given for center deflections up to 1.9 times the plate thickness. The shape of the deflected surface is given for low pressures and for the highest pressure considered. Convergence of the solution is considered and it is estimated that the possible error is less than 2 percent. The results are compared with the only previous approximate analysis known to the author and agree within 5 percent. They are also shown to compare favorably with the known exact solutions for the long rectangular plate and the circular plate.

PLATES-PRESSURE↗
NASA NTRS1991

High Reliability Robot Friendly ORU Interface

Presented here is a robot friendly coupling device for an orbital replacement unit (ORU). The invention will provide a coupling that is detached and attached remotely by a robot. The design of the coupling must allow for slight misalignments, over-torque protection, and precision placement. This is accomplished by means of a triangular interface comprising three components. A base plate assembly is located on an attachment surface, such as a satellite. The base plate assembly has a cup member, a slotted member, and a post member. The ORU that the robot attaches to the base plate assembly has an ORU plate assembly with two cone members and a post member which mate to the base plate assembly. As the two plates approach one another, one cone member of the ORU plate assembly has to be placed accurately enough to fall into the cup member of the base plate assembly. The cup member forces alignment until a second cone falls into a slotted member which provides final alignment. A single bolt is used to attach the two plates. Two deflecting plates are attached to the backs of the plates. When pressure is applied to the center of the deflecting plates, the force is distributed preventing the ORU and base plates from deflecting. This accounts for precision in the placement of the article. The novelty is believed to reside in using deflecting plates in conjunction with kinematic mounts to provide distributed forces to the two members.

Voellmer, George M.↗
NASA NTRS1992

High-Repeatability, Robot Friendly, ORU Interface

A robot-friendly coupling device for an Orbital Replacement Unit (ORU). The invention will provide a coupling that is detached and attached remotely by a robot. The design of the coupling must allow for slight misalignments, over torque protection, and precision placement. This is accomplished by using of a triangular interface having three components. A base plate assembly is located on an attachment surface, such as a satellite. The base plate assembly has a cup member, a slotted member, and a post member. The ORU that the robot attaches to the base plate assembly has an ORU plate assembly with two cone members and a post member which mate to the base plate assembly. As the two plates approach one another, one cone member of the ORU plate assembly only has to be placed accurately enough to fall into the cup member of the base plate assembly. The cup forces alignment until a second cone falls into a slotted member which provides final alignment. A single bolt is used to attach the two plates. Two deflecting plates are attached to the backs of the plates. When pressure is applied to the center of the deflecting plates, the force is distributed preventing the ORU & base plates from deflecting. This accounts for precision in the placement of the article.

Voellmer, George M.↗
NASA NTRS2021

Numerical Simulation of Pressure-induced Separation of Turbulent Flat-plate Boundary Layers: Definition and Overview of New Cases with Suction-only Transpiration and a Step in Reynolds Number

Results from two new direct numerical simulations (DNSs) are added to the database described in Coleman, Rumsey & Spalart (2018) (henceforth CRS18), and available at the NASA TMR website (https://turbmodels.larc.nasa.gov). The new flows, Cases D and E, are similar to the earlier ones (Cases A–C) in that a transpiration profile above a flat plate creates a prolonged adverse pressure gradient (APG) that drives a canonical turbulent zero-pressure-gradient (ZPG), flat-plate boundary layer towards separation; they differ in that for the new cases (1) the APG is not followed by a favorable gradient (FPG), since only suction transpiration is employed, and (2) the mean shear stress does not cross zero, so that the width of the mean bubble, strictly defined, is essentially zero. However, the probability of reversed skin friction exceeds 49%. The motivation was to produce a flow that is more akin to technological flows, including shock-boundary-layer interaction, with a gradual turbulence-controlled recovery. One of the new simulations is also at a significantly higher Reynolds number than the earlier flows.

Turbulence↗
NASA NTRS1973

Nonlinear response of plates subjected to inplane and lateral pressure pulses.

The nonlinear response of a rectangular plate exposed to a far-field sonic boom disturbance is studied. The plate is subjected to both lateral and in-plane disturbances. The lateral disturbance is in the form of an N-shaped pressure pulse, and the in-plane disturbance is represented by a sinusoidal pulse. The equations of motion are reduced to a set of nonlinear coupled ordinary differential equations using Galerkin's method. These equations are solved numerically using Hamming's (1959) modified predictor-corrector integration method. The effects of in-plane boundary conditions and in-plane inertia are investigated. The nonlinear results, when compared to the linear theory, serve to delineate the realm of validity of the linear theory.

Knapp, L. J.↗
DOE OSTI2020

Involute Working Group – Development and Validation of the Finite Element Models of the Cheverton-Kelley Experiments

In an involute-plate reactor, the fuel plates and side-plates are subjected to a non-uniform distribution of loads. Temperature variation derives from a variation in power distribution throughout the core. Due to small imperfections in the channel thickness, the coolant flowing in between the plates produces pressure differentials with a non-uniform distribution on the plate surface. The main goal of the analysis presented in this technical report is to investigate the ability of the commercial software STAR-CCM+ to model deformation of involute plates subjected to mechanical and thermal loads, representative of involute reactor operation conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Simulations of effects of fiber rigidity on wet press

A previously developed lattice-Boltzmann lattice-spring method is applied to simulate a wet press process. In simulations, multi-individual flexible fibers are settled on a wire screen by the force of gravity, and a fiber network is formed on the top surface of the wire screen. Next, the coordinates and velocities of fluid and fiber solid particles are copied to a computer press simulator composed of two perforated plates. A pressure pulse is imposed at the fluid contact line of the two press plates. Water is squeezed out of the fiber network by the pressure. Finally, during simulations, fiber rigidity, fiber concentrations, and pressure pulses are varied and their effects on water removal and re-wet phenomena are systematically studied.

42 ENGINEERING↗
NASA NTRS1962

Pressure Distribution Induced on a Flat Plate at a Free-Stream Mach Number of 1.39 by Rockets Exhausting Upstream and Downstream

An experimental investigation was made of the pressures induced on a flat plate at a free-stream Mach number of 1.39 by a supersonic rocket jet exhausting upstream and downstream. Measurements of the pressure distribution on a flat plate were made at zero angle of attack for 11 different locations of the jet exhaust nozzle beneath the wing. Measurements were made at ratios of rocket-exit total pressure to freestream static pressure from 6 to 60 and at a Reynolds number per foot of approximately 10 x 10 6 . The rocket when exhausted upstream produced a strong shock that moved further upstream with increasing rocket-exit total-pressure ratio. Positive incremental normal-force coefficients were obtained at all test positions. Data at 11 test positions are tabulated for rocket-on and rocket-off pressure coefficients as well as for incremental pressure coefficients for the 48 orifices of the flat plate for the range of ratio of rocket-exit total pressure to free-stream static pressure of the investigation. Changing the location of the model with respect to the plate had a negligible effect when the rocket was varied in the chordwise direction, but the pressure coefficients were reduced as the rocket was lowered away from the flat-plate wing.

Supersonic jet↗
NASA NTRS1942

Square plate with clamped edges under normal pressure producing large deflections

A theoretical analysis is given for the stresses and deflections of a square plate with clamped edges under normal pressure producing large deflections. Values of the bending stress and membrane stress at the center of the plate and at the midpoint of the edge are given for center deflections up to 1.9 times the plate thickness. The shape of the deflected surface is given for low pressures and for the highest pressure considered. Convergence of solution is considered and it is estimated that the possible error is less than 2 percent. The results are compared with the only previous approximate analysis known to the author and agrees within 5 percent. They are also shown to compare favorably with the known exact solutions for the long rectangular plate and the circular plate.

Levy, Samuel↗