Search NASA⌕ Search

SEARCH · Search NASA

Results for “printed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Grayscale projection two-photon lithography using sub-diffraction motifs for ultrafast and precise nanoscale 3D printing

Rapid and high-fidelity nanoscale 3D printing is highly desirable, but it is difficult due to the tradeoff between speed and accuracy. Although optical projection techniques can massively scale up printing, fidelity is compromised due to the difficulty in precisely controlling the light dosage over the entire field. This challenge is typically addressed by using multiple projections, but it slows down printing. Here, we present grayscale projection two-photon lithography to overcome this tradeoff. Despite using a binary mask, it enables projecting more than 15,000 focal spots, each with independently tunable intensity. It advantageously leverages constraints imposed by optical diffraction to achieve grayscale tuning over the entire field at once. By directly tuning the focal spot intensities, we demonstrate suppression of proximity effects, compensation of non-uniform illumination, compensation of stitching artefacts, and rapid 3D printing with a single femtosecond pulse per layer. We demonstrate printing of nanowires as thin as 55 nm and achieve rates of 1.7 billion voxels/s and 215 mm 3 /hr.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Printed Electrochemical Sensor for Quantifying Bone Density Loss in Microgravity

Printed electrochemical biosensors have been developed for astronaut point-of-care testing. Our fabrication approach is complimentary with in-space manufacturing for an on-demand and hands-free fabrication process. These sensors are developed using a combination of thin film materials printing and 3D printing and are comprised of carbon nanotube, gold nanoparticle, silver nanoparticle and dielectric inks to make traditional electrochemical sensor devices. Initial prototyped printed electrochemical sensors demonstrate good electrochemical performance while also displaying low batch to batch variability. Here we report the development of a printed sensor to monitor bone turnover. The absence of load bearing forces experienced in microgravity causes a reduction of overall bone mass and results in the development of space osteopenia/osteoporosis.(1,2) Our approach to identify space osteopenia/osteoporosis is to monitor the change in bone mass indirectly through an excreted biomarker of bone remodeling, amino-terminal collagen crosslinks (NTX). Antibodies specific to NTX are added to the sensor’s electrode ink and applied during the manufacturing process. NTX is measured from a urine sample by changes in voltammetry and electrochemical impedance as it binds to the antibody modified electrode surface. The measurement is rapid, quantitative and requires only small handheld electronics to perform the measurement. By this process, ground and flight physicians will receive frequent and real-time insight into the development of space osteopenia/osteoporosis to guide appropriate countermeasures. REFERENCES [1] Nabavi, N. et al (2011) Bone 49, 965-974. [2] Tamma, R. et al (2009) FASEB J 23, 2549-2554.

in-space manufacturing↗
NASA NTRSDate not supplied

Toward Fully 3D-Printed Two Degree of Freedom Acoustic Liners

An acoustic liner optimization tool is developed for designing two degree of freedom (2DOF) liners with high absorption over a wide range of frequencies and sound pressure levels (SPLs). Two additively manufactured 2DOF liners (one constant and one variable chamber depth) are designed and printed with an embedded perforate layer as the septum. A normal incidence impedance tube study is performed to directly compare impedance and absorption spectra to a more traditionally manufactured 2DOF liner with embedded mesh caps in phenolic honeycomb. Comparisons of test data to predictions are shown as well as SPL sensitivities for each acoustic liner. Broadband absorption is achieved with the 3D printed 2DOF liner containing constant chamber depths, although due to current limitations in printed embedded perforate hole size, not as broad as the traditional mesh cap liner. However, results also show that the 3D printed variable chamber depth sample is more comparable to the mesh cap liner absorption, demonstrating the viability of printed embedded perforates in novel concepts.

acoustic liner 2DOF two degree of freedom 3D print↗
DOE OSTI2025

All 2D Material Printed Diodes and Circuits on Paper for Sustainable Electronics

Sustainable electronics aim to reduce environmental impact by using ecofriendly materials, energy-efficient manufacturing, and recyclable components. However, existing approaches rely on complex, resource-intensive methods, rare metals, or nanomaterials with limited stability as well as plastic substrates, raising sustainability issues. Solution-processed two-dimensional (2D) materials offer a promising alternative: water-based and biocompatible conductive, semiconductive, and insulating 2D material inks can be produced with scalable techniques and are suitable for the fabrication of fully printed devices on low-cost and biodegradable paper substrates. However, 2D material only and fully printed diodes on paper have not yet been reported. Here, we demonstrate fully inkjet-printed 2D material-based diodes on paper using metal-insulator-semiconductor and metal-insulator-metal-semiconductor architectures. Water-based graphene and MoS2 inks, prepared by liquid-phase exfoliation, are used for the metallic and insulating films, while electrochemical exfoliation is used to produce the semiconducting MoS2 ink. The highest forward-to-reverse current ratio obtained is 330 (at ±2 V), while the forward current density is 1 mA/cm2 (at 1 V), making the diode performance comparable to the best solution-processed diodes reported so far. However, in contrast to previous works, fabrication occurs entirely at room temperature and ambient pressure, without using high-pressure sputtering, thermal evaporation, and any precious metal ink. The devices maintain stable performance under bending up to strain of 4% over 10,000 cycles. Finally, the diodes are successfully integrated with other 2D-material based electrical components to realize fully printed RC circuits, differentiators, integrators, and AC-to-DC converters onto paper, hence demonstrating the suitability of our approach for sustainable and disposable integrated circuits.

2D materials↗
DOE OSTI2025

High-resolution 3D-printed plastic scintillators with tertiary dye

Additive manufacturing offers efficient production of plastic scintillators with nontrivial geometries using vat polymerization, allowing fabrication of geometries which would be difficult or even impossible to produce using conventional subtractive manufacturing. This work presents a novel photocurable scintillator formula that includes coumarin 450 as a tertiary dye to enable high-resolution 3D printing via the manipulation of the 405 nm cure light. Bulk photocured and 3D printed (with and without tertiary dye) samples were compared through observational assessment and spectral response. All samples showed pulse shape discrimination between neutron and gamma events. Inclusion of the tertiary dye has minimal impact on emission spectrum and light output, but significant impact on print resolution as shown by comparison of printed high-complexity geometries and feature resolution test objects. With the use of a cure-limiting dye, unsupported features — such as freestanding pillars — were resolvable down to 0.7 mm. Even finer resolution at or below 0.1 mm was achieved in fully supported, integrated structures printed with off-the-shelf 405 nm desktop 3D printer. Scintillators demonstrated a light output up to 50% of EJ-200 with a PSD figure of merit up to 1.35 at 0.9–1.1 MeVee.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Adhesion Testing of Direct-Write Printed Ink on Metallic Structural Components

The successful adoption of additive manufacturing for the rapid prototyping of direct-write printed electronics requires the establishment of quantifiable metrics that can interrogate device performance. One measure of performance is the adhesion strength between the substrate and printed film interface, which is critical since the strength of this interface can dictate the accuracy and reliability of the printed device. In this work, a non-contact laser-induced spallation technique was used to quantify the adhesion of silver printed films on aluminum alloy substrates. The laser-based method was compared to a standardized pull-off adhesion test, which provided baseline measurements of adhesion strength. The sintering conditions were shown to play an important role in the film-substrate adhesion strength, as well as the cohesion and ductility of the film itself. The methods and results described in this work support the establishment of process control steps that are necessary for quickly verifying the reliability of printed devices prior to their deployment in critical experiments.

Adhesion test↗
DOE OSTI2024

Critical Review of LPBF Metal Print Defects Detection: Roles of Selective Sensing Technology

The integrative potential of LPBF-printed parts for various innovative applications depends upon the robustness and infallibility of the part quality. Eliminating or sufficiently reducing factors contributing to the formation of defects is an integral step to achieving satisfiable part quality. Significant research efforts have been conducted to understand and quantify the triggers and origins of LPBF defects by investigating the material properties and process parameters for LPBF-printed geometries using various sensing technologies and techniques. Frequently, combinations of sensing techniques are applied to deepen the understanding of the investigated phenomena. The main objectives of this review are to cover the roles of selective sensing technologies by (1) providing a summary of LPBF metal print defects and their corresponding causes, (2) informing readers of the vast number and types of technologies and methodologies available to detect defects in LPBF-printed parts, and (3) equipping readers with publications geared towards defect detection using combinations of sensing technologies. Due to the large pool of developed sensing technology in the last few years for LPBF-printed parts that may be designed for targeting a specific defect in metal alloys, the article herein focuses on sensing technology that is common and applicable to most common defects and has been utilized in characterization for an extended period with proven efficiency and applicability to LPBF metal parts defect detection.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Screen printed Y and Bi-based superconductors

High T(sub c) superconducting thick film was prepared by screen printing process. Y-based (YBa2Cu3O(7 - x)) superconducting thick films were printed on 211/Al2O3, SNT/Al2O3, and YSZ substrates. Because of poor adhesion of the superconducting thick films to 211/Al2O3 and SNT/Al2O3 substrates, relatively low T(sub c) and J(sub c) values were obtained from the films printed on these substrates. Critical temperatures of YBa2Cu3O(7 - x) thick films deposited on 211/Al2O3 and SNT/Al2O3 substrates were about 80 K. The critical current densities of these films were less than 2 A/cm(exp 2). Higher T(sub c) and J(sub c) films were printed on the YSZ substrates; T(sub c) = 86.4 K and J(sub c) = 50.4 A/cm(exp 2). Multiple lead samples were also prepared on the YSZ substrates. These showed lower T(sub c) and J(sub c) values than plain samples. The heat treatment conditions of the multiple lead samples are still under investigation. Bi-based superconductor thick films have been obtained so far. Improving the superconducting properties of the BSCCO screen printed thick films will be emphasized in future work.

Haertling, Gene H.↗
NASA NTRS2013

Fully Printed, Flexible, Phased Array Antenna for Lunar Surface Communication

NASAs future exploration missions focus on the manned exploration of the Moon, Mars, and beyond, which will rely heavily on the development of a reliable communications infrastructure from planetary surface-to-surface, surface-to-orbit, and back to Earth. Flexible antennas are highly desired in many scenarios. Active phased array antennas (active PAAs) with distributed control and processing electronics at the surface of an antenna aperture offer numerous advantages for radar communications. Large-area active PAAs on flexible substrates are of particular interest in NASA s space radars due to their efficient inflatable package that can be rolled up during transportation and deployed in space. Such an inflatable package significantly reduces stowage volume and mass. Because of these performance and packaging advantages, large-area inflatable active PAAs are highly desired in NASA s surface-to-orbit and surface-to-relay communications. To address the issues of flexible electronics, a room-temperature printing process of active phased-array antennas on a flexible Kapton substrate was developed. Field effect transistors (FETs) based on carbon nanotubes (CNTs), with many unique physical properties, were successfully proved feasible for the PAA system. This innovation is a new type of fully inkjet-printable, two-dimensional, high-frequency PAA on a flexible substrate at room temperature. The designed electronic circuit components, such as the FET switches in the phase shifter, metal interconnection lines, microstrip transmission lines, etc., are all printed using a special inkjet printer. Using the developed technology, entire 1x4, 2x2, and 4x4 PAA systems were developed, packaged, and demonstrated at 5.3 GHz. Several key solutions are addressed in this work to solve the fabrication issues. The source/drain contact is developed using droplets of silver ink printed on the source/drain areas prior to applying CNT thin-film. The wet silver ink droplets allow the silver to wet the CNT thin-film area and enable good contact with the source and drain contact after annealing. A passivation layer to protect the device channel is developed by bonding a thin Kapton film on top of the device channel. This film is also used as the media for transferring the aligned CNT thin-film on the device substrate. A simple and cost-effective technique to form multilayer metal interconnections on flexible substrate is developed and demonstrated. Contact vias are formed on the second substrate prior to bonding on the first substrate. Inkjet printing is used to fill the silver ink into the via structure. The printed silver ink penetrates through the vias to contact with the contact pads on the bottom layer. It is then annealed to form a good connection. One-dimensional and two-dimensional PAAs were fabricated and characterized. In these circuits, multilayer metal interconnects were used to make a complete PAA system.

Subbaraman, Harish↗
NASA NTRS2013

BOK-Printed Electronics

The use of printed electronics technologies (PETs), 2D or 3D printing approaches either by conventional electronic fabrication or by rapid graphic printing of organic or nonorganic electronic devices on various small or large rigid or flexible substrates, is projected to grow exponentially in commercial industry. This has provided an opportunity to determine whether or not PETs could be applicable for low volume and high-reliability applications. This report presents a summary of literature surveyed and provides a body of knowledge (BOK) gathered on the current status of organic and printed electronics technologies. It reviews three key industry roadmaps- on this subject-OE-A, ITRS, and iNEMI-each with a different name identification for this emerging technology. This followed by a brief review of the status of the industry on standard development for this technology, including IEEE and IPC specifications. The report concludes with key technologies and applications and provides a technology hierarchy similar to those of conventional microelectronics for electronics packaging. Understanding key technology roadmaps, parameters, and applications is important when judicially selecting and narrowing the follow-up of new and emerging applicable technologies for evaluation, as well as the low risk insertion of organic, large area, and printed electronics.

Ghaffarian, Reza↗
NASA NTRS2014

Design of 3D-Printed Titanium Compliant Mechanisms

This paper describes 3D-printed titanium compliant mechanisms for aerospace applications. It is meant as a primer to help engineers design compliant, multi-axis, printed parts that exhibit high performance. Topics covered include brief introductions to both compliant mechanism design and 3D printing in titanium, material and geometry considerations for 3D printing, modeling techniques, and case studies of both successful and unsuccessful part geometries. Key findings include recommended flexure geometries, minimum thicknesses, and general design guidelines for compliant printed parts that may not be obvious to the first time designer.

Merriam, Ezekiel G.↗
DOE OSTI2025

Tunable 3D Aerosol Jet Printing of Low‐Power Redox‐Gated Transistors with Multicomponent Inks

Printed hybrid electronics (PHE) offer a promising alternative for microelectronics fabrication, addressing some limitations of traditional subtractive manufacturing. Despite the versatility of PHE, particularly in the customization of printing inks, these devices have not yet matched the performance of silicon-based electronics due to challenges in gating mechanisms and operational stability. However, the potential of low-voltage redox-gating to achieve significant carrier modulations in correlated metal oxides remains unexplored in PHE. This study systematically investigates vanadium dioxide (VO 2 ) nanoparticles and redox inks, linking their organization in solution to their morphology, phase state, and properties in solid films and multilayered structures. Using an aerosol jet printer (AJP), a solid-state VO 2 transistor is fabricated, operating at just 0.4 V gating voltage. The printed VO 2 films demonstrate redox-modulated conductivity and consistent transistor behavior. The solid-state redox gating materials also provide long-term stability, with the device maintaining performance over 6000 cycles without degradation. These results highlight the potential of redox gating to enhance the application of functional nanoparticles in printed hybrid microelectronics, especially for flexible, low-voltage, and energy-efficient devices.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Spatial‐Uniformity–Driven Bayesian Optimization for Rapid Development of Printed Perovskite Solar Cells

Printed metal halide perovskites can enable rapid, roll-to-roll manufacturing of a broad class of optoelectronics—flexible solar cells and imagers among them—while promising cost and speed advantages over incumbent silicon. However, though current methods offer high throughput and patterning capabilities, perovskite films’ spatial heterogeneity remains a challenge for large-area devices. Here, a spatial-uniformity-driven Bayesian optimization (BO) approach is leveraged to accelerate the development of printed perovskite solar cells and improve large-area device performance. Using a BO surrogate model, a 6D design space of ink chemistry and printing physics is explored via extensive iterative experimentation (≈100) informed by an objective function capturing spatial photoluminescence (PL) variance. It is discovered that optimizing for uniformity drives rapid advances in photovoltaic performance, yielding ≈20% power conversion efficiency (PCE) for small area (0.134 cm 2 ) devices and > 16% for large area (1 cm 2 ) devices. This machine-learning approach simultaneously enables rheological comparison of ink formulations that accelerate the leveling of Saffman-Taylor artifacts and improve film uniformity. Here, this showcases uniformity-driven BO as an efficient approach for uncovering the key printing physics and mitigating spatial heterogeneity to enable device scaling beyond small cell areas.

14 SOLAR ENERGY↗
DOE OSTI2026

Self-Leveling Inks for Printing Ultra-uniform Perovskite Solar Modules by Flexography

The report describes the development of scalable manufacturing methods for high-performance, stable perovskite solar modules using flexographic printing. The project developed self-leveling perovskite inks that exploit Marangoni flows to reduce coating defects and improve large-area film uniformity. Bayesian optimization was integrated with high-throughput photoluminescence mapping and photovoltaic measurements to efficiently optimize ink formulations and printing conditions. The resulting printed perovskite solar cells achieved champion power conversion efficiencies above 21.6%, with median efficiencies exceeding 20% across large device batches. At the module scale, printed devices achieved active-area efficiencies up to approximately 17.3% on 25 cm² substrates. The project also demonstrated improved performance and stability using additively patterned interconnections compared with laser-scribed controls. Overall, the work establishes a data-driven, roll-compatible pathway toward high-throughput, low-capital-cost manufacturing of uniform and stable perovskite photovoltaics.

14 SOLAR ENERGY↗
DOE OSTI2025

3D Printing of Cement-Based Materials Using Seawater for Simulated Marine Environments

Global demand for adaptable and rapidly deployable construction solutions in offshore, coastal, and fluvial environments continues to rise, driven by pressing needs to develop energy platforms, improve coastal resilience, and support emergency response in the face of natural disasters. Increased investment in human-made coastal infrastructure, such as piers, support structures for power lines, offshore wind farms, and seawall protection systems, further underscores this trend. This study investigates the development of printable concrete mixtures for underwater environments using seawater as a replacement for freshwater, using a 3D printing syringe-based extrusion system. The effect of seawater addition and the printing medium (in air vs. underwater) was assessed via rheological and mechanical performance characterization. The results indicate rheological properties are favorable for seawater adoption by producing mixtures with higher yield stress and viscosity with the same levels of admixtures used for freshwater. Seawater-based mixtures demonstrated superior dimensional stability compared to freshwater counterparts, maintaining cross-sectional geometry, while compressive strength results showed no statistical differences between in-air and underwater samples. However, flexural strength was significantly influenced by geometry and printing medium. These findings establish critical rheological parameters for printable underwater mixtures and highlight the need for optimized curing strategies and layer bonding techniques to improve interfacial strength in underwater 3D printing applications.

36 MATERIALS SCIENCE↗
NASA NTRS2015

3D Printing the Complete CubeSat

The 3D Printing the Complete CubeSat project is designed to advance the state-of-the-art in 3D printing for CubeSat applications. Printing in 3D has the potential to increase reliability, reduce design iteration time and provide greater design flexibility in the areas of radiation mitigation, communications, propulsion, and wiring, among others. This project is investigating the possibility of including propulsion systems into the design of printed CubeSat components. One such concept, an embedded micro pulsed plasma thruster (mPPT), could provide auxiliary reaction control propulsion for a spacecraft as a means to desaturate momentum wheels.

Printing CubeSat subsystems↗
NASA NTRS2018

Direct-Write Printing on Three-Dimensional Geometries for Miniaturized Detector and Electronic Assemblies

Direct-write printing techniques will enable new detector assemblies that were not previously possible with traditional assembly processes. Detector concepts were manufactured using this technology to validate repeatability. Additional detector applications and printed wires on a 3-dimensional magnetometer bobbin will be designed for print. This effort focuses on evaluating performance for direct-write manufacturing techniques on 3-dimensional surfaces. Direct-write manufacturing has the potential to reduce mass and volume for fabrication and assembly of advanced detector concepts by reducing trace widths down to 10 microns, printing on complex geometries, allowing new electronic concept production, and reduced production times of complex those electronics.

Direct-write printing↗
DOE OSTI2025

Print-and-Plate Architected Electrodes for Electrochemical Transformations Under Flow

Flow cell electrodes are typically composed of porous carbon materials, such as papers, felts, and cloths. However, their random architecture hinders the fundamental characterization of electrode structure-performance relationships during in situ operation of porous electrochemical flow systems. This work describes a “print-and-plate” method that combines direct ink writing of micro-periodic lattices with a two-step metal plating process that converts them into highly conductive (sheet resistance 40 mΩ sq -1 ) electrodes. Their operando performance is assessed in an anthraquinone disulfonic acid half-cell using widefield electrochemical fluorescence microscopy, where output current and fluorescence intensity are in excellent agreement. The pressure drop associated with flow through three electrode designs is determined via simulations from which the most efficient design is identified and manufactured via print-and-plate. Confocal fluorescence microscopy is then used to create a 3D map of the state of charge (SOC) inside this print-and-plate electrode. The experimental state of the charge map is in good agreement with computational predictions. The rapid design, simulation, and fabrication of print-and-plate electrodes enable fundamental investigations of how architected porosity affects electrochemical performance under flow.

3D-printing↗