Search NASA⌕ Search

SEARCH · Search NASA

Results for “process influence”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Influence of processing on secondary phase formation and microstructural evolution at U-10Mo alloy and Zr interlayer interfaces

Thermo-mechanical processing of uranium-10 wt. % molybdenum (U-10Mo) fuel plates leads to microstructure changes at the U-10Mo/Zr interfaces. Secondary phases formed at this interface are particularly important to interfacial bond strength, process optimization, and maintaining structural integrity of the U-10Mo fuel plates during irradiation. In this work, we determined the phases and phase transformation products occurring at the interface of the U-10Mo fuel and Zr interlayer when the fuel plate is subjected to short and long hot isostatic pressure times. Interfacial morphology, structure and composition of phases formed, and relative hardness across the U-10Mo/Zr interfaces were studied using a multi-length scale, multi-modal characterization approach involving electron microscopy, atom probe tomography, and atomic force microscopy. Here, results highlight that the extent of phase transformations, secondary phase formation, and hardness variability across interfaces can be controlled by modifying processing parameters. Phase diagram construction and thermodynamic calculations were performed using the Thermocalc software to identify expected phases formed at interfaces during the maximum hold temperature of 560 °C experienced during HIP.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of a new generation of quench and partitioning steels: Influence of processing parameters on texture, nanoindentation, and mechanical properties

A novel quenching and partitioning process (Q&P) including the hot stamping (HS) process was studied, using two stamping temperatures (750 °C and 800 °C) and two quenching temperatures (318 °C and 328 °C). This combination is here called Hot Stamping and Quenching and Partitioning process (HSQ&P). The partitioning step was performed at 400 °C for 100 s in all cycles. Microstructural features were comprehensively studied using electron backscattered diffraction and nanoindentation techniques. HSQ&P samples showed a good combination of ductility and high-strength due to the presence of: retained austenite, inter-critical ferrite with low stored internal strain energy, grain refinement via DIFT-effect (deformation induced ferrite transformation), martensite, and bainite. Significant internal stress relief was caused by carbon partitioning, which was induced by the DIFT-effect and the partitioning stage. This also led to a considerable stored energy, which was characterized by the Kernel average dislocation and geometrically necessary dislocation analysis. In addition, predominant {110}//strain direction crystallographic texture was identified, which promotes slip deformation and enhances the mechanical properties. Moreover, remarkable amounts of fine film-like retained austenite oriented along compact crystallographic directions (i.e., $\langle$111$\rangle$ and $\langle$112$\rangle$) were observed. Finally, subsize tensile test verified the optimum mechanical behavior of HSQ&P specimens.

36 MATERIALS SCIENCE↗

Direct Measure of Electrode Spatial Heterogeneity: Influence of Processing Conditions on Anode Architecture and Performance

The spatial (in)homogeneity of aqueous processed silicon electrodes using standard poly(acrylic acid)-based binders and slurry preparation conditions is demonstrated in this work. X-ray nanotomography shows segregation of materials into submicron-thick layers depending on the mixing method and starting binder molecular weights. Using a dispersant, or in situ production of dispersant from the cleavage of the binder into smaller molecular weight species, increases the resulting lateral homogeneity while drastically decreasing the vertical homogeneity as a result of sedimentation and separation due to gravitational forces. This data explains some of the variability in the literature with respect to silicon electrode performance and demonstrates two potential ways to improve slurry-based electrode fabrications.

36 MATERIALS SCIENCE↗

Characterization Of An EBL System: The Influence Of Process Parameters On Thickness Resist And Engraving Shapes

In LIGA process, the low flexibility due to the use of masks might be overcome using the electron beam of a scansion electron microscope (SEM) instead of the synchrotron radiation. In this way, through the vector control of the beam, it is possible to irradiate a specific path on the resist without using any mask. Anyway, it is important to remark that the Electron Beam Lithography (EBL) can not include all the applications of the X-ray LIGA technique but it could be a valid alternative only for some specific uses. In particular, some limits concerning the impression of high thickness resists are expected. An EBL system based on a SEM was recently implemented by the authors and some tests were carried out to characterize the device performances. Aim of this work is to asses the system performances in terms of maximum impressible thickness resist and shape of the engraved entities. Several tests were carried out by varying the resist thickness and the process parameters.

07 ISOTOPE AND RADIATION SOURCES↗

Influence of processing conditions on the morphology of expanded perlite/polypropylene composites

Perlite is an oversaturated, volcanic, glassy rock, which has chemically bound water from 2 to 5 wt%. Upon heating, perlite can be expanded up to 20 times of its original volume. Important applications are in the field of building industry, in refrigeration engineering or the pharmaceutical industry. As mineral filler in polymers, expanded perlite can increase the thermal conductivity, the viscosity and the mechanical properties of polypropylene composites. But there are still many challenges that must be analyzed to reach the full potential of those composites. This research work focuses on the morphology of expanded perlite/polypropylene (PP) compounds and the interactions between filler and polymer. To achieve good performance a homogenous dispersion of the filler in the polymer matrix is needed because the enhancement of the material correlates strongly with the morphology of the composite. Therefore it is necessary to characterize the microstructure of these materials in order to establish adequate structure-process-property relationships. The expanded perlite/PP composites were compounded with a co-rotating twin screw extruder Theysohn TSK 30/40D. For producing the closed cell expanded perlite a new technology, the bublon process, was used. For the material characterization two particles sizes were chosen and the filler content was varied at 5, 10 and 15 wt%. For the analysis of the effects of the screw geometry, two setups have been chosen for the processing of the materials. The produced materials were analyzed by scanning electron microscope (SEM) and tensile testing. The results show a reinforcement effect of the filler and differences in the inner structure of expanded perlite and in the morphology.

36 MATERIALS SCIENCE↗

Influence of processing parameters on long lasting hybrid phosphor for LED applications

Rare earth activated hybrid phosphors have made significant progress in terms of better light output, color properties and potential for long life. All these features coupled with low cost production and reduced maintenance have offered phosphor converted LEDs for diverse optoelectronic applications including signal lighting in advanced aviation. The present paper explores the effect of various processing parameters on luminescent hybrid phosphors fabricated through combustion synthesis.

36 MATERIALS SCIENCE↗

Influence of Process Parameters and Absorber Thickness on Efficiency of Polycrystalline CdSeTe/CdTe Thin Film Solar Cells

Graded absorbers devices with with CdSe 0.4 Te 0.6 (molar basis) and CdTe were fabricated. CdCl 2 treatment time, post-deposition CdCl 2 anneal time and thicknesses of CdSeTe and CdTe layers were varied. Photoluminescence and electrical measurements were performed on the fabricated devices. Results revealed that the individual thicknesses of CdSeTe and CdTe is critical to overall efficiency of the devices. Device fabricated on substrate with 0.5 μm CdSeTe, 3 μm CdTe with rest of process parameters kept unchanged, produced an efficiency of 20.14%. We report highest device efficiency among academia and research institutions.

Shimpi, Tushar↗

Influence of process parameters on rolling-contact-fatigue life of ion plated nickel-copper-silver lubrication

In this paper, we present a connection between argon ion flux, element-mixing, and rolling contact fatigue (RCF) life of a thin film nickel-copper-silver lubricant on ball bearings. The film is deposited on the balls using an ion plating process and tested for RCF in high vacuum. The ion flux is measured using a Langmuir probe and the plane stress within the film during deposition is calculated using a thin film model. Experiments reveal that there is an inverse relationship between ion flux and RCF life for most deposition voltage and pressure combinations tested, specifically, 15.5-18.5 mTorr and 1.5-3.5 kV. For voltages up to 2.5 kV, RCF life decreases as ion flux increases due to increased compressive stress within the film, reaching as high as 2.6 GPa. For voltages between 2.5 and 3.5 kV, interlayer mixing of nickel and copper with the silver layer reduces RCF life due to contamination, even as ion flux and corresponding film compressive stress are reduced. A Monte Carlo-based simulation tool, SRIM is used to track collision cascades of the argon ions and metal atoms within the coating layers. At process voltages above 2.5 kV we observe elemental mixing of copper and nickel with the silver layer using Auger electron spectroscopy of coated steel and Si{sub 3}N{sub 4} balls. The authors conclude that an ion flux greater than 5.0 x 10{sup 14} cm{sup -2} s{sup -1} leads to reduced RCF life due to high film stress. In addition, process voltages greater than 2.5 kV also reduce RCF life due to contamination and interlayer mixing of nickel and copper within the silver layer.

36 MATERIALS SCIENCE↗

Mitigating Transition Metal Dissolution from Mn-rich Cathodes: Influence of Processing and Testing Methods

Manganese-rich oxides continue to gain interest with respect to the development of Earth-abundant options for lithium-ion cathodes. Of the unique challenges that hinder the respective performance of various classes of such materials, manganese dissolution still stands as a common theme. The work herein explores Li 3 PO 4 as a robust surface protection layer on a prototypical, Co-free, manganese-rich cathode in the way of a lithium- and manganese-rich oxide. The study highlights the critical importance of synthesis and processing in realizing optimal performance of a given surface treatment by comparing sol-gel and atomic layer deposition methods. Furthermore, cycling protocols are emphasized as a critical factor in adequately gauging the efficacy of surface protection strategies to mitigate manganese dissolution and the subsequent electrochemical consequence. Optimized Li 3 PO 4 coatings coatings on lithium- and manganese-rich cathode particles are shown to greatly mitigate capacity fade, impedance rise, pore/void formation and mechanical damage during long-term cycling.

Mallick, Subhadip [Argonne National Laboratory (AN↗

Influence of Process Parameters and Alloy Composition on Crack Mitigation in Selective Laser Melting

Microcracking and residual stresses are key limitations of laser powder bed fusion (LPBF), an additive manufacturing (AM) technique that uses a high power laser to consolidate successive layers of metal powder. For tungsten, these microcracks find their origin in the combination of a ductile-to-brittle transition (DBT) between 200°C and 400°C and high residual stresses. This work utilized in situ high speed video to capture the cracking mechanisms, and combined the experimental results with thermomechanical modeling to unveil correlations between crack network morphology and process parameter-related variables, such as the local temperature and residual stress distributions. Consequently, preheating and alloying with rare earth oxides were adopted as possible crack mitigation strategies, the efficacy of which was tested against the initial fundamental baseline results. Preheating temperatures above 500°C eliminated all cracking, though this threshold is expected to be higher when tungsten powder (higher oxygen content) is introduced. Alloying can serve as an active oxygen getter in the system, but the rare earth oxides in this work were too large to have significant contributions to crack-mitigation.

36 MATERIALS SCIENCE↗

Synergistic interactions between an upper-level jet streak and diabatic processes that influence the development of a low-level jet and a secondary coastal cyclone

A series of numerical simulations of the February 1979 Presidents Day cyclone is presented. The development of the low-level jet (LLJ) associated with the cyclone is described, and the mesoscale numerical model, initial analyses, and experimental design used in the study are discussed. Four numerical simulations are discussed and compared, including an adiabatic simulation that isolates the development of upper-level divergence along the axis of a subtropical jet streak and three other simulations that reveal the contributions of sensible and latent heat release in modifying lower-tropospheric wind fields and reducing the sea-level pressure. The formation of the LLJ is described through an evaluation of trajectories derived from the various model simulations. The effect of the LLJ on secondary cyclogenesis along the East Coast is described.

Uccellini, Louis W.↗

The influence of processing parameters on microstructural development of low-weight-percent primary, pro-eutectic, dendritic alloys during directional solidification

Alloy compositions centering about Sn- 5 to 15 wt pct Al and Pb- 4 to 20 wt pct Cu have been directionally solidified as a function of growth rate and orientation with respect to earth's gravity vector. The effect of these processing variables on macrosegregation is presented, and the consequence of a structural transition from primary columnar to equiaxed dendritic growth is examined. Effects detrimental to microstructure and attributed to density variations are shown to be minimized by a novel processing technique. In view of the ground-based results, some considerations follow regarding what might be gained by solidifying these alloys in a microgravity environment.

Grugel, R. N.↗

Influence of Processing on the Microstructure and Mechanical Properties of a NbAl3-Base Alloy

Induction melting and rapid solidification processing, followed by grinding to 75-micron powder and P/M consolidation, have been used to produce a multiphase, NbAl3-based, oxidation-resistant alloy of Nb-67Al-7Cr-0.5Y-0.25W composition whose strength and ductility are significantly higher than those of the induction-melted alloy at test temperatures of up to 1200 K. Attention is given to the beneficial role of microstructural refinement; the major second phase, AlNbCr, improves both oxidation resistance and mechanical properties.

Hebsur, Mohan G.↗

Influence of Processing Parameters on the Mechanical Properties of 3D Printed Borosilicate Particulate Reinforced Polymer Composites

Emerging composite materials are expanding the potential of additive manufacturing and enabling applications previously restricted by traditional manufacturing methods. The multi-phase nature of these composite materials combined with the complex in-ternal geometry of additively manufactured parts have enabled unique behavior, and potentially new applications. Additionally, these materials can be pyrolyzed to create dense metal, ceramic, and glass parts with geometries typically not achievable by tra-ditional processes. Additive manufacturing of borosilicate glass-based systems can open new applications in nuclear engineering, astronomy, and bone regrowth therapy. To elucidate the process-parameter relationship of borosilicate-polylactic acid (PLA) composites, mechanical testing was conducted and compared with a pure polylactic acid polymer baseline. Test specimens were fabricated by fused-filament fabrication with minimal post-processing. Yield strength, ultimate strength, and elastic modulus were calculated from stress-strain curves. Optical and scanning electron microscopy were conducted to observe the specimen microstructure before and after testing. The highest compressive yield strength for the composite was 28.22 MPa, and the highest compressive yield strength for PLA was 49.30 MPa. Print orientation was found to benefit the composite material but have a detrimental effect on the pure matrix material. An elastic modulus of 2.66 GPa was recorded for the borosilicate-PLA composite at 100% infill, 1 shell wall, and layer lines parallel to compression axis. Microscopy revealed that lower modulus composite specimens had the particulates re-distributed within the matrix. Tensile testing was done according to a polymer testing standard, which caused difficulties obtaining consistent fracture within the gauge length.

mechanical testing↗