Search NASA⌕ Search

SEARCH · Search NASA

Results for “pull out force”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

An analysis of the wear behavior of SiC whisker-reinforced alumina from 25 to 1200 C

A model is described for predicting the wear behavior of whisker reinforced ceramics. The model was successfully applied to a silicon carbide whisker reinforced alumina ceramic composite subjected to sliding contact. The model compares the friction forces on the whiskers due to sliding, which act to pull or push them out of the matrix, to the clamping or compressive forces on the whiskers due to the matrix, which act to hold the whiskers in the composite. At low temperatures, the whiskers are held strongly in the matrix and are fractured into pieces during the wear process along with the matrix. At elevated temperatures differential thermal expansion between the whiskers and matrix can cause loosening of the whiskers and lead to pullout during the wear process and to higher wear. The model, which represents the combination of elastic stress analysis and a friction heating analysis, predicts a transition temperature at which the strength of the whiskers equals the clamping force holding them in the matrix. Above the transition the whiskers are pulled out of the matrix during sliding, and below the transition the whiskers are simply fractured. The existence of the transition gives rise to a dual wear mode or mechanism behavior for this material which was observed in laboratory experiments. The results from this model correlate well with experimentally observed behavior indicating that the model may be useful in obtaining a better understanding of material behavior and in making material improvements.

Dellacorte, Christopher↗
NASA NTRS1978

Comments on the drag-free control of a solar probe relativity mission

A spacecraft going within 4 solar radii of the Sun experiences an acceleration up to .00005 g from solar radiation pressure, and significant (though smaller) accelerations from the solar wind. To obtain satisfactory information about relativistic effects and the Sun's quadrupole mass coefficient, these non-gravitational accelerations are either measured or compensated out by making the spacecraft drag free. A proof mass inside the spacecraft structure is shielded from the external forces, so that it follows a nearly ideal gravitational orbit, and a control system activates gas jets (or other translational forcers) to make the vehicle follow the mass. The problems are mechanizing the control laws and minimizing extraneous effects such as the self gravitational pull of the spacecraft. The extraneous forces can be averaged in one plane by having a spinning vehicle.

Everitt, C. W. F.↗
NASA NTRS1992

Multibody interference at transonic Mach numbers

An experimental and computational study has been made of the forces and moments on multibody configurations at Mach numbers from 0.6 to 1.2. The interference forces and moments that occur on symmetric double and triple body configurations at zero angle of attack are examined in detail. In all cases, the normal interference force is always in a direction to pull the bodies together and the moment about the 0.5L point is always to rotate the tips of the bodies away from the center of the configuration. The axial interference force (pressure drag at zero angle of attack) increases the drag per store as additional stores are added to the configuration. The effect of angle of attack on the interference is relatively small.

Chapman, Gary T.↗
NASA NTRS2003

Loading Configurations and Ground Reaction Forces During Treadmill Running in Weightlessness

Studies have shown losses in bone mineral density of 1-2% per month in critical weight bearing areas such as the proximal femur during long-term space flight (Grigoriev, 1998). The astronauts currently onboard the International Space Station (ISS) use a treadmill as an exercise countermeasure to bone loss that occurs as a result of prolonged exposure to weightlessness. A crewmember exercising on the treadmill is attached by a harness and loading device. Ground reaction forces are obtained through the loading device that pulls the crewn1ember towards the treadmill surface during locomotion. McCrory et al. (2002) found that the magnitude of the peak ground reaction force (pGRF) during horizontal suspension running, or simulated weightlessness, was directly related to the load applied to the subject. It is thought that strain magnitude and strain rate affects osteogenesis, and is a function of the magnitude and rate of change of the ground reaction force. While it is not known if a minimum stimulus exists for osteogenesis, it has been hypothesized that in order to replicate the bone formation occurring in normal gravity (1 G), the exercise in weightlessness should mimic the forces that occur on earth. Specifically, the pGRF obtained in weightlessness should be comparable to that achieved in 1 G.

DeWitt, John↗
NASA NTRS1991

Hand Broaching Tool For Use In Confined Areas

Broaching tool cuts keyslots in tapped holes. With exceptionally slim outer body, well suited for work in areas of limited accessibility, particularly when features of workpiece create obstructions. Threaded sections on inner and outer bodies mate. After inner body used to broach keyways in hole in workpiece, turning outer body by its handle forces bearing surface against workpiece and pulls inner body tip out of hole. Reduces time for broaching holes from 4 h to 1 h. Blade replaced only twice per circle.

Beach, Arthur A.↗
NASA NTRS1983

Alignment-enhancing feed-through conductors for stackable silicon-on-sapphire wafers

Alignment-enhancing electrically conductive feed-through paths are provided for the high-speed low-loss transfer of electrical signals between integrated circuits of a plurality of silicon-on-sapphire bodies arrayed in a stack. The alignment-enhancing feed-throughs are made by a process involving the drilling of holes through the body, double-sided sputtering, electroplating, and the filling of the holes with solder by capillary action. The alignment-enhancing feed-throughs are activated by forming a stack of wafers and remelting the solder whereupon the wafers, and the feed-through paths, are pulled into alignment by surface tension forces.

Anthony, Thomas R.↗
NASA NTRS1985

Method for making alignment-enhancing feed-through conductors for stackable silicon-on-sapphire

Alignment-enhancing electrically conductive feed-through paths are provided for the high-speed low-loss transfer of electrical signals between integrated circuits of a plurality of silicon-on-sapphire bodies arrayed in a stack. The alignment-enhancing feed-throughs are made by a process of this invention involving the drilling of holes through the body, double-sided sputtering, electroplating, and the filling of the holes with solder by capillary action. The alignment-enhancing feed-throughs are activated by forming a stack of wafers and remelting the solder whereupon the wafers, and the feed-through paths, are pulled into alignment by surface tension forces.

Anthony, Thomas R.↗
NASA NTRS2017

Compactor for Space Toilet

A toilet for use on a space vehicle has a toilet bowl having a storage canister at a remote end for receiving human waste. The compactor includes a cable connected to a lever which pulls the cable in a direction forcing the compactor into the storage canister to compact the captured waste when the lever is actuated.

Autrey, David↗
NASA NTRS1993

Loads produced by a suited subject performing tool tasks without the use of foot restraints

With an increase in the frequency of extravehicular activities (EVA's) aboard the Space Shuttle, NASA is interested in determining the capabilities of suited astronauts while performing manual tasks during an EVA, in particular the situations in which portable foot restraints are not used to stabilize the astronauts. Efforts were made to document the forces that are transmitted to spacecraft while pushing and pulling an object as well as while operating a standard wrench and an automatic power tool. The six subjects studied aboard the KC-135 reduced gravity aircraft were asked to exert a maximum torque and to maintain a constant level of torque with a wrench, to push and pull an EVA handrail, and to operate a Hubble Space Telescope (HST) power tool. The results give an estimate of the forces and moments that an operator will transmit to the handrail as well as to the supporting structure. In general, it was more effective to use the tool inwardly toward the body rather than away from the body. There were no differences in terms of strength capabilities between right and left hands. The power tool was difficult to use. It is suggested that ergonomic redesigning of the power tool may increase the efficiency of power tool use.

Rajulu, Sudhakar L.↗
NASA NTRS2004

A MEMS Micro-Translation Stage with Long Linear Translation

A MEMS Micro-Translation Stage (MTS) actuator concept has been developed that is capable of traveling long distances, while maintaining low power, low voltage, and accuracy as required by many applications, including optical coupling. The Micro-Translation Stage (MTS) uses capacitive electrostatic forces in a linear motor application, with stationary stators arranged linearly on both sides of a channel, and matching rotors on a moveable shuttle. This creates a force that allows the shuttle to be pulled along the channel. It is designed to carry 100 micron-sized elements on the top surface, and can travel back and forth in the channel, either in a stepping fashion allowing many interim stops, or it can maintain constant adjustable speeds for a controlled scanning motion. The MTS travel range is limited only by the size of the fabrication wafer. Analytical modeling and simulations were performed based on the fabrication process, to assure the stresses, friction and electrostatic forces were acceptable to allow successful operation of this device. The translation forces were analyzed to be near 0.5 micron N, with a 300 micron N stop-to-stop time of 11.8 ms.

Ferguson, Cynthia K.↗
NASA NTRS1984

Silicon Foils Growth by Interface-controlled Crystallization

During interface controlled crystallization (ICC) the chance to accelerate the removal of crystallization heat is the basis for high pulling rates of about 100 mm/min. The forced heat flow from the extended crystallization front to a cooling ramp is controlled by a lubricating melt film which also influences the crystallization behavior by suppressing nucleation centers. The basic principles of this full casting technique are presented and the influences of process parameters on the morphology of prepared silicon foils are demonstrated. Three different types of crystalline structure were found in silicon foils grown to ICC technique: dendritic, coarse granular and monocrystalline with (111) 211 orientation. The criteria for their appearance of process variables are discussed.

Helmreich, D.↗
NASA NTRS1985

Coal-Sizing Auger

Aft end of auger, like forward, face-piercing end, equipped with hard cutting bits such as diamonds. As auger breaks face, pulls broken coal lumps into jaws and forces them into hardened throat section. There, cutting bits chew up lumps: Clearance between throat and auger shaft sets maximum size for coal particles that pass through. Auger motion pushes coal particles into mixing chamber, where paddles combine them with water.

Lewis, E. V.↗
NASA NTRS2015

0.625" FPPW Abstract

Friction Pull Plug Welding (FPPW) is a solid‐state process that is the primary close out method for Self‐ Reacting Friction Stir Welding (SR‐FSW). This process uses a servo hydraulic machine to spin an aluminum plug to several thousand revolutions per minute and pull the plug with several thousand pound force into an aluminum piece of material. This process, which has been around for approximately a decade, has proven to be a very difficult process to develop. There are large number of variables with interactions and correlations that are difficult to detect. Historically this method only provided good results on aluminum material up to 0.327" thick. The SLS rocket required weld land configurations of up to 0.625" thick. This not only pushed the limits of the process but also of the tools procured for materials 1/2 as thick. Ultimate Tensile Results was typically the response used for FPPW input variables. The problem was there were multiple processes including, welding, post weld machining, Non Destructive Evaluation, specimen fabrication and mechanical testing between the FPPW inputs and the mechanical test results. This only compiled the list of variables and made the process of FPPW even more difficult to develop. This presentation and paper describes the new process development methodology, which uses the FPPW tool's feedback to observe the process and develop it systematically. It captures 6 months and 600 plugs worth of work using only the tool's feedback as a response to the process. This presentation describes the solution to the issue, a solution whose methodology could apply to a variety of other processes.

Littell, Justin↗
NASA NTRS1983

Inversion for the driving forces of plate tectonics

Inverse modeling techniques have been applied to the problem of determining the roles of various forces that may drive and resist plate tectonic motions. Separate linear inverse problems have been solved to find the best fitting pole of rotation for finite element grid point velocities and to find the best combination of force models to fit the observed relative plate velocities for the earth's twelve major plates using the generalized inverse operator. Variance-covariance data on plate motion have also been included. Results emphasize the relative importance of ridge push forces in the driving mechanism. Convergent margin forces are smaller by at least a factor of two, and perhaps by as much as a factor of twenty. Slab pull, apparently, is poorly transmitted to the surface plate as a driving force. Drag forces at the base of the plate are smaller than ridge push forces, although the sign of the force remains in question.

Richardson, R. M.↗
NASA NTRS2003

Optical Tweezers Array and Nimble Tweezers Probe Generated by Spatial- Light Modulator

An optical tweezers is being developed at the NASA Glenn Research Center as a visiblelight interface between ubiquitous laser technologies and the interrogation, visualization, manufacture, control, and energization of nanostructures such as silicon carbide (SiC) nanotubes. The tweezers uses one or more focused laser beams to hold micrometer-sized particles called tools (sometimes called tips in atomic-force-microscope terminology). A strongly focused laser beam has an associated light-pressure gradient that is strong enough to pull small particles to the focus, in spite of the oppositely directed scattering force; "optical tweezers" is the common term for this effect. The objective is to use the tools to create carefully shaped secondary traps to hold and assemble nanostructures that may contain from tens to hundreds of atoms. The interaction between a tool and the nanostructures is to be monitored optically as is done with scanning probe microscopes. One of the initial efforts has been to create, shape, and control multiple tweezers beams. To this end, a programmable spatial-light modulator (SLM) has been used to modify the phase of a laser beam at up to 480 by 480 points. One program creates multiple, independently controllable tweezer beams whose shapes can be tailored by making the SLM an adaptive mirror in an interferometer (ref. 1). The beams leave the SLM at different angles, and an optical Fourier transform maps these beams to different positions in the focal plane of a microscope objective. The following figure shows two arrays of multiple beams created in this manner. The patterns displayed above the beam array control the intensity-to-phase transformation required in programming the SLM. Three of the seven beams displayed can be used as independently controllable beams.

Decker, Arthur J.↗
NASA NTRS1964

Self sealing disconnect for tubing forms metal seal after breakaway

Disconnect fittings form a positive metal seal when the fill tube pulls against a metal sleeve when disconnected by force. A specially designed sleeve surrounds the fill tube. O-rings in the shoulder of the sleeve and near the outer end of the fill tube seal against leakage.

Gernandt, H. H.↗
NASA NTRS1984

Adhesion between polymers and evaporated gold and nickel films

To obtain information on the adhesion between metal films and polymeric solids, the adhesion force was measured by means of a tensile pull test. It was found that the adhesion strengths between polymeric solids and gold films evaporated on polymer substrates were (1.11 + or - 0.53) multiplied by 10(6) N/M(2) on PTFE, about 5.49 multiplied by 10(6) N/m(2) on UHMWPE, and 6.54x10(6) on 6/6 nylon. The adhesion strengths for nickel films evaporated on PTFE, UHMWPE, and 6/6 nylon were found to be a factor of 1.7 higher than those for the gold coated PTFE, UHMWPE, and 6/6 nylon. To confirm quantitatively the effect of electron irradiation on the adhesion strength between a PTFE solid and metal films, a tensile pull test was performed on the irradiated PTFE specimens, which were prepared by evaporating nickel or gold on PTFE surfaces irradiated by 2-keV electrons for various times. After irradiation, the adhesion strength increased to (4.92 + or - 0.92)x10(6) N/m(2) for nickel coated PTFE and (1.82 + or - 0.48)x10(6) N/m(2) for gold coated PTFE. The improvement in adhesion for nickel is higher than that for gold.

Yamada, Y.↗
NASA NTRS1996

A Comparison of the Physiology and Mechanics of Exercise in LBNP and Upright Gait

Bone, muscular strength, aerobic capacity, and normal fluid pressure gradients within the body are lost during bed rest and spaceflight. Lower Body Negative Pressure (LBNP) exercise may create musculoskeletal and cardiovascular strains equal to a greater than those experienced on Earth and elucidate some of the mechanisms for maintaining bone integrity. LBNP exercise simulates gravity during supine posture by using negative pressure to pull subjects inward against a treadmill generating footward forces and increasing transmural pressures. Footward forces are generated which equal the product of the pressure differential and the cross-sectional area of the LBNP waist seal. Subjects lie supine within the chamber with their legs suspended from one another via cuffs, bungee cords, and pulleys, such that each leg acts as a counterweight to the other leg during the gait cycle. The subjects then walk or run on a treadmill which is positioned vertically within the chamber. Supine orientation allows only footward force production due to the negative pressure within the chamber. The purpose of this study was to determine if the kinematics, kinetics, and metabolic rate during supine walking and slow running on a vertical treadmill within LBNP are similar to those on a treadmill in 1-g environment in an upright posture.

Boda, W. L.↗