Search NASA⌕ Search

SEARCH · Search NASA

Results for “raceways”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Effects of Media Nutrient Variation on Microalgae Productivity and Economics During Semi-Continuous Cultivation

The development of large-scale microalgae growth for biofuel production is currently limited by the cost of biomass production. However, new approaches to infrastructure and cultivation practices are bringing the field closer to realization. Macronutrients in the cultivation media contribute significant costs, especially since their concentrations have not been optimized for specific strains and conditions. Environmental photobioreactors (ePBRs) were used to simulate cultivation under outdoor conditions, during which the nitrogen and phosphorus levels in the media were varied. The growth of two potential biofuel production strains, Picochlorum celeri and Tetraselmis striata, with varying nutrient inputs during summer and winter scripts, respectively, was studied. This study demonstrated that nitrogen and phosphorus in f/2 media could be reduced by more than 60% from the standard formulation, while maintaining growth rates in a semi-continuous harvesting approach. Experiments comparing the standard and reduced nutrient input concentrations were also conducted for both species in 820 L outdoor raceway ponds, in Mesa, AZ. P. celeri grown in these ponds in October had a growth rate of 10.6 ± 0.7 g/m 2 /day and 10.6 ± 0.3 g/m 2 /day for the standard and low-nutrient P. celeri ponds, respectively. T. striata grown in April–May had a growth rate of 16.6 ± 1.4 g/m 2 /day for the standard nutrient input ponds and 17.4 ± 1.1 g/m 2 /day for the low-nutrient input ponds, and in October 14.5 ± 0.6 g/m 2 /day for standard nutrient ponds and 14.4 ± 0.6 g/m 2 /day for low-nutrient ponds. These outdoor data therefore confirmed the indoor ePBR data. Techno-economic analysis shows that, if high growth rates can be attained at lower nutrient concentrations, a reduction of at least 60% in nutrient costs can be achieved. Such results highlight the importance of managing macronutrient media inputs, as these have a considerable contribution to biomass production costs in large-scale facilities. The analysis also points to the importance of maintaining high spent medium recycling rates in an industrial deployment, so as to minimize the losses of nitrogen and phosphorus compounds.

09 BIOMASS FUELS↗
NASA NTRS1967

Tester for study of rolling element bearings

Five-ball fatigue tester makes possible the study of rolling element phenomena. The device consists of a driven test ball pyramided upon four lower balls positioned by a separator and free to rotate in an angular contact raceway.

Zaretsky, E. V.↗
NASA NTRS1967

Design concept to decrease relative speed of ball bearings

Intermediate ring decreases the rolling speed of a ball bearing relative to the rotational speed of the shaft. It has raceways on its inner and outer peripheries and an additional row of balls. The modification permits operation at much higher shaft speeds than usual.

Jesman, S.↗
NASA NTRS1972

Analysis of an arched outer-race ball bearing considering centrifugal forces

A Newton-Raphson method of iteration was used in evaluating the radial and axial projection of the distance between the ball center and the outer raceway groove curvature center (V and W). Fatigue life evaluations were made. The similar analysis of a conventional bearing can be directly obtained from the arched bearing analysis by simply letting the amount of arching be zero (g = 0) and not considering equations related to the unloaded half of the outer race. The analysis was applied to a 150-mm angular contact ball bearing. Results for life, contact loads, and angles are shown for a conventional bearing (g = 0) and two arched bearings (g = 0.127 mm (0.005 in.), and 0.254 mm (0.010 in.)). The results indicate that an arched bearing is highly desirable for high speed applications. In particular, for a DN value of 3 million (20,000 rpm) and an applied axial load of 4448 N (1000 lb), an arched bearing shows an improvement in life of 306 percent over that of a conventional bearing. At 4.2 million DN (28,000 rpm), the corresponding improvement is 340 percent. It was also found for low speeds, the arched bearing does not offer the advantages that it does for high speed applications.

Hamrock, B. J.↗
NASA NTRS1972

Analysis of an arched outer-race ball bearing considering centrifugal forces.

Thrust-load analysis of a 150-mm angular contact ball bearing, taking into account centrifugal forces but omitting gyroscopics, elastohydrodynamics, and thermal effects. A Newton-Raphson method of iteration is used to evaluate the radial and axial projection of the distance between the ball center and the outer raceway groove curvature center. Fatigue life of the bearing is evaluated. Results for life, contact loads, and angles are given for a conventional bearing and two arched bearings.

Hamrock, B. J.↗
NASA NTRS1977

Restoration of bearings

Process consisting of grinding raceways to oversize but original quality condition and installing new oversize balls or bearings restores wornout ball and roller bearings to original quality, thereby doubling their operating life. Evaluations reveal process results in restoration of 90% of replaced bearings at less than 50% of new-bearing costs.

Parker, R. J.↗
NASA NTRS1977

Elastic distortion of flanged inner ring of high-speed cylindrical roller bearing

The elastic distortion of the inner ring of an experimental roller bearing is investigated analytically. The geometry of the experimental bearing is unusually complex, and for this reason a bearing with an axially symmetric inner ring is also analyzed. Only the inner ring and shaft are considered using a two dimensional finite element program that can accommodate interference between these components. The results suggest that the elastic distortions are modest in relation to the design clearances associated with the experimental bearing. The variation of the radial deflection of the raceway may, however, be significant in some circumstances.

Taylor, C. M.↗
NASA NTRS1978

The elastic distortion of the flanged inner ring of a high-speed cylindrical roller bearing

The elastic distortion of the inner ring of an experimental 3,000,000 DN roller bearing is investigated analytically. The geometry of this bearing is unusually complex and for this reason a bearing with an axially symmetric inner ring and shaft is also analyzed. Only the inner ring and shaft are considered using a two-dimensional finite element computer program which enables interference between these components to be accommodated. The results for the experimental bearing suggest that elastic distortions are modest in relation to the design clearances. However, the variation of the radial deflection of the raceway may be significant for some circumstances and the interference fit adopted between the ring and shaft appears to be questionably low.

Taylor, C. M.↗
NASA NTRS1978

High speed cylindrical roller bearing analysis, SKF computer program CYBEAN. Volume 2: User's manual

The CYBEAN (Cylindrical Bearing Analysis) was created to detail radially loaded, aligned and misaligned cylindrical roller bearing performance under a variety of operating conditions. Emphasis was placed on detailing the effects of high speed, preload and system thermal coupling. Roller tilt, skew, radial, circumferential and axial displacement as well as flange contact were considered. Variable housing and flexible out-of-round outer ring geometries, and both steady state and time transient temperature calculations were enabled. The complete range of elastohydrodynamic contact considerations, employing full and partial film conditions were treated in the computation of raceway and flange contacts. Input and output architectures containing guidelines for use and a sample execution are detailed.

Kleckner, R. J.↗
NASA NTRS1982

Bearing fatigue investigation 3

The operating characteristics of large diameter rolling-element bearings in the ultra high speed regimes expected in advanced turbine engines for high performance aircraft were investigated. A high temperature lubricant, DuPont Krytox 143 AC, was evaluated at bearing speeds to 3 million DN. Compared to the results of earlier, similar tests using a MIL-L-23699 (Type II) lubricant, bearings lubricated with the high density Krytox fluid showed significantly higher power requirements. Additionally, short bearing lives were observed when this fluid was used with AISI M50 bearings in an air atmosphere. The primary mode of failure was corrosion initiated surface distress (fatigue) on the raceways. The potential of a case-carburized bearing to sustain a combination of high-tangential and hertzian stresses without experiencing race fracture was also investigated. Limited full scale bearing tests of a 120 mm bore ball bearing at a speed of 25,000 rpm (3 million DN) indicated that a carburized material could sustain spalling fatigue without subsequent propagation to fracture. Planned life tests of the carburized material had to be aborted, however, because of apparent processing-induced material defects.

Nahm, A. H.↗
NASA NTRS1983

Corrosion of simulated bearing components of three bearing steels in the presence of chloride-contaminated lubricant

Corrosion tests were run with AISI 52100, AISI M-50 and AMS 5794 under conditions that simulate the crevice corrosion found in aircraft ball and roller bearings rejected at overhaul for corrosion. Test specimens were fabricated that simulated the contacts of balls or rollers and the raceways. Corrosion cells were assembled in the presence of a lubricant contaminated with water and chloride ions. The cell was then thermally cycled between 339 K (150 F) and 276 K (37 F). The corrosion observed after 14 cycles was that of crevice and pitting corrosion typically found in aircraft bearings. AMS 5749 showed a very slight amount of corrosion. No appreciable differences were noted between AISI 52100 and AISI M-50, but both showed much greater corrosion than AMS 5749. The corrosion pits observed in AISI M-50 appeared to be fewer in number but generally deeper and larger than in AISI 52100.

Parker, R. J.↗
NASA NTRS1983

Effect of carbide distribution on rolling-element fatigue life of AMS 5749

Endurance tests with ball bearings made of corrosion resistant bearing steel which resulted in fatigue lives much lower than were predicted are discussed. Metallurgical analysis revealed an undesirable carbide distribution in the races. It was shown in accelerated fatigue tests in the RC rig that large, banded carbides can reduce rolling element fatigue life by a factor of approximately four. The early spalling failures on the bearing raceways are attributed to the large carbide size and banded distribution.

Parker, R. J.↗
NASA NTRS1985

Effect of two inner-ring oil-flow distribution schemes on the operating characteristics of a 35 millimeter bore ball bearing to 2.5 million DN

Parametric tests were conducted with a 35-mm-bore, split-inner-ring ball bearing with a double-inner-land-guided cage. Provisions were made for through-the-inner-ring lubrication. Test condictions were either a thrust load of 667 N (150 lb) or a combined load of 667 N (150 lb) thrust and 222 N (50 lb) radial, shaft speeds from 32000 to 72000 rpm, and an oil-inlet temperature of 394 K (250 deg F). Outer ring cooling was used in some tests. Tests were run with either 50 or 75 percent of the total oil flow distributed to the inner-ring raceway. Successful operation was experienced with both 50% and 75% flow patterns to 2.5 million DN. Cooling the outer ring had little effect on inner-ring temperature; however, the outer-ring temperature decreased as much as 7% at 2.5 million DN. Maximum recorded power loss was 3.1 kW (4.2 hp), and maximum cage slip was 8.7 percent. Both occurred at a shaft speed of 72000 rpm, a lubricant flow rate of 1900 cu/min (0.50 gal/min), a combined load, and no outer-ring cooling.

Schuller, F. T.↗
NASA NTRS1984

Fast numerical calculations of EHD sliding traction forces Application to rolling bearings

Based on analytical calculations assuming isothermal elastohydrodynamic (EHD) lubrication conditions, and on curve-fitting of a thermal correction factor, a new formula is proposed to calculate the sliding traction force developed in a concentrated contact, assuming a nonlinear, viscoelastic lubricant and undirectional sliding. When sliding occurs in the rolling and transverse directions (bidimensional sliding), a simplified numerical method is outlined by which the components of the local shear stress are quickly calculated. The latter method is applied to the calculation of the shear stress and temperature distribution in the ball-raceway contacts of an angular-contact ball bearing. Because of the viscoelastic behavior of the lubricant, a nonzero lateral traction force is obtained.

Houpert, L.↗
NASA NTRS1986

Analysis of mixed-mode crack propagation using the boundary integral method

Crack propagation in a rotating inner raceway of a high speed roller bearing is analyzed using the boundary integral equation method. The method consists of an edge crack in a plate under tension, upon which varying Hertzian stress fields are superimposed. A computer program for the boundary integral equation method was written using quadratic elements to determine the stress and displacement fields for discrete roller positions. Mode I and Mode II stress intensity factors and crack extension forces G sub 00 (energy release rate due to tensile opening mode) and G sub r0 (energy release rate due to shear displacement mode) were computed. These calculations permit determination of that crack growth angle for which the change in the crack extension forces is maximum. The crack driving force was found to be the alternating mixed-mode loading that occurs with each passage of the most heavily loaded roller. The crack is predicted to propagate in a step-like fashion alternating between radial and inclined segments, and this pattern was observed experimentally. The maximum changes DeltaG sub 00 and DeltaG sub r0 of the crack extension forces are found to be good measures of the crack propagation rate and direction.

Mendelson, A.↗
NASA NTRS1985

Solar maximum mission post flight performance analyses of standard reaction wheels S/N's 102, 103, 104 and 105

On 24 January 1985, the four Solar Maximum Mission Reaction Wheels, S/N 102 through 105 were returned to Sperry for postflight analysis. The analysis consisted of visual examination; preliminary electrical checks; performance testing at ambient, hot, and cold temperature environments; and internal pressure measurements. Based on the performance test results and past utilization in space, one reaction wheel was selected for teardown to study lubricant distribution, bearing and reservoir lube loss, bearing raceway condition, and visual examination of conformal coating, soldering, and other internal features.

Source record↗
NASA NTRS1986

Lubricant effects on bearing life

Lubricant considerations for rolling-element bearings have within the last two decades taken on added importance in the design and operation of mechanical systems. The phenomenon which limits the useful life of bearings is rolling-element or surface pitting fatigue. The elastohydrodynamic (EHD) film thickness which separates the ball or roller surface from those of the raceways of the bearing directly affects bearing life. Chemical additives added to the lubricant can also significantly affect bearings life and reliability. The interaction of these physical and chemical effects is important to the design engineer and user of these systems. Design methods and lubricant selection for rolling-element bearings are presented and discussed.

Zaretsky, Erwin V.↗