Search NASA⌕ Search

SEARCH · Search NASA

Results for “selective laser melting (SLM)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

81 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

HEAT TRANSFER ASPECTS OF TWO PISTON SPLAT QUENCHING

This thesis investigates the heat transfer aspects of the two-piston splat quench system by modifying surface roughness and by using copper and stainless steel platens. In additive manufacturing, specifically selective laser melting (SLM), metal is subjected to a very rapid heating and cooling that produces cooling rates in the range from 105-106 °C/s. This rapid solidification produces microstructures that deviate far from equilibrium. Splat quenching is an experimental method that produces rapidly solidified structures under cooling rates that are comparable to those found in additive manufacturing. The splat quenching approach allows for more efficient testing of the rapid solidification behavior of a wide variety of alloys. In this thesis, two platen characteristics, surface roughness and material thermal conductivity, were examined to determine their role in controlling the heat transfer and the subsequent cooling rate during splat quenching of austenitic stainless steel 316L. To that objective, 5 surface finishes were produced using metallographic techniques, from 7046-203 Å Rms. Copper and 316L stainless steel platen material were used to reach different levels of thermal conductance. The combination of these 2 variables created 10 scenarios, which were examined using, backscatter imaging, secondary imaging, and electron back scatter diffraction. Cooling rates were estimated using cell sizing obtained through electrolytic etching and secondary imaging. This thesis determined that both surface modification and changes in material type had a statistically significant impact on the cell sizes observed. Where material type far outweighed surface roughness in its effect on cell size.

Roze, Jonathan↗
DOE OSTI2024

PRODUCTION OF GLASS-TO-METAL SEALS USING ADDITIVE MANUFACTURING TECHNIQUES

Glass-to-metal (GtM) seals are hermetic barriers between glass and metal components, often used in the electronic and vacuum industries. Creating the seals traditionally requires heating all the components to the glass melting temperature, where the glass will flow and bond to the metal. Due to the manufacturing constraints of the individual components and sealing conditions there are geometric and material restrictions. Additive manufacturing techniques were used to make GtM seals to reduce these restrictions. Hermetic, single pin seals were produced using printed metal shells, by selective laser melting (SLM), and digital light processing (DLP) printed glass preforms. Glass preforms were printed with photosensitive resin mixed with a silicate sealing glass powder in a 1:2 weight ratio. Thermal analysis, TGA/DSC, and screening experiments were used to determine an organic removal schedule. Video techniques determined a sintering schedule by producing a densification curve at different isothermal holds which were fit with a viscous sintering model. Single pin seals were also produced use a laser assisted manufacturing (LAM) process as an alternative to the conventional furnace sealing process. A Nd:YAG laser was focused on a solid glass preform, heating the glass to form the glass-metal bond. The sealing glass was doped with a transition metal oxide, Fe2O3 or CuO, to increase absorption of the laser wavelength. The interface of hermetic LAM seals were analyzed using electron microscopy, compared to conventional prepared seals, finding a reduction of interfacial morphologies.

Read, Aaron Reece↗
NASA NTRS2022

Thermocouple Temperature Measurements in Selective Laser Melting Additive Manufacturing

The extreme thermal history resulting from selective laser melting leads to microstructural characteristics and residual stresses that have considerable impact on the mechanical behavior of the printed part. Accurate measurements of the temperature combined with thermal models are needed to better understand and control the thermal history to optimize mechanical properties. In order to calibrate and validate models, experimental temperature data must be accurately measured in a rapid fashion due to the high speeds of the laser. In this work, a novel method to read data from thermocouples is created with enhanced circuitry that achieves a sampling rate of 10 kHz. This data acquisition rate allows for high precision sampling of SLM heating and cooling cycles.

additive manufacturing↗
DOE OSTI2021

Direct observations and characterization of crack closure during microstructurally small fatigue crack growth via in-situ high-energy X-ray characterization

This study provides direct observation of the crack closure mechanism of a naturally occurring, tortuous, 3D microstructurally small fatigue crack (SFC) in additively manufactured Inconel 718. In-situ non-destructive characterization is performed using high-energy X-ray diffraction techniques to capture the evolution of the 3D microstructure and micromechanical response in the vicinity of the crack front. Based on the stress state of twelve grains analyzed at the crack tip, the crack closure events of the SFC front was found to be spatially heterogeneous with respect to loading progression governed by the local stress state of the grains (specifically the stress reversal from compression to tension). From this analysis, three grains that displayed different degrees of crack closure were further investigated, based on the orientation of the crack relative to the grains and the associated modality of crack growth. The stress normal to the crack plane and the associated degree of Mode I crack behavior were correlated with events of the crack opening earlier during the loading cycle. This was further corroborated by diffraction spot spreading analysis that quantified the crystallographic lattice distortion caused by the opening crack. Additionally, the detailed characterization of the opening behavior of the grains located at the crack tip and their associated states of stress elucidates the mechanism governing crack closure and will inform future modeling efforts of this phenomenon.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Non-destructive simulation of node defects in additively manufactured lattice structures

Additive Manufacturing (AM), commonly referred to as 3D printing, offers the ability to not only fabricate geometrically complex lattice structures but parts in which lattice topologies in-fill volumes bounded by complex surface geometries. However, current AM processes produce defects on the strut and node elements which make up the lattice structure. This creates an inherent difference between the as-designed and as-fabricated geometries, which negatively affects predictions (via numerical simulation) of the lattice’s mechanical performance. Although experimental and numerical analysis of an AM lattice’s bulk structure, unit cell and struts have been performed, there exists almost no research data on the mechanical response of the individual as-manufactured lattice node elements. Here we propose a methodology that, for the first time, allows non-destructive quantification of the mechanical response of node elements within an as-manufactured lattice structure. A custom-developed tool is used to extract and classify each individual node geometry from micro-computed tomography scans of an AM fabricated lattice. Voxel-based finite element meshes are generated for numerical simulation and the mechanical response distribution is compared to that of the idealised computer-aided design model. The method demonstrates compatibility with Uncertainty Quantification methods that provide opportunities for efficient prediction of a population of nodal responses from sampled data. Overall, the non-destructive and automated nature of the node extraction and response evaluation is promising for its application in qualification and certification of additively manufactured lattice structures.

36 MATERIALS SCIENCE↗
NASA NTRS2018

Fatigue Characteristics of Additively Manufactured Aerospace Materials

This presentation documents the fatigue properties of three additive manufactured (AM) metallic systems (Ti-6-4, GRC op-84, and Alloy 718) used by NASA in various aerospace applications. These alloys were produced using the powder bed method, with the titanium alloy using an electron beam melting (EBM) and the other two alloys using selective laser melting systems (SLM). For each material a large matrix of fatigue tests were conducted and the fatigue characteristics compared to their conventionally manufactured counterparts. Build orientations and resulting microstructures are discussed with respect to the tested mechanical properties.

Lerch, Brad↗
NASA NTRS2022

M2 Selective Laser Melting GRCop-42 Recycling Study

A powder recycling study was conducted to examine the effects of powder reuse on physical and mechanical properties of SLM GRCop-42. Twelve sequential builds were conducted, each reusing powder from the previous build topped off with virgin powder to fill the powder chamber. Powder morphology, particle size distribution, flowability, and chemistry were examined for each subsequent build, along with the mechanical properties of tensile and LCF specimens built with each powder batch. It was found that only powder flowability demonstrated a trend with increasing reuse, with flowability and cohesiveness generally decreasing over the course of the 12 builds. Minor variation in powder chemistry was observed throughout the study, however, the variations did not correlate with increasing powder reuse

Additive Manufacturing↗