Search NASA⌕ Search

SEARCH · Search NASA

Results for “silicon compounds”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

Characteristics of Elastomer Seals Exposed to Space Environments

A universal docking and berthing system is being developed by the National Aeronautics and Space Administration (NASA) to support all future space exploration missions to low-Earth orbit (LEO), to the Moon, and to Mars. The Low Impact Docking System (LIDS) is being designed to operate using a seal-on-seal configuration in numerous space environments, each having unique exposures to temperature, solar radiation, reactive elements, debris, and mission duration. As the LIDS seal is likely to be manufactured from an elastomeric material, performance evaluation of elastomers after exposure to atomic oxygen (AO) and ultraviolet radiation (UV) was conducted, of which the work presented herein was a part. Each of the three candidate silicone elastomer compounds investigated, including Esterline ELA-SA-401, and Parker Hannifin S0383-70 and S0899-50, was characterized as a low outgassing compound, per ASTM E595, having percent total mass loss (TML) less than 1.0 percent and collected volatile condensable materials (CVCM) less than 0.1 percent. Each compound was compatible with the LIDS operating environment of -50 to 50 C. The seal characteristics presented include compression set, elastomer-to-elastomer adhesion, and o-ring leakage rate. The ELA-SA-401 compound had the lowest variation in compression set with temperature. The S0383-70 compound exhibited the lowest compression set after exposure to AO and UV. The adhesion for all of the compounds was significantly reduced after exposure to AO and was further decreased after exposure to AO and UV. The leakage rates of o-ring specimens showed modest increases after exposure to AO. The leakage rates after exposure to AO and UV were increased by factors of up to 600 when compared to specimens in the as-received condition.

Daniels, Christopher C.↗
NASA NTRS2008

Performance of Subscale Docking Seals Under Simulated Temperature Conditions

A universal docking system is being developed by the National Aeronautics and Space Administration (NASA) to support future space exploration missions to low Earth orbit (LEO), to the moon, and to Mars. The candidate docking seals for the system are a composite design consisting of elastomer seal bulbs molded into the front and rear sides of a metal ring. The test specimens were subscale seals with two different elastomer cross-sections and a 12-in. outside diameter. The seal assemblies were mated in elastomer seal-on-metal plate and elastomer seal-on-elastomer seal configurations. The seals were manufactured from S0383-70 silicone elastomer compound. Nominal and off-nominal joint configurations were examined. Both the compression load required to mate the seals and the leak rate observed were recorded while the assemblies were subjected to representative docking system operating temperatures of -58, 73, and 122 F (-50, 23, and 50 C). Both the loads required to fully compress the seals and their leak rates were directly proportional to the test temperature.

Smith, Ian M.↗
NASA NTRS2010

Material Properties of Three Candidate Elastomers for Space Seals Applications

A next-generation docking system is being developed by the National Aeronautics and Space Administration (NASA) to support Constellation Space Exploration Missions to low Earth orbit (LEO), to the Moon, and to Mars. A number of investigations were carried out to quantify the properties of candidate elastomer materials for use in the main interface seal of the Low Impact Docking System (LIDS). This seal forms the gas pressure seal between two mating spacecraft. Three candidate silicone elastomer compounds were examined: Esterline ELA-SA-401, Parker Hannifin S0383-70, and Parker Hannifin S0899-50. All three materials were characterized as low-outgassing compounds, per ASTM E595, so as to minimize the contamination of optical and solar array systems. Important seal properties such as outgas levels, durometer, tensile strength, elongation to failure, glass transition temperature, permeability, compression set, Yeoh strain energy coefficients, coefficients of friction, coefficients of thermal expansion, thermal conductivity and diffusivity were measured and are reported herein.

Bastrzyk, Marta B.↗
NASA NTRS1998

Space Suit Survivability Enhancement NASA Research Announcement 96-OLMSA-01B: Advanced Life Support and Environmental Technologies for Human Exploration and Development of Space

Conducted two meetings to review the project scope and develop concepts for self-sealing material compositions, Focus has been on developing concepts that would seal a penetration enough to allow the astronauts to re-enter the spacecraft within the window provided by the emergency air supply. Concepts discussed include: quilted fabrics containing a viscous flow material in the quilted cells which would seal the bladder breach when forced to flow by the internal suit pressure; a sealant impregnated felt liner which acts similar to above; and a "blousy" fibrous layer which would mechanically plug a rupture under pressure. Illustrations of the above concepts are included in the attached viewgraphs, which were used in a presentation. The most promising of these concepts will be made into prototypes for testing. ILC has developed a test fixture to test the scaling characteristics of various material layups by measuring real-time changes in pressure and make-up flow in a pressurized cylinder. Candidate viscous sealing compounds such as silicones and urethanes have been identified. These compounds will be coated on existing bladder cloth for initial tests. The most promising compounds will be integrated into the above material structures for final testing. Design and analysis of fabric weaves to improve cut and puncture resistance of the suit TMG layers is underway. Philadelphia Textile is developing a mathematical model to correlate yarn type and weave structure to cut and tear resistance. The computer mathematical modeling of the fabric failure mechanisms by Cornell University, as originally proposed, will be replaced with the above model and empirical testing methods, due to the loss of key Cornell personnel.

Source record↗
DOE OSTI2024

Effects of Structure and Filler on Mechanical Properties of Direct Ink Write Pads

Direct ink write (DIW) is an extrusion-based additive manufacturing (AM) technique that enables superior repeatability, property tuning, and material customization compared to conventional manufacturing techniques. In this research, DIW is used to print silicone foams that must accommodate the thermal expansion of other parts. This expansion requires the material to compress and subsequently recover. Thus, a key performance metric is reducing “compression set” or deformation retained after the material is compressed. For this study, a silicone resin was compounded with a getter material, 1,4 bis(phenylethynyl)benzene (DEB) mixed with carbon-supported palladium (Pd) and printed in a variety of lattice structures. The effects of the filler and print structure on compression set were evaluated. In these experiments, 0.5-inch diameter coupons were compressed to 75% their original height for 22 hours at 70 °C, and the change in height calculated at intervals between 30 minutes and 24 hours post-decompression. The unfilled pad with skin layers had the best compression set at 0.7% ± 0.1%, followed by the unfilled pad with no skins at 1.5% ± 0.1%. As the number of filled layers increased, compression set performance degraded. The pad with filled skin layers and all filled layers had a compression set of 7.0% ± 0.3%. Additionally, the reaction extent of DEB was found to increase compression set, possibly due to the diffusion of DEB to the surface at elevated temperatures. Imaging reveals extensive crystallization at the surface. These investigations show that a non-reinforcing filler will increase compression set but that print structure can mitigate this effect.

36 MATERIALS SCIENCE↗
NASA NTRS1987

Modeling free convective gravitational effects in chemical vapor deposition

In this paper, a combined fluid-mechanics, mass-transport, and chemistry model describing CVD in an open-tube atmospheric-pressure flow reactor is developed. The model allows gas-phase reactions to proceed to equilibrium and accounts for finite reaction rates at the surface of the deposition substrate. This model is a useful intermediate step toward a model employing fully rate-limited chemistry. The model is used to predict the effects of free convection on flow patterns, temperature and species-concentration profiles, and local deposition rates for silicon deposited by silane pyrolysis. These results are discussed in terms of implications for CVD of silicon and other compounds, microgravity studies, and techniques for testing and validating the model.

Stinespring, C. D.↗
NASA NTRS1989

Advances in thin-film solar cells for lightweight space photovoltaic power

The present stature and current research directions of photovoltaic arrays as primary power systems for space are reviewed. There have recently been great advances in the technology of thin-film solar cells for terrestrial applications. In a thin-film solar cell the thickness of the active element is only a few microns; transfer of this technology to space arrays could result in ultralow-weight solar arrays with potentially large gains in specific power. Recent advances in thin-film solar cells are reviewed, including polycrystalline copper-indium selenide (CuInSe2) and related I-III-VI2 compounds, polycrystalline cadmium telluride and related II-VI compounds, and amorphous silicon:hydrogen and alloys. The best experimental efficiency on thin-film solar cells to date is 12 percent AMO for CuIn Se2. This efficiency is likely to be increased in the next few years. The radiation tolerance of thin-film materials is far greater than that of single-crystal materials. CuIn Se2 shows no degradation when exposed to 1 MeV electrons. Experimental evidence also suggests that most of all of the radiation damage on thin-films can be removed by a low temperature anneal. The possibility of thin-film multibandgap cascade solar cells is discussed, including the tradeoffs between monolithic and mechanically stacked cells. The best current efficiency for a cascade is 12.5 percent AMO for an amorphous silicon on CuInSe2 multibandgap combination. Higher efficiencies are expected in the future. For several missions, including solar-electric propulsion, a manned Mars mission, and lunar exploration and manufacturing, thin-film photovolatic arrays may be a mission-enabling technology.

Landis, Geoffrey A.↗
NASA NTRS1990

InAs/GaAs and InAs doping superlattices

The extension of the optical response of narrow band gap III-V semiconductors into the long wavelength infrared radiation (LWIR) regime for high sensitivity sensor applications is a challenging problem. Recent advances in nipi doped GaAs superlattices, lattice mismatched epitaxy and the heteroepitaxial growth of III-V compound semiconductors on silicon substrates offer a number of opportunities. Researchers describe two different device approaches based on the molecular beam epitaxy (MBE) growth of superlattice materials which are directed to LWIR focal plane array technology. The first of these uses nipi superlattices fabricated in bulk InAs which has been grown on either GaAs or Si substrates. The second is based on the growth of a new pseudomorphic tetragonal phase of InAs on GaAs to create a semimetal/semiconductor superlattice material.

Grunthaner, Frank J.↗
NASA NTRS1991

Thin-Film Photovoltaics: Status and Applications to Space Power

The potential applications of thin film polycrystalline and amorphous cells for space are discussed. There have been great advances in thin film solar cells for terrestrial applications; transfer of this technology to space applications could result in ultra low weight solar arrays with potentially large gains in specific power. Recent advances in thin film solar cells are reviewed, including polycrystalline copper iridium selenide and related I-III-VI2 compounds, polycrystalline cadmium telluride and related II-VI compounds, and amorphous silicon alloys. The possibility of thin film multi bandgap cascade solar cells is discussed.

Landis, Geoffrey A.↗
NASA NTRS1991

Applications of thin-film photovoltaics for space

The authors discuss the potential applications of thin-film polycrystalline and amorphous cells for space. There have been great advances in thin-film solar cells for terrestrial applications. Transfer of this technology to space applications could result in ultra low-weight solar arrays with potentially large gains in specific power. Recent advances in thin-film solar cells are reviewed, including polycrystalline copper indium selenide and related I-III-VI2 compounds, polycrystalline cadmium telluride and related II-VI compounds, and amorphous silicon arrays. The possibility of using thin-film multi-bandgap cascade solar cells is discussed.

Landis, Geoffrey A.↗
NASA NTRS1998

Profile Evolution Simulation in Etching Systems Using Level Set Methods

Semiconductor device profiles are determined by the characteristics of both etching and deposition processes. In particular, a highly anisotropic etch is required to achieve vertical sidewalls. However, etching is comprised of both anisotropic and isotropic components, due to ion and neutral fluxes, respectively. In Ar/Cl2 plasmas, for example, neutral chlorine reacts with the Si surfaces to form silicon chlorides. These compounds are then removed by the impinging ion fluxes. Hence the directionality of the ions (and thus the ion angular distribution function, or IAD), as well as the relative fluxes of neutrals and ions determines the amount of undercutting. One method of modeling device profile evolution is to simulate the moving solid-gas interface between the semiconductor and the plasma as a string of nodes. The velocity of each node is calculated and then the nodes are advanced accordingly. Although this technique appears to be relatively straightforward, extensive looping schemes are required at the profile corners. An alternate method is to use level set theory, which involves embedding the location of the interface in a field variable. The normal speed is calculated at each mesh point, and the field variable is updated. The profile comers are more accurately modeled as the need for looping algorithms is eliminated. The model we have developed is a 2-D Level Set Profile Evolution Simulation (LSPES). The LSPES calculates etch rates of a substrate in low pressure plasmas due to the incident ion and neutral fluxes. For a Si substrate in an Ar/C12 gas mixture, for example, the predictions of the LSPES are identical to those from a string evolution model for high neutral fluxes and two different ion angular distributions.(2) In the figure shown, the relative neutral to ion flux in the bulk plasma is 100 to 1. For a moderately isotropic ion angular distribution function as shown in the cases in the left hand column, both the LSPES (top row) and rude's string method (bottom row) predict tapered profiles. The LSPES uses an AD with a FWHM = 13.5 degrees, and rude's model uses a ratio of sheath voltage to ion temperature of 50. The more anisotropic IADs produce profiles with more vertical sidewalls and a wider bottom surface, as shown in the right hand column. Here, the LSPES has an AD with a FWHM = 2 degrees, and rude's model uses a ratio of 500 of sheath voltage to ion temperature. The agreement between the LSPES and rude's model is excellent in both cases. We will present etching profiles generated by the LSPES, including calculations of the re-emitted fluxes of both neutrals and ions off of the profile walls. In addition, we will show the effect of geometric structures (overhangs, etc.) on the etching profiles. Other physical aspects, such as surface diffusion, will also be included in the model.

Hwang, Helen H.↗
NASA NTRS2016

Application of the Molecular Adsorber Coating Technology on the Ionospheric Connection Explorer Program

The Molecular Adsorber Coating (MAC) is a zeolite based highly porous coating technology that was developed by NASA Goddard Space Flight Center (GSFC) to capture outgassed contaminants, such as plastics, adhesives, lubricants, silicones, epoxies, potting compounds, and other similar materials. This paper describes the use of the MAC technology to address molecular contamination concerns on NASAs Ionospheric Connection Explorer (ICON) program led by the University of California (UC) Berkeleys Space Sciences Laboratory. The sprayable paint technology was applied onto plates that were installed within the instrument cavity of ICONs Far Ultraviolet Imaging Spectrograph (FUV). However, due to the instruments particulate sensitivity, the coating surface was vibrationally cleaned through simulated acoustics to reduce the risk of particle fall-out contamination. This paper summarizes the coating application efforts on the FUV adsorber plates, the simulated laboratory acoustic level cleaning test methods, particulation characteristics, and future plans for the MAC technology.

outgassing↗
DOE OSTI2021

Electroabsorption optical modulator

An electroabsorption modulator that operates based on electroabsorption of a surface plasmon polariton mode is improved by various structural changes and/or selection of different materials. For example, at least a portion of the waveguide may be made to be conductive, e.g., by doping. Also, layers that make up the modulator structure may be placed along sides of waveguides in addition to or instead of simply on the top thereof. High permittivity gate dielectric materials may be employed. Also, materials other than ITO may be employed as a transparent conductor. Such an improved plasmonic electroabsorption modulator can be fabricated using standard semiconductor processing techniques and may be integrated with standard photonic integrated circuits, including silicon photonics and compound semiconductor-based platforms. Advantageously, high-speed, low-voltage operation over a wide spectrum of wavelengths may be achieved.

Wood, Michael↗
NASA NTRS1978

The room-temperature dissociation of the compound Au3Si

Three gold-18.6 at.% silicon specimens which were solidified by quenching from above the liquidus temperature have been reexamined after being stored at room temperature for about 8 years. It was found that the 'metastable' compound Au3Si formed on quenching had begun to dissociate by a surface nucleated, solid-state reaction. The reaction front had advanced about 0.2 mm from the surface, leaving a rim of dissociation products. These dissociation products were studied using optical and scanning electron microscopy, electron beam microprobe analysis and an X-ray micro-diffraction technique. It was concluded that the reaction produces elemental gold and silicon, as at higher reaction temperatures, but that the scale of dispersion is so extremely fine that the resulting microstructure cannot be resolved by scanning electron microscopy.

Bhattacharya, D.↗
NASA NTRS1984

Powder containing 2H-type silicon carbide produced by reacting silicon dioxide and carbon powder in nitrogen atmosphere in the presence of aluminum

The production of powder which contains silicon carbide consisting of 40% of 2H-type silicon carbide, beta type silicon carbide and less than 3% of nitrogen is discussed. The reaction temperature to produce the powder containing 40% of 2H-type silicon carbide is set at above 1550 degrees C in an atmosphere of aluminum or aluminum compounds and nitrogen gas or an antioxidation atmosphere containing nitrogen gas. The mixture ratio of silicon dioxide and carbon powder is 0.55 - 1:2.0 and the contents of aluminum or aluminum compounds within silicon dioxide is less than 3% in weight.

Kuramoto, N.↗