Search NASA⌕ Search

SEARCH · Search NASA

Results for “simulator motion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Helicopter Pilot Evaluations of the Airborne Collision Avoidance System Xr in a High-Fidelity Motion Simulation

New aircraft and aerial Urban Air Mobility operations require updated technologies to maintain vehicle separation during flight. Specifically, higher-density airspace will need more than traditional air traffic control to keep vehicles well clear of each other and avoid Near Midair Collisions. In response, the Federal Aviation Administration is currently developing the Airborne Collision Avoidance System X (ACAS X) for next-generation air traffic deconfliction, which provides caution-level and warning-level alerts in response to multiple aircraft types. This study recruited six helicopter pilots to fly an electric vertical takeoff and landing vehicle model in simulated operations under Visual Flight Rules (VFR). Flights were accomplished using the high-fidelity Vertical Motion Simulator at the NASA Ames Research Center. Participants controlled the vehicle using two side inceptors and foot rudders. The rotorcraft variant of ACAS X (ACAS Xr) was provided for alerting and guidance during traffic conflicts. Pilots used this system while giving feedback to the researchers through questionnaires, debriefs, and other discussions. Variables of interest to the study were phases of flight (i.e., Cruise, Hover, and Approach) and ACAS Xr configurations: The Collision Avoidance System configuration behaves similarly to current commercial traffic systems used for tactical deconfliction in crewed vehicles, and the Detect and Avoid configuration was developed to provide extra, corrective-level guidance for unmanned aircraft systems. Results showed that pilots found the alerting and guidance from ACAS Xr useful, effective, and acceptable for VFR operations. Certain elements, like speed guidance and text banners, were found to be of no use to the pilots. Hover and Approach scenarios were considered the most difficult for ACAS Xr alerting. Reasons for this difficulty were partially due to learning interference (i.e., overcoming previously learned behavior) and partially due to the vehicle model (i.e., NASA’s Lift Plus Cruise design). Still, alerting-based confounds reveal the need for more development for ACAS Xr during these Hover and Approach flight phases. Study caveats and future projects are discussed.

air taxis↗

The Effect of Fault Geometry and Minimum Shear Wavespeed on 3D Ground-Motion Simulations for an M w 6.5 Hayward Fault Scenario Earthquake, San Francisco Bay Area, Northern California

We investigated the effects of fault geometry and assumed minimum shear wavespeed (V Smin ) on 3D ground-motion simulations (0–2.5 Hz) in general, using a moment magnitude (M w ) 6.5 earthquake on the Hayward fault (HF). Simulations of large earthquakes on the northeast-dipping HF using the U.S. Geological Survey (USGS) 3D seismic model have shown intensity asymmetry with stronger shaking for the Great Valley Sequence east of the HF (hanging wall) relative to the Franciscan Complex to the west (footwall). We performed simulations with three fault geometries in both plane-layered (1D) and 3D models. Results show that the nonvertical fault geometries result in larger motions on the hanging wall relative to the vertical fault for the same Earth model with up to 50% amplifications in single-component peak ground velocity (PGV) within 10 km of the rupture. Near-fault motions on the footwall are reduced for the nonvertical faults, but less than they are increased on the hanging wall. Simulations assuming V Smin values of 500 and 250 m/s reveal that PGVs are on average 25% higher west of the HF when using the lower V Smin ,with some locations amplified by a factor of 3. Increasing frequency content from 2.5 to 5 Hz increases PGV values. Spectral ratios of these two V Smin cases show average amplifications of 2–4 (0.5–1.5 Hz) for the lower V Smin west of the fault. Large differences (up to 2×) in PGV across the HF from previous studies persist even for the case with a vertical fault or V Smin of 250 m/s. We conclude that assuming a V Smin of 500 m/s underestimates intensities west of the HF for frequencies above 0.5 Hz, and that low upper crustal (depth <10 km) shear wavespeeds defined in the 3D model contribute most to higher intensities east of the HF.

58 GEOSCIENCES↗

Comparison of a linear and a nonlinear washout for motion simulators utilizing objective and subjective data from CTOL transport landing approaches

Objective and subjective data gathered in the processes of comparing a linear and a nonlinear washout for motion simulators reveal that there is no difference in the pilot performance measurements used during instrument landing system (ILS) approaches with a Boeing 737 conventional takeoff and landing (CTOL) airplane between fixed base, linear washout, and nonlinear washout operations. However, the subjective opinions of the pilots reveal an important advance in motion cue presentation. The advance is not in the increased cue available over a linear filter for the same amount of motion base travel but rather in the elimination of false rotational rate cues presented by linear filters.

Parrish, R. V.↗

Effects of simulator motion and visual characteristics on rotorcraft handling qualities evaluations

The pilot's perceptions of aircraft handling qualities are influenced by a combination of the aircraft dynamics, the task, and the environment under which the evaluation is performed. When the evaluation is performed in a groundbased simulator, the characteristics of the simulation facility also come into play. Two studies were conducted on NASA Ames Research Center's Vertical Motion Simulator to determine the effects of simulator characteristics on perceived handling qualities. Most evaluations were conducted with a baseline set of rotorcraft dynamics, using a simple transfer-function model of an uncoupled helicopter, under different conditions of visual time delays and motion command washout filters. Differences in pilot opinion were found as the visual and motion parameters were changed, reflecting a change in the pilots' perceptions of handling qualities, rather than changes in the aircraft model itself. The results indicate a need for tailoring the motion washout dynamics to suit the task. Visual-delay data are inconclusive but suggest that it may be better to allow some time delay in the visual path to minimize the mismatch between visual and motion, rather than eliminate the visual delay entirely through lead compensation.

Mitchell, David G.↗

A time lag study of the vertical motion simulator computer system

A study was performed to evaluate an experimental method to determine time lags in real-time computer systems as the one associated with the Vertical Motion Simulator at Ames Research Center. The approach was to use an ordinary frequency analyzer to measure the phase difference between inputs and outputs of the computer system. The various elements of the program and computational architecture were modeled. Various factors, such as computer frame time and input frequency, were varied so that they were representative of the operational use of the simulator facilities. Experimentally determined results were compared with predictions derived from the simulation models. The results indicate that the frequency analyzer can be readily used to evaluate time lags in systems of this type. Differences between predicted and measured phase values indicate that the hardware and software imparts a time lag of about 5 msec to this facility.

Cleveland, W. B.↗

An actuator extension transformation for a motion simulator and an inverse transformation applying Newton-Raphson's method

A set of equations which transform position and angular orientation of the centroid of the payload platform of a six-degree-of-freedom motion simulator into extensions of the simulator's actuators has been derived and is based on a geometrical representation of the system. An iterative scheme, Newton-Raphson's method, has been successfully used in a real time environment in the calculation of the position and angular orientation of the centroid of the payload platform when the magnitude of the actuator extensions is known. Sufficient accuracy is obtained by using only one Newton-Raphson iteration per integration step of the real time environment.

Dieudonne, J. E.↗

Coordinated adaptive filters for motion simulators.

A new approach to providing motion drive signals to a flight simulator utilizing coordinated adaptive filters is presented. Some motivation for the use of coordinated washout is discussed, along with conditions that determine the burden of coordination. The coordinated adaptive filters are derived, based on continuous steepest descent, and the application of the filters to simulated flight data is demonstrated.

Parrish, R. V.↗

Implementation of Motion Simulation Software and Visual-Auditory Electronics for Use in a Low Gravity Robotic Testbed

The Jet Propulsion Laboratory (JPL) is developing the All-Terrain Hex-Limbed Extra-Terrestrial Explorer (ATHLETE) to assist in manned space missions. One of the proposed targets for this robotic vehicle is a near-Earth asteroid (NEA), which typically exhibit a surface gravity of only a few micro-g. In order to properly test ATHLETE in such an environment, the development team has constructed an inverted Stewart platform testbed that acts as a robotic motion simulator. This project focused on creating physical simulation software that is able to predict how ATHLETE will function on and around a NEA. The corresponding platform configurations are calculated and then passed to the testbed to control ATHLETE's motion. In addition, imitation attitude, imitation attitude control thrusters were designed and fabricated for use on ATHLETE. These utilize a combination of high power LEDs and audio amplifiers to provide visual and auditory cues that correspond to the physics simulation.

gravity↗

A piloted evaluation of an oblique-wing research aircraft motion simulation with decoupling control laws

The NASA Ames Research Center developed an oblique-wing research plane from NASA's digital fly-by-wire airplane. Oblique-wing airplanes show large cross-coupling in control and dynamic behavior which is not present on conventional symmetric airplanes and must be compensated for to obtain acceptable handling qualities. The large vertical motion simulator at NASA Ames-Moffett was used in the piloted evaluation of a proposed flight control system designed to provide decoupled handling qualities. Five discrete flight conditions were evaluated ranging from low altitude subsonic Mach numbers to moderate altitude supersonic Mach numbers. The flight control system was effective in generally decoupling the airplane. However, all participating pilots objected to the high levels of lateral acceleration encountered in pitch maneuvers. In addition, the pilots were more critical of left turns (in the direction of the trailing wingtip when skewed) than they were of right turns due to the tendency to be rolled into the left turns and out of the right turns. Asymmetric side force as a function of angle of attack was the primary cause of lateral acceleration in pitch. Along with the lateral acceleration in pitch, variation of rolling and yawing moments as functions of angle of attack caused the tendency to roll into left turns and out of right turns.

Kempel, Robert W.↗

Evaluating and Improving the USGS 3D Seismic Velocity Model in the San Francisco East Bay by Integrating Earthquake Ground-Motion Simulations and Noise-Derived Empirical Green's Functions

Simulations of scenario earthquake ground motions play an increasingly important role in improving seismic hazard assessment. In the San Francisco Bay Area (SFBA) the USGS has developed a 3D geologic/seismic model. Simulations of large magnitude (M) 7 Hayward Fault scenario earthquakes show dramatic differences in peak ground motions across the fault, arising from wavespeed differences, which highlights the need to evaluate the model. Our comparison of observed and simulated waveforms from M 4 SFBA earthquakes reveals bias in the travel times of direct S-waves for paths crossing the East Bay Hills, east of Hayward Fault, suggests that the shear wavespeeds in the upper crust of the USGS 3D model are too low, resulting in large delay times of S-wave arrivals at the East Bay Hills. We also retrieved noise-derived Green's functions (NGFs) and examined the path-specific bias in the USGS 3D model. We systematically compared synthetic waveforms with the 3D velocity model and observed NGFs. Our result shows that the time lags between the synthetic and observed data ranging from 2-5 seconds for the ray paths propagating the East Bay Hills. This result also suggests that the SFBA 3D model generates arrivals that are too slow. Additionally, we evaluate the Rayleigh-wave ellipticity to evaluate the subsurface velocity beneath seismic stations. A lateral variation in Rayleigh-wave ellipticity across the Hayward fault is observed, which will contribute to refine the SFBA 3D velocity model.

58 GEOSCIENCES↗

Coordinated adaptive washout for motion simulators.

This paper introduces a new method of providing motion cues to a moving base six-degree-of-freedom flight simulator utilizing nonlinear filters. Coordinated adaptive filters, used to coordinate translational and rotational motion, are derived based on the method of continuous steepest descent, and the basic concept of the digital controllers used for the uncoordinated heave and yaw cues is also presented. The coordinated adaptive washout method is illustrated by an application in a six-degree-of-freedom fixed-base environment.

Parrish, R. V.↗

Helicopter Flight Simulation Motion Platform Requirements

To determine motion fidelity requirements, a series of piloted simulations was performed. Several key results were found. First, lateral and vertical translational platform cues had significant effects on fidelity. Their presence improved performance and reduced pilot workload. Second, yaw and roll rotational platform cues were not as important as the translational platform cues. In particular, the yaw rotational motion platform cue did not appear at all useful in improving performance or reducing workload. Third, when the lateral translational platform cue was combined with visual yaw rotational cues, pilots believed the platform was rotating when it was not. Thus, simulator systems can be made more efficient by proper combination of platform and visual cues. Fourth, motion fidelity specifications were revised that now provide simulator users with a better prediction of motion fidelity based upon the frequency responses of their motion control laws. Fifth, vertical platform motion affected pilot estimates of steady-state altitude during altitude repositioning. Finally, the combined results led to a general method for configuring helicopter motion systems and for developing simulator tasks that more likely represent actual flight. The overall results can serve as a guide to future simulator designers and to today's operators.

Schroeder, Jeffery Allyn↗

Strong Ground Motion Simulations of the M7.1 Kumamoto, Japan Earthquake Using Characterized Heterogeneous Source Models

The objective of our study is to analyze the performance of characterized heterogeneous rupture models in simulations of near-fault ground motion from the M7 Kumamoto, Japan earthquake, using Graves and Pitarka (2016) broad-band simulation method. We developed a kinematic earthquake rupture generator that combines the Graves and Pitarka (2016) (GP2016) rupture model with the multiple asperity characterized rupture model of Irikura and Miyake (IM2011), also known as Irikura recipe (Irikura and Miyake, 2011). The proposed kinematic rupture model incorporates distinct features of both original rupture models such as small-scale stochastic rupture variability, and shallow areas with large slip separated from areas with high sliprate, inherited from the GP2016, and desired near-fault large-scale rupture directivity effects produced by the multiple asperity model IM2011.

58 GEOSCIENCES↗

An experimental study of sound radiation from a subsonic jet in simulated motion

A free-jet anechoic facility is used for quantitative determination of the effect of motion on the pure jet mixing noise from subsonic jets. The farfield measurements obtained outside the free jet are subjected to amplitude and angle corrections due to free-jet shear layer refraction; in addition, corrections are made to account for the distributed nature of the jet noise source as a function of frequency. The corrected results, which provide the changes in the jet mixing noise as a result of simulated jet motion, are presented for a range of jet velocities with a fixed free-jet velocity. Comparisons are made between the findings obtained and those related to other simulation and flight measurements. The results indicate that the effect of motion is to reduce jet mixing noise at all angles of measurement, and the reduction is broadband with the largest magnitude occurring around the spectral peak.

Yu, J. C.↗

Applicability of 1D site response analysis to shallow sedimentary basins: A critical evaluation through physics-based 3D ground motion simulations

One-dimensional site response analysis (1D SRA) remains the standard practice in considering the effect of local soil deposits and predicting site-specific ground motions, although its range of applicability to realistic seismic wavefields is still in question. In this 1D approach, horizontal and vertical ground shaking are assumed to be induced by vertically propagating shear and compressional waves, respectively. A recent study based on analytical two-dimensional (2D) plane waves and simple point source earthquake simulations has shown two mechanistic limitations in this 1D modelling technique for general inclined seismic waves, that is, systematic over-prediction of the vertical motion and wave trapping in the 1D soil column. In this article, we evaluate in detail the applicability of this 1D modelling approach to realistic three-dimensional (3D) simulated seismic wavefields in shallow sedimentary basins. Linear-viscoelastic 1D SRA predictions using two types of input motions that are commonly used in practice—rock outcrop and in-column motions, are compared with the reference true site response results from 3D earthquake simulations in terms of various measures in the frequency and time domain. It is shown that the horizontal motion in the 3D seismic wavefield exhibits dominant shear wave propagation phenomenon, while the vertical motion is a combined effect of compressional and shear waves and can be over-predicted by the 1D approach when the incident seismic waves are inclined. Direct evidence of the wave refraction process that leads to the vertical motion over-prediction is provided. 1D SRA with in-column inputs can yield motions that have significantly longer duration compared to the true 3D site response solution due to trapped waves, casting in doubt the frequent need for increased soil damping in existing site studies to compensate for wave attenuation due to scattering alone. Sensitivity investigation on the increase of soil profile damping by a multiplier D mul shows D mul values compatible with those found in the literature for both horizontal and vertical motions. It is shown that the level of D mul optimized for a best match of the spectral acceleration is dependent on the characteristic of the input motion and a larger D mul is typically required for the vertical component. In contrast, 1D SRA with outcrop motions predicts motions with shorter significant duration due to its inability to capture the basin-edge generated surface waves. A suite of ground motion simulations was performed to assess the sensitivity of the observations to the basin geologic structure including the velocity gradient, rock-basin impedance contrast and basin depth. The analysis results show that the accuracy of the simplified 1D procedure is dependent on the wavefield composition of both the input motions and the true 3D site response solution. While the horizontal motions in shallow sedimentary basins can, to the first order, be reasonably captured by the simplified 1D approach, 1D SRA for the vertical component is in general not reliable and contributions from inclined shear waves should be accounted for in site-specific evaluation of the vertical design ground motion.

1D assumption↗

Initial Evaluations of LoC Prediction Algorithms Using the NASA Vertical Motion Simulator

Flying near the edge of the safe operating envelope is an inherently unsafe proposition. Edge of the envelope here implies that small changes or disturbances in system state or system dynamics can take the system out of the safe envelope in a short time and could result in loss-of-control events. This study evaluated approaches to predicting loss-of-control safety margins as the aircraft gets closer to the edge of the safe operating envelope. The goal of the approach is to provide the pilot aural, visual, and tactile cues focused on maintaining the pilot's control action within predicted loss-of-control boundaries. Our predictive architecture combines quantitative loss-of-control boundaries, an adaptive prediction method to estimate in real-time Markov model parameters and associated stability margins, and a real-time data-based predictive control margins estimation algorithm. The combined architecture is applied to a nonlinear transport class aircraft. Evaluations of various feedback cues using both test and commercial pilots in the NASA Ames Vertical Motion-base Simulator (VMS) were conducted in the summer of 2013. The paper presents results of this evaluation focused on effectiveness of these approaches and the cues in preventing the pilots from entering a loss-of-control event.

Pilot Cue↗